A three-dimensional mathematical model was developed to investigate the effect of gas blowing nozzle angles on multiphase flow,circulation flow rate,and mixing time during Ruhrstahl-Heraeus(RH) refining process.Also,a...A three-dimensional mathematical model was developed to investigate the effect of gas blowing nozzle angles on multiphase flow,circulation flow rate,and mixing time during Ruhrstahl-Heraeus(RH) refining process.Also,a water model with a geometric scale of 1:4 from an industrial RH furnace of 260 t was built up,and measurements were carried out to validate the mathematical model.The results show that,with a conventional gas blowing nozzle and the total gas flow rate of 40 L·min^(-1),the mixing time predicted by the mathematical model agrees well with the measured values.The deviations between the model predictions and the measured values are in the range of about 1.3%–7.3% at the selected three monitoring locations,where the mixing time was defined as the required time when the dimensionless concentration is within 3% deviation from the bath averaged value.In addition,the circulation flow rate was 9 kg·s^(-1).When the gas blowing nozzle was horizontally rotated by either 30° or 45°,the circulation flow rate was found to be increased by about 15% compared to a conventional nozzle,due to the rotational flow formed in the up-snorkel.Furthermore,the mixing time at the monitoring point 1,2,and 3 was shortened by around 21.3%,28.2%,and 12.3%,respectively.With the nozzle angle of 30° and 45°,the averaged residence time of 128 bubbles in liquid was increased by around 33.3%.展开更多
Heavy-fuel engines are widely used in UAVs(Unmanned Autonomous Vehicles)because of their reliability and high-power density.In this study,a combustion model for an in-cylinder direct injection engine has been imple-me...Heavy-fuel engines are widely used in UAVs(Unmanned Autonomous Vehicles)because of their reliability and high-power density.In this study,a combustion model for an in-cylinder direct injection engine has been imple-mented using the AVL FIRE software.The effects of the angle of nozzle inclination on fuel evaporation,mixture distribution,and combustion in the engine cylinder have been systematically studied at 5500 r/min and consider-ing full load cruise conditions.According to the results,as the angle of nozzle inclination increases,the maximum combustion explosion pressure in the cylinderfirst increases and then it decreases.When the angle of nozzle incli-nation is less than 45°,the quality of the mixture in the cylinder and the combustion performance can be improved by increasing the angle.When the angle of nozzle inclination is greater than 45°,however,the mixture unevenness increases slightly with the angle,leading to a deterioration of the combustion performances.When the angle of nozzle inclination is between 35°and 55°,the overall combustion performance of the engine is rela-tively good.When the angle of nozzle inclination is 45°,the combustion chamber’s geometry and the cylinder’s airflow are well matched with the fuel spray,and the mixture quality is the best.Compared with 25°,the peak heat release rate increases by 20%,and the maximum combustion burst pressure increases by 5.5%.展开更多
Hydraulic jetting is a form of fracturing that involves using a high-pressure jet of water to create fractures in the reservoir rock with a nozzle serving as the central component of the hydraulic sandblasting perfora...Hydraulic jetting is a form of fracturing that involves using a high-pressure jet of water to create fractures in the reservoir rock with a nozzle serving as the central component of the hydraulic sandblasting perforation tool.In this study,the flow behavior of the nozzle is simulated numerically in the framework of a SST k-ωturbulence model.The results show that the nozzle structure can significantly influence the jet performance and related cavitation effect.Through orthogonal experiments,the nozzle geometric parameters are optimized,and the following configuration is found accordingly:contraction angle 20°,contraction segment length 6 mm,cylindrical segment diameter 6 mm,cylindrical segment length 12 mm,spread segment length 10 mm,and spread angle 55°.展开更多
This paper investigated the effects of variable jetting nozzle angles on the cross-flow suppression and heat transfer enhancement of swirl cooling in gas turbine leading edge. The swirl chamber with vertical jet nozzl...This paper investigated the effects of variable jetting nozzle angles on the cross-flow suppression and heat transfer enhancement of swirl cooling in gas turbine leading edge. The swirl chamber with vertical jet nozzles was set as the baseline, and its flow fields and heat transfer characteristics were analyzed by 3D steady state Reynolds-averaged numerical methods to reveal the mechanism of cross-flow weakening the downstream jets and heat transfer. On this basis, the flow structure on different cross sections and heat transfer characteristics of swirl chamber with variable jetting nozzle angels were compared with the baseline swirl chamber. The results indicated that for the baseline swirl chamber the circumferential velocity gradually decreased and the axial velocity gradually increased, and the cross-flow gradually formed. The cross-flow deflected the downstream jets and drawn them to the center of the chamber, thus weakening the heat transfer. For swirl chamber with variable jetting nozzle angles, the air axial velocity is axial upstream, opposite to the mainstream, so that the impact effects of cross-flow on the jets were reduced, and the heat transfer was enhanced. Furthermore, with the increase of axial velocity along the swirl chamber, the jetting nozzle angle also gradually increased, as well as the effect of cross-flow suppression, which formed a relative balance. For all swirl chambers with variable jet nozzle angles, the thermal performance factors were all larger than 1, which indicated the heat transfer was enhanced with less friction increment.展开更多
