Effects of nitrate concentration in interstitial water on the bioremediation of simulated oil-polluted shorelines

Nutrient addition has been proved to be an effective strategy to enhance oil biodegradation in marine shorelines. To determine the optimal range of nutrient concentrations in the bioremediation of oil-polluted beaches, nitrate was added to the simulated shoreline models in the initial concentration of 1, 5 and 10 mg/L. Whenever the NO3-N concentration declined to 70% of its original value, additional nutrients were supplemented to maintain a certain range. Results showed adding nutrients increased the oil biodegradation level, the counts of petroleum degrading bacteria （PDB） and heterotrophic bacteria （HB）, and the promoted efficiency varied depending on the concentration of nitrate. Oil degradation level in 5 mg/L （NO3-N） group reached as much as 84.3% accompanied with the consistently highest counts of PDB; while in l mg/L group oil removal efficiency was only 35.2%, and the numbers of PDB and HB were relatively low compared to the other groups supplemented with nutrients. Although counts of HB in the 10 mg/L group were remarkable, lower counts of PDB resulted in poorer oil removal efficiency （70.5%） compared to 5 mg/L group. Furthermore, it would need more NO3-N （0.371 mg） to degrade 1 mg diesel oil in the 10 mg/L group than in the 5 mg/L group （0.197 mg）. In conclusion, Nitrate concentration in 5 mg/L is superior to l and 10 mg/L in the enhancement of diesel oil biodegradation in simulated shorelines.

Effect of HCO_3^- concentration on CO_2 corrosion in oil and gas fields

The effect of HCO3^- concentration on CO2 corrosion was investigated by polarization measurement of potentiodynamic scans and weight-loss method, Under the conditions of high pressure and high temperature, the corrosion rate of steel X65 decreased with the increase of HCO3^- concentration, while pH of solution increased. SEM, EDS, and XRD results of the corrosion scales indir cated that the typical FeCO3 crystallite was found at low HCO3^- concentration but Ca（Fe,Mg）（CO3）2 was found at high HCO3^- con- centration. Ca^2＋ and Mg^2＋ are precipitated preferential to Fe^2＋ at high pH value. Potentiodynamic polarization curves showed that the cathodic current density decreases with the increase of HCO3^- concentration at low HCO3^- concentration. When the HCO3^- concentration reaches 0.126 mol/L, increasing HCO3^- concentration promotes cathodic reactions. Anodic behavior is an active process at low HCO3^- concentration and the anodic current density decreases with the increase of HCO3^- concentration. An evident active-passive behavior is exhibited in anodic process at 0.126 mol/L HCO3^-.

Rapid accuracy determining DNA purity and concentration in heavy oils by spectrophotometry methods

DNA analysis is the core of biotechnology applied in petroleum resources and engineering. Traditionally accurate determination of DNA purity and concentration by spectrometer is the first and critical step for downstream molecular biology research. In this study, three different spectrophotometry methods, BPM, NDTT and NPMTTZ were compared for their performance in determining DNA concentration and purity in 32 oil samples, and molecule methods like quantitative real-time PCR (qPCR) and high-throughput sequence were also performed to help assess the accuracy of the three methods in determining DNA concentration and purity. For ordinary heavy oil (OHO), extra heavy oil (EHO) and super heavy oil (SHO), the characteristics of high viscosity (η), density (ρ) and resin plus asphaltene content will affect the DNA extraction and UV determination. The DNA concentration was decreased as density increased: OHO (11.46 ± 18.34 ng/μL), EHO (6.68 ± 9.67 ng/μL) and SHO (6.20 ± 7.83 ng/μL), and the DNA purity was on the reverse: OHO (1.31 ± 0.27), EHO (1.54 ± 0.20), and SHO (1.83 ± 0.32). The results suggest that spectrophotometry such as BPM and NPMTTZ are qualitatively favorite methods as the quick non-consumable methods in determining DNA concentration and purity of medium oil and heavy oil.

