Fabrication of magnetically responsive anti-fouling and easy-cleaning nanofiber membrane and its application for efficient oil-water emulsion separation

The magnetically responsive anti-fouling nanofiber membrane(MRANM)was fabricated for efficient oilwater emulsion separation,which could be cleaned using oscillating magnetic field.MRANM was prepared by grafting superparamagnetic Fe_(3)O_(4) nanoparticles onto the surface of electrospun polyacrylonitrile nanofiber membrane(PANM).Compared with PANM,the water contact angle of MRANM decreased from 104°to 0°,indicating that the hydrophilicity of the membrane was significantly improved.For the emulsions of hexadecane,octane and rapeseed oil,the separation efficiency was 98.04%,96.59%and 92.67%,respectively.After the treatments in oscillating magnetic field,the separation efficiency kept above 95%after 8 times recycling,which indicated that the MRANM had good regenerability and reusability.The as-fabricated membrane with magnetic responsiveness facilitated an effective method for solving the membrane fouling problem during practical applications of separation high viscosity oil-water emulsion.

Experimental investigation of the effects of various parameters on viscosity reduction of heavy crude by oil-water emulsion

The effects of water content, shear rate, temperature, and solid particle concentration on viscosity reduction （VR） caused by forming stable emulsions were investigated using Omani heavy crude oil. The viscosity of the crude oil was initially measured with respect to shear rates at different temperatures from 20 to 70℃. The crude oil exhibited a shear thinning behavior at all the temperatures. The strongest shear thinning was observed at 20℃. A non-ionic water soluble surfactant （Triton X-100） was used to form and stabilize crude oil emulsions. The emulsification process has significantly reduced the crude oil viscosity. The degree of VR was found to increase with an increase in water content and reach its maximum value at 50 % water content. The phase inversion from oil- oil emulsion occurred at 30 in-water emulsion to water-in- % water content. The results indicated that the VR was inversely proportional to temperature and concentration of silica nanoparticles. For water-in-oil emulsions, VR increased with shear rate and eventually reached a plateau at a shear rate of around 350 s^-1. This was attributed to the thinning behavior of the continuous phase. The VR of oil-in-water emulsions remained almost constant as the shear rate increased due to the Newtonian behavior of water, the continuous phase.

Influence of Experimental Factors on Preparing Oil-Water Emulsion

The infuence of experimental factors on preparing Oil-Water (o/w) emulsion arc studied- These factors include the amount of emulsifier, the ratio of oil to water, the intensity of agitation, the temperature, and the time of emulsification. The best experimental factors have been found in the process of Preparing emulsion using SP-4 as emulsifier.

Effect of sodium starch octenyl succinate-based Pickering emulsion on the physicochemical properties of hairtail myofibrillar protein gel subjected to multiple freeze-thaw cycles

A Pickering emulsion based on sodium starch octenyl succinate(SSOS)was prepared and its effects on the physicochemical properties of hairtail myofibrillar protein gels(MPGs)subjected to multiple freeze-thaw(F-T)cycles were investigated.The whiteness,water-holding capacity,storage modulus(G')and texture properties of the MPGs were significantly improved by adding 1%-2%Pickering emulsion(P<0.05).Meanwhile,Raman spectral analysis demonstrated that Pickering emulsion promoted the transformation of secondary structure,enhanced hydrogen bonds and hydrophobic interactions,and promoted the transition of disulfide bond conformation from g-g-g to g-g-t and t-g-t.At an emulsion concentration of 2%,theα-helix content decreased by 10.37%,while theβ-sheet content increased by 7.94%,compared to the control.After F-T cycles,the structure of the MPGs was destroyed,with an increase in hardness and a decrease in whiteness and water-holding capacity,however,the quality degradation of MPGs was reduced with 1%-2%Pickering emulsion.These findings demonstrated that SSOS-Pickering emulsions,as potential fat substitutes,can enhance the gel properties and the F-T stability of MPGs.

