Contemporary tectonic stress field in China

The contemporary tectonic stress field in China is obtained on the basis of Chinese stress field database and Harvard CMT catalogue. Result of the inverted tectonic stresses shows that the maximum principal stress axis strikes nearly north-south direction in the west part of Tibet plateau, ENE direction in North China. In Central China, its strikes show a ra- diated pattern, i.e., NNE in north part and NNW in south part. The detailed stress field parameters of nearly whole China are given and can be used in geodynamic stress field simulation and earthquake prediction.

Active Faulting Pattern,Present-day Tectonic Stress Field and Block Kinematics in the East Tibetan Plateau

This paper examines major active faults and the present-day tectonic stress field in the East Tibetan Plateau by integrating available data from published literature and proposes a block kinematics model of the region. It shows that the East Tibetan Plateau is dominated by strike-slip and reverse faulting stress regimes and that the maximum horizontal stress is roughly consistent with the contemporary velocity field, except for the west Qinling range where it parallels the striking of the major strike-slip faults. Active tectonics in the East Tibetan Plateau is characterized by three faulting systems. The left-slip Kunlun-Qinling faulting system combines the east Kunlun fault zone, sinistral oblique reverse faults along the Minshan range and two major NEE-striking faults cutting the west Qinling range, which accommodates eastward motion, at 10--14 mm/a, of the Chuan-Qing block. The left-slip Xianshuihe faulting system accommodated clockwise rotation of the Chuan-Dian block. The Longmenshan thrust faulting system forms the eastern margin of the East Tibetan Plateau and has been propagated to the SW of the Sichuan basin. Crustal shortening across the Longmenshan range seems low （2-4 mm/a） and absorbed only a small part of the eastward motion of the Chuan-Qing block. Most of this eastward motion has been transmitted to South China, which is moving SEE-ward at 7-9 mm/a. It is suggested from geophysical data interpretation that the crust and lithosphere of the East Tibetan Plateau is considerably thickened and theologically layered. The upper crust seems to be decoupled from the lower crust through a decollement zone at a depth of 15-20 kin, which involved the Longmenshan fault belt and propagated eastward to the SW of the Sichuan basin. The Wenchuan earthquake was just formed at the bifurcated point of this decollement system. A rheological boundary should exist beneath the Longmenshan fault belt where the lower crust of the East Tibetan Plateau and the lithospheric mantle of the Yangze block are juxtaposed.

Simulation of Paleotectonic Stress Fields and Distribution Prediction of Tectonic Fractures at the Hudi Coal Mine, Qinshui Basin

Study on tectonic fractures based on the inversion of tectonic stress fields is an effective method. In this study, a geological model was set up based on geological data from the Hudi Coal Mine, Qinshui Basin, a mechanical model was established under the condition of rock mechanics and geostress, and the finite element method was used to simulate the paleotectonic stress field. Based on the Griffith and Mohr-Coulomb criterion, the distribution of tectonic fractures in the Shanxi Formation during the Indosinian, Yanshanian, and Himalayan period can be predicted with the index of comprehensive rupture rate. The results show that the acting force of the Pacific Plate and the India Plate to the North China Plate formed the direction of principal stress is N-S, NW - SE, and NE - SW, respectively, in different periods in the study area. Changes in the direction and strength of the acting force led to the regional gradients of tectonic stress magnitude, which resulted in an asymmetrical distribution state of the stress conditions in different periods. It is suggested that the low-stress areas are mainly located in the fault zones and extend along the direction of the fault zones. Furthermore, the high-stress areas are located in the junction of fold belts and the binding site of multiple folds. The development of tectonic fractures was affected by the distribution of stress intensity and the tectonic position of folds and faults, which resulted in some developed areas with level I and II. There are obvious differences in the development of tectonic fractures in the fold and fault zones and the anticline and syncline structure at the same fold zones. The tectonic fractures of the Shanxi Formation during the Himalayan period are more developed than those during the Indosinian and Yanshanian period due to the superposition of the late tectonic movement to the early tectonic movement and the differences in the magnitude and direction of stress intensity.

