Tread Wear and Footprint Geometrical Characters of Truck Bus Radial Tires

Wear and mileage performance are the foremost performances for truck bus radial (TBR) tires. There are a lot of researches about the tire wear performance as well as the contact patch phenomenon by using finite element analysis (FEA) method or testing. But there is little published data on the correlations between the footprint geometry and the tread wear performance of tires. In this paper, an experiment on tire-ground performance of TBR tires is carried out by using Tekscan. The real-time changes of contact-area pressure distribution that occurred during the process of continuous load and unload are recorded. Three types of tires that act differently in behavior under normal usage are analyzed. A new method of researching in tire tread wear, which focuses on the geometrical characters of the footprint, is put forward. The experimental results of the three tires are described by using footprint geometrical characters. On the basis of studying the changing laws of footprint geometrical characters during the loading process and considering consumer survey and factory feedback information, the correlations between the geometrical character of footprints and tread destruction form are built. The analyzed results show that a greater contact area coefficient and a steady coefficient of contact result in a better wear performance for TBR tires. The footprint-shape coefficient changing laws in the process of loading are found to have a very good coincidence with the tread wear of the three types of tires. Tires with a smaller footprint-shape coefficient are likely to have an average tread wear while avoiding the shoulder wear first. The proposed research provides a new solution to predict tire-ground performance at the point of footprint and several useful references for improving tire design.

New Method for Monitoring Tire Pressure of Cars Based on the Tire Radial Deformation

Monitoring tire pressure of cars and signaling abnormal conditions is an important means to prevent deadly accidents. Large achievements have been gained, especially in direct tire pressure monitoring system（TPMS）. But there has been rarely research on indirect TPMS in the world. In China, the research on indirect TPMS is almost lacking. The international research on the indirect monitoring tire pressure method is mainly based on measuring and comparing the rotating speed of wheels. But it is very difficult to measure wheel rotating speed accurately because of the influence of many random factors. In this paper, the authors propose a new method in which the tire pressure can be monitored indirectly. This method can be used for tire calibration, wheel speed frequency standardization, wheel speed frequency comparison, and abnormal tire pressure determination. The pulse frequencies from wheel speed sensors of ABS are used to indicate tire deformation. Because the frequency has a relationship with tire deformation, the tire deformation reflects the tire pressure. Small sample statistics is used in the new method to increase the accuracy, and the experimental samples using the principle of the new method have been made and tested. The result of vehicle tests on road demonstrates that the method is efficient and accurate to monitor tire pressure. The research has positive potential for developing products.

Prediction of Deformation and Footprint of High-speed Rotating Radial Tires

In this research,the tire deformations due to rotation are divided into three parts:tread,belt and carcass.Tread deformation is obtained by using a rotating hollow cylinder model,belt expansion is calculated according to the laminated composite shell theory,and a formula of dynamic equilibrium profile is built to investigate carcass deformation.Moreover,a simple method is used to predict the footprint changes caused by tire deformation.Results show that a large deformation is occurring at tire shoulder,a smaller one at tread centre,and the shoulder deformations are mostly caused by carcass.Length of footprint side edges increase with tire rolling speed increasing.The predicted tread,belt,carcass deformations and footprint changes are in good agreement with finite element analysis results.The proposed method and the results will offer a helpful guidance to tire and vehicle engineers.

Prediction of Burst Pressure of a Radial Truck Tire Using Finite Element Analysis

This paper is concerned with the numerical prediction of the burst pressure of a radial truck tire. Even though relatively rare, the tire fracture or failure brings up a big accident. Especially, the tire burst or rupture is a rapid loss of inflation pressure of a truck and bus tire leading to an explosion. The tire burst pressure, under this extreme loading condition, can be predicted by identifying the pressure at which the cord breaking force of the composite materials is attained. Recently, the use of finite element analysis in tire optimal design has become widely popular. In order to determine the burst pressure of a radial truck tire, an axisymmetric finite element model has been developed using a commercial finite element code with rebar element. The numerical result shows that the bead wire among the various layers modeled the rebar element breaks off first in the radial truck tire. The finite element modeling with the rebar element on the bead wire of a radial truck tire is able to well predict the tire burst pressure identifying the pressure at which the breaking force of steel bead wires is reached. The model predictions of tire burst pressure should be correlated with test data, in which case the tire is hydro-tested to destruction. The effect of the design change with the different bead structure on the tire burst pressure is discussed.

