Chemical flooding is one of the most efficient methods for Enhanced Oil Recovery (EOR). This study demonstrates the efficiency of mixing different concentrations of Ionic Liquid (IL), 1-Ethyl-3-Methyl-Imidazolium Acet...Chemical flooding is one of the most efficient methods for Enhanced Oil Recovery (EOR). This study demonstrates the efficiency of mixing different concentrations of Ionic Liquid (IL), 1-Ethyl-3-Methyl-Imidazolium Acetate ([EMIM][Ac]), with Weyburn brine to improve a medium oil recovery, Weyburn oil, from an unconsolidated sand pack sample at room conditions. Effects of Slug Size (SS), IL + brine slug initiation time, and combining IL with alkali on the Recovery Factor (RF) were investigated. This study showed that the optimum concentration of ([EMIM][AC]) was 1000 ppm and the most efficient injection time of the chemical slug was at the beginning of the flooding procedure (as secondary flooding mode). In addition, it was proved that the potential of injecting a slug of IL + brine is much better than that of introducing a slug of alkali + brine. Besides, the combination of IL and alkali (AIL) resulted in better RF than injecting either of them alone. Finally, the Surface Tension (SFT), pH, wettability alteration, and viscosity of the displacing phases were measured.展开更多
Laboratory experiments were conducted to simulate oil weathering process, a medium to long term weathering process for 210-d, using samples collected from five different oil resources. Based on relative deviation and ...Laboratory experiments were conducted to simulate oil weathering process, a medium to long term weathering process for 210-d, using samples collected from five different oil resources. Based on relative deviation and repeatability limit analysis about indexes of these samples, the results show there had been significant changes in diagnostic ratios among the initial and weathered samples of different oils during this process. Changes of selected n-alkane diagnostic ratios of all oil samples displayed more obviously than diagnostic ratios of terpanes,steranes and PAHs in this process. Almost all selected diagnostic ratios of terpanes, steranes and PAHs can be efficiently used in tracking sources of hydrocarbon pollution, differentiating from the n-alkane diagnostic ratios.In these efficient diagnostic ratios, only four ratios maintained good stability in the weathering processes and are more suitable because their relative deviation（RSD） are lower than 5%.展开更多
The properties of medium density fibreboard (MDF) made from oil palm trunk (OPT) as affected by refining pressure and preheating time were investigated. The OPT chips were refined in the MDF pilot plant by using four ...The properties of medium density fibreboard (MDF) made from oil palm trunk (OPT) as affected by refining pressure and preheating time were investigated. The OPT chips were refined in the MDF pilot plant by using four refining pressures (2, 4, 6 and 8 bar) and four different preheating time (100, 200, 300 and 400 seconds). The refined fibres were blended with 10% of urea formaldehyde with a board target density of 720 kg/m3. MDF boards were evaluated based on European Standard EN 622-5:2006 for thickness swelling (TS), internal bonding (IB), modulus of rupture (MOR) and modulus of elasticity (MOE). Analysis of variance (ANOVA) was used to analyze the significance of the factors. The results from this study indicated that refining pressure and preheating time are significant factors for all MDF properties. Low refining pressure and preheating time produced higher TS, lower MOR and MOE with poor bonding than those boards prepared from fibres refined at higher refining pressure and longer preheating time. OPT fibre treated with 8 bar produced good swelling resistance but detrimental on mechanical properties of the finish board. 6 bar steam pressure offered the highest value of mechanical properties (MOE, MOR and IB). Boards from intermediate refining condition (6 bar and 300 seconds) were found the better board properties having 14.58%, 0.73 N/mm2, 38 N/mm2 and 3597 N/mm2 for TS, IB, MOR and MOE respectively.展开更多
Considering the influence of quadratic gradient term and medium deformation on the seepage equation, a well testing interpretation model for low permeability and deformation dual medium reservoirs was derived and esta...Considering the influence of quadratic gradient term and medium deformation on the seepage equation, a well testing interpretation model for low permeability and deformation dual medium reservoirs was derived and established. The difference method was used to solve the problem, and pressure and pressure derivative double logarithmic curves were drawn to analyze the seepage law. The research results indicate that the influence of starting pressure gradient and medium deformation on the pressure characteristic curve is mainly manifested in the middle and late stages. The larger the value, the more obvious the upward warping of the pressure and pressure derivative curve;the parameter characterizing the dual medium is the crossflow coefficient. The channeling coefficient determines the time and location of the appearance of the “concave”. The smaller the value, the later the appearance of the “concave”, and the more to the right of the “concave”.展开更多
文摘Chemical flooding is one of the most efficient methods for Enhanced Oil Recovery (EOR). This study demonstrates the efficiency of mixing different concentrations of Ionic Liquid (IL), 1-Ethyl-3-Methyl-Imidazolium Acetate ([EMIM][Ac]), with Weyburn brine to improve a medium oil recovery, Weyburn oil, from an unconsolidated sand pack sample at room conditions. Effects of Slug Size (SS), IL + brine slug initiation time, and combining IL with alkali on the Recovery Factor (RF) were investigated. This study showed that the optimum concentration of ([EMIM][AC]) was 1000 ppm and the most efficient injection time of the chemical slug was at the beginning of the flooding procedure (as secondary flooding mode). In addition, it was proved that the potential of injecting a slug of IL + brine is much better than that of introducing a slug of alkali + brine. Besides, the combination of IL and alkali (AIL) resulted in better RF than injecting either of them alone. Finally, the Surface Tension (SFT), pH, wettability alteration, and viscosity of the displacing phases were measured.