The Relationship between Fractures and Tectonic Stress Field in the Extra Low-Permeability Sandstone Reservoir at the South of Western Sichuan Depression

The formation and distribution of fractures are controlled by paleotectonic stress field, and their preservative status and effects on development are dominated by the modern stress field. Since Triassic, it has experienced four tectonic movements and developed four sets of tectonic fractures in the extra low-permeability sandstone reservoir at the south of western Sichuan depression. The strikes of fractures are in the S-N, NE-SW, E-W, and NW-SE directions respectively. At the end of Triassic, under the horizontal compression tectonic stress field, for which the maximum principal stress direction was NW.SE, the fractures were well developed near the S-N faults and at the end of NE-SW faults, because of their stress concentration. At the end of Cretaceous, in the horizontal compression stress fields of the NE-SW direction, the stress was obviously lower near the NE-SW faults, thus, fractures mainly developed near the S-N faults. At the end of Neogene-Early Pleistocene, under the horizontal compression tectonic stress fields of E-W direction, stress concentrated near the NE-SW faults and fractures developed at these places, especially at the end of the NE-SE faults, the cross positions of NE-SW, and S-N faults. Therefore, fractures developed mostly near S-N faults and NE-SW faults. At the cross positions of the above two sets of faults, the degree of development of the fractures was the highest. Under the modern stress field of the NW-SE direction, the NW-SE fractures were mainly the seepage ones with tensional state, the best connectivity, the widest aperture, the highest permeability, and the minimum opening pressure.

End Late Paleozoic tectonic stress field in the southern edge of Junggar Basin

This paper presents the end Late Paleozoic tectonic stress field in the southern edge of Junggar Basin by interpreting stress-response structures （dykes, folds, faults with slickenside and conjugate joints）. The direction of the maximum principal stress axes is interpreted to be NW-SE （about 325°）, and the accommodated motion among plates is assigned as the driving force of this tectonic stress field. The average value of the stress index Rt is about 2.09, which indicates a variation from strike-slip to compressive tectonic stress regime in the study area during the end Late Paleozoic period. The reconstruction of the tectonic field in the southern edge of Junggar Basin provides insights into the tectonic deformation processes around the southern Junggar Basin and contributes to the further understanding of basin evolution and tectonic settings during the culmination of the Paleo- zoic.

Kinematic History and Changes in the Tectonic Stress Regime during the Cenozoic along the Qinling and Southern Tanlu Fault Zones

Since the mid-late Eocene, North China has been subjected to extensional stress, resulting in the formation and development of basins. The dynamic origin of this crustal extension has long been an issue of debate. This paper presents the results of kinematic analyses of faults obtained from two seperated areas in North China. In the Weihe graben situated on the southernmost margin of the Ordos block, analyses of fault kinematics were coupled with an analysis of the basin's subsidence history. Three successive extensional tectonic phases accompaning the basin's formation and development have been distinguished. The Palaeogene extension was oriented in a WNW-ESE direction; the Neogene extension in a NE-SW direction and the Pliocene-Quaternary extension in a NW-SE direction. Such changes have also been recorded by fault kinematics along the southern Tanlu fault zone. This has been demonstrated by three successive sets of fault striations indicating normal dip slip resulting from NW-SE extension, then left-lateral slip with a normal component resulting from NE-SW extension, and right-lateral slip with a minor normal component, respectively. The kinematic history of faults and their chronological evolution indicate changes in continental dynamics acting in North China over Cenozoic time.

Evolution characteristics of Quaternary tectonic stress field in the north and east margin of Qinghai-Xizang plateau

By inversion of fault slip data for Quaternary tectonic stress field and the analysis of crustal deformation after lateTeriary. we explaincd the evolution of crustal dynamic about the north and east margin of Qinghai-Xizang (Tibet)plateau since Miocenc. From middle or late Miocene to early Pleistocene, the tectonic stress field was featured by amaximum principal compression which was coming from the collision of india Plate continued to the boundaryof the plateau. and was basically of reverse faulting type. Since the late period of early Pleistocene, Pleistocene continuedto push northward and the compressional deformation of the plateau interior increased continuously, meanwhile,N W-SE extension appeared on the east side of the plateau. This formed a favorable condition for the interior block offoe plateau to slide towards east and southeast, causing the faults surrounding the plateau to change from thrust tostrike-slip. -The contemporary tectonic stress field was formed from the late period of early Pleistocene and continuedto present. The direction of maximum principal compressional stress rotated clockwise with respect to the previoustectonic stress held. the stress field was mainly of strike-slip type.