The Relationship between Nigerian Bonnylight Crude Oil-Induced Hypoglycaemia and Endogenous Serum Insulin Concentration in Male Wistar Rats: The Role of Antioxidant Vitamins C and E

The relationship between Nigerian Bonny Light crude oil (NBLCO) induced hypoglycaemia and endogenous serum insulin concentration;the role of antioxidant vitamin C or E supplementation was the focus of this study. Forty adult male Wistar rats were randomly divided into group I, which served as the control, group II, which was oral gavaged 6 ml/kg of NBLCO, groups III and IV, which were in addition to 6 ml/kg of NBLCO supplemented with 9 ml/kg and 1 mg/kg of vitamin E or C, respectively for 28 days. Results showed that NBLCO significantly (p < 0.05) lower body weight and food intake compared with control. These effects exerted by NBLCO were however significantly (p < 0.05) reversed by vitamin E or C supplementation. The NBLCO significantly (p < 0.05) reduced fasting blood glucose (FBG) when compared with control, the antioxidant vitamins supplementation significantly (p < 0.05) reversed the crude oil effect. The mean serum insulin level in NBLCO, vitamin E or C supplemented groups is not significantly different from the control. There was no significant correlation between FBG and fasting serum insulin concentrations in all the groups on day 28. It has been demonstrated in this study that direct oral ingestion of crude oil (NBLCO) could reduce food intake, body weight and cause hypoglycemia;the hypoglycemia may not be a function of serum insulin concentration. Interestingly, the hazardous effects of NBLCO could be ameliorated with antioxidant vitamin C or E supplementation.

Spectral Transmittance of Di-methyl Silicon Oil as a Heat Transfer Material for Concentrator Solar Cells

The accelerated life test was carded out to investigate the change of spectral transmittance of di-methyl silicon oil and the effects on the electrical performance of silicon solar cell. The di-methyl silicon oil samples be- fore and after accelerated life test were analyzed by FT-IR, GC-MS and LC-MS. The ring compounds and linear compounds with larger molecular weight were detected. The spectral transmittance of di-methyl silicon oil de- creased because the chromophore and auxochrome of the products made a sunlight receive decrease on the surface of the solar celt, and resulted in the reduction of cell performance. According to the decrease of spectral transmit- tance of di-methyl silicon oil, two recovery methods were proposed. The results showed that extraction was supe- rior to vacuum distillation in recovering the aged di-methyl silicon oil.

The Feasibility of ASP Flooding with Low Alkali Concentration in Heterogeneous Reservoirs

In this paper, as far as the ASP flooding in the pilot area of Daqing oilfield is concerned, the effect of apparent viscosity of ASP solution on enhanced oil recovery have been studied by comparison of experiments on artificial heterogeneous cores with on natural cores. The results showed that the decrease in the concentration of alkali could increase the apparent viscosity of ASP solutions, namely, the apparent viscosity increased and the IFT couldn’t get ultra low, and the oil recovery efficiency by ASP solution with a reasonably lower concentration of alkali was not less than that with a higher concentration of alkali and ultra low IFT. The experiments with models having impermeable interlayers between adjacent layers, and by means of “co-injection and separate production” showed that the ASP solution with a higher viscosity and a lower alkali concentration was more beneficial to starting-up medium and low permeability layers and enhancing total oil recovery. Therefore, to heterogeneous reservoir, as factors of affecting oil recovery, the apparent viscosity may be more important than the ultralow IFT. Furthermore, on the premise that the concentration of surfactant and the concentration of polymer keep constant, ASP flooding with low alkali concentration not only enlarges the selectable range of surfactants and decreases the cost of ASP flooding, but also solves the problem of alkali scales. Finally, a dynamic absorption experiment was performed with a 05 meter long linked-up natural core to determine alkali wastage in formation. The result being accord with the application case in the pilot confirmed that it was not necessary to add the alkali too much in ASP flooding from a new direction.

