Corrected Formula of Bed Resistance Coefficient for Plane Numerical Simulation of Tidal Current

By means of a logarithm law for the velocity profile, a corrected formula of bed resistance coefficient, which involves many factors such as gradient of still water depth, variation of surface elevation, flow direction, and so on, is derived from the 3D governing equations of tidal current by averaging over the whole water depth. Theoretical analysis and application have shown that the 2D plane tidal current numerical model would be more reasonable and could be applied to steep bottom topography when the corrected bed resistance coefficient is used, therefore the results of reproduction simulation and engineering calculation would be more scientific and reasonable.

Single-phase-to-ground fault protection based on zero-sequence current ratio coefficient for low-resistance grounding distribution network

Definite-time zero-sequence over-current protection is presently used in systems whose neutral point is grounded by a low resistance(low-resistance grounding systems).These systems frequently malfunction owing to their high settings of the action value when a high-impedance grounding fault occurs.In this study,the relationship between the zero-sequence currents of each feeder and the neutral branch was analyzed.Then,a grounding protection method was proposed on the basis of the zero-sequence current ratio coefficient.It is defined as the ratio of the zero-sequence current of the feeder to that of the neutral branch.Nonetheless,both zero-sequence voltage and zero-sequence current are affected by the transition resistance,The influence of transition resistance can be eliminated by calculating this coefficient.Therefore,a method based on the zero-sequence current ratio coefficient was proposed considering the significant difference between the faulty feeder and healthy feeder.Furthermore,unbalanced current can be prevented by setting the starting current.PSCAD simulation results reveal that the proposed method shows high reliability and sensitivity when a high-resistance grounding fault occurs.

WAVE CURRENT FORCE COEFFICIENTS ON INCLINED CYLINDER AND A NEW ESTIMATION METHOD

Based on the review of present force coefficients estimation methods, a new method in the frequency domain, revised cross-spectrum estimation method, is presented in this paper. Some experiments on the wave-current force on inclined cylinders are also described and the wave current force coefficients are estimated by the revised cross-spectrum estimation method. From the results, it is found that the wave and current directions have some regular effect on the coefficients. According to the results, some empirical formulas are obtained for converting the wave-current force coefficients on inclined cylinders into a unified coefficient. Comparisons show that the unified coefficients are in good agreement with other results.

Impacts of Wave and Current on Drag Coefficient and Wind Stress over the Tropical and Northern Pacific

By taking into consideration the effects of ocean surface wave-induced Stokes drift velocity Un, and current velocity Uc on the drag coefficient, the spatial distributions of drag coefficient and wind stress in 2004 are computed over the tropical and northern Pacific using an empirical drag coefficient parameterization formula based on wave steepness and wind speed. The global ocean current field is generated from the Hybrid Coordinate Ocean Model （HYCOM） and the wave data are generated from Wavewatch Ill （WW3）. The spatial variability of the drag coefficient and wind stress is analyzed. Preliminary results indicate that the ocean surface Stokes drift velocity and current velocity exert an important influence on the wind stress. The results also show that consideration of the effects of the ocean surface Stokes drift velocity and current velocity on the wind stress can significantly improve the modeling of ocean circulation and air-sea interaction processes.

A Higher Order BEM for Wave-Current Action on Structures—Direct Computation of Free-Term Coefficient and CPV Integrals

A higher order boundary dement method （HOBEM） is implemented for wave-current action on structures. The freeterm coefficient and Cauchy principal value （ GPV） integrals are computed by direct methods. Numerical experiments are carried out to validate the computation of free-term coefficient and GPV integrals. The results show that the computation precision of free-term coefficient is very high for various bodies, even with edges and corners, and the convergence speed is fast for CPV integrals for different meshes. The comparison of the second order mean drift force due to wave-current action on a uniform cylinder is made with an analytic solution. It is found that good agreement exists between the present calculation and the analytic solutions. Finally, the numerical code is applied for computing wave-current action on Snorrc TLP.

Study on Distribution Coefficient of Traction Return Current in High-Speed Railway

The distribution coefficient of return current network is an important method to decrease the rail potential. In order to resolve the problem of high rail potential in high-speed railway based on EN50122-1 and Pr EN50170 the distribution coefficient of longitudinal traction return current conductors is calculated through changing the interval of transverse connection. Based on field data and theoretical analysis, the parameters of longitudinal traction return current conductors are calculated. Results indicate that the best distance of the transverse connection is 400 m – 600 m.

The coefficient of variation representing the non-uniformity of the strain field and its implication to detect earthquake precursor

Before the major earthquake or rock damage occurs,it is often accompanied by a sudden change in the degree of non-uniformity of the strain field.In order to find a stronger non-uniformity signal before the rock failure,the coefficient of variation(Cv)is examined and reformed in this study.We test the Cv calculation way of the"normal-abnormal"model proposed in the previous studies.Based on the analysis of the physical process of rock failure and its relationship to the shear strain field,we construct a new way to calculate the Cv value.The variation of shear strain field on rock sample with the increase of stress is obtained by the digital speckle correlation method(DSCM).The new Cv value calculation way is used to study the non-uniformity of the spatial distribution for the shear strain field.The results show that this Cv calculation way can get more obvious abnormal signals.When the number of observation points are limited,the specific distribution of points can increase the signal strength,which may provide reference for the research on precursor detection of earthquakes.

