Analysis of mechanical strengths of extreme line casing joint considering geometric, material, and contact nonlinearities

To address the challenges associated with difficult casing running,limited annular space,and poor cementing quality in the completion of ultra-deep wells,the extreme line casing offers an effective solution over conventional casings.However,due to its smaller size,the joint strength of extreme line casing is reduced,which may cause failure when running in the hole.To address this issue,this study focuses on the CST-ZTΦ139.7 mm×7.72 mm extreme line casing and employs the elastic-plastic mechanics to establish a comprehensive analysis of the casing joint,taking into account the influence of geometric and material nonlinearities.A finite element model is developed to analyze the forces and deformations of the extreme line casing joint under axial tension and external collapse load.The model investigates the stress distribution of each thread tooth subjected to various tensile forces and external pressures.Additionally,the tensile strength and crushing strength of the extreme line casing joint are determined through both analytical and experimental approaches.The findings reveal that,under axial tensile load,the bearing surface of each thread tooth experiences uneven stress,with relatively high equivalent stress at the root of each thread tooth.The end thread teeth are valuable spots for failure.It is observed that the critical fracture axial load of thread decreases linearly with the increase of thread tooth sequence.Under external pressure,the circumferential stress is highest at the small end of the external thread,leading to yield deformation.The tensile strength of the joint obtained from the finite element model exhibits a relative error of less than 7%compared to the analytical and experimental values,proving the reliability of the finite element model.The tensile strength of the joint is 3091.9 k N.Moreover,in terms of anti-collapse capability,the joints demonstrate higher resistance to collapse compared to the casing body,which is consistent with the test results where the pipe body experiences collapse and failure while the joints remain intact during the experiment.The failure load of the casing body under external collapse pressure is 87.4 MPa.The present study provides a basic understanding of the mechanical strengths of extreme line casing joint.

Automated deep learning system for power line inspection image analysis and processing: architecture and design issues

The continuous growth in the scale of unmanned aerial vehicle (UAV) applications in transmission line inspection has resulted in a corresponding increase in the demand for UAV inspection image processing. Owing to its excellent performance in computer vision, deep learning has been applied to UAV inspection image processing tasks such as power line identification and insulator defect detection. Despite their excellent performance, electric power UAV inspection image processing models based on deep learning face several problems such as a small application scope, the need for constant retraining and optimization, and high R&D monetary and time costs due to the black-box and scene data-driven characteristics of deep learning. In this study, an automated deep learning system for electric power UAV inspection image analysis and processing is proposed as a solution to the aforementioned problems. This system design is based on the three critical design principles of generalizability, extensibility, and automation. Pre-trained models, fine-tuning (downstream task adaptation), and automated machine learning, which are closely related to these design principles, are reviewed. In addition, an automated deep learning system architecture for electric power UAV inspection image analysis and processing is presented. A prototype system was constructed and experiments were conducted on the two electric power UAV inspection image analysis and processing tasks of insulator self-detonation and bird nest recognition. The models constructed using the prototype system achieved 91.36% and 86.13% mAP for insulator self-detonation and bird nest recognition, respectively. This demonstrates that the system design concept is reasonable and the system architecture feasible .

Temperature-Triggered Hardware Trojan Based Algebraic Fault Analysis of SKINNY-64-64 Lightweight Block Cipher

SKINNY-64-64 is a lightweight block cipher with a 64-bit block length and key length,and it is mainly used on the Internet of Things(IoT).Currently,faults can be injected into cryptographic devices by attackers in a variety of ways,but it is still difficult to achieve a precisely located fault attacks at a low cost,whereas a Hardware Trojan(HT)can realize this.Temperature,as a physical quantity incidental to the operation of a cryptographic device,is easily overlooked.In this paper,a temperature-triggered HT(THT)is designed,which,when activated,causes a specific bit of the intermediate state of the SKINNY-64-64 to be flipped.Further,in this paper,a THT-based algebraic fault analysis(THT-AFA)method is proposed.To demonstrate the effectiveness of the method,experiments on algebraic fault analysis(AFA)and THT-AFA have been carried out on SKINNY-64-64.In the THT-AFA for SKINNY-64-64,it is only required to activate the THT 3 times to obtain the master key with a 100%success rate,and the average time for the attack is 64.57 s.However,when performing AFA on this cipher,we provide a relation-ship between the number of different faults and the residual entropy of the key.In comparison,our proposed THT-AFA method has better performance in terms of attack efficiency.To the best of our knowledge,this is the first HT attack on SKINNY-64-64.