Computation of rolling resistance caused by rubber hysteresis of truck radial tire

Applying the results of stress and strain calculated by 3D finite element model of truck radial tire 11.00R20, a MATLAB program used to compute rolling resistance of the tire caused by hysteresis rolling resistance (HRR) is worked out. The HRR distribution on different part of tire section, and the effects of speed, load, internal pressure and the width of the rim on HRR are analyzed. The analysis results showed that energy loss produced by tread rubber contributes the most part to HRR of the whole tire, and that to decrease the HRR, the hysteresis factor of the tread rubber should be reduced, and the distribution of the stress and strain on the section be optimized.

Finite Element Simulation of Radial Tire Building and Shaping Processes Using an Elasto-Viscoplastic Model

The comprehensive tire building and shaping processes are investigated through the finite element method(FEM)in this article.The mechanical properties of the uncured rubber from different tire components are investigated through cyclic loading-unloading experiments under different strain rates.Based on the experiments,an elastoviscoplastic constitutive model is adopted to describe themechanical behaviors of the uncured rubber.The distinct mechanical properties,including the stress level,hysteresis and residual strain,of the uncured rubber can all be well characterized.The whole tire building process(including component winding,rubber bladder inflation,component stitching and carcass band folding-back)and the shaping process are simulated using this constitutive model.The simulated green tire profile is in good agreement with the actual profile obtained through 3D scanning.The deformation and stress of the rubber components and the cord reinforcements during production can be obtained fromthe FE simulation,which is helpful for judging the rationality of the tire construction design.Finally,the influence of the parameter“drum width”is investigated,and the simulated result is found to be consistent with the experimental observations,which verifies the effectiveness of the simulation.The established simulation strategy provides some guiding significance for the improvement of tire design parameters and the elimination of tire production defects.

Basic Properties of Pyrolysis Carbon Black of Waste Tyres and Application of Pyrolysis Carbon Black in Transition Layer Rubber of All Steel Radial Tire

The main chemical composition of pyrolysis carbon black of waste tires is C,O,Cu,Zn and so on.The content of ash and fine powder in pyrolysis carbon black is high,and the 300%elongation stress is high.The difference between pyrolysis carbon black and furnace black N326,which is commonly used in rubber,is obvious compared with chemical property.The pyrolysis carbon black was used to replace furnace black N326 in the transition layer of all steel load Radial tire rubber through experimental study.It was found that the compression heat generation and dynamic loss(Tanδ)of the blend rubber before and after aging were obviously reduced,the elongation at break and resilience increased,while the tensile stress and tear strength decreased by 100%and 300%,but the hardness and tensile strength changed little before and after aging.According to the latest raw material price calculation,15 used tire pyrolysis carbon black instead of furnace carbon black N326 used in all steel Radial tire transition layer rubber application,excluding labor costs,electricity and equipment depreciation,a ton of blended rubber saves about$22.86 in production costs.

Prediction of Restriction Width of Carcass by Belts for Radial Tires :Theory, Experiment and Simulation

The restriction width of carcass by the belts( RWCB) as an important parameter of radial tire design has been neglected for a long time. In order to improve the accuracy and efficiency of tire profile design,the calculating method of RWCB is proposed. The equilibrium profile is calculated by geometric model and variational approach,based on it,the predicted model of RWCB is developed for tire design. Finally,four different designs of 12R22.5 tires are investigated by experiment and finite element method,which is used to validate the accuracy of the theoretical method. Results indicate that experimental and finite element analysis results are found to be in good agreement with theoretical results; linear relationships are existed between the cord length and RWCB,and also existed between the position of belt and RWCB; tires designed by the methods have smaller and more uniform displacement,so the method can be used for tire optimized design.

Design and Selection of Servomotor for Radial Aircraft Tire Secondary Molding Machine

The company Meridian Air Tire using two method molding,molding machine transmission components design selection using mitsubishi J4 series servo motor and control system.Among them,the two-segment host pitch and rotary servo motor selection is the most typical,this paper on its design ideas and selection of a detailed discussion,for manufacturers to correctly select servo motor to provide reference.