Three dimensional tectonic stress field in North China

According to the latest data of geological structure, geophysics, in-situ stress measurement and focal mechanism,3-D tectonic stress field model in North China is built and 3-D tectonic stress field pattern of North China aresimulated by finite element method. Then the overall characteristics and regional specific feature of North Chinaare studied. Finally, the influences of the valid dynamic boundary conditions of North China Block, active faultsand the inhomogeneity of crustal medium on tectonic stress field of North China are investigated.

Modern tectonic stress field in the Chinese mainland inverted from focal mechanism solutions

The inversion of modern tectonic stress field in China is made by regions on the basis of focal mechanism data inthe period of 1920-1996. Results of the inversion show that the maximum principal compressive stress σ1 axisstrikes nearly north-south direction in the Tibet Plateau and western Chin4 east-west direction in North China Incentral China, its strikes show a radiate pattern, i.e., north-north east in north part, east-west in central part andnorth-north west in south part. The σ1 axes are often perpendicular to the minimum principal stress σ3 axes, exceptwestern China where the σ1 axes are oblique to the σ3 axes with an acute angle. R is defined by (σ2-σ1)/(σ3-σ1),has the higher values (0.60-0.90) in north part of central China and quickly changes into the lower values(0. 10-0.30) in the Tibet Plateau. Both of the observed and inverted fault planes have strikes varying with locations.Combining stress directions and R value, the stress configuration is divided into 7 groups. Most of the groups showstrike-slip faulting with intermediate R values, which occupies North China and the eastern part of China as well asinner Tibet Plateau. A few of them show reverse faulting with higher R values within western pod of China and thenorth edge of the Tibet Plateau. Normal faulting occurred on the south edge of the Tibet Plateau with smaller Rval nes.

Determination of the direction and magnitude of recent tectonic stress in the Xianshuihe fault zone using fault slip data

In this article,a method to determine the complete stress tensor by use of fault slip data in combination with experimental parameters of rock mechanics is elucidated;the direction and magnitude of recent tectonic stress in the Xianshuihe fault zone are determined by this method from a great deal of active fault striae data observed in the fault zone and the envelope of rock fracture determined experimentally for rock samples collected from the fault zone;and the applicability of the method and reliability of calculation results are discussed.

The seismicity and tectonic stress field characteristics of the Longmenshan fault zone before the Wenchuan M_S8.0 earthquake

The seismicity of Longrnenshan fault zone and its vicinities before the 12 May 2008 Wenchuan Ms8.0 earthquake is studied. Based on the digital seismic waveform data observed from regional seismic networks and mobile stations, the focal mechanism solutions are determined. Our analysis results show that the seismicities of Longmenshan fault zone before the 12 May 2008 Wenchuan earthquake were in stable state. No obvious phenomena of seismic activity intensifying appeared. According to focal mechanism solutions of some small earthquakes before the 12 May 2008 Wenchuan earthquake, the direction of principal compressive stress P-axis is WNW-ESE. The two hypocenter fault planes are NE-striking and NW-striking. The plane of NE direction is among N50°-70°E, the dip angles of fault planes are 60°-70° and it is very steep. The faultings of most earthquakes are dominantly characterized by dip-slip reverse and small part of faultings present strike-slip. The azimuths of principal compressive stress, the strikes of source fault planes and the dislocation types calculated from some small earthquakes before the 12 May 2008 Wenchuan earthquake are in accordance with that of the main shock. The average stress field of micro-rupture along the Longmenshan fault zone before the great earthquake is also consistent with that calculated from main shock. Zipingpu dam is located in the east side 20 km from the initial rupture area of the 12 May 2008 Wenchuan earthquake. The activity increment of small earthquakes in the Zipingpu dam is in the period of water discharging. The source parameter results of the small earthquakes which occurred near the initial rupture area of the 12 May 2008 Wenchuan earthquake indicate that the focal depths are 5 to 14 km and the source parameters are identical with that of earthquake.