Stylistic Analysis on English On-line Chat

Based on the fact that on-line chat has become the most developing language form in the information age, this article point out the stylistic features of on-line English chat. Though in written language form, such language is spoken language in nature, thus it is worthwhile to analyze this special phaenomenon in lexical and grammatical level.

Molecular analysis and anticancer properties of two identified isolates,Fusarium solani and Emericella nidulans isolated from Wady El-Natron soil in Egypt against Caco-2(ATCC) cell line

Objective:To characterize,identify and investigate the anticancer properties of two new soil fungal isolates,Emericella nidulansand Fusarium solani isolated from Wady El-Natron in Egypt against colon cancer Caco-2(ATCCj cell line.Methods:Soil sample was cultured and two strains were chosen for morphological and phenotypical characterization.Partial sequences of the 18s rRNA gene and the internal transcribed spacer region ITS of the two isolates were amplified by PCR.Phylogenetic tree construction and analysis of the resulted multiple sequences from the two fugal isolates were also carried out.In vitro anticancer activity of the two strains was done against colon Caco-2 cancer cell line.Reverse transcription — PCR was carried out to detect level of expression of p53 in Caco-2 cell line.Results:HF.I displayed morphological and genotypic characteristics most similar to that of Fusarium solani while HF.2 was most similar to Emericella nidulans with high similarity of 99%and 97%respectively.The multiple sequence alignment of the two fungal isolates showed that,the maximum identical conserved domains in the 18s rRNA genes were identified with the nucleotide regions of Slst to 399th base pairs,88th to 525th base pairs respectively.While those in the ITS genes were identified with the nucleotide regions of 88th to 463rd and Slst to 274th.The two isolates showed IC<sub>50 value with（6.24±5.21） and（9.84±0.36） μ g/mL) concentrations respectively at 28h.Reverse transcription- PCR indicated that these cells showed high level of expression for p53 mRNA.Conclusions:The morphology and molecular analysis identified HF.1 and HF.2 to be Fusarium solani and Emericella nidulans;new isolates of anticancer producing fungi from Wady El-Natroon city in Egypt.Treatment with the two isolates caused P53 expression in Caco-2 cell line.These two isolates can be used as an anticancer agents.

Protein profile of human hepatocarcinoma cell line SMMC-7721:Identification and functional analysis

AIM： TO investigate the protein profile of human hepatocarcinoma cell line SMMC-7721, to analyze the specific functions of abundant expressed proteins in the processes of hepatocarcinoma genesis, growth and metastasis, to identify the hepatocarcinoma-specific biomarkers for the early prediction in diagnosis, and to explore the new drug targets for liver cancer therapy. METHODS： Total proteins from human hepatocarcinoma cell line SMMC-7721 were separated by two-dimensional electrophoresis （2DE）. The silver-stained gel was analyzed by 2DE software Image Master 2D Elite. Interesting protein spots were identified by peptide mass fingerprinting based on matrix-assisted laser desorption/ ionization time-of-flight mass spectrometry （MALDI-TOF-MS） and database searching. RESULTS： We obtained protein profile of human hepatocarcinoma cell line SMMC-7721. Among the twenty-one successfully identified proteins, mitofilin, endoplasmic reticulum protein ERp29, ubiquinol-cytochrome C reductase complex core protein I, peroxisomal enoyl CoA hydratase, peroxiredoxin-4 and probable 3-oxoacid CoA transferase 1 precursor were the six novel proteins identified in human hepatocarcinoma cells or tissues. Specific functions of the identified heat-shock proteins were analyzed in detail, and the results suggested that these proteins might promote tumorigenesis via inhibiting cell death induced by several cancer-related stresses or via inhibiting apoptosis at multiple points in the apoptotic signal pathway. Other identified chaperones and cancer-related proteins were also analyzed.CONCLUSION： Based on the protein profile of SMMC-7721 cells, functional analysis suggests that the identified chaperones and cancer-related proteins have their own pathways to contribute to the tumorigenesis, tumor growth and metastasis of liver cancer. Furthermore, proteomic analysis is indicated to be feasible in the cancer study.

