Acoustic location echo signal extraction of buried non-metallic pipelines based on EMD and wavelet threshold joint denoising

In the acoustic detection process of buried non-metallic pipelines,the echo signal is often interfered by a large amount of noise,which makes it extremely difficult to effectively extract useful signals.An denoising algorithm based on empirical mode decomposition(EMD)and wavelet thresholding was proposed.This method fully considered the nonlinear and non-stationary characteristics of the echo signal,making the denoising effect more significant.Its feasibility and effectiveness were verified through numerical simulation.When the input SNR(SNRin)is between-10 dB and 10 dB,the output SNR(SNRout)of the combined denoising algorithm increases by 12.0%-34.1%compared to the wavelet thresholding method and by 19.60%-56.8%compared to the EMD denoising method.Additionally,the RMSE of the combined denoising algorithm decreases by 18.1%-48.0%compared to the wavelet thresholding method and by 22.1%-48.8%compared to the EMD denoising method.These results indicated that this joint denoising algorithm could not only effectively reduce noise interference,but also significantly improve the positioning accuracy of acoustic detection.The research results could provide technical support for denoising the echo signals of buried non-metallic pipelines,which was conducive to improving the acoustic detection and positioning accuracy of underground non-metallic pipelines.

Effect of continuous casting speed on mold surface flow and the related near-surface distribution of non-metallic inclusions

For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al_2O_3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface.

Current Trends and Perspectives of Detection and Location for Buried Non-Metallic Pipelines

Buried pipelines are an essential component of the urban infrastructure of modern cities.Traditional buried pipes are mainly made of metal materials.With the development of material science and technology in recent years,non-metallic pipes,such as plastic pipes,ceramic pipes,and concrete pipes,are increasingly taking the place of pipes made from metal in various pipeline networks such as water supply,drainage,heat,industry,oil,and gas.The location technologies for the location of the buried metal pipeline have become mature,but detection and location technologies for the non-metallic pipelines are still developing.In this paper,current trends and future perspectives of detection and location of buried non-metallic pipelines are summarized.Initially,this paper reviews and analyzes electromagnetic induction technologies,electromagnetic wave technologies,and other physics-based technologies.It then focuses on acoustic detection and location technologies,and finally introduces emerging technologies.Then the technical characteristics of each detection and location method have been compared,with their strengths and weaknesses identified.The current trends and future perspectives of each buried non-metallic pipeline detection and location technology have also been defined.Finally,some suggestions for the future development of buried non-metallic pipeline detection and location technologies are provided.

Study on non-metallic inclusions in Al killed high strength alloy steel refined by high basicity and high Al_2O_3 content slag

Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time largely affected non-metallic inclusions.With the reaction time increased from 30 min to 90 min in laboratory study,MgO-Al_2O_3 spinels were gradually changed into CaO-MgO-Al_2O_3 system inclusions surrounded by softer CaO-Al_2O_3 surface layers.By using high basicity slag which contained as much as 41%Al_2O_3 in the laboratory study,ratio of low melting temperature CaO-MgO-Al_2O_3 system inclusions was remarkably increased to above 80%.In the industrial experiment,during the secondary refining,the inclusions changed in order of 'Al_2O_3→MgO-Al_2O_3→CaO-MgO-Al_2O_3'.Through the LF and RH refining,most inclusions could be transferred to lower melting temperature CaO-Al_2O_3 and CaO-MgO-Al_2O_3 system inclusions.

A presumed iridocyclitis developed to panophthalmitis caused by a non-metallic intraocular foreign body

Dear Editor,I write to present one case report of a patient suffered the panophthalmitis caused by non-metallic foreign body with no etiologic agent and recovered quickly by phacoemulsification and vitrectomy with silicone oil tamponade.Ocular trauma remains a major cause of blindness, particularly in the working-age population.

Three-dimensional analysis technology for accurately characterizing non-metallic inclusion particles in steel

In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis extraction method with a settled coulometer. In the research,the extraction effects of non-metallic inclusions in different electrolysis systems were studied, and it was concluded that alkalescent 2% TEA non-aqueous electrolyte was applicable for extracting most of non-metallic inclusion particles in steel. And then, in order to ensure the microscopic characterization and statistical calculation of inclusion particles, some electrolysis parameters should be confirmed, such as the size of the sample, control of the electrolysis mass, electric current, etc. Furthermore, for preventing the disturbance of carbides and presenting clear three-dimensional appearance by microscopic characterization, magnetic separation was utilized to separate the inclusion particles from carbides, which was useful for getting more veracious types, particle sizes and chemical composition of inclusions. Moreover, through calculation of quantity and particle size of inclusions in continuous determinate fields, the total quantity per unit volume or area and the particle size distribution of inclusions could be acquired by conversion with electrolysis loss. Besides, the comparison between this method and traditional quantitative metallography was also discussed, and finally, a conclusion was drawn that both of them have respectively applications in characterizing inclusions.