Methane in soil gas and its transfer to the atmosphere in the Yakela condensed gas field in the Tarim Basin,Northwest China

In this study, by analyzing CH4 concentration and 613CCH4 in soil-gas profiles, the potentials of CH4 gas transfer from ground to atmosphere were studied at four representative sectors in the Yakela condensed gas field in the Tarim Basin, Xinjiang, China. These are： 1） the oil-gas interface sector, 2） fault sector, 3） oil-water interface sector, 4） an external area. Variation in CH4 in soil-gas profiles showed that CH4 microseepage resulted from the migration of subsurface hydrocarbon from deep-buried reservoirs to the earth＇s surface. It was found that CH4 from deep-buried reservoirs could migrate upwards to the surface through faults, fissures and permeable rocks, during which some CH4 was oxidized and the unoxidized methane remained in the soil or was emitted into the atmosphere. The lowest level of CH4 at the soil-gas profile was found at the CH4 gas-phase equilibrium point at which the CH4 migration upwards from deep-buried reservoirs and the CH4 diffusion downwards from the atmosphere met. The 613CcH4 and ethane, propane in soil gas exhibited thermogenic characteristics, suggesting the occurrence of CH4 microseepage from deep-buried reservoirs. A linear correlation analysis between CH4 concentrations in soil gas and temperature, moisture, pH, Eh, Ec and particle size of soil indicated that both soil Eh and soil temperature could affect CH4 concentration in soil gas while soil pH could indirectly influence soil methanotrophic oxidation via impacting soil Eh.

Status, trends and enlightenment of global oil and gas development in 2021

By analyzing the distribution of global oil and gas fields and the reasons why some oil and gas fields are not in production, the distribution characteristics of oil and gas remaining recoverable reserves and their year-on-year changes, the distribution characteristics of oil and gas production and their year-on-year changes, and the development potential of oil and gas to be tapped in 2021, this paper sorts out systematically the current status and characteristics of global oil and gas development, summaries the major trends of global oil and gas development, puts forward enlightenment for international oil and gas cooperation. In 2021, oil and gas fields were widely distributed, the number of non-producing oil and gas fields was large;the whole oil and gas remaining recoverable reserves declined slightly, unconventional oil and gas remaining recoverable reserves dropped significantly;the overall oil and gas production continuously increased, the outputs of key resource-host countries kept year-on-year growth;undeveloped oilfields had abundant reserves and great development potential. Combined with global oil and gas geopolitics, oil and gas industry development trends, oil and gas investment intensity, and the tracking and judgment of hotspot fields, the major trends of global oil and gas development in 2021 are summarized. On this basis, the four aspects of enlightenment and suggestions for international oil and gas cooperation and development strategies are put forward: attach great importance to the obligation of marine abandonment to ensure high-quality and long-term benefit development of offshore oil and gas;adhere to the principle of not going to dangerous and chaotic places, strengthen the concentration of oil and gas assets, and establish multi stable supply bases;based on the multi-scenario demand of natural gas, realize the transformation from integrated collaboration to full oil and gas industry chain development;increase the acquisition of high-quality large-scale assets, and pay attention to the continuous optimization of the shareholding ratio of projects at different stages.

Efficiency of Ionic Liquid 1-Ethyl-3-Methyl-Imidazolium Acetate ([EMIM][Ac]) in Enhanced Medium Oil Recovery

Chemical flooding is one of the most efficient methods for Enhanced Oil Recovery (EOR). This study demonstrates the efficiency of mixing different concentrations of Ionic Liquid (IL), 1-Ethyl-3-Methyl-Imidazolium Acetate ([EMIM][Ac]), with Weyburn brine to improve a medium oil recovery, Weyburn oil, from an unconsolidated sand pack sample at room conditions. Effects of Slug Size (SS), IL + brine slug initiation time, and combining IL with alkali on the Recovery Factor (RF) were investigated. This study showed that the optimum concentration of ([EMIM][AC]) was 1000 ppm and the most efficient injection time of the chemical slug was at the beginning of the flooding procedure (as secondary flooding mode). In addition, it was proved that the potential of injecting a slug of IL + brine is much better than that of introducing a slug of alkali + brine. Besides, the combination of IL and alkali (AIL) resulted in better RF than injecting either of them alone. Finally, the Surface Tension (SFT), pH, wettability alteration, and viscosity of the displacing phases were measured.