Near Crack Line Elastic-Plastic Analysis for an Infinite Plate Loaded by a Pair of Point Shear Forces

The near crack line analysis method was used to investigate a crack loaded by a pair of point shear forces in an infinite plate in an elastic-perfectly plastic solid. The analytical solution was obtained, that is the elastic-plastic fields near crack line and law that the length of the plastic zone along the crack line is varied with external loads. The results are sufficiently precise near the crack line and are not confined by small scale yielding conditions.

DEVELOPMENT AND APPLICATIONS OF AN ON-LINE THERMAL NEUTRON PROMPT-GAMMA ELEMENT ANALYSIS SYSTEM

This paper introduces the principles, instrumentation, implementation, and industrial applications of an on- line thermal neutron prompt- gamma element analysis system (using a 252Cf neutron source, Am- Be neutron source, or neutron generator). The energy resolution of the system at the H prompt- gamma full- energy photopeak (2.22325 MeV) is 3.6 keV. The concentration measurement error of A12O3, Fe2O3, CaO and SiO2 is ±0.3%,±0.1%.±0.4% and ±0.4%, respectively.The system has been tested on- site at both the Shandong and the Zhengzhou Aluminum Works. Our preliminary on- site measurements confirm that the stability, reliability, measurement range, and accuracy of the system can meet the requirements of the aluminum production process. Facilitation of this measurement at aluminum plants is expected to reduce plant costs by over 3 million dollars annually through reduced energy consumption, more rapid qualification of pulps being mixed during the production process, and in reduced labor costs.

A Comparative Analysis of the New -3(-n) - 1 Remer Conjecture and a Proof of the 3n + 1 Collatz Conjecture

This scientific paper is a comparative analysis of two mathematical conjectures. The newly proposed -3(-n) - 1 Remer conjecture and how it is related to and a proof of the more well known 3n + 1 Collatz conjecture. An overview of both conjectures and their respective iterative processes will be presented. Showcasing their unique properties and behavior to each other. Through a detailed comparison, we highlight the similarities and differences between these two conjectures and discuss their significance in the field of mathematics. And how they prove each other to be true.

Comprehensive Evaluation of New Self-cultivated Sugarcane Lines by Grey Relational Analysis

The grey relational analysis( GRA) was used to evaluate the 10 sugarcane lines by 13 main agronomic characters. The result showed that the grey correlation degree of self-cultivated lines GNY08- 320(0. 7502),GNY08- 336(0. 7409),GNY08- 186(0. 7369),and GNY08- 225(0. 7277) were higher than ROC22(CK),so the 4 lines can be further tested,and the others were worse than CK that should be further observed or eliminated.

AN APPLICATION OF TOPOLOGICAL ANALYSIS TO STUDYING THE THREE-DIMENSIONAL FLOW IN CASCADES;PART I—TOPOLOGICAL RULES FOR SKIN-FRICTION LINES AND SECTION STREAMLINES

Based on the working of Lighthill and Hunt et al., in the present paper the author has established the topological rules adapting to analysing the skin-friction lines and the section streamlines in cascades. These rules are (1) for a rotor cascade without shroud band, the total number of nodal points equals that the saddle points on the skin-friction line vector fields in eachpitch range; (2) for an annular or straight cascade with no-clearances at blade ends, the total number of saddle points is two more than that of nodal points on the skin-friction line fields in a pitch; (3) the total number of saddles in the secondary flow fields on cross-sections in cascade is one less than that of nodes; (4) in the section streamline vector fields on a meridian surface penetrating a flow passage, and on leading and trailing edge sections, the total number of nodes is equal to that of saddles; (5) on the streamline vector fields of a blade-to-blade surface, the total number of nodes is one less than that of saddles.

The selection and stability analysis of stable and high Taxol-producing cell lines from Taxus cuspidata

In this study to screen for stable, high Taxolproducing cell lines（CL5, CL12, and CL21） of Taxus cuspidata, stem tissues were used to induce calli, which were then subcultured nine times to establish suspension cell cultures. From 97 cell lines obtained from conditioned cultures, 10 cell lines with high Taxol content were selected. Stability analyses on solid and liquid B5 media were then used to obtain lines that stably produced high levels of Taxol. Fresh biomass and Taxol production of the ninth generation became stable. Taxol content of selected CL5, CL12, and CL21 samples was 0.0448, 0.0477, and0.0428% of dry mass（DW）, respectively. Proliferation of CL5, CL12 and CL21 was 346.3, 382.5, and 409.2%,respectively. From work over about 2 years, the three cell lines appear suitable for mass production of Taxol,promoting the industrialisation and commercial-scale production of Taxol using cell culture.