核壳结构氧化锌对天然橡胶胶料性能的影响及其在半钢子午线轮胎胎面胶中的应用

以轻质碳酸钙为载体,制备氧化锌含量(质量分数)为30%,40%,50%和60%的核壳结构氧化锌,将核壳结构氧化锌与间接法氧化锌和活性氧化锌NC105进行对比,研究核壳结构氧化锌对天然橡胶(NR)胶料性能的影响及其在半钢子午线轮胎胎面胶中的应用。结果表明,氧化锌含量50%的核壳结构氧化锌与间接法氧化锌NR硫化胶和半钢子午线轮胎胎面胶的邵尔A型硬度、拉伸强度、拉断伸长率和撕裂强度相当,核壳结构氧化锌与活性氧化锌NC105胎面胶60℃时的损耗因子相差不大。核壳结构氧化锌胶料在减少氧化锌含量的同时性能保持不变或提升,达到了减锌提质的目的。

新型改性粘土在载重子午线轮胎胎侧胶中的应用

研究新型改性粘土在载重子午线轮胎胎侧胶中的应用。结果表明:随着改性粘土用量增大,胶料的硫化速度变慢,硬度基本一致,定伸应力、拉伸强度和撕裂强度降低;改性粘土用量在5份以下对胶料耐屈挠龟裂性能影响不大;随着改性粘土用量增大,老化后胶料抗裂口增长性能提升;添加10份改性粘土的胎侧胶能满足成品轮胎耐久性能的要求。

Simulation and Experimental Study on Load-bearing Deformation Characteristics of 11R22.5 Vehicle Retreaded Tire

The finite element bearing deformation simulation was implemented on 11.00R22.5 retreaded tires by ANSYS software in the paper in order to further clarify the bearing deformation characteristics of retreaded tires and improve the performance of retreaded tires effectively.The characteristic laws of bearing radial deformation and bearing lateral deformation of retreaded tire and new tires of the same model under different working conditions were obtained through load deformation tests.The radial deformation calculation results,simulation results and measured results of retreaded tires were comparatively analyzed.The calculation formula of bearing radial deformation of retreaded tires was proposed based on the linear regression principle.The difference of bearing deformation characteristics and ground area characteristics of retreaded tires and new tires were comparatively analyzed.The results showed that the radial and lateral deformation of retreaded tires and new tires is increased with the increase of radial load when the tire pressure was constant,and the increase trend is approximately linear.The radial stiffness of retreaded tires is similar to that of new tires under certain tire pressure and low load.The radial stiffness of retreaded tires is larger than that of new tires,and the stiffness difference is increased with the increasing of load under constant tire pressure and high load.Rubber aging phenomenon in retreaded tire carcass have an impact on the bearing deformation characteristics of retreaded tires,thereby producing great impact on the remaining service life of retreaded tires.

全钢工程机械子午线轮胎胎里露线的原因分析及解决措施

分析全钢工程机械子午线轮胎胎里露线的原因,并提出解决措施。通过采取确保成型机平宽与带束层贴合鼓周长合理、缠绕机挤出胶条尺寸稳定、成型鼓扇形块周长一致、防止垫胶贴合偏歪、内衬层接头压实、合理设定硫化定型压力等措施,有效解决了胎里露线问题。

全钢工程机械子午线轮胎胎面接头开裂原因分析和解决措施

分析全钢工程机械子午线轮胎胎面接头开裂原因,并提出相应的解决措施。通过增大挤出裁刀刀刃长度和刀枕高度、胎面长度,取消胎面底层聚乙烯膜,在成型过程中使用钢丝刷将胎面接头边部打毛等措施,胎面接头开裂问题基本解决,缺陷率由最高时的15%降低至0.16%。

