Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natura...Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natural rock.Extrusion free forming(EFF)is a 3D printing technique that uses clay as the printing material and cures the specimens through high-temperature sintering.In this study,we attempted to use the EFF technology to fabricate artificial rock specimens.The results show the physico-mechanical properties of the specimens are significantly affected by the sintering temperature,while the nozzle diameter and layer thickness also have a certain impact.The specimens are primarily composed of SiO_(2),with mineral compositions similar to that of natural rocks.The density,uniaxial compressive strength(UCS),elastic modulus,and tensile strength of the printed specimens fall in the range of 1.65–2.54 g/cm3,16.46–50.49 MPa,2.17–13.35 GPa,and 0.82–17.18 MPa,respectively.It is capable of simulating different types of rocks,especially mudstone,sandstone,limestone,and gneiss.However,the simulation of hard rocks with UCS exceeding 50 MPa still requires validation.展开更多
A non contact three dimensional measurement method is presented in this paper.This system consists of a laser triangulation probe,a probe head and a coordinate measuring machine (CMM).The measurement principle of th...A non contact three dimensional measurement method is presented in this paper.This system consists of a laser triangulation probe,a probe head and a coordinate measuring machine (CMM).The measurement principle of the system is discussed,and a system calibration method employing a reference ball is proposed.The geometric model involving four frames is established to calculate the data points based on the reading of the laser probe and position information from the CMM.A measuring experiment for gesso free form surface using this system is carried out.展开更多
A new two-eigenfunctions theory, using the amplitude deflection and the generalized curvature as two fundamental eigenfunctions, is proposed for the free vibration solutions of a rectangular Mindlin plate. The three c...A new two-eigenfunctions theory, using the amplitude deflection and the generalized curvature as two fundamental eigenfunctions, is proposed for the free vibration solutions of a rectangular Mindlin plate. The three classical eigenvalue differential equations of a Mindlin plate are reformulated to arrive at two new eigenvalue differential equations for the proposed theory. The closed form eigensolutions, which are solved from the two differential equations by means of the method of separation of variables are identical with those via Kirchhoff plate theory for thin plate, and can be employed to predict frequencies for any combinations of simply supported and clamped edge conditions. The free edges can also be dealt with if the other pair of opposite edges are simply supported. Some of the solutions were not available before. The frequency parameters agree closely with the available ones through pb-2 Rayleigh-Ritz method for different aspect ratios and relative thickness of plate.展开更多
This article presents closed-form solutions for the frequency analysis of rectangular functionally graded material (FGM) thin plates subjected to initially in-plane loads and with an elastic foundation. Based on class...This article presents closed-form solutions for the frequency analysis of rectangular functionally graded material (FGM) thin plates subjected to initially in-plane loads and with an elastic foundation. Based on classical thin plate theory, the governing differential equations are derived using Hamilton's principle. A neutral surface is used to eliminate stretching-bending coupling in FGM plates on the basis of the assumption of constant Poisson's ratio. The resulting governing equation of FGM thin plates has the same form as homogeneous thin plates. The separation-of-variables method is adopted to obtain solutions for the free vibration problems of rectangular FGM thin plates with separable boundary conditions, including, for example, clamped plates. The obtained normal modes and frequencies are in elegant closed forms, and present formulations and solutions are validated by comparing present results with those in the literature and finite element method results obtained by the authors. A parameter study reveals the effects of the power law index n and aspect ratio a/b on frequencies.展开更多
Metal forming plays an important role in manufacturing industry and is widely applied in industries.The tradi- tional finite element method(FEM)numerical simulation is commonly used to predict metal forming process.Co...Metal forming plays an important role in manufacturing industry and is widely applied in industries.The tradi- tional finite element method(FEM)numerical simulation is commonly used to predict metal forming process.Conventional finite element analysis of metal forming processes often breaks down due to severe mesh distortion,therefore time-consuming remeshing is necessary.Meshfree methods have been developed since 1977 and can avoid this problem.This new generation of computational methods reduces time-consuming model generation and refinement effort,and its shape function has higher order connectivity than FEM’s.In this paper the velocity shape functions are developed from a reproducing kernel approximation that satisfies consistency conditions and is used to analyze metal tension rigid viscoplastic deforming and Magnesium Alloy(MB 15)sheet superplastic ten- sion forming.A meshfree method metal forming modeling program is set up,the partition of unity method is used to compute the integrations in weak form equations and penalty method is used to impose the essential boundary condition exactly.Metal forming examples,such as sheet metal superplastic tension forming and metal rigid viscoplastic tension forming,are analyzed to demon- strate the performance of mesh free method.展开更多
Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for ...Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for the verification of free-form surface profile are available, the profile parameters of free-form surface are proposed by referring to ISO standards regarding form tolerances and considering its complexity and non-rotational symmetry. Non-uniform rational basis spline（NURBS） for describing free-form surface is formulated. Crucial issues in surface inspection and profile error verification are localization between the design coordinate system（DCS） and measurement coordinate system（MCS） for searching the closest points on the design model corresponding to measured points. A quasi particle swarm optimization（QPSO） is proposed to search the transformation parameters to implement localization between DCS and MCS. Surface subdivide method which does the searching in a recursively reduced range of the parameters u and v of the NURBS design model is developed to find the closest points. In order to verify the effectiveness of the proposed methods, the design model is generated by NURBS and the measurement data of simulation example are generated by transforming the design model to arbitrary position and orientation, and the parts are machined based on the design model and are measured on CMM. The profile errors of simulation example and actual parts are calculated by the proposed method. The results verify that the evaluation precision of freeform surface profile error by the proposed method is higher 10%-22% than that by CMM software. The proposed method deals with the hard problem that it has a lower precision in profile error evaluation of free-form surface.展开更多
The direct separation of variables is used to obtain the closed-form solutions for the free vibrations of rectangular Mindlin plates. Three different characteristic equations are derived by using three different metho...The direct separation of variables is used to obtain the closed-form solutions for the free vibrations of rectangular Mindlin plates. Three different characteristic equations are derived by using three different methods. It is found that the deflection can be expressed by means of the four characteristic roots and the two rotations should be expressed by all the six characteristic roots,which is the particularity of Mindlin plate theory. And the closed-form solutions,which satisfy two of the three governing equations and all boundary conditions and are accurate for rectangular plates with moderate thickness,are derived for any combinations of simply supported and clamped edges. The free edges can also be dealt with if the other pair of opposite edges is simply supported. The present results agree well with results published previously by other methods for different aspect ratios and relative thickness.展开更多
With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu c...With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu ctive materials away and polishes work-piece of free-form surface. The study o f the contact force between the end of polishing tool and the surface of work-p iece is the key for the compliant EDM to study its cutting mechanism and to make better use of it. This paper makes a model for the contact force and verifies i t by experiments and simulation based on the theory of elastic body kinetics and dynamic stress concentration. The research work shows that this contact force i s caused by both the electrical impulsion of EDM and the mechanical force of ult rasonic vibration, the discharge frequency of compliant EDM has a much more clos er connection with the vibration frequency of polishing tool rather than the fre quency of ultrasonic vibration.展开更多
基金financially supported by the Beijing Natural Science Foundation for Young Scientists(Grant No.8214052)the Talent Fund of Beijing Jiaotong University(Grant No.2021RC226)the State Key Laboratory for GeoMechanics and Deep Underground Engineering,China University of Mining and Technology(Grant No.SKLGDUEK2115).
文摘Three-dimensional(3D)printing technology has been widely used to create artificial rock samples in rock mechanics.While 3D printing can create complex fractures,the material still lacks sufficient similarity to natural rock.Extrusion free forming(EFF)is a 3D printing technique that uses clay as the printing material and cures the specimens through high-temperature sintering.In this study,we attempted to use the EFF technology to fabricate artificial rock specimens.The results show the physico-mechanical properties of the specimens are significantly affected by the sintering temperature,while the nozzle diameter and layer thickness also have a certain impact.The specimens are primarily composed of SiO_(2),with mineral compositions similar to that of natural rocks.The density,uniaxial compressive strength(UCS),elastic modulus,and tensile strength of the printed specimens fall in the range of 1.65–2.54 g/cm3,16.46–50.49 MPa,2.17–13.35 GPa,and 0.82–17.18 MPa,respectively.It is capable of simulating different types of rocks,especially mudstone,sandstone,limestone,and gneiss.However,the simulation of hard rocks with UCS exceeding 50 MPa still requires validation.
基金Supported by"863"High Technology Development Comittee ofChina (No."863"- 51 1 - 942 - 0 2 4 ) National Natural Science Foun-dation of China (No.50 0 750 64)
文摘A non contact three dimensional measurement method is presented in this paper.This system consists of a laser triangulation probe,a probe head and a coordinate measuring machine (CMM).The measurement principle of the system is discussed,and a system calibration method employing a reference ball is proposed.The geometric model involving four frames is established to calculate the data points based on the reading of the laser probe and position information from the CMM.A measuring experiment for gesso free form surface using this system is carried out.
基金supported by the National Natural Science Foundation of China (10772014)
文摘A new two-eigenfunctions theory, using the amplitude deflection and the generalized curvature as two fundamental eigenfunctions, is proposed for the free vibration solutions of a rectangular Mindlin plate. The three classical eigenvalue differential equations of a Mindlin plate are reformulated to arrive at two new eigenvalue differential equations for the proposed theory. The closed form eigensolutions, which are solved from the two differential equations by means of the method of separation of variables are identical with those via Kirchhoff plate theory for thin plate, and can be employed to predict frequencies for any combinations of simply supported and clamped edge conditions. The free edges can also be dealt with if the other pair of opposite edges are simply supported. Some of the solutions were not available before. The frequency parameters agree closely with the available ones through pb-2 Rayleigh-Ritz method for different aspect ratios and relative thickness of plate.