Behavior of Non-metallic Inclusions in Centrifugal Induction Electroslag Castings

In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The largest size of inclusions in the casting and the thermodynamic possibility of TiN precipitation in steel were also calculated. The results show that sulfide inclusions are evenly distributed and the content is low. The amount of oxide inclusions in CIESC: 4Cr5MoSiV1 steel is close to the ESR steel and lower than that in the EAF steel, and there are some differences along radial direction. Nitride inclusions are fine and the diameter of the largest one is 3-1 mum. With the increase of the centrifugal machine's rotational speed, the ratio of round inclusions increases and the ratio of sharp inclusions decreases. According to the experiment and the calculation results, it is pointed out that the largest diameter of non-metallic inclusions in the CIESC 4Cr5MoSiV1 casting is only 6.6 mum, and [N%][Ti%] in 4Cr5MoSiV1 steel should be controlled less than 4.4x 10(-5) in order to further reduce the amount and size of TiN inclusions.

Modelling and Dynamic Characteristics for a Non-metal Pressurized Reservoir with Variable Volume

With the increasing demand to reduce emissions and save energy,hydraulic reservoirs require new architecture to optimize their weight,space,and volume.Conventional open reservoirs are large,heavy,and easily polluted,and threaten the operation of hydraulic systems.A closed reservoir provides the advantages of small volume and light weight,compared to open reservoirs.In this study,a non-metallic pressure reservoir with variable volume is designed and manufactured for closed-circuit hydraulic systems.The reservoir housing is made of rubber,and the Mooney-Rivlin model is chosen based on the rubber strain properties.The FEA simulation for the reservoir is performed using ANSYS Workbench to obtain the structural stiffness.The major contribution is the establishment of mathematical models for this reservoir,including the volume equation changing with height,flow equation,and force balance equation,to explore the output characteristics of this reservoir.Based on these results,simulation models were built to analyze the output characteristics of the reservoir.Moreover,the test rig of a conventional hydraulic system was transformed into a closed-circuit asymmetric hydraulic system for the reservoir,and preliminary verification experiments were conducted on it.The results demonstrate that the designed reservoir can absorb and discharge oil and supercharge pump inlet to benefit system operation.The changes in the volume and pressure with displacements under different volume ratios and frequencies were obtained,which verified the accuracy of the mathematical models.Owing to its lightweight design and small volume,the reservoir can replace conventional open reservoirs,and this lays a foundation for future theoretical research on this reservoir.

Non-metallic Inclusions in Continuously Cast Aluminum Killed Steels

In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further.

Evaluation of Characteristics of Non-Metallic Inclusions in P/M Ni-Base Superalloy by Automatic Image Analysis

Non-metallic inclusions,especially the large ones,within P/M Ni-base superalloy have a major influence on fatigue characteristics,but are not directly measurable by routine inspection.In this paper,a method,automatic image analysis,is proposed for estimation of the content,size and amount of non-metallic inclusions in superalloy.The methodology for the practical application of this method is described and the factors affecting the precision of the estimation are discussed.In the experiment,the characteristics of the non-metallic inclusions in Ni-base P/M superalloy are analyzed.

The extending length calculation of hydraulic drive non-metallic completion screen pipe running into ultra-short radius horizontal well

Focusing on the extending length restriction of the completion screen pipe resistance running into ultra-short radius horizontal well,this paper proposed technology of hydraulic drive completion tubular string running into ultra-short radius horizontal well.Innovative hydraulic drive tools and string structure are designed,which are composed of guide tubing,hydraulic drive tubing and non-metallic completion screen pipe from inside to outside.A novel mechanical-hydraulic coupling model is established.Based on the wellbore structure of an ultra-short radius horizontal well for deep coalbed methane,the numerical calculations of force and hydraulic load on tubular strings were accomplished by the mechanical-hydraulic coupling model.The results show that the extending length of completion tubular string with the hydraulic drive is 17 times that of conventional completion technology under the same conditions.The multi-factor orthogonal design is adopted to analyze the numerical calculations,and the results show that the extending length of the completion tubular string is mainly affected by the completion tubular string structure and the friction coefficient between the non-metallic composite continuous screen pipe and the wellbore.Two series of hydraulic drive completion tubular string structures suitable for ultra-short radius horizontal wells under different conditions are optimized,with the extending limits of 381 m and 655 m,respectively.These researches will provide theoretical guidance for design and control of hydraulic drive non-metallic composite continuous completion screen pipe running into ultra-short radius horizontal wells.