Low Frequency Dispersion Mechanism of Dielectric Response for Oil-paper Insulation Diagnosis

Both the real part and imaginary part of complex permittivity approximately have a log-linear frequency dependency at low fre- quencies, especially at ultra-low frequencies under conditions of different moisture concentrations and temperatures, which is recognized as the low frequency dispersion (LFD). In order to explain this dispersion, a new mechanism of dielectric response of LFD of oil-paper insula- tion is proposed. A simplified one-dimensional mathematical model of concentration polarization carrier caused by slow migration is developed and solved, which indicates that ion mobility is closely related to the size of gap and the adsorption capacity of cellulose molecu- lar chains to ions. A stochastic statistical model of the carrier mobility induced LFD is also developed. Moreover, actual tests under 50 °C and 2% moisture content were put forward, as well as simulations with according current waveforms. The simulation results agreed well with the experimental data in that concentration polarization of carriers caused by slow migration is the probable cause of low frequency dispersion of dielectric response for oil-paper insulation diagnosis.

The Global Research Progress of Enzymatic Processing of Oils with Omega 3 Polyunsaturated Fatty Acids

This paper has reviewed that Omega 3 polyunsaturated fatty acids (PUFAs), as an essential fatty acids (EFAs), mainly come from fish oil of marine products, has positive effects on treatment and/or prevention of several diseases. In this review, the recent developments by 2019 in the field of enzymatic modification of oils rich in omega 3 PUFAs have summarized. Several different products, such as structured lipids with a variety of FA compositions, nutritional aspects, omega 3 PUFA concentrates and phospholipids,have discussed from the point of process technology as well as possible applications. Enhancing omega 3 PUFA content in diet involves a number of strategies aiming to modify the content of such FAs in fats and oils. Due to the mild reaction conditions used, especially the lipase specificity, the position as well as content of omega 3 PUFAs in lipid molecules being of importance from the point of bioavailability, enzymatic processing of omega 3 PUFA oil is safe, efficient and preferred over chemical treatments.

Analysis of OPEC’s Monopoly in Crude Oil Market

This article briefly and historically reviews the polices of the Organization of Petroleum Exporting Countries （OPEC） and analyzes the factors that facilitate or hinder OPEC＇s monopoly in the crude oil market. The industrial concentration ratio is chosen to measure OPEC＇s monopoly power based on the data from 1986 to 2004. It is concluded that OPEC possesses a long-standing cartel foundation and a rather strong monopoly in the world crude oil market. At the same time, there are unstable factors that influence and even weaken OPEC＇s monopoly.

The Study of Electromagnetic Stress Testing Method on Oil-Gas Pipelines Based on WT

This paper proposes an effective method for early diagnosis (stress concentrating) of the oil-gas pipeline. Based on the principle of electromagnetic induction Faraday, we have designed and realized the nondestructive testing system for stress concentration area of ferromagnetic materials by means of the research of metal materials inverse magnetostrictive effect mechanism. The system changes the influence degree of the stress in ferromagnetic materials’ magnetic conductance to the corresponding voltage array by using discrete wavelet analysis method to process the data, in which not only the measuring accuracy is improved, but also the stress concentration is more directly reflected. The experiments confirm that the electromagnetic stress testing method is feasible and valid.

Mechanisms and experimental research of ion-matched waterflooding to enhance oil recovery in carbonate reservoirs: A case of Cretaceous limestone reservoirs in Halfaya Oilfield, Middle East