Modern tectonic stress field in Southwest Yunnan, China

By means of inversion of fault slip data, the parameters of 20 tectonic stress tensors in Southwest Yunnan region are determined. Compared with the average stress field of the region obtained from focal mechanism solutions, the following characteristics of modern tectonic stress field in this region are obtained. From the west of Zhenyuan-Yingpanshan fault to the south of Longling fault zone, the maximum compressional stress is in NNE direction and the stress regime is mainly of strike-slip type. In Longling fault zone and the area north to it, the direction of maximum compressional stress is near-NS or NNW, the stress regime is of strike-slip type.

Similarity simulation of bolt support in a coal roadway in a tectonic stress field

In order to study the mechanism of bolt support and the behavior of strata in a coal roadway under tectonic stress,deformation and destruction of a roof,floor and sides were studied using an experiment in similarity simulation.We also studied the mechanism and types of bolt support functions in the coal roadway.The results show that with an increase in horizontal tectonic stress,the strata in the roof and floor of the roadway gradually separate and become shear failure areas.Coal in side walls moves,but its integrity remains intact.Side bolts are mainly affected by tension and roof bolts by the effect of shear.

Numerical calculations of tectonic stress field of Chinese mainland and its neighboring regions and their applications to explanation of seismic activity

This paper made a numerical simulation to the basic tectonic stress field of Chinese mainland and its neighboringregion using the visco-elasticity finite element model and the new published displacement rate result. Main contents include the simulation of maximum shear stress and its varying rate, the maximum shear strain and its varyingrate, the shear strain energy density and its varying rate. In view of the high inhomogeneous distribution characterof seismicity in space and time in Chinese mainland and its neighboring area, the normalized background energyvalue was given by means of normalized treatment to the earthquake energy release in the eastern and westernparts of Chinese mainland. And the comparison of the simulation result with the actual seismicity was made. Thefesults show that the simulation values can explain well the earthquake distribution character of Chinese mainlandand its neighboring area.

Numerical modeling of tectonic stress field and fault activity in North China

On the basis of a 3-dimension visco-elastic finite element model of lithosphere in North China, we numerically simulate the recent mutative figures of tectonic stress field. Annual change characteristics of stress field are： 1 ） Maximum principal tensile stress is about 3 -9 kPaa-1 and its azimuth lie in NNW-SSE. 2） Maximum principal compressive stress is about 1 - 6 kPaa-1 and its azimuth lie in NEE-SWW. 3 ） Maximum principal tensile stress is higher both in the west region and Liaoning Province. 4） Variation of tectonic stress field benefits fault movement in the west part and northeast part of North China. 5 ）Annual accumulative rates of Coulomb fracture stress in Tanlu fault belt have segmentation patterns： Jiashan-Guangji segment is the high- est （6 kPaa - 1 ） , Anshan-Liaodongwan segment is the second （5 kPaa - l ） , and others are relatively lower （ 3 - 4 kPaa-1 ）.

Rules of distribution in a plastic zone of rocks surrounding a roadway affected by tectonic stress

In order to study the rules of distribution in a plastic zone of rocks, surrounding a roadway, affected by tectonic stress, we first analyzed the mechanics of a roadway affected by tectonic stress and derived a theoretical formula for the plastic zone of rocks surrounding a roadway. We also analyzed the distribution characteristics of the plastic zone under different levels of tectonic stress, vertical pressure, cohesion and friction angle of the surrounding rock. Secondly, we used numerical simulation to analyze the range and shape features of the plastic zone of rocks surrounding the roadway, given different tectonic stress levels. Finally we used a rock drilling detector to carry out field measurements on the broken state of rock surrounding the roadway at the –700 substation and channels in the Xinzhuang mine of the Shenhuo mining area. Given the measured ground stress, we analyzed the relationship between tectonic stress and the distribution of this plastic zone. Our results show that the range of the plastic zone at the top and bottom of the roadway increases with an increase in tectonic stress and this increase is especially obvious at the roadway corner.