Studies of non-metallic organic disinfectants on inactivation of avian influenza viruses

Six different kinds of non-metallic or organic disinfectants were obtained in this research study including “Neutral Electrolyzed Water”, “M22” organic disinfectant solution, Superoxy Food Wash disinfectant, Hydrogen Peroxide, Clorox Germicidal Bleach and Clidox-S. The effectiveness of these disinfectants was studied against various subtypes of avian influenza virus (AIV). The virus-disinfectant mixtures were prepared in serial dilutions of each disinfectant with a constant virus titer and incubated at ambient temperature in different time intervals for virus inactivation. The virus inactivation results were determined by virus recovery in embryonating chicken eggs. Among the six different kinds of nonmetallic disinfectants obtained for this research project, Neutral Electrolyzed Water, “M22” solution, Clorox Germicidal Bleach and Clidox-S were effectively inactivated AIV with appropriate working dilutions and reaction times. Superoxy Food Wash disinfectant and Hydrogen Peroxide were found having limited effect on virus inactivation with extended exposure times of more than 2 hours. These research findings provide scientific data to poultry industry with guidelines to select and use non-metallic organic disinfectants for poultry flock sanitation and disinfection to effectively prevent and control of avian influenza outbreaks.

Charging of Materials Non-Metallic Used in Underground Mines Endangered by Firedamp and/or Coal Dust

The expansion parts and components of non-metallic in devices have become a fait accompli. In the case parts, components of non-metallic are used in atmospheres explosive and may be a potential source of ignition [1]. Ignition hazards due to static electricity from the charged non-conductive non-metallic materials are well known [2]. The prevalence protection metal parts and components of anti-corrosion exist in any device equipped with a metal casing. Inherent risks associated services are caused by static electricity. Electrostatic phenomena arise in many situations, in a variety of environments and industries. The occurrence of charge static in many cases unexpected is unwanted and requires the use of expensive preventive measures. Brush discharge and propagating brush discharge (e.g. composite coating about non-conductive electrostatic properties of an isolated base conductive) create explosion hazard in underground endangered by firedamp and/or coal dust [3].

杂交苜蓿(Medicago varia Martyn)根系特性的研究

杂交苜蓿是野苜蓿 (M .falcata)和紫苜蓿 (M .sativaL .)的杂交后代 ,兼具亲本的许多优良性状 ,适于广泛栽培。对其在根系特性上所表现出的优势进行研究发现 :根颈处的劈裂将植株分为母株与子株 ,实现营养繁殖 ;位于茎基部的当年芽数量明显大于亲本 ,是地上生物量增长的基础 ;明显的缩根现象有利于茎基部和根颈顶部芽的产生和越冬 ;明显优于亲本的侧根与不定根 。

Recent advances in non-metal doped titania for solar-driven photocatalytic/photoelectrochemical water-splitting

Photocatalytic (PC) / Photoelectrochemical (PEC) water splitting under solar light irradiation is considered as a prospective technique to support the sustainable and renewable H_(2) economy and to reach the ultime goal of carbon neutral. TiO_(2) based photocatalysts with high chemical stability and excellent photocatalytic properties have great potential for solar-to-H_(2) conversion. To conquer the challenges of the large band-gap and rapid recombination of photo generated electron-holepairs in TiO_(2), non-metal doping turns out to be economic, facile, and effective on boosting the visible light activity. The localized defect states such as oxygen vacancy and Ti^(3+) generated by non-metal doping are located in the band-gap of TiO_(2), which result in the reduction of band-gap, thus a red-shift of the absorption edge. The hetero doping atoms such as B^(3+), I^(7+), S^(4+)/S^(6+), P^(5+) can also act as electron donors or trap sites which facilitate the charge carrier separation and suppress the recombination of electron-hole pairs. In this comprehensive review, we present the most recent advances on non-metal doped TiO_(2) photocatalysts in terms of fundamental aspects, origin of visible light activity and the PC / PEC behaviours for water splitting. In particular, the characteristics of different non-metal elements (N, C, B, S, P, Halogens) as dopants are discussed in details focusing on the synthesis approaches, characterization as well as the efficiency of PC and PEC water splitting. The present review aims at guiding the readers who want quick access to helpful information about how to efficiently improve the performance of photocatalysts by simple doping strategies and could stimulate new intuitive into the new doping strategies.

