For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. Th...For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al_2O_3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface.展开更多
The separation process of non-metallic inclusions at the steel–slag interface was simulated by physical modeling. Three different kinds of particles(octahedral, plate-like, and spherical) and three different oils(ker...The separation process of non-metallic inclusions at the steel–slag interface was simulated by physical modeling. Three different kinds of particles(octahedral, plate-like, and spherical) and three different oils(kerosene, bean oil, and pump oil) were used to model inclusions and slags, respectively. The effects of inclusion geometry(shape and size) and slag properties(viscosity and interfacial tension) on the separation process were investigated. The results revealed that the variation of surface free energy and the viscosity of the slag are two significant factors affecting the separation process of inclusions at the steel–slag interface. The variation of surface free energy helped inclusions enter the slag phase, whereas the decrease of slag viscosity shortened the separation time. The deformation of the steel–slag interface could give rise to the resistance force, which would resist inclusions passing through the interface. A liquid film formed on the inclusion as it passed through the steel–slag interface, which might be related to the inclusion's shape.展开更多
Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time larg...Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time largely affected non-metallic inclusions.With the reaction time increased from 30 min to 90 min in laboratory study,MgO-Al_2O_3 spinels were gradually changed into CaO-MgO-Al_2O_3 system inclusions surrounded by softer CaO-Al_2O_3 surface layers.By using high basicity slag which contained as much as 41%Al_2O_3 in the laboratory study,ratio of low melting temperature CaO-MgO-Al_2O_3 system inclusions was remarkably increased to above 80%.In the industrial experiment,during the secondary refining,the inclusions changed in order of 'Al_2O_3→MgO-Al_2O_3→CaO-MgO-Al_2O_3'.Through the LF and RH refining,most inclusions could be transferred to lower melting temperature CaO-Al_2O_3 and CaO-MgO-Al_2O_3 system inclusions.展开更多
Buried pipelines are an essential component of the urban infrastructure of modern cities.Traditional buried pipes are mainly made of metal materials.With the development of material science and technology in recent ye...Buried pipelines are an essential component of the urban infrastructure of modern cities.Traditional buried pipes are mainly made of metal materials.With the development of material science and technology in recent years,non-metallic pipes,such as plastic pipes,ceramic pipes,and concrete pipes,are increasingly taking the place of pipes made from metal in various pipeline networks such as water supply,drainage,heat,industry,oil,and gas.The location technologies for the location of the buried metal pipeline have become mature,but detection and location technologies for the non-metallic pipelines are still developing.In this paper,current trends and future perspectives of detection and location of buried non-metallic pipelines are summarized.Initially,this paper reviews and analyzes electromagnetic induction technologies,electromagnetic wave technologies,and other physics-based technologies.It then focuses on acoustic detection and location technologies,and finally introduces emerging technologies.Then the technical characteristics of each detection and location method have been compared,with their strengths and weaknesses identified.The current trends and future perspectives of each buried non-metallic pipeline detection and location technology have also been defined.Finally,some suggestions for the future development of buried non-metallic pipeline detection and location technologies are provided.展开更多
Dear Editor,I write to present one case report of a patient suffered the panophthalmitis caused by non-metallic foreign body with no etiologic agent and recovered quickly by phacoemulsification and vitrectomy with sil...Dear Editor,I write to present one case report of a patient suffered the panophthalmitis caused by non-metallic foreign body with no etiologic agent and recovered quickly by phacoemulsification and vitrectomy with silicone oil tamponade.Ocular trauma remains a major cause of blindness, particularly in the working-age population.展开更多
In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis ...In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis extraction method with a settled coulometer. In the research,the extraction effects of non-metallic inclusions in different electrolysis systems were studied, and it was concluded that alkalescent 2% TEA non-aqueous electrolyte was applicable for extracting most of non-metallic inclusion particles in steel. And then, in order to ensure the microscopic characterization and statistical calculation of inclusion particles, some electrolysis parameters should be confirmed, such as the size of the sample, control of the electrolysis mass, electric current, etc. Furthermore, for preventing the disturbance of carbides and presenting clear three-dimensional appearance by microscopic characterization, magnetic separation was utilized to separate the inclusion particles from carbides, which was useful for getting more veracious types, particle sizes and chemical composition of inclusions. Moreover, through calculation of quantity and particle size of inclusions in continuous determinate fields, the total quantity per unit volume or area and the particle size distribution of inclusions could be acquired by conversion with electrolysis loss. Besides, the comparison between this method and traditional quantitative metallography was also discussed, and finally, a conclusion was drawn that both of them have respectively applications in characterizing inclusions.展开更多