Based on systematically summarizing the achievements of previous ion-matched waterflooding researches,the diversity and synergy of oil recovery enhancement mechanisms and the interaction between mechanisms are examined according to two classification standards,and the influence of behaviors of different ions on different mechanisms and oil displacement efficiency are investigated.Ionic strength is proposed to characterize the behavior differences of univalent and divalent ions,the relationships between ionic strength,effective concentration,and mechanisms are established to characterize the ion behavior behind various mechanisms,and evaluate the performance of ion-matched injection water.The mechanisms of enhancing oil recovery by ion-matched waterflooding include:(1)The ion-matched water can reduce the ion strength and match the ion composition of formation water,thereby reducing the difference between the effective concentration of univalent ions and divalent ions on the surface of carbonate rocks,and improving the effective concentration of potential determining ions(especially SO42-).(2)It can improve wettability,oil-water interface properties,pore structure and physical properties of the reservoir,and finally enable the establishment of a new ionic equilibrium conducive to waterflooding while breaking the original equilibrium.In this study,experiments such as relative permeability curve,interfacial tension,and core-flooding were carried out on carbonate core samples from the Cretaceous Mishrif Formation reservoirs in Halfaya Oilfield,Middle East,a method for injection water evaluation was established and the injection water suitable for these reservoirs was selected:6 times diluted seawater.Compared with ordinary seawater,oil displacement efficiency can be increased by more than 4.60%and compared with the optimum dilution of formation water,oil displacement efficiency can be increased by 3.14%.

Uptake of B,Co and Ni by Plants from Oil Contaminated Soil Capped with Peat

Plant uptake of contaminants provides vital information for the reclamation of large area of contaminated soils.A field experiment was conducted using four plant species growing in four kinds of oil contaminated soils to estimate the uptake of organic and inorganic contaminants by plants from the oil contaminated soils.The experiment showed that the concentrations of some selected elements,such as B,Co and Ni in plants growing in the oil contaminated soils were significantly higher than those in plants growing in the uncontaminated control soil.The accumulation of metals in plants increased with plant biomass;however,the removal of metals by plants from the oil contaminated soils was not practical.

Relationship between Microbial Community Characteristics and Flooding Efficiency in Microbial Enhanced Oil Recovery

Microbial enhanced oil recovery (MEOR) is the research focus in the field of energy development as an environmentally friendly and low cost technology. MEOR can bes divided into indigenous microbial oil recovery and exogenous microbial oil recovery. The ultimate goal of indigenous microbial flooding is to enhance oil recovery via stimulation of specific indigenous microorganisms by injecting optimal nutrients. For studying the specific rule to activate the indigenous community during the long-term injection period, a series of indigenous displacement flooding experiments were carried out by using the long-core physical simulation test. The experimental results have shown that the movement of nutrients components (i.e., carbon/nitrogen/phosphorus) differed from the consumption of them. Moreover, there was a positive relationship between the nutrients concentration and bacteria concentration once observed in the produced fluid. And the trend of concentration of acetic acid was consistent with that of methanogens. When adding same activators, the impacts of selective activators to stimulate the indigenous microorganisms became worse along with the injection period, which led to less oil recovery efficiency.

Adsorption of Natural Surfactant on Sandstone in Enhanced Oil Recovery: Isotherms and Kinetics Studies

In chemical enhanced oil recovery, surfactants are injected into the reservoir with the intention to lower interfacial tension (IFT) between the water and oil phases, and thereby bring about efficient displacement of oil. However, the adsorption of the surfactants to reservoir rock surfaces leads to the loss and reduction in concentration of the surfactants, which in turn reduces the overall efficiency of the oil recovery process, with attendant financial losses. In this work, the adsorption of Quillaja Saponaria (QS), a novel, natural, non-ionic surfactant, on crushed sandstone reservoir rock is investigated. X-ray diffraction (XRD) study of clean sandstone particles has been undertaken to determine the main components present in the sand particles. The conductivity method was used to measure CMC and the surfactant concentrations in aqueous solutions. Batch adsorption experiments were used to determine the amount of QS adsorbed on rock surface. Equilibrium conditions were reached after almost 5 days. From the results of the study, the Langmuir isotherm model is more suited for predicting the adsorption behaviour of QS on sandstone. The kinetic adsorption of QS obeys the pseudo-second order model. This study is particularly relevant in surfactant selection for chemical EOR processes.

