Excitation and Detection of Shear Horizontal Waves with Electromagnetic Acoustic Transducers for Nondestructive Testing of Plates

The fundamental shear horizontal（SH0） wave has several unique features that are attractive for long-range nondestructive testing（NDT）. By a careful design of the geometric configuration, electromagnetic acoustic transducers（EMATs） have the capability to generate a wide range of guided wave modes, such as Lamb waves and shear-horizontal（SH） waves in plates. However, the performance of EMATs is influenced by their parameters. To evaluate the performance of periodic permanent magnet（PPM） EMATs, a distributed-line-source model is developed to calculate the angular acoustic field cross-section in the far-field. Numerical analysis is conducted to investigate the performance of such EMATs with different geometric parameters, such as period and number of magnet arrays, and inner and outer coil widths. Such parameters have a great influence on the directivity of the generated SH0 waves that arises mainly in the amplitude and width of both main and side lobes. According to the numerical analysis, these parameters are optimized to obtain better directivity. Optimized PPM EMATs are designed and used for NDT of strip plates. Experimental results show that the lateral boundary of the strip plate has no perceivable influence on SHO-wave propagation, thus validating their used in NDT. The proposed model predicts the radiation pattern ofPPM EMATs, and can be used for their parameter optimization.

Nondestructive Testing and Characterization of Residual Stress Field Using an Ultrasonic Method

To address the difficulty in testing and calibrating the stress gradient in the depth direction of mechanical components, a new technology of nondestructive testing and characterization of the residual stress gradient field by ultrasonic method is proposed based on acoustoelasticity theory. By carrying out theoretical analysis, the sensitivity coefficients of different types of ultrasonic are obtained by taking the low carbon steel（12%C） as a research object. By fixing the interval distance between sending and receiving transducers, the mathematical expressions of the change of stress and the variation of time are established. To design one sending-one receiving and oblique incidence ultrasonic detection probes, according to Snell law, the critically refracted longitudinal wave（LCR wave） is excited at a certain depth of the fixed distance of the tested components. Then, the relationship between the depth of LCR wave detection and the center frequency of the probe in Q235 steel is obtained through experimental study. To detect the stress gradient in the depth direction, a stress gradient LCR wave detection model is established, through which the stress gradient formula is derived by the relationship between center frequency and detecting depth. A C-shaped stress specimen of Q235 steel is designed to conduct stress loading tests, and the stress is measured with the five group probes at different center frequencies. The accuracy of ultrasonic testing is verified by X-ray stress analyzer. The stress value of each specific depth is calculated using the stress gradient formula. Accordingly, the ultrasonic characterization of residual stress field is realized. Characterization results show that the stress gradient distribution is consistent with the simulation in ANSYS. The new technology can be widely applied in the detection of the residual stress gradient field caused by mechanical processing, such as welding and shot peening.

Statistical analysis of nondestructive testing results of cast steel joints in civil engineering structures

To study the distribution law and random characteristics of casting defects in steel castings,24 civil engineering structural cast steel joints were divided into two groups:simple cast steel joints and complex cast steel joints.Three kinds of nondestructive testing(NDT)methods,namely,visual,magnetic particle,and ultrasonic inspections,were used to detect the macroscopic defects in joints.The NDT results were then statistically analyzed.The results show that the unfused core support is a common defect of complex cast steel joints,and the defect can be seen visually,so excavation and repair welding should be carried out before castings leave factories.Casting cracks are extremely likely to occur in the intersection area of tubes,which is called the ultrasonic inspection blind zone.The occurrence probability of gas pores on simple cast steel joints is the largest,and the occurrence probability of core support incomplete fusions on complex cast steel joints is the largest.However,when cast steel joints are counted as a whole sample,the occurrence probability of gas pores is larger than that of core support incomplete fusions.Therefore,it is the most common defect in cast steel joints.

Nondestructive testing method of wood moisture content based on a planar capacitance sensor model

For our research, a new hybrid experimental-computational method is presented. We applied a least squares fitting method （LSFM） to reconstruct the wood moisture content （WMC） from the data measured with a planar capacitance sensor. A boundary element method （BEM） was used to compute the relationship between capacitance and the dielectric constant. A functional relationship between MC and the dielectric constant was identified by LSFM. The agreement of this final computation result with the experimental data indicates that this method can be used to estimate the WMC quickly and effectively with engineering analysis. Compared with popular statistical methods, a large number of experiments are avoided, some costs of testing are reduced and the efficiency of testing is enhanced.