Preliminary analysis on the tectonic stress level in the source region of Tangshan earthquake

The abundant data of focal mechanism solutions in Tangshan region, China, are inverted for the tectonic stress field. Combined with tectonophysical consideration, the magnitude of the three principal stresses, as well as their vertical variation under the average crustal rock property, in the source region of the 1976 Tangshan earthquake is estimated. The relationship between crustal stress and friction mc, pore pressure P0 and stress shape factor F is studied. The paper draws the conclusion that the vertical increasing rate of the maximum principal stress s is directly proportional to friction, and inversely to pore pressure P0 and stress shape factor F ; while the vertical increasing rate of the minimum principal tress s is directly proportional to pore pressure P0, inversely to friction mc and stress shape factor F. This study is a try to invert the data of focal mechanism solutions for the complete stress tensor.

Present-day tectonic stress in the East China Sea region and its possible origin

This paper analyzes bore-hole wall breakouts of the 5 wells located in southern part of the East China Sea regionwith logging sections deeper than 3 000 m and logging intervals longer than 1 000 m or even near 2 000 m. Bymaking a combined study of the breakout characteristics of these 5 wells and 11 other wells analyzed in Xu andWu (1997). it is inferred that the maximum horizontal principal compressive stress in the East China Sea 'region isgenerally in NE-SW direction, and the horizontal differential stress there is possibly weak. P- and T-axisorientations of focal mechanism of earthquakes occurred from 1977 to 1998 in the region of O kinawa trough andRyukyu Islands are investigated. p-axes of earthquakes in Okinawa trough are generally oriented NE-SW,coinciding with the trough stretching trend. while T-axes are nearly perpendicular to the trend. This indicates thatthe horizontal action of the Philippine Sea Plate to the East China Sea region is not pushing but pulling. A two dimensional finite element simulation is conducted to study the origin of the present-day tectonic stress in the EastChina Sea region. The result shows that the stress there is possibly attributable to both the strong northwestwardcompression in Taiwan region and the back-arc extension of the Ryukyu island arc. Less strong ear thquakes in theEast China Sea region is possibly related to the weak horizontal shear stress there.

Study on relation between tectonic stress and coal-mining subsidence with similar material simulation

Using a minitype and stress-type test device for similar material simulation of coal-mining subsidence, the relation between tectonic stress and coal-mining subsidence was successfully simulated, furthermore, the test period of similar material simulation was obviously shortened and the test process was more dexterous and convenient. To do simi-lar material simulation with the minitype and stress-type test device was feasible and high-efficient. Bringing two models with the same geological and mining conditions to bear lateral compressive stress and tensile stress respectively and simulating the process of underground mining, the test results indicate that: under the compressive stress, the col-lapse of the coal roof occurs belatedly and the damaged range in cover of coal seam is smaller, therefore the movement and deformation of the cover and its damage to the ground geological environment are not evident; whereas under tensile stress, the situation is contrary to which mentioned above. A conclusion was obtained from the test that the ground environment hazards in coal mining areas were controlled by the regional geo-logical tectonic stress field.

Modern tectonic stress field deeply in Xuzhou Coal Mine

By inverting fault slip data, the parameters of 12 tectonic stress tensors in the mine region can be determined. The following characteristics can be obtained for recent tectonic stress fields, which are found deep in the study region. The results show that the recent tectonic stress field mainly presents the characteristics of near NWW-SSE maximum compressional stress and near NE-SW minimum extensional stress, while the stress regimes are mainly of strike slip, part of the reverse-fault type. Recent tectonic stress field in the region is characterized by horizontal components. The maximum principal compression stress direction was from NEE to SEE, the average principal compression stress direction was near NWW-SSE maximum compres- sional stress and near NE-SW minimum extensional. The recent tectonic stress field of the studied area can be controlled by a large tectonic stress area.