The Mechanism and Usage for Enhanced Oil Recovery by Chemotaxis of Bacterium BS2

Due to its chemotaxis, the motion ability of bacterium BS2 is very strong, and under the microscope, the distribution grads of bacterium concentration can be seen at the oil-water interface.During the experiments in glass box, it can be observed, with eyes, because of the chemotaxis, that muddy gets thicker and thicker at the interface gradually, and it is measured there, from sampling, that the bacterium concentration is 10 9 cells/mL, pH value 4.4 and the concentration of bio-surfactant 2.87%; The microbial oil-displacement experiments are carried out in emulational network models, and the oil-displacement mechanism by the bacterium and its metabolizing production is studied. And, during oil-displacement experiments in the gravel-input glass models, because of the profile control of thalli and the production, the sweep area of subsequent waterflood becomes wider, which can be seen with eyes and the recovery is enhanced by 13.6%. Finally, the successful field test is introduced in brief: the ratio of response producers is 85.7%, and the water-cut degrades by 6.4%, while 20038 t oil has increased in accumulative total in 2 years.

复合磨损套管爆裂失效机理及剩余强度预测

超深井、水平井、大位移井等复杂油气井服役工况异常恶劣,套管复合磨损严重,将对井筒完整性构成巨大威胁,且磨损套管剩余强度难以精准预测。为此,基于塔里木盆地塔中北坡顺南区块501井套管磨损数据及P110管材应力—应变本构关系,建立了充分考虑钻杆本体和接头联合造成的磨损模式、夹角、磨损重叠深度及磨损深度的复合磨损套管有限元力学模型,并开展了多种复合磨损模式下套管弹塑性变形、屈服、裂纹萌生、扩展及爆裂行为模拟,得到了不同复合磨损套管应力分布、剩余抗内压屈服强度及爆裂强度。研究结果表明:(1)月牙夹角在0°~90°时,应力干涉削弱应力集中,月牙夹角在90°~180°时,应力干涉增强应力集中,这种交互作用机制导致磨损套管剩余强度随着月牙夹角增加而先增加后降低;(2)裂纹萌生并起始于等效应力最大的位置即磨损月牙中心,并垂直于最大环向应力沿径向从套管内壁向外壁扩展,且裂纹一旦萌生,裂纹将迅速扩展并发生爆裂失效;(3)灰色关联度分析确定了复合磨损套管剩余强度对磨损深度、月牙夹角、复合磨损形式、月牙重叠深度的敏感性,分析结果表明磨损深度是决定套管剩余强度的主控因素。结论认为,该认识为套管强度设计与优化提供了技术参考,并对准确预测复合磨损套管剩余强度和确保井筒安全及完整性具有重要意义。

煤与油气协调开采物理相似模拟研究

针对煤与油气协调开采中,煤层开发扰动油气圈闭层稳定性及油气井筒的问题,利用二维模拟试验开展了煤与油气开采地层响应规律研究;采用“先油气后煤炭”的开采工序,得到了煤与油气各覆岩层的应力演化、破断变形特征及油气井筒变形破坏规律。研究结果表明:若油气层高强度抽采至采收完毕,模型整体结构未出现明显扰动,仅层间岩层局部存在应力集中现象,而此时对煤层进行开采会对下方200 m处油气层产生一定扰动;采动初期,油气层采收边界上方应力不断上升,煤层底板存在应力传递现象,煤层顶板无明显应力变化,初次扰动范围为100 m,二次扰动范围为75 m;当进入充分采动阶段,油气层采收边界上方应力集中沿水平向右侧偏移,煤层底板相继经历应力集中-卸压的过程,层间岩层结构趋于稳定,岩层运移程度逐渐向煤层顶部附近岩层转移,说明煤层采动作用在叠置资源协调开采过程中对整体岩层稳定性影响程度较大,应着重关注煤层开采对煤与油气协调开采中的影响;覆岩内井筒主要破坏模式为剪切变形破坏,位于工作面中心处的井筒下侧则发生拉伸-剪切变形破坏,应着重关注工作面中心处的井筒防护。