Recent developments in photoacoustic imaging and sensing for nondestructive testing and evaluation

Photoacoustic(PA)imaging has been widely used in biomedical research and preclinical studies during the past two decades.It has also been explored for nondestructive testing and evaluation(NDT/E)and for industrial applications.This paper describes the basic principles of PA technology for NDT/E and its applications in recent years.PA technology for NDT/E includes the use of a modulated continuous-wave laser and a pulsed laser for PA wave excitation,PA-generated ultrasonic waves,and all-optical PA wave excitation and detection.PA technology for NDT/E has demonstrated broad applications,including the imaging of railway cracks and defects,the imaging of Li metal batteries,the measurements of the porosity and Young’s modulus,the detection of defects and damage in silicon wafers,and a visualization of underdrawings in paintings.

Dynamic Elastic Modulus of Cement Paste at Early Age based on Nondestructive Test and Multiscale Prediction Model

This paper introduced a nondestructive testing method to evaluate the dynamic elastic modulus of cement paste. Moreover, the effect of water-cement ratio and conventional admixtures on the dynamic elastic modulus of cement paste was investigated, in which three kinds of admixtures were taken into account including viscosity modifying admixture （VMA）, silica.fume （SF）, and shrinkage-reducing admixture （SRA）. The experimental results indicate that the dynamic elastic modulus of cement paste increases with decreasing water-cement ratio. The addition of SF increases the dynamic elastic modulus, however, the overdosage of VMA causes its reduction. SRA reduces the dynamic elastic modulus at early age without affecting it in later period. Finally, a multiscale micromechanics approach coupled with a hydration model CEMHYD3D and percolation theory is utilized to predict the elastic modulus of cement paste, and the predictive results by the model are in accordance with the experimental data.

The Application of Impact Echo Scanning on Nondestructive Test of Pavement

A new nondestructive test method-Impact Echo Scanning was introduced. Application of this method on pavement structure test was discussed. A method to increase the measurement accuracy of the test on multi-layers was proposed, and was verified by field test. The test results show that the basic structural information can obtained rapidly and accurately by 3-D scanning of the impact echo system.

Ultrasonic Nondestructive Testing of Superplastic Solid-State Welding Joint for Different Steels

Based on quantitative microscopic examinations of welds and welding rate for different steels(40Cr and T10A) joint,which possess the ultra-fine microstructure after high frequency hardening(HFH) and salt-bath cyclic quenching(SCQ),the suitable defect grey scale threshold value was determined,and the welding rate of superplastic solid-state welding of different steels(40Cr and T10 A steel) was systematically inspected and analyzed by means of self-made ultrasonic imaging inspection system.The experimental results showed that the superplastic solid-state weld of different steels can be inspected more accurately,reliably and quickly by this system,and the results were in good accordance with that of metallographic observation.The welding rate of superplastic welding is in linear relation with tensile strength of joint.

Investigation of Eddy Current Nondestructive Testing for Carbon Fiber-Reinforced Plastic （CFRP） Based on Electromagnetic Field Analysis

CFRP （carbon fiber reinforced plastic） is used extensively in aircraft and spacecraft structures, because of its excellent mechanical properties. Ultrasonic testing, which is used as a non-destructive testing technique for CFRP, requires a contact medium. In contrast, eddy current testing does not require a contact medium, and when used for CFRP testing it has advantages not available with other techniques. CFRP is a laminate, with each layer being anisotropically conductive, and the distribution of the induced eddy current is yet to be determined. Here, to determine the eddy current distribution in the detection of flaws in cross-ply CFRP （0°/90°） by using a cross-point probe, we performed an FEM （finite element method） analysis of electromagnetic fields. We investigated the nature of the flaw signals and the differences in eddy current distributions between materials with and without flaws.

Rolling contact fatigue nondestructive testing system for a bearing inner ring based on initial permeability

Due to the fact that rolling contact fatigue is not easily detected, and residual life is not easily evaluated in the early stage of bearing life, a nondestructive testing method based on initial permeability is proposed. By analyzing the crack propagation mechanism, a fatigue state detection system based on differential signals is designed. A simulation model of the detection of the inner ring of the pulse signal is established by using the electromagnetic field simulation software. The effects of the height of the coil, the inner and outer diameter, the number of coil turns, the diameter and the height of the ferrite core of the probe on the differential value of the detection signal are simulated. The parameter combination of the maximum difference value of the signal is used as the structural size of the sensor, and the detection sensor is designed and fabricated. Moreover, the bearing fatigue test system is designed, and the bearing is tested. The results show that the system has good detection ability for rolling contact fatigue and verifies the mechanism and trend of crack propagation in the inner ring of the bearing.