The atomizer with micro cone apertures has advantages of ultra-fine atomized droplets, low power consumption and low temperature rise. The current research of this kind of atomizer mainly focuses on the performance an...The atomizer with micro cone apertures has advantages of ultra-fine atomized droplets, low power consumption and low temperature rise. The current research of this kind of atomizer mainly focuses on the performance and its application while there is less research of the principle of the atomization. Under the analysis of the dispenser and its micro-tapered aperture's deformation, the volume changes during the deformation and vibration of the micro-tapered aperture on the dispenser are calculated by coordinate transformation. Based on the characters of the flow resistance in a cone aperture, it is found that the dynamic cone angle results from periodical changes of the volume of the micro-tapered aperture of the atomizer and this change drives one-way flows. Besides, an experimental atomization platform is established to measure the atomization rates with different resonance frequencies of the cone aperture atomizer. The atomization performances of cone aperture and straight aperture atomizers are also measured. The experimental results show the existence of the pumping effect of the dynamic tapered angle. This effect is usually observed in industries that require low dispersion and micro- and nanoscale grain sizes, such as during production of high-pressure nozzles and inhalation therapy. Strategies to minimize the pumping effect of the dynamic cone angle or improve future designs are important concerns. This research proposes that dynamic micro-tapered angle is an important cause of atomization of the atomizer with micro cone apertures.展开更多
A nozzle inclination angle and swirl combustor inside the low-tar biomass(LTB)gasifier reactor were tested and optimized to evaluate these effects on tar reduction to design tar-free producer gas.The tar reduction pro...A nozzle inclination angle and swirl combustor inside the low-tar biomass(LTB)gasifier reactor were tested and optimized to evaluate these effects on tar reduction to design tar-free producer gas.The tar reduction process is mainly based on the concept of a swirling flow created by the nozzle inclination angle,with the inclination angle of 55◦to the radial line,allowing good mixing between pyrolysis gases and gasifying agents.A separate swirl combustor has created large internal annular and reverses flow zones with the help of swirl flow,resulting in homogenized temperature inside the combustor and providing longer residence time;both have a positive effect on the combustion of mixed gasifying air-pyrolysis gases by the thermal cracking in the partial oxidation zone.Recircling ratio(RR)and combustion degree of volatiles are the two optimization parameters for evaluating the performance of NIA and swirl combustor.The result observed that outstanding tar reduction occurred in this novel system.About 86.5 and 12.8%of tar compounds are broken down in the partial oxidation zone and pyrolysis zone using the novel swirl combustor and NIA,respectively;gas outlet has observed producer gas having tar concentration of less than 1%.The optimization results reveal that a lower recycling ratio(recycle gas/gasifying air)and a higher combustion degree of volatiles perform better in biomass gasification.Finally,this system generated producer gas with the tar concentration at an extremely low level of 7.4 mg/Nm^(3)for a biomass moisture content of 9%and appeared the lower heating value of 4.6–5.1 MJ/Nm^(3).This lower tar concentration might be directly coupled with an internal combustion engine or a gas turbine for power generation.展开更多
As the width-thickness ratio of the discrete nozzle atomizer’s discrete hole greatly influences the loss of atomizing gas flow rate,the discrete nozzle atomizer was transformed into an annular slit atomizer with the ...As the width-thickness ratio of the discrete nozzle atomizer’s discrete hole greatly influences the loss of atomizing gas flow rate,the discrete nozzle atomizer was transformed into an annular slit atomizer with the same total nozzle outlet area.A numerical simulation study on the effect of various parameters on the atomization in the annular slit atomizer was carried out by coupling both the large eddy simulation(LES)and volume of fluid(VOF)model,which is based on the applicability of LES in capturing the breakup behavior of transient liquid droplets and the advantage of VOF method in directly capturing the phase interface.The simulation results showed that the increase in the atomization pressure makes the gas gain higher momentum,while the increase in the nozzle intersection angle decreases the distance between the nozzle exit and the computational domain axis.The increase in these two variables results in enhancing the gas-liquid interaction in the primary atomization zone and the formation of more aluminum droplets simultaneously.It is considered that the atomization effect becomes better when atomization pressure is 2.5 MPa,and the nozzle intersection angle is 60°.Industrial tests showed that the aluminum powder prepared by the optimized annular slit atomizer has a finer mean particle size and a higher yield of fine powder.The numerical simulation results agree well with the industrial test data of the powder particle size.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51704062)the Fundamental Research Funds for the Central Universities,China(No.N2025019)。