Precipitable Water Vapor(PWV)constitutes a pivotal parameter within the domains of atmospheric science,and remote sensing due to its profound influence on Earth’s climate dynamics and weather patterns.It exerts a sig...Precipitable Water Vapor(PWV)constitutes a pivotal parameter within the domains of atmospheric science,and remote sensing due to its profound influence on Earth’s climate dynamics and weather patterns.It exerts a significant impact on atmospheric stability absorption and emission of radiation,thus engendering alterations in the Earth’s radiative equilibrium.As such,precise quantification of PWV holds the potential to enhance weather prognostication and fortify preparedness against severe meteorological phenomena.This study aimed to elucidate the spatial and temporal changes in seasonal and annual PWV across the Indus River Basin and its sub-basins using ERA5 reanalysis datasets.The present study used ERA5 PWV(entire atmospheric column),air temperature at 2 m(t2m)and 500 hPa(T_500hPa),evapotranspiration,and total cloud cover data from 1960 to 2021.Theil Sen slope estimator and Mann-Kendall test were used for trend analysis.Correlation and multiple regression methods were used to understand the association of PWV with other factors.The findings have unveiled the highest increase in mean PWV during the monsoon(0.40 mm/decade),followed by premonsoon(0.37 mm/decade),post-monsoon(0.27 mm/decade),and winter(0.19 mm/decade)throughout the study period.Additionally,the mean PWV exhibited the most pronounced positive trend in the sub-basin Lower Indus(LI),followed by Panjnad(P),Kabul(K),and Upper Indus(UI)across all seasons,except winter.Annual PWV has also risen in the Indus basin and its sub-basins over the last six decades.PWV exhibits a consistent upward trend up to an elevation of 3500 m within the basin which is most pronounced during the monsoon season,followed by the pre-monsoon.The escalating PWV within the basin is reasonably ascribed to increasing air temperatures,augmented evapotranspiration,and heightened cloud cover.These findings hold potential utility for pertinent authorities engaged in water resource management and planning.展开更多
In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Pro...In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further.展开更多
Non-metallic inclusions,especially the large ones,within P/M Ni-base superalloy have a major influence on fatigue characteristics,but are not directly measurable by routine inspection.In this paper,a method,automatic ...Non-metallic inclusions,especially the large ones,within P/M Ni-base superalloy have a major influence on fatigue characteristics,but are not directly measurable by routine inspection.In this paper,a method,automatic image analysis,is proposed for estimation of the content,size and amount of non-metallic inclusions in superalloy.The methodology for the practical application of this method is described and the factors affecting the precision of the estimation are discussed.In the experiment,the characteristics of the non-metallic inclusions in Ni-base P/M superalloy are analyzed.展开更多
Focusing on the extending length restriction of the completion screen pipe resistance running into ultra-short radius horizontal well,this paper proposed technology of hydraulic drive completion tubular string running...Focusing on the extending length restriction of the completion screen pipe resistance running into ultra-short radius horizontal well,this paper proposed technology of hydraulic drive completion tubular string running into ultra-short radius horizontal well.Innovative hydraulic drive tools and string structure are designed,which are composed of guide tubing,hydraulic drive tubing and non-metallic completion screen pipe from inside to outside.A novel mechanical-hydraulic coupling model is established.Based on the wellbore structure of an ultra-short radius horizontal well for deep coalbed methane,the numerical calculations of force and hydraulic load on tubular strings were accomplished by the mechanical-hydraulic coupling model.The results show that the extending length of completion tubular string with the hydraulic drive is 17 times that of conventional completion technology under the same conditions.The multi-factor orthogonal design is adopted to analyze the numerical calculations,and the results show that the extending length of the completion tubular string is mainly affected by the completion tubular string structure and the friction coefficient between the non-metallic composite continuous screen pipe and the wellbore.Two series of hydraulic drive completion tubular string structures suitable for ultra-short radius horizontal wells under different conditions are optimized,with the extending limits of 381 m and 655 m,respectively.These researches will provide theoretical guidance for design and control of hydraulic drive non-metallic composite continuous completion screen pipe running into ultra-short radius horizontal wells.展开更多
In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The lar...In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The largest size of inclusions in the casting and the thermodynamic possibility of TiN precipitation in steel were also calculated. The results show that sulfide inclusions are evenly distributed and the content is low. The amount of oxide inclusions in CIESC: 4Cr5MoSiV1 steel is close to the ESR steel and lower than that in the EAF steel, and there are some differences along radial direction. Nitride inclusions are fine and the diameter of the largest one is 3-1 mum. With the increase of the centrifugal machine's rotational speed, the ratio of round inclusions increases and the ratio of sharp inclusions decreases. According to the experiment and the calculation results, it is pointed out that the largest diameter of non-metallic inclusions in the CIESC 4Cr5MoSiV1 casting is only 6.6 mum, and [N%][Ti%] in 4Cr5MoSiV1 steel should be controlled less than 4.4x 10(-5) in order to further reduce the amount and size of TiN inclusions.展开更多
Six different kinds of non-metallic or organic disinfectants were obtained in this research study including “Neutral Electrolyzed Water”, “M22” organic disinfectant solution, Superoxy Food Wash disinfectant, Hydro...Six different kinds of non-metallic or organic disinfectants were obtained in this research study including “Neutral Electrolyzed Water”, “M22” organic disinfectant solution, Superoxy Food Wash disinfectant, Hydrogen Peroxide, Clorox Germicidal Bleach and Clidox-S. The effectiveness of these disinfectants was studied against various subtypes of avian influenza virus (AIV). The virus-disinfectant mixtures were prepared in serial dilutions of each disinfectant with a constant virus titer and incubated at ambient temperature in different time intervals for virus inactivation. The virus inactivation results were determined by virus recovery in embryonating chicken eggs. Among the six different kinds of nonmetallic disinfectants obtained for this research project, Neutral Electrolyzed Water, “M22” solution, Clorox Germicidal Bleach and Clidox-S were effectively inactivated AIV with appropriate working dilutions and reaction times. Superoxy Food Wash disinfectant and Hydrogen Peroxide were found having limited effect on virus inactivation with extended exposure times of more than 2 hours. These research findings provide scientific data to poultry industry with guidelines to select and use non-metallic organic disinfectants for poultry flock sanitation and disinfection to effectively prevent and control of avian influenza outbreaks.展开更多