Anomalous metastable hcp Ni nanocatalyst induced by non-metal N doping enables promoted ammonia borane dehydrogenation

Developing high-performing non-noble transition metal catalysts for H_(2) evolution from chemical hydrogen storage materials is of great significance for the hydrogen economy system, yet challenging. Herein,we present for the first time that anomalous metastable hexagonal close-packed Ni nanoparticles induced by heteroatom N doping encapsulated in carbon(N-hcp-Ni/C) can exhibit admirable catalytic performance for ammonia borane(AB) dehydrogenation, prominently outperforming conventional fcc Ni counterpart with similar morphology and favorably presenting the state-of-the-art level.Comprehensive experimental and theoretical studies unravel that unusual hcp phase engineering of Ni together with N doping could induce charge redistribution and modulate electronic structure, thereby facilitating H_(2)O adsorption and expediting H_(2)O dissociation(rate-determining step). As a result, AB dehydrogenation can be substantially boosted with the assistance of N-hcp-Ni/C. Our proposed strategy highlights that unconventional crystal phase engineering coupled with non-metal heteroatom doping is a promising avenue to construct advanced transition metal catalysts for future renewable energy technologies.

Interannual variations of the air-sea carbon dioxide exchange in the different regions of the Pacific Ocean

Interannual variations of the air-sea CO2 exchange from 1965 to 2000 in the Pacific Ocean are studied with a Pacific Ocean model. Two numerical experiments are performed, including the control run that is forced by climatological monthly mean physical data and the climate-change run that is forced by interannually varying monthly mean physical data. Climatological monthly winds are used in both runs to calculate the coefficient of air-sea CO2 exchange. The analysis through the differences between the two runs shows that in the tropical Pacific the variation of export production induced by interannual variations of the physical fields is negatively correlated with that of the air-sea CO2 flux, while there is no correlation or a weak positive correlation in the subtropical North and South Pacific. It indicates that the variation of the physical fields can modulate the variation of the air-sea CO2 flux in converse ways in the tropical Pacific by changing the direct transport and biochemical process. Under the interannually varying monthly mean forcing, the simulated EOF 1 of the air-sea CO2 flux is basically consistent with that of sea surface temperature （SST） in the tropical Pacific, but contrary in the two subtropical Pacific Ocean. The correlation coefficient between the regionally integrated air-sea CO2 flux and area-mean SST shows that when the air-sea CO2 flux lags SST by about 5 months, the positive coefficient in the three regions is largest, indicating that in the tropical Pacific or on the longer time scale in the three regions, physical processes control the fiux-SST relationship.

Enhancing visible-light photocatalytic activity of α-Bi_2O_3 via non-metal N and S doping

In recent years, some important research indicated that the visible-light activity of photocatalysts could be enhanced via incorporating p-block non-metal elements into the lattice. In this paper, we investigated the electronic structures of pure and different non-metal （C, N, S, F, Cl, and Br） doped α-Bi2O3 using first-principles calculations based on the density functional theory. The band structures, the electronic densities of states, and the effective masses of electrons and holes for doped α-Bi2O3 were obtained and analyzed. The N and S dopings narrowed the band gap and reduced the effective mass of the carriers, which are beneficial for the photocatalytic performance. The theoretical predication was further confirmed by the experimental results.

Plants regeneration from protoplast and their genetic variation in foxtail millet

Compact calli derived from immature spikelet of a foxtail millet variety—Jigu 11cann’t be directly used for protoplast isolation because of its firm physical structure,and must beloosened with subculturing in M1,M2 and M3 media successively and altering these media compo-sitions.The loosened calli can be selected from the regulation and used for protoplast isolationsuccessfully.Rate of protoplast division in KM8P medium was 12.3—33.5%.Calli derivedthrough protoplast division are loose and cann’t be used directly for plan regeneration because ofits soft physical structure.When they were subcultured in N6—1,N6—2,N6—3 and N6—4 media,in which the media compositions were changed,the compact calli were obtained and 129 plantletswere regenerated from them.101 plants,which grew to maturity after transplanting the plantletsinto field,exhibited sterility in some degree.Most of the subsequent lines derived from the regen-erated plants were sterile and only two lines could get normal reproduction.

Nonlocal Lie-Backlund Symmetries and Olver Symmetries of the Variable Coefficient KdV and MKdV Equations

In this paper,three sets of higher order nonlocal Olver symmetriesare reobtained from a special nonlocal Lie-Backlund symmetry ofthe variable coefficient KdV and MKdV eguations.The soliton solutionof these models can be also obtained from the The finite Lie-Backlundtransformations.