Oil-in-water nanoemulsions loaded with lycopene extracts encapsulated by spray drying:Formulation,characterization and optimization

Lycopene is very susceptible to degradation once released from the protective chromoplast environment.In this study,oil-in-water(O/W)nanoemulsions coupled with spray drying technology were applied for the encapsulation and stabilization of lycopene extracted from tomato waste.Tomato extract was obtained by ultrasound-assisted extraction.Nanoemulsions were prepared by a high-speed rotor stator using isopropyl myristate as the oil phase and Pluronic F-127 as the emulsifier for the aqueous external phase.The effect of emulsification process parameters was investigated.Spray drying of the produced emulsions was attempted to obtain a stabilized dry powder after the addition of a coating agent.The effect of different coating agents(maltodextrin,inulin,gum arabic,pectin,whey and polyvinylpyrrolidone),drying temperature(120-170℃),and feed flow rate(3-9 ml·min^(-1))on the obtained particles was evaluated.Results revealed that the emulsion formulation of 20/80(O/W)with 1.5%(mass fraction)of Pluronic F-127 as stabilizer in the aqueous phase resulted in a stable nanoemulsion with droplet sizes in the range of 259-276 nm with a unimodal and sharp size distribution.The extract in the nanoemulsion was well protected at room temperature with a degradation rate of lycopene of about 50%during a month of storage time.The most stable emulsions were then processed by spray drying to obtain a dry powder.Spray drying was particularly successful when using maltodextrin as a coating agent,obtaining dried spherical particles with mean diameters of(4.87±0.17)μm with a smooth surface.The possibility of dissolving the spray dried powder in order to repristinate.The original emulsion was also successfully verified.

Insights into the enhancement of food flavor perception:strategies,mechanism and emulsion applications

The core drivers of the modern food industry are meeting consumer demand for tasty and healthy foods.The application of food flavor perception enhancement can help to achieve the goals of salt-and sugar-reduction,without compromising the sensory quality of the original food,and this has attracted increasing research attention.The analysis of bibliometric results from 2002 to 2022 reveals that present flavor perception enhancement strategies(changing ingredient formulations,adding salt/sugar substitutes,emulsion delivery systems)are mainly carry out based on sweetness,saltiness and umami.Emulsion systems is becoming a novel research foci and development trends of international food flavor perception-enhancement research.The structured design of food emulsions,by using interface engineering technology,can effectively control,or enhance the release of flavor substances.Thus,this review systematically summarizes strategies,the application of emulsion systems and the mechanisms of action of food flavor perception-enhancement technologies,based on odor-taste cross-modal interaction(OTCMI),to provide insights into the further structural design and application of emulsion systems in this field.

Fluid property identification of the Lower Cretaceous reservoirs with complex oil-water contacts in Deseo Basin,Chad

Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,complex oil-water contact within and faint responses of the oil zone,which causes the lower accuracy of reservoir fluid property identification with conventional mudlogging and wirelogging techniques.Applying the geochemical logging,fluorescent logging,mud logging and cutting logging technology,in combination with formation test data,this paper distinguishes the crude oil types,analyzes the logging response characteristics of oil zone after water washing,and establishes the interpretation charts and parameter standards for reservoir fluid properties.The crude oil can be divided into two types,namely viscous-heavy and thin-light,based on total hydrocarbon content and component concentration tested by mud logging,features of pyrolysis gas chromatogram and fluorescence spectroscopy.The general characteristics of oil layers experienced water washing include the decrease of total hydrocarbon content and component concentration from mud logging,the decrease of S1 and PS values from geochemical logging,the decrease of hydrocarbon abundance and absence of some light components in pyrolysis gas chromatogram,and the decrease of fluorescence area and intensity from fluorescence logging.According to crude oil types,the cross plots of S1 versus peak-baseline ratio,and the cross plots of rock wettability versus fluorescence area ratio are drawn and used to interpret reservoir fluid property.Meanwhile,the standards of reservoir fluid parameter are established combining with the parameters of PS and the parameters in above charts,and comprehensive multiparameter correlation in both vertical and horizontal ways is also performed to interpret reservoir fluid property.The application in the Doseo Basin achieved great success,improving interpretation ability of fluid property in the reservoir with complex oil-water contact,and also provided technical reference for the efficient exploration and development of similar reservoirs.