The Indus river basin(IRB)is one of the most depleted water basins globally,having significant challenges for its water sector.Monitoring of stable isotope composition(δ^(18)O and δ^(2)H)across IRB is a critical asp...The Indus river basin(IRB)is one of the most depleted water basins globally,having significant challenges for its water sector.Monitoring of stable isotope composition(δ^(18)O and δ^(2)H)across IRB is a critical aspect that can provide deeper insights for investigating complex hydrological processes.This work analyses the spatial pattern of the isotopic signature using a comprehensive compilation of available datasets of the Global Network of Isotopes in River(GNIR)and Global Network of Isotopes in Precipitation(GNIP),along with the previously published isotopic studies in the Indus basin.Additionally,this work provides a detailed comparison of the isotopic signature of the Upper Indus Basin(UIB),and Lower Indus Basin(LIB).The IRBs waterline was found to beδ^(2)H=7.89×δ^(18)O+13.51,which shows a close similarity with the Global Meteoric Water Line(GMWL),indicating the meteoric origin of the water with insignificant secondary evaporation prevailing across the basin.The Main Indus Channel(MIC)river water line(δ^(2)H=8.88×δ^(18)O+26.05)indicates a major contribution from the meteoric origin(precipitation/rain)of water with minimal effect of evaporation processes.The water line for UIB samples,(δ^(2)H=7.88×δ^(18)O+11.94)was found to be moderately higher in slope than LIB samples(δ^(2)H=7.17×δ^(18)O+7.16).However,the slopes of both UIB and LIB river water lines closely approached the slope of GMWL and were consistent with the slope of IRB water line,which indicates similarity in contribution of water sources.The higher slope and intercept in UIB suggest that meteoric water sources contributed to streamflow viz.from snow/glacier with insignificant evapotranspiration,which is also validated by the scarce vegetation cover in the UIB.However,the lower slope and intercept in LIB suggest stream water contribution from significantly evaporated groundwater and precipitation with a complete homogenization of discharge coming from the UIB.Results substantiate that distinct isotopic signatures found in different stretches of the IRB and along the MIC are caused by variations in basin characteristics,hydro-meteorological processes,water mixing,and minor influence of anthropogenic variables.展开更多
Developing high-performing non-noble transition metal catalysts for H_(2) evolution from chemical hydrogen storage materials is of great significance for the hydrogen economy system, yet challenging. Herein,we present...Developing high-performing non-noble transition metal catalysts for H_(2) evolution from chemical hydrogen storage materials is of great significance for the hydrogen economy system, yet challenging. Herein,we present for the first time that anomalous metastable hexagonal close-packed Ni nanoparticles induced by heteroatom N doping encapsulated in carbon(N-hcp-Ni/C) can exhibit admirable catalytic performance for ammonia borane(AB) dehydrogenation, prominently outperforming conventional fcc Ni counterpart with similar morphology and favorably presenting the state-of-the-art level.Comprehensive experimental and theoretical studies unravel that unusual hcp phase engineering of Ni together with N doping could induce charge redistribution and modulate electronic structure, thereby facilitating H_(2)O adsorption and expediting H_(2)O dissociation(rate-determining step). As a result, AB dehydrogenation can be substantially boosted with the assistance of N-hcp-Ni/C. Our proposed strategy highlights that unconventional crystal phase engineering coupled with non-metal heteroatom doping is a promising avenue to construct advanced transition metal catalysts for future renewable energy technologies.展开更多
Land surface temperature(LST)is a crucial parameter for understanding the Earth's surface energy balance,which provides insights into climate dynamics and local environmental conditions.Thus,the present study aims...Land surface temperature(LST)is a crucial parameter for understanding the Earth's surface energy balance,which provides insights into climate dynamics and local environmental conditions.Thus,the present study aims to evaluate the spatial and elevation-wise trends in the daytime,nighttime,and mean LST across the Indus River Basin(IRB)using MODIS 8-day product for the period between 2002 and 2022.The elevation,cloud cover,and land cover type data are used for explaining the emerging LST trends.The Theil slope estimator and MannKendall significance test were used for estimating the seasonal and annual LST trends.The findings show warming in mean daytime(0.020-0.024℃/yr)(except winter and post-monsoon),nighttime(0.013-0.049℃/yr),and mean(0.001-0.042℃/yr)LST in all the seasons(highest in monsoon).The annual mean nighttime LST(0.025℃/yr)is rising significantly faster than the mean daytime LST(0.0016℃/yr),showing the presence of a“nighttime warming effect”,which possibly increases human discomfort,particularly during the warm pre-monsoon and humid monsoon season.Elevation-dependent warming(EDW)is predominant in mean daytime LST in two elevation zones,namely(i)0-3 km and(ii)above 4 km,in all seasons,except in post-monsoon.In contrast,EDW in mean nighttime LST is observed up to 3 km and above 6 km in the basin in all the seasons,excluding post-monsoon.The warming trend in LST may be attributed to rising atmospheric moisture,cloud cover,declining snow cover,and changes in land cover to non-vegetated land.However,further investigations will involve exploring the underlying factors contributing to the observed anomalies in nighttime LST,considering variables such as regional energy balance and atmospheric stability.This research contributes to an understanding of the thermal dynamics in the mountain basin,aiding in climate studies,land management,and the development of effective adaptation strategies in the IRB.展开更多