基金The National Natural Science Foundation of China under contract No.41206089Project of on-site sediment microbial remediation of public area of central Bohai Sea,North China Sea Branch of State Oceanic Administration under contract No.QDZC20150420-002Program of Science and Technology Service Network Initiative,Chinese Academy of Sciences under contract No.KFJ-EW-STS-127
文摘Laboratory experiments were conducted to simulate oil weathering process, a medium to long term weathering process for 210-d, using samples collected from five different oil resources. Based on relative deviation and repeatability limit analysis about indexes of these samples, the results show there had been significant changes in diagnostic ratios among the initial and weathered samples of different oils during this process. Changes of selected n-alkane diagnostic ratios of all oil samples displayed more obviously than diagnostic ratios of terpanes,steranes and PAHs in this process. Almost all selected diagnostic ratios of terpanes, steranes and PAHs can be efficiently used in tracking sources of hydrocarbon pollution, differentiating from the n-alkane diagnostic ratios.In these efficient diagnostic ratios, only four ratios maintained good stability in the weathering processes and are more suitable because their relative deviation（RSD） are lower than 5%.
文摘The properties of medium density fibreboard (MDF) made from oil palm trunk (OPT) as affected by refining pressure and preheating time were investigated. The OPT chips were refined in the MDF pilot plant by using four refining pressures (2, 4, 6 and 8 bar) and four different preheating time (100, 200, 300 and 400 seconds). The refined fibres were blended with 10% of urea formaldehyde with a board target density of 720 kg/m3. MDF boards were evaluated based on European Standard EN 622-5:2006 for thickness swelling (TS), internal bonding (IB), modulus of rupture (MOR) and modulus of elasticity (MOE). Analysis of variance (ANOVA) was used to analyze the significance of the factors. The results from this study indicated that refining pressure and preheating time are significant factors for all MDF properties. Low refining pressure and preheating time produced higher TS, lower MOR and MOE with poor bonding than those boards prepared from fibres refined at higher refining pressure and longer preheating time. OPT fibre treated with 8 bar produced good swelling resistance but detrimental on mechanical properties of the finish board. 6 bar steam pressure offered the highest value of mechanical properties (MOE, MOR and IB). Boards from intermediate refining condition (6 bar and 300 seconds) were found the better board properties having 14.58%, 0.73 N/mm2, 38 N/mm2 and 3597 N/mm2 for TS, IB, MOR and MOE respectively.
文摘Considering the influence of quadratic gradient term and medium deformation on the seepage equation, a well testing interpretation model for low permeability and deformation dual medium reservoirs was derived and established. The difference method was used to solve the problem, and pressure and pressure derivative double logarithmic curves were drawn to analyze the seepage law. The research results indicate that the influence of starting pressure gradient and medium deformation on the pressure characteristic curve is mainly manifested in the middle and late stages. The larger the value, the more obvious the upward warping of the pressure and pressure derivative curve;the parameter characterizing the dual medium is the crossflow coefficient. The channeling coefficient determines the time and location of the appearance of the “concave”. The smaller the value, the later the appearance of the “concave”, and the more to the right of the “concave”.