Anti-abrasion collagen fiber-based membrane functionalized by UiO-66-NH_(2)with ultra-high efficiency and stability for oil-in-water emulsions separation

Membrane separation strategies offer promising platform for the emulsion separation.However,the low mechanical strength of membrane separation layers and the trade-off between separation flux and efficiency present significant challenges.In this study,we report a CFM@UiO-66-NH_(2)membrane with high separation flux,efficiency and stability,through utilizing a robust anti-abrasion collagen fiber membrane(CFM)as the multifunctional support and UiO-66-NH_(2)by an in-situ growth as the separation layer.The high mechanical strength of the CFM compensated for the weakness of the separation layer,while the charge-breaking effect of UiO-66-NH_(2),along with the size sieving of its constituent separating layers and the capillary effect of the collagen fibers,contributed to the potential for efficient separation.Additionally,the CFM@UiO-66-NH_(2)membrane exhibited superhydrophilic properties,making it suitable for separating oil-in-water microemulsions and nanoemulsions stabilized by anionic surfactants.The membrane demonstrated remarkable separation efficiencies of up to 99.960%and a separation flux of370.05 L·m^(-2)·h^(-1).Moreover,it exhibits stability,durability,and abrasion resistance,maintaining excellent separation performance even when exposed to strong acids and alkalis without any damage to its structure and performance.After six cycles of reuse,it achieved a separation flux of 417.97 L·m^(-2)·h^(-1)and a separation efficiency of 99.747%.Furthermore,after undergoing 500 cycles of strong abrasion,the separation flux remained at 124.39 L·m^(-2)·h^(-1),with a separation efficiency of 99.992%.These properties make it suitable for the long-term use in harsh operating environments.We attribute these properties to the electrostatic effect resulting from the amino group on UiO-66-NH_(2)and its in-situ growth on the CFM,which forms a size-screening separation layer.Our work highlights the potential of the CFM@UiO-66-NH_(2)membrane as an environmentally friendly size-screening material for the efficient emulsion wastewater separation.

Pickering emulsion transport in skeletal muscle tissue:A dissipative particle dynamics simulation approach

Lymph node targeting is a commonly used strategy for particulate vaccines,particularly for Pickering emulsions.However,extensive research on the internal delivery mechanisms of these emulsions,especially the complex intercellular interactions of deformable Pickering emulsions,has been surprisingly sparse.This gap in knowledge holds significant potential for enhancing vaccine efficacy.This study aims to address this by summarizing the process of lymph-node-targeting transport and introducing a dissipative particle dynamics simulation method to evaluate the dynamic processes within cell tissue.The transport of Pickering emulsions in skeletal muscle tissue is specifically investigated as a case study.Various factors impacting the transport process are explored,including local cellular tissue environmental factors and the properties of the Pickering emulsion itself.The simulation results primarily demonstrate that an increase in radial repulsive interaction between emulsion particles can decrease the transport efficiency.Additionally,larger intercellular gaps also diminish the transport efficiency of emulsion droplet particles due to the increased motion complexity within the intricate transport space compared to a single channel.This study sheds light on the nuanced interplay between engineered and biological systems influencing the transport dynamics of Pickering emulsions.Such insights hold valuable potential for optimizing transport processes in practical biomedical applications such as drug delivery.Importantly,the desired transport efficiency varies depending on the specific application.For instance,while a more rapid transport might be crucial for lymph-node-targeted drug delivery,certain applications requiring a slower release of active components could benefit from the reduced transport efficiency observed with increased particle repulsion or larger intercellular gaps.

Characterization of Flame Retardancy and Oil-Water Separation Capacity of Superhydrophobic Silylated Melamine Sponges

A silylated melamine sponge(SMS)was prepared by two simple steps,namely,immersion and dehydration of a melamine sponge coated with methyltrichlorosilane.The silylated structure of SMS was characterized by FT-IR(Fourier-transform infrared)spectroscopy,SEM(Scanning electron microscopy)and in terms of water contact angles.Its oil-water absorption and separation capacities were measured by FT-IR and UV-visible spectrophoto-metry.The experimental results have shown that oligomeric silanol covalently bonds by Si-N onto the surface of melamine sponge skeletons.SMS has shown superhydrophobicity with a water contact angle exceeding 150°±1°,a better separation efficiency with regard to diesel oil(by 99.31%(wt/wt%)in oil-water mixture and even up to 99.99%(wt/wt%)for diesel oil in its saturated aqueous solution.Moreover,SMS inherited the intrinsicflame retardancy of the melamine sponge.In general,SMS has shown superhydrophobicity,high porosity,excellent selectivity,remarkable recyclability,and better absorption capacity for various oils and organic solvents,and a high separation efficiency for oil in saturated aqueous solutions.