Climate change differentially influences the frozen ground,a major dynamic component of the cryosphere,on a local and regional scale.Under the warming climate with pronounced effects reported at higher altitudes,the c...Climate change differentially influences the frozen ground,a major dynamic component of the cryosphere,on a local and regional scale.Under the warming climate with pronounced effects reported at higher altitudes,the characterization of the frozen ground is very important in the Upper Indus Basin(UIB),an important and critical region with respect to climate and hydro-glaciological dynamics.In this study,the efficiency and reliability of the surface frost number model are assessed in delineating the spatial extent of different classes of frozen ground in the region.The daily MODIS land surface temperature(LST)with ground surface temperature(GST)and surface geomorphological expressions as ground validation datasets are used jointly in efficiently determining the extent of different classes of frozen ground(continuous and discontinuous permafrost and seasonal frost).The LST and GST resonate with each other in the annual cycle of temperature variation,however,with mean annual LST exhibiting an offset(cold bias)of 5 to 7℃relative to mean GST.This study shows that the highest permafrost extent is observed in areas where the lowest thinning rates of glacier ice are reported and vice versa.The surface frost number model categorizes an area of 38%±3%and 15%±3%in the UIB as permafrost and seasonal frost,respectively.Based on the altitude model,the lower limit of alpine permafrost is approximated at a mean altitude of 4919±590 m a.s.l.in the UIB.The present study acts as preliminary work in the data sparse and inaccessible regions of the UIB in characterizing the frozen and unfrozen ground and may act as a promising input data source in glaciohydro-meteorological models for the Himalaya and Karakoram.In addition,the study also underlines the consideration of this derelict cryospheric climatic variable in defining and accounting for the sustainable development of socio-economic systems through its intricate ramification on agricultural activity,landscape stability and infrastructure.展开更多
The expansion parts and components of non-metallic in devices have become a fait accompli. In the case parts, components of non-metallic are used in atmospheres explosive and may be a potential source of ignition [1]....The expansion parts and components of non-metallic in devices have become a fait accompli. In the case parts, components of non-metallic are used in atmospheres explosive and may be a potential source of ignition [1]. Ignition hazards due to static electricity from the charged non-conductive non-metallic materials are well known [2]. The prevalence protection metal parts and components of anti-corrosion exist in any device equipped with a metal casing. Inherent risks associated services are caused by static electricity. Electrostatic phenomena arise in many situations, in a variety of environments and industries. The occurrence of charge static in many cases unexpected is unwanted and requires the use of expensive preventive measures. Brush discharge and propagating brush discharge (e.g. composite coating about non-conductive electrostatic properties of an isolated base conductive) create explosion hazard in underground endangered by firedamp and/or coal dust [3].展开更多
The Sohnari Member of the Early Eocene Laki Formation is massively deposited in the Southern Indus Basin of Pakistan and is considered a potential source rock to generate hydrocarbons.However,the detailed paleoclimati...The Sohnari Member of the Early Eocene Laki Formation is massively deposited in the Southern Indus Basin of Pakistan and is considered a potential source rock to generate hydrocarbons.However,the detailed paleoclimatic,paleoweathering,and depositional conditions of the Sohnari Member have not been studied earlier.This research mainly discusses the detailed mineralogical(bulk and clay)and elemental geochemistry of the Laki Formation from two outcrop sections(Jhimpir and Lakhra)in the Southern Indus Basin,Pakistan.The bulk minerals,including quartz(low),hematite,calcite,halite,gypsum,and clay minerals such as kaolinite,chlorite,smectite and illite have been discussed here.These results demonstrate the paleo-environment of studied area was arid with enhanced saline and weak to strong oxidizing depositional conditions.The chemical index of alteration(CIA)values in Jhimpir and Lakhra sections are in the ranges of 41.30-97.93 and 22.30-96.19,respectively,indicating that the Sohnari sediments experienced weak to intense chemical weathering in the source area.The interpretation of the A-CN-K ternary diagram is consistent with the clay mineral contents in the studied sediments,which is characterized by the predominance of kaolinite,gibbsite and chlorite,demonstrating the weak to strong weathering state under warm and humid climatic conditions.The chemical indices such as Sr/Ba,δU,V/Cr,Ni/Co,and Cu/Zn,U/Th and Ba/Ga show that Sohnari rocks of Early Eocene Laki Formation underwent strong evaporation,oxic water column with warm to humid and minor contact of cold climatic conditions.Based on our present data,it can be concluded that the sediments of Sohnari Member of Laki Formation from Jhimpir and Lakhra areas of Southern Indus Basin in Pakistan are related to Indio-Eurasian collision and came from the Indian shield rocks that were deposited in a brackish water body with a minor contact of the freshwater oxidizing paleo-environment depositional conditions.展开更多
Indus basin hosts many significant mineral deposits like gypsum and cement raw materials, gemstones, iron, coal, marble, dimension and construction stones, petroleum and water resources, world class pink salt and othe...Indus basin hosts many significant mineral deposits like gypsum and cement raw materials, gemstones, iron, coal, marble, dimension and construction stones, petroleum and water resources, world class pink salt and other many minerals in different regions which need further exploitation and development. The construction of new water dams in different regions are vital (for availability of cheap electricity), because of available barren and fertile lands and wastage of water as flood. Further the installation of more cement industries in different regions of Indus Basin especially in middle Indus (Sulaiman Range where gypsum, clays and limestones can be available via belt) can increase export to receive more foreign exchange and make local cement cheap for the sustainable development of Pakistan. 31 stratigraphic sequential sections at different sections of Indus basins are presented to know the variation and local stratigraphy. Further here three new titanosaur taxa are being described. Saraikimasoom is based on snout;Gspsaurus, (Maojandino), Nicksaurus and Khanazeem are based on cranial, vertebral and appendicular elements;Balochisaurus, Marisaurus, Pakisaurus, and 3 new genera and species Imrankhanhero zilefatmi, Qaikshaheen masoomniazi and Ikqaumishan smqureshi based on vertebral and appendicular elements;and Sulaimanisaurus and Khetranisaurus based on only caudal vertebrae. Although Pakistani Titanosaurians seem to be proliferated found from one horizon of Vitakri Formation just below the K-Pg boundary they have a wide range of diagnostic features and key elements among titanosaurs which can be used for comparison and phylogenetic analyses with broad updated character data set of titanosaurs.展开更多
基金financially supported by the National Natural Science Foundation of China (No. 51674069)the National Key R & D Program of China (No. 2017YFC0805100)
文摘For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al_2O_3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface.