文摘A three-dimensional mathematical model was developed to investigate the effect of gas blowing nozzle angles on multiphase flow,circulation flow rate,and mixing time during Ruhrstahl-Heraeus(RH) refining process.Also,a water model with a geometric scale of 1:4 from an industrial RH furnace of 260 t was built up,and measurements were carried out to validate the mathematical model.The results show that,with a conventional gas blowing nozzle and the total gas flow rate of 40 L·min^(-1),the mixing time predicted by the mathematical model agrees well with the measured values.The deviations between the model predictions and the measured values are in the range of about 1.3%–7.3% at the selected three monitoring locations,where the mixing time was defined as the required time when the dimensionless concentration is within 3% deviation from the bath averaged value.In addition,the circulation flow rate was 9 kg·s^(-1).When the gas blowing nozzle was horizontally rotated by either 30° or 45°,the circulation flow rate was found to be increased by about 15% compared to a conventional nozzle,due to the rotational flow formed in the up-snorkel.Furthermore,the mixing time at the monitoring point 1,2,and 3 was shortened by around 21.3%,28.2%,and 12.3%,respectively.With the nozzle angle of 30° and 45°,the averaged residence time of 128 bubbles in liquid was increased by around 33.3%.
文摘Heavy-fuel engines are widely used in UAVs(Unmanned Autonomous Vehicles)because of their reliability and high-power density.In this study,a combustion model for an in-cylinder direct injection engine has been imple-mented using the AVL FIRE software.The effects of the angle of nozzle inclination on fuel evaporation,mixture distribution,and combustion in the engine cylinder have been systematically studied at 5500 r/min and consider-ing full load cruise conditions.According to the results,as the angle of nozzle inclination increases,the maximum combustion explosion pressure in the cylinderfirst increases and then it decreases.When the angle of nozzle incli-nation is less than 45°,the quality of the mixture in the cylinder and the combustion performance can be improved by increasing the angle.When the angle of nozzle inclination is greater than 45°,however,the mixture unevenness increases slightly with the angle,leading to a deterioration of the combustion performances.When the angle of nozzle inclination is between 35°and 55°,the overall combustion performance of the engine is rela-tively good.When the angle of nozzle inclination is 45°,the combustion chamber’s geometry and the cylinder’s airflow are well matched with the fuel spray,and the mixture quality is the best.Compared with 25°,the peak heat release rate increases by 20%,and the maximum combustion burst pressure increases by 5.5%.
基金The authors gratefully acknowledge the financial support by the Marine Economy Development Foundation of Guangdong Province“Technical Support for Stimulation and Testing of Gas Hydrate Reservoirs”(GDNRC[2022]44).
文摘Hydraulic jetting is a form of fracturing that involves using a high-pressure jet of water to create fractures in the reservoir rock with a nozzle serving as the central component of the hydraulic sandblasting perforation tool.In this study,the flow behavior of the nozzle is simulated numerically in the framework of a SST k-ωturbulence model.The results show that the nozzle structure can significantly influence the jet performance and related cavitation effect.Through orthogonal experiments,the nozzle geometric parameters are optimized,and the following configuration is found accordingly:contraction angle 20°,contraction segment length 6 mm,cylindrical segment diameter 6 mm,cylindrical segment length 12 mm,spread segment length 10 mm,and spread angle 55°.
基金This study is financially supported by the National Natural Science Foundation of China(Grant No.51876156).
文摘This paper investigated the effects of variable jetting nozzle angles on the cross-flow suppression and heat transfer enhancement of swirl cooling in gas turbine leading edge. The swirl chamber with vertical jet nozzles was set as the baseline, and its flow fields and heat transfer characteristics were analyzed by 3D steady state Reynolds-averaged numerical methods to reveal the mechanism of cross-flow weakening the downstream jets and heat transfer. On this basis, the flow structure on different cross sections and heat transfer characteristics of swirl chamber with variable jetting nozzle angels were compared with the baseline swirl chamber. The results indicated that for the baseline swirl chamber the circumferential velocity gradually decreased and the axial velocity gradually increased, and the cross-flow gradually formed. The cross-flow deflected the downstream jets and drawn them to the center of the chamber, thus weakening the heat transfer. For swirl chamber with variable jetting nozzle angles, the air axial velocity is axial upstream, opposite to the mainstream, so that the impact effects of cross-flow on the jets were reduced, and the heat transfer was enhanced. Furthermore, with the increase of axial velocity along the swirl chamber, the jetting nozzle angle also gradually increased, as well as the effect of cross-flow suppression, which formed a relative balance. For all swirl chambers with variable jet nozzle angles, the thermal performance factors were all larger than 1, which indicated the heat transfer was enhanced with less friction increment.