Hyperspectral remote sensing identification of marine oil emulsions based on the fusion of spatial and spectral features

Marine oil spill emulsions are difficult to recover,and the damage to the environment is not easy to eliminate.The use of remote sensing to accurately identify oil spill emulsions is highly important for the protection of marine environments.However,the spectrum of oil emulsions changes due to different water content.Hyperspectral remote sensing and deep learning can use spectral and spatial information to identify different types of oil emulsions.Nonetheless,hyperspectral data can also cause information redundancy,reducing classification accuracy and efficiency,and even overfitting in machine learning models.To address these problems,an oil emulsion deep-learning identification model with spatial-spectral feature fusion is established,and feature bands that can distinguish between crude oil,seawater,water-in-oil emulsion(WO),and oil-in-water emulsion(OW)are filtered based on a standard deviation threshold–mutual information method.Using oil spill airborne hyperspectral data,we conducted identification experiments on oil emulsions in different background waters and under different spatial and temporal conditions,analyzed the transferability of the model,and explored the effects of feature band selection and spectral resolution on the identification of oil emulsions.The results show the following.(1)The standard deviation–mutual information feature selection method is able to effectively extract feature bands that can distinguish between WO,OW,oil slick,and seawater.The number of bands was reduced from 224 to 134 after feature selection on the Airborne Visible Infrared Imaging Spectrometer(AVIRIS)data and from 126 to 100 on the S185 data.(2)With feature selection,the overall accuracy and Kappa of the identification results for the training area are 91.80%and 0.86,respectively,improved by 2.62%and 0.04,and the overall accuracy and Kappa of the identification results for the migration area are 86.53%and 0.80,respectively,improved by 3.45%and 0.05.(3)The oil emulsion identification model has a certain degree of transferability and can effectively identify oil spill emulsions for AVIRIS data at different times and locations,with an overall accuracy of more than 80%,Kappa coefficient of more than 0.7,and F1 score of 0.75 or more for each category.(4)As the spectral resolution decreasing,the model yields different degrees of misclassification for areas with a mixed distribution of oil slick and seawater or mixed distribution of WO and OW.Based on the above experimental results,we demonstrate that the oil emulsion identification model with spatial–spectral feature fusion achieves a high accuracy rate in identifying oil emulsion using airborne hyperspectral data,and can be applied to images under different spatial and temporal conditions.Furthermore,we also elucidate the impact of factors such as spectral resolution and background water bodies on the identification process.These findings provide new reference for future endeavors in automated marine oil spill detection.

Numerical Simulation of Oil-Water Two-Phase Flow in Low Permeability Tight Reservoirs Based on Weighted Least Squares Meshless Method

In response to the complex characteristics of actual low-permeability tight reservoirs,this study develops a meshless-based numerical simulation method for oil-water two-phase flow in these reservoirs,considering complex boundary shapes.Utilizing radial basis function point interpolation,the method approximates shape functions for unknown functions within the nodal influence domain.The shape functions constructed by the aforementioned meshless interpolation method haveδ-function properties,which facilitate the handling of essential aspects like the controlled bottom-hole flow pressure in horizontal wells.Moreover,the meshless method offers greater flexibility and freedom compared to grid cell discretization,making it simpler to discretize complex geometries.A variational principle for the flow control equation group is introduced using a weighted least squares meshless method,and the pressure distribution is solved implicitly.Example results demonstrate that the computational outcomes of the meshless point cloud model,which has a relatively small degree of freedom,are in close agreement with those of the Discrete Fracture Model(DFM)employing refined grid partitioning,with pressure calculation accuracy exceeding 98.2%.Compared to high-resolution grid-based computational methods,the meshless method can achieve a better balance between computational efficiency and accuracy.Additionally,the impact of fracture half-length on the productivity of horizontal wells is discussed.The results indicate that increasing the fracture half-length is an effective strategy for enhancing production from the perspective of cumulative oil production.