文摘The separation process of non-metallic inclusions at the steel–slag interface was simulated by physical modeling. Three different kinds of particles(octahedral, plate-like, and spherical) and three different oils(kerosene, bean oil, and pump oil) were used to model inclusions and slags, respectively. The effects of inclusion geometry(shape and size) and slag properties(viscosity and interfacial tension) on the separation process were investigated. The results revealed that the variation of surface free energy and the viscosity of the slag are two significant factors affecting the separation process of inclusions at the steel–slag interface. The variation of surface free energy helped inclusions enter the slag phase, whereas the decrease of slag viscosity shortened the separation time. The deformation of the steel–slag interface could give rise to the resistance force, which would resist inclusions passing through the interface. A liquid film formed on the inclusion as it passed through the steel–slag interface, which might be related to the inclusion's shape.
文摘Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time largely affected non-metallic inclusions.With the reaction time increased from 30 min to 90 min in laboratory study,MgO-Al_2O_3 spinels were gradually changed into CaO-MgO-Al_2O_3 system inclusions surrounded by softer CaO-Al_2O_3 surface layers.By using high basicity slag which contained as much as 41%Al_2O_3 in the laboratory study,ratio of low melting temperature CaO-MgO-Al_2O_3 system inclusions was remarkably increased to above 80%.In the industrial experiment,during the secondary refining,the inclusions changed in order of 'Al_2O_3→MgO-Al_2O_3→CaO-MgO-Al_2O_3'.Through the LF and RH refining,most inclusions could be transferred to lower melting temperature CaO-Al_2O_3 and CaO-MgO-Al_2O_3 system inclusions.
基金Supported by Downhole Intelligent Measurement and Control Science and Technology Innovation Team of Southwest Petroleum University(Grant No.2018CXTD04)National Natural Science Foundation of China(Grant Nos.61701085,51974273)+1 种基金Chengdu Municipal international science and technology cooperation project of China(Grant Nos.2020-GH02-00016-HZ)2020 National Mountain Highway Engineering Technology Research Center Open Fund Project(Grant No.GSGZJ-2020-01).
文摘Buried pipelines are an essential component of the urban infrastructure of modern cities.Traditional buried pipes are mainly made of metal materials.With the development of material science and technology in recent years,non-metallic pipes,such as plastic pipes,ceramic pipes,and concrete pipes,are increasingly taking the place of pipes made from metal in various pipeline networks such as water supply,drainage,heat,industry,oil,and gas.The location technologies for the location of the buried metal pipeline have become mature,but detection and location technologies for the non-metallic pipelines are still developing.In this paper,current trends and future perspectives of detection and location of buried non-metallic pipelines are summarized.Initially,this paper reviews and analyzes electromagnetic induction technologies,electromagnetic wave technologies,and other physics-based technologies.It then focuses on acoustic detection and location technologies,and finally introduces emerging technologies.Then the technical characteristics of each detection and location method have been compared,with their strengths and weaknesses identified.The current trends and future perspectives of each buried non-metallic pipeline detection and location technology have also been defined.Finally,some suggestions for the future development of buried non-metallic pipeline detection and location technologies are provided.
基金Supported by Natural Science Foundation of China (No.81571819 No.81500766)the Natural Science Foundation of Zhejiang Province, China (No.LY14H120004)
文摘Dear Editor,I write to present one case report of a patient suffered the panophthalmitis caused by non-metallic foreign body with no etiologic agent and recovered quickly by phacoemulsification and vitrectomy with silicone oil tamponade.Ocular trauma remains a major cause of blindness, particularly in the working-age population.
文摘In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis extraction method with a settled coulometer. In the research,the extraction effects of non-metallic inclusions in different electrolysis systems were studied, and it was concluded that alkalescent 2% TEA non-aqueous electrolyte was applicable for extracting most of non-metallic inclusion particles in steel. And then, in order to ensure the microscopic characterization and statistical calculation of inclusion particles, some electrolysis parameters should be confirmed, such as the size of the sample, control of the electrolysis mass, electric current, etc. Furthermore, for preventing the disturbance of carbides and presenting clear three-dimensional appearance by microscopic characterization, magnetic separation was utilized to separate the inclusion particles from carbides, which was useful for getting more veracious types, particle sizes and chemical composition of inclusions. Moreover, through calculation of quantity and particle size of inclusions in continuous determinate fields, the total quantity per unit volume or area and the particle size distribution of inclusions could be acquired by conversion with electrolysis loss. Besides, the comparison between this method and traditional quantitative metallography was also discussed, and finally, a conclusion was drawn that both of them have respectively applications in characterizing inclusions.