The Nonideality Coefficient of Current-Voltage Characteristics for Asymmetric p-n-Junctions in a Microwave Field

It is shown that the nonideality coefficient m actually depends on the electron temperature Te, and the hole temperature Th. We get more general expression for the nonideality coefficient, taking into account the concentration of electrons and holes, as well as their temperature, coefficient and diffusion length, the temperature of the phonons, the applied voltage, and the height of the potential barrier.

Current dependence coefficient determination for different DC standard resistors measurements based on Ⅴ-Ⅰ method

Current dependence and stability of the measured resistance value are very important for the accurate measurement of DC standard resistor. In this paper, the volt-ampere （V-I） measurement method has been applied to study the current depend-ence of four different types of standard resistors. Diverse values are obtained through the investigation of their stability at dif-ferent currents. Therefore, the current dependence coefficient （CDC） can be determined for each one of the studied resistors. Research shows CDC depends on the applied current value, the measurement time and the resistor type, as clearly demonstra-ted in this research.

Effect of current density on distribution coefficient of solute at solid-liquid interface

When current passes through the solid-liquid interface, the growth rate of crystal, solid-liquid interface energy and radius of curvature at dendritic tip will change. Based on this fact, the theoretical relation between the distribution of solute at solid-liquid interface and current density was established, and the effect of current on the distribution coefficient of solute through effecting the rate of crystal growth, the solid-liquid interface energy and the radius of curvature at the dendritic tip was discussed. The results show that as the current density increases, the distribution coefficient of solute tends to rise in a whole, and when the former is larger than about 400 A/cm 2, the latter varies significantly.

Effect of non-uniform swelling on coal multiphysics during gas injection: The triangle approach

In current dual porosity/permeability models,there exists a fundamental assumption that the adsorption-induced swelling is distributed uniformly within the representative elementary volume (REV),irrespective of its internal structures and transient processes.However,both internal structures and transient processes can lead to the non-uniform swelling.In this study,we hypothesize that the non-uniform swelling is responsible for why coal permeability in experimental measurements is not only controlled by the effective stress but also is affected by the adsorption-induced swelling.We propose a concept of the swelling triangle composed of swelling paths to characterize the evolution of the non-uniform swelling and serve as a core link in coupled multiphysics.A swelling path is determined by a dimensionless volumetric ratio and a dimensionless swelling ratio.Different swelling paths have the same start and end point,and each swelling path represents a unique swelling case.The swelling path as the diagonal of the triangle represents the case of the uniform swelling while that as the two perpendicular boundaries represents the case of the localized swelling.The paths of all intermediate cases populate inside the triangle.The corresponding relations between the swelling path and the response of coal multiphysics are established by a non-uniform swelling coefficient.We define this method as the triangle approach and corresponding models as swelling path-based ones.The proposed concept and models are verified against a long-term experimental measurement of permeability and strains under constant effective stress.Our results demonstrate that during gas injection,coal multiphysics responses have a close dependence on the swelling path,and that in both future experiments and field predictions,this dependence must be considered.

磁驱动固体套筒实验模拟中的电流系数

采用不可压缩理论模型,对FP-2装置上开展的磁驱动固体套筒实验进行了模拟分析。模拟结果表明,无论是二维磁流体力学理论模型,还是其他不可压缩理论模型,回流罩结构磁驱动固体套筒的边界磁感应强度公式中都包含一个小于1的套筒电流系数。对不同套筒厚度、不同套筒半径条件下磁驱动固体套筒实验的电流系数进行了模拟,发现电流系数不仅与套筒内半径有关,还与套筒厚度有关;套筒内半径越大,套筒电流系数越小;套筒厚度越大,套筒电流系数越小。准确掌握磁驱动固体套筒电流系数的变化规律,可使磁流体程序从磁驱动固体套筒实验的后验模拟发展为精确预测,使磁流体力学模型真正具备正确设计和指导磁驱动固体套筒相关实验的理论能力。

Two-Dimensional Mathematical Model of Tidal Current and Sediment for Oujiang Estuary and Wenzhou Bay

A 2-D mathematical model of tidal current and sediment has been developed for the Oujiang Estuary and the Wenzhou Bay. This model accomodates complicated features including multiple islands, existence of turbidity, and significant differ-ence in size distribution of bed material. The governing equations for non-uniform suspended load and bed load transport are presented in a boundary-fitted orthogonal curvilinear coordinate system. The numerical solution procedures along with their initial conditions, boundary conditions, and movable boundary technique are presented. Strategies for computation of the critical condition of deposition or erosion, sediment transport capacity, non-uniform bed load discharge, etc. are suggested. The model verification computation shows that, the tidal levels computed from the model are in good agreement with the field data at the 18 tidal gauge stations. The computed velocities and flow directions also agree well with the values measured along the totally 52 synchronously observed verticals distributed over 8 cross sections. The coraputed tidal water throughputs through the Huangda'ao cross section are close to the measured data. And the computed values of bed deformation from Yangfushan to the estuary outfall and in the outer-sea area are in good agreement with the data observed from 1986 to 1992. The changes of tidal volumes through the estuary, velocities in different channels and the bed form due to the influence of the reclamation project on the Wenzhou shoal are predicted by means of this model.