Influence of the Powder on the Properties of the Liquid Crystal Emulsions

The purpose of study was to evaluate the effect of four powder including titanium dioxide,bismuth oxychloride,silica,and kaolin on the properties of the liquid crystal emulsions.The results show that the addition of titanium dioxide and bismuth oxychloride had no obvious effect on the liquid crystal structure.In addition,the addition of Kaolin and silica have an effect on the stability of the liquid crystal structure.Sensory evaluation and Texture analyzer results shown that the addition of titanium dioxide and bismuth oxychloride had no obvious effect on the spreadability of liquid crystal system.The addition of silica and Kaolin was increased the hardness and adhesive of the liquid crystal system.Rheological experiments shown that the kaolin system had lower structural stability.the system with titanium dioxide,bismuth oxychloride,and silica has good stability.This paper provides data support for the application of powders in the formulation of liquid crystal system,which aims to provide a data basis for the preparation and applications of liquid crystal emulsion.

Experimental investigation on using CO_(2)/H_(2)O emulsion with high water cut in enhanced oil recovery

CO_(2) emulsions used for EOR have received a lot of interest because of its good performance on CO_(2)mobility reduction.However,most of them have been focusing on the high quality CO_(2) emulsion(high CO_(2) fraction),while CO_(2) emulsion with high water cut has been rarely researched.In this paper,we carried out a comprehensive experimental study of using high water cut CO_(2)/H_(2)O emulsion for enhancing oil recovery.Firstly,a nonionic surfactant,alkyl glycosides(APG),was selected to stabilize CO_(2)/H_(2)O emulsion,and the corresponding morphology and stability were evaluated with a transparent PVT cell.Subsequently,plugging capacity and apparent viscosity of CO_(2)/H_(2)O emulsion were measured systematically by a sand pack displacement apparatus connected with a 1.95-m long capillary tube.Furthermore,a high water cut(40 vol%) CO_(2)/H_(2)O emulsion was selected for flooding experiments in a long sand pack and a core sample,and the oil recovery,the rate of oil recovery,and the pressure gradients were analyzed.The results indicated that APG had a good performance on emulsifying and stabilizing CO_(2) emulsion.An inversion from H_(2)O/CO_(2) emulsion to CO_(2)/H_(2)O emulsion with the increase in water cut was confirmed.CO_(2)/H_(2)O emulsions with lower water cuts presented higher apparent viscosity,while the optimal plugging capacity of CO_(2)/H_(2)O emulsion occurred at a certain water cut.Eventually,the displacement using CO_(2)/H_(2)O emulsion provided 18.98% and 13.36% additional oil recovery than that using pure CO_(2) in long sand pack and core tests,respectively.This work may provide guidelines for EOR using CO_(2) emulsions with high water cut.

Progress in Preparation and Application of Gel-Emulsions

Compared to conventional emulsions, gel-emulsions have a higher internal phase volume fraction, unique structures and properties, higher viscosity, and tunable internal structures. These advantages make them widely applicable in the cosmetics industry, food industry, aerospace, and biomedicine, with significant potential in the development of new materials and high-performance products. The factors affecting the stability of gel-emulsions, as well as the types of stabilizers required for their preparation (including solid particles, surfactants, and small molecule gelators), and the corresponding preparation methods (including the one-step method, two-step method, and phase inversion method) are reviewed in this article. The applications of gel-emulsions in porous materials, food, cosmetics, and stimuli-responsive materials are introduced, and future research directions are also discussed.

Effects of Different Heavy Crude Oil Fractions on the Stability of Oil-in-water Emulsions —— Isolation of functional fractions from heavy crude oil and study of their properties

The functional fractions (acid, basic, amphoteric and neutral fractions) are isolated from the Liaohe Du-84 heavy crude oil and Shengli Gudao Kenxi heavy crude oil by ion-exchange chromatography, but the conventional fractions (saturates, aromatics, resins and asphaltenes) are also isolated from the heavy crude oil. These components have been characterized by spectroscopic methods (FT-IR), namely acid number, basic nitrogen number, ultimate analysis and molecular weight measurements using vapor pressure osmometry (VPO). The ion-exchange chromatography method based on separation by a functional group induces a little change on the nature of the crudes and reasonable mass balances can be easily obtained.