A search for evidence of small-scale inhomogeneities in dense cores from line profile analysis

In order to search for intensity fluctuations on the HCN（1-0） and HCO＋（1-0） line pro- files, which could arise due to possible small-scale inhomogeneous structure, long-term observations of high-mass star-forming cores S140 and S199 were carried out. The data were processed by the Fourier filtering method. Line temperature fluctuations that exceed the noise level were detected. Assuming the cores consist of a large number of randomly moving small thermal fragments, the total number of frag- ments is - 4 × 106 for the region with linear size - 0.1 pc in S140 and - 106 for the region with linear size - 0.3 pc in S 199. Physical parameters of fragments in S 140 were obtained from detailed modeling of the HCN emission in the framework of the clumpy cloud model.

Second-line treatments for advanced gastric cancer: Interpreting outcomes by network meta-analysis

AIM: To study the effectiveness of second-linetreatments for advancer gastric cancer by application of Bayesian network meta-analysis.METHODS: Our search covered the literature up to February 2015. The following 6 treatments were evaluated:(1) irinotecan(camptothecins);(2) paclitaxel(taxanes class);(3) docetaxel(taxanes);(4) everolimus(mammalian target of rapamycin inhibitors);(5) ramucirumab(vascular endothelial growth factor receptor 2 inhibitors);(6) ramucirumab + paclitaxel. Our methodology was based on standard models of Bayesian network meta-analysis. The reference treatment was best supportive care(BSC). The endpoint was overall survival. Median survival was the outcome measure along with 95% credible intervals. RESULTS: Our search identified a total of 7 randomized controlled trials. These trials included 2298 patients(in 15 treatment arms) in whom a total of 6 active treatments were evaluated as well as BSC. There were 21 head-to-head comparisons(6 direct, 15 indirect). The difference in survival between each of two active treatments(paclitaxel and ramucirumab + paclitaxel) vs BSC was statistically significant, while the other 4 showed no statistical difference. In the 6 head-to-head comparisons between active treatments, no significant survival difference was demonstrated. CONCLUSION: Our results indicate that both paclitaxel monotherapy and ramucirumab + paclitaxel determine a significant prolongation in survival as compared with BSC.

On the Characteristics of Coaxial-Type Microwave Excited Linear Plasma:a Simple Numerical Analysis

To unveil the characteristics and available propagation mechanism of coaxial-type microwave excited line-shape plasma, the effects of parameters including microwave power, working pressure, dielectric constant, and external magnetic field on the plasma distribution were numerically investigated by solving a coupled system of Maxwell＇s equations and continuity equations. Numerical results indicate that high microwave power, relatively high working pressure, low dielectric constant, and shaped magnetic field profiles will help produce a high-density and uniform plasma source. Exciting both ends by microwave contributed to the high-density and uni- form plasma source as well. Possible mechanisms were analyzed by using the polarization model of low temperature plasma. The generation and propagation processes of the line-shape plasma mainly depend on the interaction of three aspects, i.e. the transmitted part, penetration part and absorptive part of the electromagnetic field. The numerical results were qualitatively consistent with available experimental results from literature. More elaborate descriptions of the three aspects and corresponding interactions among them need to be investigated further to improve the properties of the line-shape plasma.

Three-axis magnetic flux leakage in-line inspection simulation based on finite-element analysis

With the increase of pipelines, corrosion leakage accidents happen frequently. Therefore, nondestructive testing technology is important for ensuring the safe operation of the pipelines and energy mining. In this paper, the structure and principle of magnetic flux leakage （MFL） in-line inspection system is introduced first. Besides, a mathematic model of the system according to the ampere circuit rule, flux continuity theorem, and column coordinate transform is built, and the magnetic flux density in every point of space is calculated based on the theory of finite element analysis. Then we analyze and design the disposition of measurement section probes and sensors combining both three-axis MFL in-line inspection and multi-sensor fusion technology. Its advantage is that the three-axis changes of magnetic flux leakage field are measured by the multi-probes at the same time, so we can determine various defects accurately. Finally, the theory of finite element analysis is used to build a finite element simulation model, and the relationship between defects and MFL inspection signals is studied. Simulation and experiment results verify that the method not only enhances the detection ability to different types of defects but also improves the precision and reliability of the inspection system.