基金the Banaras Hindu University,Varanasi,Uttar Pradesh(India),for providing a seed grant(Letter No.R/Dev/D/IoE/Equipment/Seed Grant-II/2022-23/52078)under the Institute of Eminence(IoE)Jyotsna Singh(Ref.No.210510120701),Subhash Singh(Ref.No.220510022095),and Purushottam Tiwari(Ref.No.210510406257)are grateful to the University Grants Commission(UGC)of the Ministry of Education,Government of India(New Delhi)for providing financial support to the present study+2 种基金the Copernicus Climate Change Service(C3S)team at the European Centre for Medium-Range Weather Forecasts(ECMWF)for providing ERA5 reanalysis data in the public domainreceived a seed grant from the Banaras Hindu University,Varanasi,Uttar Pradesh(India)(Letter No.R/Dev/D/IoE/Equipment/Seed Grant-II/2022-23/52078)under the Institute of Eminence(IoE)Jyotsna Singh(Ref.No.210510120701),Subhash Singh(Ref.No.220510022095),and Purushottam Tiwari(Ref.No.210510406257)received a fellowship from the University Grants Commission(UGC)of the Ministry of Education,Government of India(New Delhi)。
文摘Precipitable Water Vapor(PWV)constitutes a pivotal parameter within the domains of atmospheric science,and remote sensing due to its profound influence on Earth’s climate dynamics and weather patterns.It exerts a significant impact on atmospheric stability absorption and emission of radiation,thus engendering alterations in the Earth’s radiative equilibrium.As such,precise quantification of PWV holds the potential to enhance weather prognostication and fortify preparedness against severe meteorological phenomena.This study aimed to elucidate the spatial and temporal changes in seasonal and annual PWV across the Indus River Basin and its sub-basins using ERA5 reanalysis datasets.The present study used ERA5 PWV(entire atmospheric column),air temperature at 2 m(t2m)and 500 hPa(T_500hPa),evapotranspiration,and total cloud cover data from 1960 to 2021.Theil Sen slope estimator and Mann-Kendall test were used for trend analysis.Correlation and multiple regression methods were used to understand the association of PWV with other factors.The findings have unveiled the highest increase in mean PWV during the monsoon(0.40 mm/decade),followed by premonsoon(0.37 mm/decade),post-monsoon(0.27 mm/decade),and winter(0.19 mm/decade)throughout the study period.Additionally,the mean PWV exhibited the most pronounced positive trend in the sub-basin Lower Indus(LI),followed by Panjnad(P),Kabul(K),and Upper Indus(UI)across all seasons,except winter.Annual PWV has also risen in the Indus basin and its sub-basins over the last six decades.PWV exhibits a consistent upward trend up to an elevation of 3500 m within the basin which is most pronounced during the monsoon season,followed by the pre-monsoon.The escalating PWV within the basin is reasonably ascribed to increasing air temperatures,augmented evapotranspiration,and heightened cloud cover.These findings hold potential utility for pertinent authorities engaged in water resource management and planning.
文摘In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further.
文摘Non-metallic inclusions,especially the large ones,within P/M Ni-base superalloy have a major influence on fatigue characteristics,but are not directly measurable by routine inspection.In this paper,a method,automatic image analysis,is proposed for estimation of the content,size and amount of non-metallic inclusions in superalloy.The methodology for the practical application of this method is described and the factors affecting the precision of the estimation are discussed.In the experiment,the characteristics of the non-metallic inclusions in Ni-base P/M superalloy are analyzed.
基金Supported by the Innovative Research Group Project of China National Natural Science Foundation(51821092)Key Project of China National Natural Science Foundation(U1762214).
文摘Focusing on the extending length restriction of the completion screen pipe resistance running into ultra-short radius horizontal well,this paper proposed technology of hydraulic drive completion tubular string running into ultra-short radius horizontal well.Innovative hydraulic drive tools and string structure are designed,which are composed of guide tubing,hydraulic drive tubing and non-metallic completion screen pipe from inside to outside.A novel mechanical-hydraulic coupling model is established.Based on the wellbore structure of an ultra-short radius horizontal well for deep coalbed methane,the numerical calculations of force and hydraulic load on tubular strings were accomplished by the mechanical-hydraulic coupling model.The results show that the extending length of completion tubular string with the hydraulic drive is 17 times that of conventional completion technology under the same conditions.The multi-factor orthogonal design is adopted to analyze the numerical calculations,and the results show that the extending length of the completion tubular string is mainly affected by the completion tubular string structure and the friction coefficient between the non-metallic composite continuous screen pipe and the wellbore.Two series of hydraulic drive completion tubular string structures suitable for ultra-short radius horizontal wells under different conditions are optimized,with the extending limits of 381 m and 655 m,respectively.These researches will provide theoretical guidance for design and control of hydraulic drive non-metallic composite continuous completion screen pipe running into ultra-short radius horizontal wells.
文摘In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The largest size of inclusions in the casting and the thermodynamic possibility of TiN precipitation in steel were also calculated. The results show that sulfide inclusions are evenly distributed and the content is low. The amount of oxide inclusions in CIESC: 4Cr5MoSiV1 steel is close to the ESR steel and lower than that in the EAF steel, and there are some differences along radial direction. Nitride inclusions are fine and the diameter of the largest one is 3-1 mum. With the increase of the centrifugal machine's rotational speed, the ratio of round inclusions increases and the ratio of sharp inclusions decreases. According to the experiment and the calculation results, it is pointed out that the largest diameter of non-metallic inclusions in the CIESC 4Cr5MoSiV1 casting is only 6.6 mum, and [N%][Ti%] in 4Cr5MoSiV1 steel should be controlled less than 4.4x 10(-5) in order to further reduce the amount and size of TiN inclusions.
文摘Six different kinds of non-metallic or organic disinfectants were obtained in this research study including “Neutral Electrolyzed Water”, “M22” organic disinfectant solution, Superoxy Food Wash disinfectant, Hydrogen Peroxide, Clorox Germicidal Bleach and Clidox-S. The effectiveness of these disinfectants was studied against various subtypes of avian influenza virus (AIV). The virus-disinfectant mixtures were prepared in serial dilutions of each disinfectant with a constant virus titer and incubated at ambient temperature in different time intervals for virus inactivation. The virus inactivation results were determined by virus recovery in embryonating chicken eggs. Among the six different kinds of nonmetallic disinfectants obtained for this research project, Neutral Electrolyzed Water, “M22” solution, Clorox Germicidal Bleach and Clidox-S were effectively inactivated AIV with appropriate working dilutions and reaction times. Superoxy Food Wash disinfectant and Hydrogen Peroxide were found having limited effect on virus inactivation with extended exposure times of more than 2 hours. These research findings provide scientific data to poultry industry with guidelines to select and use non-metallic organic disinfectants for poultry flock sanitation and disinfection to effectively prevent and control of avian influenza outbreaks.