Compressive Strength Prediction of Porous Concrete Using Nondestructive Tests

This research focused on a prediction of compressive strength in porous concrete based on the ratio of air-entrained agents in the concrete slab using nondestructive testing methods such as the Impact Echo （IE） method, Spectral Analysis of Surface Wave （SASW） method and Free-Free Resonance （FFR） test. The method that best predicts the strength of the concrete slab can be derived from a relationship between compressive strengths and stress wave velocities. Concrete slab specimens of varying air content, were formed with a mix ratio of air-entrained agent of 0%, 0.15%, 0.3%, 0.7% and 1.5% by weight. These slabs were tested and analyzed to measure the stress wave velocities in order to develop a correlation with compressive strengths. The plot between the stress waves and compressive strengths showed a stiffslope up to an air ratio of 4% with a less steep slope beyond this point. In the process of predicting the compressive strength of concrete slab specimens, the prediction of compressive strength based on the compression wave velocity caused an average error of 4.9% in the compression wave velocity, and the prediction of compressive strength based on the surface wave velocity caused an average error of 2.2% in the surface wave velocity.

Breakthrough Made on the Nondestructive Testing of Orbital Spacecraft

Lanzhou Institute of Physics, a subsidiary of CAST, conducted ground testing on its newly developed eddy current nondestructive testing equipment, demonstrating an important breakthrough had been made with the nondestructive testing of orbital spacecraft. The equipment works steadily and has met the design requirements for space applications. It was also announced by the Institute that the equipment would be used during the next lunar exploration mission to detect the status of

Femtosecond laser-acoustic modeling and simulation for AlCu nanofilm nondestructive testing

Photoacoustic detection has shown excellent performance in measuring thickness and detecting defects in metal nanofilms.However,existing research on ultrafast lasers mainly focuses on using picosecond or nanosecond lasers for large-scale material processing and measurement.The theoretical study of femtosecond laser sources for photoacoustic nondestructive testing(NDT)in nanoscale thin film materials receives much less emphasis,leading to a lack of a complete physical model that covers the entire process from excitation to measurement.In this study,we developed a comprehensive physical model that combines the two-temperature model with the acoustic wave generation and detection model.On the basis of the physical model,we established a simulation model to visualize the ultrafast lasermaterial interaction process.The damage threshold of the laser source is determined,and the effect of key parameters(laser fluence,pulse duration,and wavelength)for AlCu nanofilms on the femtosecond photoacoustic NDT process is discussed using numerical results from the finite element model.The numerical results under certain parameters show good agreement with the experimental results.

Nondestructive testing algorithm of building concrete material defects based on machine learning

In order to pay more attention to the quality of construction concrete and accurately judge whether concrete material meets the standard,a nondestructive testing algorithm of building concrete material defects based on machine learning is proposed.Through the ray tracing algorithm of Snell’s theorem,the shortest path between two random punctuation marks of building concrete is calculated.The original coordinate system and grid size were set,the trend and length of the line in the grid were calculated,and the coordinates between the grid corner points and the transmitting probe were calculated so as to obtain the position of the intermediate refractive points of the two probes.Finally,the vector dot product of the local defects is obtained by the optimal hyperplane calculation of the binary classification in the support vector machine.Experimental results show that the proposed method has the advantages of high precision.

Development and application of a high energy X-ray digital radiography nondestructive testing system for a driving mechanism

A high energy X-ray digital radiography(DR)nondestructive testing(NDT)system has been developed to detect the operating state of a driving mechanism.The system consists of five main subsystems,namely,X-ray generator,image intensifier,image processor,mechanical platform and control subsystem.Owning to the mechanical platform,the X-ray generator and image intensifier are able to rotate around the vertical axis from 0°to 360°in 35 s and move along vertical axis within the range of 500 mm in 20 s.The 450 kV X-ray generator provides a maximum 100 mm penetration depth and a coverage angle of 40°,and the resolution of the scanned image is 66 lp/cm.As is indicated by its applications,the system is featured with fast scanning speed,wide detection range and high imaging quality.It can be applied to inspect the defects in the driving mechanism as well.

Surface wave transducer for ultrasonic nondestructive testing of polymer components

In the point of application to ultrasonic nondestructive testing of surface stress and defect in polymer component, the oblique suxface wave transducer is investigated on its acoustic property and especially the mechanism of acoustic attenuation of acoustic entrant material inside the transducer. A new kind of room temperature vulcanized silicone elastomer as wedge material, in which ultrasound can propagate in very low speed with weak attenuation, is developed through a great deal of trials. The corresponding ultrasonic transducer is also designed for further researches and application to detect surface stress and surface crack in aerospace transparent component.