Mechanics Analysis of Overhead Transmission Lines Based On-line Monitoring

At present, the on-line monitoring is widely applied to the power line monitoring. In this paper, a new mechanical calculation model is established according to the on-line monitoring. And this model is based on the parameters that tension sensors and angle sensors on suspended points detect, and combines with the parameters of the wire itself, and also considers the deflection angel of wires due to wind. In this model, mechanics parameters of wires are turned into the new coordinate plane after deflection angel of wires due to wind, or windage yaw plane. A statics tension balance equation is built in the vertical direction of the new windage yaw plane. According to the theoretical analysis and algorithm, we verify the accuracy of this newly developed mechanical calculation model.

A quasi-isentropic model of a cylinder driven by aluminized explosives based on characteristic line analysis

A quasi-isentropic study on the process of driving a cylinder with aluminized explosives was carried out to examine the influence of the aluminum(Al) reaction rate on cylinder expansion and the physical parameters of the detonation products. Based on the proposed quasi-isentropic hypothesis and relevant isentropic theories, the characteristic lines of aluminized explosives driving a cylinder were analyzed,and a quasi-isentropic model was established. This model includes the variation of the cylinder wall velocity and the physical parameters of the detonation products with the Al reaction degree. Using previously reported experimental results, the quasi-isentropic model was verified to be applicative and accurate. This model was used to calculate the physical parameters for cylinder experiments with aluminized cyclotrimethylenetrinitramine explosives with 15.0 % and 30.0 % Al content. The results show that this quasi-isentropic model can be used not only to calculate the cylinder expansion rule or Al reaction degree, but also to calculate the physical parameters of the detonation products in the process of cylinder expansion. For explosives with 15.0 % and 30.0 % Al, 24.3 % and 18.5 % of the Al was found to have reacted at 33.9 μs and 34.0 μs, respectively. The difference in Al content results in different reaction intensity, occurrence time, and duration of two forms of reaction(diffusion and kinetic) between the Al powder and the detonation products;the post-detonation burning reaction between the Al powder and the detonation products prolongs the positive pressure action time, resulting in a continuous rise in temperature after detonation.

Analysis of the Behavior of a HV AC Line during an Atmospheric Discharge and Evaluation of the Spatio-Temporal Distribution of the Lightning Current Wave

In high voltage networks for the transport of electrical energy, lightning, a phenomenon as dangerous as it is impressive, with an easily recognizable form, can affect a power line by striking either a phase conductor, a tower or a guard cable, thus causing more dangerous and constraining stresses on the lines for its proper operation. Thus, this article aims to analyze the behavior of a HV line during an atmospheric discharge and assess the spatial and temporal distribution of the lightning current wave. For this purpose, the generalities on the transmissible power in case of link without resistance and the modeling of the atmospheric surge propagation established on the basis of the theory of the lines with distributed constants implementing the wave equation known as the Alembert equation have been developed. Through this research, we are interested in the study of the space-time distribution of the lightning current wave in order to model the radiated electromagnetic field and to examine the influence of the atmospheric discharge induced overvoltage on the transportable power of a High Voltage AC Transmission line, for a good selective protection in order to illuminate the parasites. The 2D simulation based on engineering and “Transmission Line” models have been developed as well as the verification of the coherence of the different models, by comparing the fractal dimensions of the program results with those of the experimentally obtained figures.

NEAR CRACK LINE ELASTIC-PLASTIC ANALYSIS FOR A FINITE PLATE LOADED BY TWO PAIRS OF ANTIPLANE POINT FORCES

In this paper, the improved near crack line analysis method proposed in Refs. [1] and [2] is used to investigate a center crack loaded by two pairs of antiplane point forces in a finite plate in an elastic-perfectly plastic solid. And the analytical solutions are obtained, that is elastic-plastic stress fields near the crack line and the law that the length of the plastic zone along the crack line is varied with an external loads tr,ld the bearing capacity of a finite plate with a center crack. The results of this paper are sufficiently precise near the crack line, because the assumptions of the small scale yielding theory have not been used and no other assumptions have been taken.