基金supported by the National Natural Science Foundation of China (Grants 11172028, 1372021)Research Fund for the Doctoral Program of Higher Education of China (Grant 20131102110039)the Innovation Foundation of Beihang University for PhD graduates
文摘This article presents closed-form solutions for the frequency analysis of rectangular functionally graded material (FGM) thin plates subjected to initially in-plane loads and with an elastic foundation. Based on classical thin plate theory, the governing differential equations are derived using Hamilton's principle. A neutral surface is used to eliminate stretching-bending coupling in FGM plates on the basis of the assumption of constant Poisson's ratio. The resulting governing equation of FGM thin plates has the same form as homogeneous thin plates. The separation-of-variables method is adopted to obtain solutions for the free vibration problems of rectangular FGM thin plates with separable boundary conditions, including, for example, clamped plates. The obtained normal modes and frequencies are in elegant closed forms, and present formulations and solutions are validated by comparing present results with those in the literature and finite element method results obtained by the authors. A parameter study reveals the effects of the power law index n and aspect ratio a/b on frequencies.
文摘Metal forming plays an important role in manufacturing industry and is widely applied in industries.The tradi- tional finite element method(FEM)numerical simulation is commonly used to predict metal forming process.Conventional finite element analysis of metal forming processes often breaks down due to severe mesh distortion,therefore time-consuming remeshing is necessary.Meshfree methods have been developed since 1977 and can avoid this problem.This new generation of computational methods reduces time-consuming model generation and refinement effort,and its shape function has higher order connectivity than FEM’s.In this paper the velocity shape functions are developed from a reproducing kernel approximation that satisfies consistency conditions and is used to analyze metal tension rigid viscoplastic deforming and Magnesium Alloy(MB 15)sheet superplastic ten- sion forming.A meshfree method metal forming modeling program is set up,the partition of unity method is used to compute the integrations in weak form equations and penalty method is used to impose the essential boundary condition exactly.Metal forming examples,such as sheet metal superplastic tension forming and metal rigid viscoplastic tension forming,are analyzed to demon- strate the performance of mesh free method.
基金supported by National Natural Science Foundation of China(Grant No. 51075198)Jiangsu Provincial Natural Science Foundation of China(Grant No. BK2010479)+1 种基金Jiangsu Provincial Project of 333 Talents Engineering of ChinaJiangsu Provincial Project of Six Talented Peak of China
文摘Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for the verification of free-form surface profile are available, the profile parameters of free-form surface are proposed by referring to ISO standards regarding form tolerances and considering its complexity and non-rotational symmetry. Non-uniform rational basis spline（NURBS） for describing free-form surface is formulated. Crucial issues in surface inspection and profile error verification are localization between the design coordinate system（DCS） and measurement coordinate system（MCS） for searching the closest points on the design model corresponding to measured points. A quasi particle swarm optimization（QPSO） is proposed to search the transformation parameters to implement localization between DCS and MCS. Surface subdivide method which does the searching in a recursively reduced range of the parameters u and v of the NURBS design model is developed to find the closest points. In order to verify the effectiveness of the proposed methods, the design model is generated by NURBS and the measurement data of simulation example are generated by transforming the design model to arbitrary position and orientation, and the parts are machined based on the design model and are measured on CMM. The profile errors of simulation example and actual parts are calculated by the proposed method. The results verify that the evaluation precision of freeform surface profile error by the proposed method is higher 10%-22% than that by CMM software. The proposed method deals with the hard problem that it has a lower precision in profile error evaluation of free-form surface.
基金supported by the National Natural Science Foundation of China (No. 10772014)
文摘The direct separation of variables is used to obtain the closed-form solutions for the free vibrations of rectangular Mindlin plates. Three different characteristic equations are derived by using three different methods. It is found that the deflection can be expressed by means of the four characteristic roots and the two rotations should be expressed by all the six characteristic roots,which is the particularity of Mindlin plate theory. And the closed-form solutions,which satisfy two of the three governing equations and all boundary conditions and are accurate for rectangular plates with moderate thickness,are derived for any combinations of simply supported and clamped edges. The free edges can also be dealt with if the other pair of opposite edges is simply supported. The present results agree well with results published previously by other methods for different aspect ratios and relative thickness.
文摘With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu ctive materials away and polishes work-piece of free-form surface. The study o f the contact force between the end of polishing tool and the surface of work-p iece is the key for the compliant EDM to study its cutting mechanism and to make better use of it. This paper makes a model for the contact force and verifies i t by experiments and simulation based on the theory of elastic body kinetics and dynamic stress concentration. The research work shows that this contact force i s caused by both the electrical impulsion of EDM and the mechanical force of ult rasonic vibration, the discharge frequency of compliant EDM has a much more clos er connection with the vibration frequency of polishing tool rather than the fre quency of ultrasonic vibration.