Experimental Study of Hydrodynamic Loading on Submarine Composite Pipelines under the Action of Waves and Current

This article is aimed at the experimental study of the hydrodynamic loading induced by waves and current acting on the JZ 20-2 submarine composite pipelines. The corresponding hydrodynamic coefficients obtained in this experimental study can be applied to engineering projects.

Current-voltage characteristics of lead zirconate titanate/nickel bilayered hollow cylindrical magnetoelectric composites

Current--voltage measurements obtained from lead zirconate titanate/nickel bilayered hollow cylindrical magnetoelectric composite showed that a sinusoidal current applied to the copper coil wrapped around the hollow cylinder circumference induces voltage across the lead zirconate titanate layer thickness. The current--voltage coefficient and the maximum induced voltage in lead zirconate titanate at 1~kHz and resonance （60.1~kHz） frequencies increased linearly with the number of the coil turns and the applied current. The resonance frequency corresponds to the electromechanical resonance frequency. The current--voltage coefficient can be significantly improved by optimizing the magnetoelectric structure geometry and/or increasing the number of coil turns. Hollow cylindrical lead zirconate titanate/nickel structures can be potentially used as current sensors.

An Improvement on Current Sharing Characteristics of Poloidal Field (PF) AC-DC Converters

In response to the current imbalance phenomenon and its harmfulness, a current sharing circuit model is built up, which reveals the underlying causes for the current imbalance through a quantitative analysis. Then, a feasible approach of improvement, namely enlargement of the length of connection busbars, is proposed. After the amendment, it can be seen that the current sharing coefficient is ahnost unity under rated or fault current conditions.

Investigation of Dynamic Behavior in 1D Non-uniform Granular System

We present a non-uniform granular system in one-dimensional case, whose granularity distribution has the fractal characteristic. The particles are subject to inelastic mutual collisions and obey Langevin equation between collisions. By Monte Carlo simulation we study the dynamic actions of the system. Far from the equilibrium, i.e., τ 〉〉 τe, the results of simulation indicate that the inhomogeneity of the system and the inelasticity of the particles have great influences on the dynamic properties of the system, and correspondingly the influence of the inhomogeneity is more significant.

Numerical simulation on rotordynamic characteristics of annular seal under uniform and non-uniform flows

Currently, the flow field of annular seals disturbed by the circular whirl motion of rotors is usually solved using computational fluid dynamics(CFD) to evaluate the five rotordynamic coefficients. The simulations are based on the traditional quasi-steady method. In this work, an improved quasi-steady method along with the transient method was presented to compute the rotordynamic coefficients of a long seal. By comparisons with experimental data, the shortcomings of quasi-steady methods have been identified. Then, the effects of non-uniform incoming flow on seal dynamic coefficients were studied by transient simulations. Results indicate that the long seal has large cross stiffness k and direct mass M which are not good for rotor stability, while the transient method is more suitable for the long seal for its excellent performance in predicting M. When the incoming flow is non-uniform, the stiffness coefficients vary with the eccentric directions. Based on the rotordynamic coefficients under uniform incoming flow, the linearized fluid force formulas, which can consider the effects of non-uniform incoming flow, have been presented and can well explain the varying-stiffness phenomenon.

Study and innovation of a flexible blade turbine,a new type of tidal current generating device

Utilization of tidal current is becoming a focus of marine energy research and development field. In this paper, a new type of tidal current power generating device which was called flexible blade turbine was put forward. A scale model testing was carried out, and results show that the models performed as expected with good hydrodynamic characteristics. Based on analysis of the results, a scale model turbine with a rated power of 5 kW was constructed, which was an optimal scheme of the flexible blade turbine having higher coefficient of power and power generation capacity. Sea trials were carried out in the Zhaitang Island Channel to evaluate the performance of the turbine. Results show that the turbine performed well, generating the power predicted.

The Introduction of Specific Water and Maximum Airborne Specific Water &the Improvement of Dynamic Equations on Non-Uniform Saturated Moist Atmosphere

To eliminate the irrational supposition that condensed liquid water always falls immediately, specific water m?and maximum airborne specific water mm are introduced into the dynamic framework on non-uniform saturated moist atmosphere (m?is the ratio of the airborne liquid water mass to the moist air mass in unit cubage moist air, mm is its maximum value with , , and are airborne coefficient, vertical velocity and saturated specific humidity respectively). The balance equation between water vapor and airborne liquid water is derived. From the balance equation, a new formula of precipitate rate is got. The analysis shows that in the air stream with some upward vertical velocity ( ), the condensed liquid water can precipitate under the condition with (q is specific humidity) and? only, otherwise it is detained in the air and becomes airborne liquid water. Not only does precipitating liquid water contain condensed liquid water, but also contains converged and existing airborne liquid water. Following above discussion, improved dynamic equations on non-uniform saturated moist atmosphere are provided.