14.00R24NHS港口专用全钢工程机械子午线轮胎的设计

介绍14.00R24NHS港口专用全钢工程机械子午线轮胎的设计。结构设计:外直径1410 mm,断面宽368 mm,行驶面宽度320 mm,行驶面弧度高20 mm,胎圈着合宽度274 mm,胎圈着合直径610 mm,断面水平轴位置(H1/H2)0.7391,胎面采用块状花纹,花纹深度64 mm,花纹饱和度72.2%,花纹周节数28。施工设计:胎面采用3层结构,胎体采用3+9+15×0.225ST钢丝帘线,带束层采用4层结构,其中1^(#)带束层采用3+9+15×0.175+0.15HT钢丝帘线,2^(#)和3^(#)带束层采用3+9+15×0.220+0.15HT钢丝帘线,4^(#)带束层采用3×7×0.20HE钢丝帘线,采用一次法两鼓/三鼓成型机成型,采用蒸锅式硫化机硫化。成品性能试验结果表明,成品轮胎的充气外缘尺寸、物理性能和静负荷性能均达到国家标准及相应设计要求。

国产溶聚丁苯橡胶在半钢子午线轮胎胎面胶中的应用

研究国产溶聚丁苯橡胶(SSBR)在半钢子午线轮胎胎面胶中的应用。结果表明:与进口SSBR胶料相比,国产SSBR胶料的硫化特性、物理性能和耐臭氧老化性能相当;成品轮胎的高速性能和耐久性能均通过测试,滚动阻力相当,干地和湿地制动性能可满足使用要求,且可降低材料成本。

苯酚-甲醛树脂MK-95在轿车子午线轮胎胎体胶中的应用

研究苯酚-甲醛树脂MK-95(简称MK-95)在轿车子午线轮胎胎体胶中的应用。结果表明:MK-95不含游离间苯二酚和其他添加剂,其软化点和挥发分含量低于间苯二酚-甲醛树脂;在胎体胶中以MK-95等量替代间苯二酚-甲醛树脂,胶料的硫化特性、物理性能、动态力学性能和粘合性能相当,成品轮胎的高速、耐久和路试性能均达到要求。

全钢子午线轮胎胎圈复合填充胶预口型的优化设计

对全钢子午线轮胎胎圈复合填充胶预口型进行优化设计。结果表明:选择合适的材料可以增大预口型表面的硬度,从而改善预口型使用中磕碰、磨损的现象;扩大预口型流胶口出口尺寸能够使其匹配多种规格的口型板,从而大幅减少预口型的更换;调整预口型流胶口贴合面尺寸,可以解决半部件贴合面容易出现气泡、脱层的问题。使用改进后的预口型可以缩短轮胎生产时间,提高轮胎半成品质量。

生物基白炭黑和生物基油在全钢载重子午线轮胎胎面胶中的应用

研究生物基白炭黑和生物基油在全钢载重子午线轮胎胎面胶中的应用。结果表明:使用生物基油等量代替环烷油,胶料的硫化速度略加快,300%定伸应力降低,耐切割、耐低温和耐迁移性能提高,生热略增大,耐磨性能基本相当;在同样采用生物基油的情况下,使用生物基白炭黑等量代替沉淀法白炭黑,胶料的硫化特性、生热、耐磨和耐切割性能相当,但耐疲劳性能明显降低。

高驱动性能315/80R22.5无内胎全钢载重子午线轮胎的设计

介绍高驱动性能315/80R22.5无内胎全钢载重子午线轮胎的设计。结构设计:外直径1093 mm,断面宽314 mm,行驶面宽度275 mm,行驶面弧度高7.5857 mm,胎圈着合直径570.5 mm,胎圈着合宽度240.8 mm,断面水平轴位置(H_(1)/H_(2))0.91,胎面采用泥地+雪地花纹,花纹深度24 mm,花纹饱和度66.41%,花纹周节数54。施工设计:采用双复合胎面,1^(#)和2^(#)带束层采用0.37+6×0.32ST钢丝帘线,0°带束层由3根3×0.7×0.20HE钢丝帘线压延成的冠带条围绕2#带束层缠绕而成,3#带束层采用5×5.30HI钢丝帘线,胎体采用0.22+6+11×0.205ST钢丝帘线,采用一次法成型机成型、双模蒸锅式硫化机硫化。成品轮胎性能试验结果表明,轮胎的充气外缘尺寸、强度性能、耐久性能和胎圈耐久性能均满足相应设计和标准要求。