基金Supported by National Natural Science Foundation of China(Grant Nos.51375227,91223201)
文摘The atomizer with micro cone apertures has advantages of ultra-fine atomized droplets, low power consumption and low temperature rise. The current research of this kind of atomizer mainly focuses on the performance and its application while there is less research of the principle of the atomization. Under the analysis of the dispenser and its micro-tapered aperture's deformation, the volume changes during the deformation and vibration of the micro-tapered aperture on the dispenser are calculated by coordinate transformation. Based on the characters of the flow resistance in a cone aperture, it is found that the dynamic cone angle results from periodical changes of the volume of the micro-tapered aperture of the atomizer and this change drives one-way flows. Besides, an experimental atomization platform is established to measure the atomization rates with different resonance frequencies of the cone aperture atomizer. The atomization performances of cone aperture and straight aperture atomizers are also measured. The experimental results show the existence of the pumping effect of the dynamic tapered angle. This effect is usually observed in industries that require low dispersion and micro- and nanoscale grain sizes, such as during production of high-pressure nozzles and inhalation therapy. Strategies to minimize the pumping effect of the dynamic cone angle or improve future designs are important concerns. This research proposes that dynamic micro-tapered angle is an important cause of atomization of the atomizer with micro cone apertures.
基金Biomass Gasification Group(BGG),DTU Chemical Engineering,Technical University of Denmark to conduct this research are acknowledged thankfully.The author thanks Zsuzsa Sarossy and Kristian Estrup from DTU Chemical Engineering for performing tar samples analysis and experimental setup during all the tests,respectively.
文摘A nozzle inclination angle and swirl combustor inside the low-tar biomass(LTB)gasifier reactor were tested and optimized to evaluate these effects on tar reduction to design tar-free producer gas.The tar reduction process is mainly based on the concept of a swirling flow created by the nozzle inclination angle,with the inclination angle of 55◦to the radial line,allowing good mixing between pyrolysis gases and gasifying agents.A separate swirl combustor has created large internal annular and reverses flow zones with the help of swirl flow,resulting in homogenized temperature inside the combustor and providing longer residence time;both have a positive effect on the combustion of mixed gasifying air-pyrolysis gases by the thermal cracking in the partial oxidation zone.Recircling ratio(RR)and combustion degree of volatiles are the two optimization parameters for evaluating the performance of NIA and swirl combustor.The result observed that outstanding tar reduction occurred in this novel system.About 86.5 and 12.8%of tar compounds are broken down in the partial oxidation zone and pyrolysis zone using the novel swirl combustor and NIA,respectively;gas outlet has observed producer gas having tar concentration of less than 1%.The optimization results reveal that a lower recycling ratio(recycle gas/gasifying air)and a higher combustion degree of volatiles perform better in biomass gasification.Finally,this system generated producer gas with the tar concentration at an extremely low level of 7.4 mg/Nm^(3)for a biomass moisture content of 9%and appeared the lower heating value of 4.6–5.1 MJ/Nm^(3).This lower tar concentration might be directly coupled with an internal combustion engine or a gas turbine for power generation.
基金the financial support provided by the National Natural Science Foundation of China(U21A20317)supported by High-Performance Computing Center of Wuhan University of Science and Technology.
文摘As the width-thickness ratio of the discrete nozzle atomizer’s discrete hole greatly influences the loss of atomizing gas flow rate,the discrete nozzle atomizer was transformed into an annular slit atomizer with the same total nozzle outlet area.A numerical simulation study on the effect of various parameters on the atomization in the annular slit atomizer was carried out by coupling both the large eddy simulation(LES)and volume of fluid(VOF)model,which is based on the applicability of LES in capturing the breakup behavior of transient liquid droplets and the advantage of VOF method in directly capturing the phase interface.The simulation results showed that the increase in the atomization pressure makes the gas gain higher momentum,while the increase in the nozzle intersection angle decreases the distance between the nozzle exit and the computational domain axis.The increase in these two variables results in enhancing the gas-liquid interaction in the primary atomization zone and the formation of more aluminum droplets simultaneously.It is considered that the atomization effect becomes better when atomization pressure is 2.5 MPa,and the nozzle intersection angle is 60°.Industrial tests showed that the aluminum powder prepared by the optimized annular slit atomizer has a finer mean particle size and a higher yield of fine powder.The numerical simulation results agree well with the industrial test data of the powder particle size.