基金the Department of Science and Technology for the INSPIRE PhD fellowshipsupported by the FIG-100779 grant and IIT Roorkee Institute Fellowship to N Raithe Department of Science and Technology through INSPIRE fellowship(IF170907)scheme(grant No.7053-106-044-428)to A Jahan。
文摘The Indus river basin(IRB)is one of the most depleted water basins globally,having significant challenges for its water sector.Monitoring of stable isotope composition(δ^(18)O and δ^(2)H)across IRB is a critical aspect that can provide deeper insights for investigating complex hydrological processes.This work analyses the spatial pattern of the isotopic signature using a comprehensive compilation of available datasets of the Global Network of Isotopes in River(GNIR)and Global Network of Isotopes in Precipitation(GNIP),along with the previously published isotopic studies in the Indus basin.Additionally,this work provides a detailed comparison of the isotopic signature of the Upper Indus Basin(UIB),and Lower Indus Basin(LIB).The IRBs waterline was found to beδ^(2)H=7.89×δ^(18)O+13.51,which shows a close similarity with the Global Meteoric Water Line(GMWL),indicating the meteoric origin of the water with insignificant secondary evaporation prevailing across the basin.The Main Indus Channel(MIC)river water line(δ^(2)H=8.88×δ^(18)O+26.05)indicates a major contribution from the meteoric origin(precipitation/rain)of water with minimal effect of evaporation processes.The water line for UIB samples,(δ^(2)H=7.88×δ^(18)O+11.94)was found to be moderately higher in slope than LIB samples(δ^(2)H=7.17×δ^(18)O+7.16).However,the slopes of both UIB and LIB river water lines closely approached the slope of GMWL and were consistent with the slope of IRB water line,which indicates similarity in contribution of water sources.The higher slope and intercept in UIB suggest that meteoric water sources contributed to streamflow viz.from snow/glacier with insignificant evapotranspiration,which is also validated by the scarce vegetation cover in the UIB.However,the lower slope and intercept in LIB suggest stream water contribution from significantly evaporated groundwater and precipitation with a complete homogenization of discharge coming from the UIB.Results substantiate that distinct isotopic signatures found in different stretches of the IRB and along the MIC are caused by variations in basin characteristics,hydro-meteorological processes,water mixing,and minor influence of anthropogenic variables.
基金supported by the National Natural Science Foundation of China (52002412 and 22072186)the Natural Science Foundation of Guangdong Province (2021A1515010575)the Guangzhou Science and Technology Plan General Project (202102020862)。
文摘Developing high-performing non-noble transition metal catalysts for H_(2) evolution from chemical hydrogen storage materials is of great significance for the hydrogen economy system, yet challenging. Herein,we present for the first time that anomalous metastable hexagonal close-packed Ni nanoparticles induced by heteroatom N doping encapsulated in carbon(N-hcp-Ni/C) can exhibit admirable catalytic performance for ammonia borane(AB) dehydrogenation, prominently outperforming conventional fcc Ni counterpart with similar morphology and favorably presenting the state-of-the-art level.Comprehensive experimental and theoretical studies unravel that unusual hcp phase engineering of Ni together with N doping could induce charge redistribution and modulate electronic structure, thereby facilitating H_(2)O adsorption and expediting H_(2)O dissociation(rate-determining step). As a result, AB dehydrogenation can be substantially boosted with the assistance of N-hcp-Ni/C. Our proposed strategy highlights that unconventional crystal phase engineering coupled with non-metal heteroatom doping is a promising avenue to construct advanced transition metal catalysts for future renewable energy technologies.
基金the Banaras Hindu University,Varanasi,Uttar Pradesh(India),for providing a seed grant(Letter No.R/Dev/D/IoE/Equipment/SeedGrantII/2022-23/52078)under the Institute of Eminence(IoE)。
文摘Land surface temperature(LST)is a crucial parameter for understanding the Earth's surface energy balance,which provides insights into climate dynamics and local environmental conditions.Thus,the present study aims to evaluate the spatial and elevation-wise trends in the daytime,nighttime,and mean LST across the Indus River Basin(IRB)using MODIS 8-day product for the period between 2002 and 2022.The elevation,cloud cover,and land cover type data are used for explaining the emerging LST trends.The Theil slope estimator and MannKendall significance test were used for estimating the seasonal and annual LST trends.The findings show warming in mean daytime(0.020-0.024℃/yr)(except winter and post-monsoon),nighttime(0.013-0.049℃/yr),and mean(0.001-0.042℃/yr)LST in all the seasons(highest in monsoon).The annual mean nighttime LST(0.025℃/yr)is rising significantly faster than the mean daytime LST(0.0016℃/yr),showing the presence of a“nighttime warming effect”,which possibly increases human discomfort,particularly during the warm pre-monsoon and humid monsoon season.Elevation-dependent warming(EDW)is predominant in mean daytime LST in two elevation zones,namely(i)0-3 km and(ii)above 4 km,in all seasons,except in post-monsoon.In contrast,EDW in mean nighttime LST is observed up to 3 km and above 6 km in the basin in all the seasons,excluding post-monsoon.The warming trend in LST may be attributed to rising atmospheric moisture,cloud cover,declining snow cover,and changes in land cover to non-vegetated land.However,further investigations will involve exploring the underlying factors contributing to the observed anomalies in nighttime LST,considering variables such as regional energy balance and atmospheric stability.This research contributes to an understanding of the thermal dynamics in the mountain basin,aiding in climate studies,land management,and the development of effective adaptation strategies in the IRB.