Ultrasonic method for measuring water holdup of low velocity and high-water-cut oil-water two-phase flow

Oil reservoirs with low permeability and porosity that are in the middle and late exploitation periods in China＇s onshore oil fields are mostly in the high-water-cut production stage.This stage is associated with severely non-uniform local-velocity flow profiles and dispersed-phase concentration（of oil droplets） in oil-water two-phase flow,which makes it difficult to measure water holdup in oil wells.In this study,we use an ultrasonic method based on a transmission-type sensor in oil-water two-phase flow to measure water holdup in lowvelocity and high water-cut conditions.First,we optimize the excitation frequency of the ultrasonic sensor by calculating the sensitivity of the ultrasonic field using the finite element method for multiphysics coupling.Then we calculate the change trend of sound pressure level attenuation ratio with the increase in oil holdup to verify the feasibility of the employed diameter for the ultrasonic sensor.Based on the results,we then investigate the effects of oildroplet diameter and distribution on the ultrasonic field.To further understand the measurement characteristics of the ultrasonic sensor,we perform a flow loop test on vertical upward oilwater two-phase flow and measure the responses of the optimized ultrasonic sensor.The results show that the ultrasonic sensor yields poor resolution for a dispersed oil slug in water flow（D OS/W flow）,but the resolution is favorable for dispersed oil in water flow（D O/W flow） and very fine dispersed oil in water flow（VFD O/W flow）.This research demonstrates the potential application of a pulsed-transmission ultrasonic method for measuring the fraction of individual components in oil-water two-phase flow with a low mixture velocity and high water cut.

Properties of Compound Systems of Paraffin Wax Emulsion and Copper Azole and Treated Wood

[Objective]Preservation and waterproof treatment are two crucial parts in wood protection, which can not only extend the service time, but also expand the application range of wood products. [Method] This work combined CA with paraffin wax emulsion to treat wood samples, and basic properties of the compound system, such as stability （storage stability and centrifugal stability）, particle size and pH val-ue, and water repel ency （water absorption, shrinkage and swel ing） of treated sam-ples were investigated. [Result and Conclusion] 1） the compound systems of CA and paraffin latex had a favorable miscibility and stability; 2） compared with untreated wood, CA-treated samples showed poor water repel ing properties, whereas samples treated with the compound systems indicated an obvious reduction in water absorp-tion, and the shrinkage and swel ing of them were improved as wel .

Experimental measurements of water content in crude oil emulsions by terahertz time-domain spectroscopy

We measured the water content （0.01% 0.25% w/w） in crude oil emulsions using terahertz time-domain spectroscopy （THz-TDS）. To improve the precision and range of the measurements, we used 1 and 10 mm thick quartz cells. The experiments were performed at 20 ℃ and the THz wave was transmitted vertically to the samples and detected on the other side. The experimental results suggest linear relation for the THz absorption coefficient and the water content of the crude oil emulsions in the observed range. The linear dependence facilitates high-precision measurements of the water content of crude oil. This suggests the potential of THz-TDS in determining the water concentration in crude oil and borehole fluid identification.

STUDY ON SYNTHESIS OF AMPHOTERIC POLYACRYLAMIDE IN INVERSE EMULSION

Amphoteric polyacrylamide was prepared first by the copolymerization of acrylamide with sodium acrylate and then through Mannich reaction.The copolymerization was carried out with a redox initiation system using the method of inverse emulsion polymerization.In this paper the reaction conditions and factors that affect emulsion stability were studied.Experiments show that a stable latex can be obtained under the following conditions:anionic degree is five percent,the ratio among acrylamide,formaldehyde and dimethylamine is 1∶1∶1.2,reaction temperature is 45 ℃,reaction time lasts four hours,and pH equals 5.0.The amphoteric copolymer has a higher molecular weight and cationic degree,so it is an ideal filler retention and drainage aid in paper making.