New Wavelet Theory and Application in Nondestructive Testing

A new ultrasound signal processing model that provides fast real-time performance was devel- oped. The model is based on the “rotation angle series fast wavelet transform” algorithm developed for real- time digital signal processing. Instead of the traditional convolution-based algorithms, the algorithm uses a cascaded structure which can be quickly implemented on digital signal processors. The algorithm runs twice as fast as and is more flexible than the fast wavelet transform, and is applicable for multi-channel and phased array ultrasound systems. By using this algorithm, multi-channel ultrasound systems, including phased array ultrasound systems can have less complex software and hardware designs, lower cost, smaller size, and especially more powerful functions.

Enhanced air-coupled impact echo technique by phase analysis of signals from multiple sensors

This paper presents an air-coupled impact echo(IE)technique that relies on the phase spectrum of the collected data to find the frequencies corresponding to the reflections from delaminations.The proposed technique takes advantage of the fact that the IE compression wave is not a propagating wave,but it is the 1st order symmetrical(S1)mode Lamb wave at zero group velocity(S1-ZGV).Therefore,it searches the phase spectra of the data collected by multiple sensors to locate the frequency corresponding to the lowest phase difference.As a result,the technique reduces the effect of propagating waves,including the direct acoustic wave and ambient noise.It is named the Constant Phase IE(CPIE).The performance of the CPIE is experimentally compared with the regular amplitude spectrum-based IE technique and two other multisensor IE techniques.The CPIE shows a performance advantage,especially in a noisy environment.

Assessing efficacy of standard impregnation techniques on die-cast aluminum alloys using X-ray micro-CT

Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements.Vacuum pressure impregnation(VPI)with thermosetting polymers is commonly used to address leakage defects in die-cast Al alloys.In this study,the efficacy of the VPI technique in sealing alloy parts was investigated using a combination of nondestructive micro X-ray computed tomography(micro XCT)and a standard leak test.The results demonstrate that the commonly used water leak test is insufficient for determining the sealing performance.Instead,micro XCT shows distinct advantages by enabling more comprehensive analysis.It reveals the presence of a low atomic number impregnates sealant within casting defects,which has low grey contrast and allows for visualizing primary leakage paths in 3D.The effective atomic number of impregnated resin is 6.75 and that of Al alloy is 13.69 by dual-energy X-ray CT.This research findings will contribute to enhancing the standard VPI process parameters and the properties of impregnating sealants to improve quality assurance for impregnation in industrial metals.

Linear and Nonlinear Ultrasonic Detections of Impact Damage in Composite Laminate

The appearance and accumulation of internal impact damage seriously influence overall performance of carbon fiber reinforced plastic(CFRP).Thus,this study evaluates the change in impact damage number by using linear and nonlinear ultrasonic Lamb wave detection methods,and compares these two detection results.An ultrasonic wave simulation model for composite structure with impact damage is established using the finite element method,and the interaction between impact damage and the ultrasonic wave is simulated.Simulation results demonstrate that the ultrasonic amplitude linearly decreases,and the relative nonlinear parameter linearly increases in proportion to the impact number,respectively.The linear-fitting slope of nonlinear parameter is 0.38 per impact number at an input frequency of 1.0 MHz.It is far higher than that of the linear ultrasonic amplitude,which is only-0.12.However,with the increase of impact damage,the linear growth of nonlinear parameters mainly depends on the decrease in ultrasonic amplitude rather than the accumulation of second harmonic amplitude.In the linear ultrasonic amplitude detection,the linear fitting slope at 1.1 MHz is-0.14,which is lower than those at 0.9 MHz and 1.0 MHz.Meanwhile,in the nonlinear ultrasonic parameter detection,the linear fitting slope at 1.1 MHz is 0.92,which is higher than those at 0.9 MHz and 1.0 MHz.The results show that higher frequencies lead to greater attenuation of ultrasonic amplitude and a larger increase in nonlinear parameters,which can enhance the sensitivity of both linear and nonlinear ultrasonic detections.The accuracy of simulation results is demonstrated through the low-velocity impact and ultrasonic experiments.The results show that compared with nonlinear ultrasonic technology,the linear ultrasonic technology is more suitable for impact damage assessment of carbon fiber reinforced plastic because of its simpler detection process and higher sensitivity.