基金the National Mission on Himalayan Studies(NMHS),Ministry of Environment,Forest and Climate Change(MoEFCC)for the financial support under the research project number(GBPNI/NMHS-2019-20/MG)。
文摘Climate change differentially influences the frozen ground,a major dynamic component of the cryosphere,on a local and regional scale.Under the warming climate with pronounced effects reported at higher altitudes,the characterization of the frozen ground is very important in the Upper Indus Basin(UIB),an important and critical region with respect to climate and hydro-glaciological dynamics.In this study,the efficiency and reliability of the surface frost number model are assessed in delineating the spatial extent of different classes of frozen ground in the region.The daily MODIS land surface temperature(LST)with ground surface temperature(GST)and surface geomorphological expressions as ground validation datasets are used jointly in efficiently determining the extent of different classes of frozen ground(continuous and discontinuous permafrost and seasonal frost).The LST and GST resonate with each other in the annual cycle of temperature variation,however,with mean annual LST exhibiting an offset(cold bias)of 5 to 7℃relative to mean GST.This study shows that the highest permafrost extent is observed in areas where the lowest thinning rates of glacier ice are reported and vice versa.The surface frost number model categorizes an area of 38%±3%and 15%±3%in the UIB as permafrost and seasonal frost,respectively.Based on the altitude model,the lower limit of alpine permafrost is approximated at a mean altitude of 4919±590 m a.s.l.in the UIB.The present study acts as preliminary work in the data sparse and inaccessible regions of the UIB in characterizing the frozen and unfrozen ground and may act as a promising input data source in glaciohydro-meteorological models for the Himalaya and Karakoram.In addition,the study also underlines the consideration of this derelict cryospheric climatic variable in defining and accounting for the sustainable development of socio-economic systems through its intricate ramification on agricultural activity,landscape stability and infrastructure.
文摘The expansion parts and components of non-metallic in devices have become a fait accompli. In the case parts, components of non-metallic are used in atmospheres explosive and may be a potential source of ignition [1]. Ignition hazards due to static electricity from the charged non-conductive non-metallic materials are well known [2]. The prevalence protection metal parts and components of anti-corrosion exist in any device equipped with a metal casing. Inherent risks associated services are caused by static electricity. Electrostatic phenomena arise in many situations, in a variety of environments and industries. The occurrence of charge static in many cases unexpected is unwanted and requires the use of expensive preventive measures. Brush discharge and propagating brush discharge (e.g. composite coating about non-conductive electrostatic properties of an isolated base conductive) create explosion hazard in underground endangered by firedamp and/or coal dust [3].
文摘The Sohnari Member of the Early Eocene Laki Formation is massively deposited in the Southern Indus Basin of Pakistan and is considered a potential source rock to generate hydrocarbons.However,the detailed paleoclimatic,paleoweathering,and depositional conditions of the Sohnari Member have not been studied earlier.This research mainly discusses the detailed mineralogical(bulk and clay)and elemental geochemistry of the Laki Formation from two outcrop sections(Jhimpir and Lakhra)in the Southern Indus Basin,Pakistan.The bulk minerals,including quartz(low),hematite,calcite,halite,gypsum,and clay minerals such as kaolinite,chlorite,smectite and illite have been discussed here.These results demonstrate the paleo-environment of studied area was arid with enhanced saline and weak to strong oxidizing depositional conditions.The chemical index of alteration(CIA)values in Jhimpir and Lakhra sections are in the ranges of 41.30-97.93 and 22.30-96.19,respectively,indicating that the Sohnari sediments experienced weak to intense chemical weathering in the source area.The interpretation of the A-CN-K ternary diagram is consistent with the clay mineral contents in the studied sediments,which is characterized by the predominance of kaolinite,gibbsite and chlorite,demonstrating the weak to strong weathering state under warm and humid climatic conditions.The chemical indices such as Sr/Ba,δU,V/Cr,Ni/Co,and Cu/Zn,U/Th and Ba/Ga show that Sohnari rocks of Early Eocene Laki Formation underwent strong evaporation,oxic water column with warm to humid and minor contact of cold climatic conditions.Based on our present data,it can be concluded that the sediments of Sohnari Member of Laki Formation from Jhimpir and Lakhra areas of Southern Indus Basin in Pakistan are related to Indio-Eurasian collision and came from the Indian shield rocks that were deposited in a brackish water body with a minor contact of the freshwater oxidizing paleo-environment depositional conditions.
文摘Indus basin hosts many significant mineral deposits like gypsum and cement raw materials, gemstones, iron, coal, marble, dimension and construction stones, petroleum and water resources, world class pink salt and other many minerals in different regions which need further exploitation and development. The construction of new water dams in different regions are vital (for availability of cheap electricity), because of available barren and fertile lands and wastage of water as flood. Further the installation of more cement industries in different regions of Indus Basin especially in middle Indus (Sulaiman Range where gypsum, clays and limestones can be available via belt) can increase export to receive more foreign exchange and make local cement cheap for the sustainable development of Pakistan. 31 stratigraphic sequential sections at different sections of Indus basins are presented to know the variation and local stratigraphy. Further here three new titanosaur taxa are being described. Saraikimasoom is based on snout;Gspsaurus, (Maojandino), Nicksaurus and Khanazeem are based on cranial, vertebral and appendicular elements;Balochisaurus, Marisaurus, Pakisaurus, and 3 new genera and species Imrankhanhero zilefatmi, Qaikshaheen masoomniazi and Ikqaumishan smqureshi based on vertebral and appendicular elements;and Sulaimanisaurus and Khetranisaurus based on only caudal vertebrae. Although Pakistani Titanosaurians seem to be proliferated found from one horizon of Vitakri Formation just below the K-Pg boundary they have a wide range of diagnostic features and key elements among titanosaurs which can be used for comparison and phylogenetic analyses with broad updated character data set of titanosaurs.