The Application of Digital Optical 3D Image Analyzer Evaskin in The Evaluation of Wrinkles

To verify the effectiveness of digital optical 3D image analyzer EvaSKIN in the objective and quantitative evaluation of wrinkles.A total of 115 subjects were recruited,the facial images of the subjects were collected by digital optical 3D image analyzer and manual camera,the changes of crow’s feet with age were analyzed.Pictures obtained by manual photography can be directly used for observation and preliminary grading of wrinkles.However,the requirements for evaluators are high,and the results are prone to errors,which will affect the accuracy of the evaluation.Therefore,skilled raters are needed.Compared with the manual photography method,the digital optical 3D image analyzer EvaSKIN can realize three-dimensional extraction of wrinkles,and obtain the change trend of crow’s feet with age.20~30 years old,wrinkles begin to appear slowly;wrinkles will increase rapidly at the age of 30~50;The length of 50~60 year old wrinkles is basically fixed,the wrinkles develop longitudewise,gradually widen and deepen,and the area,depth and volume increase is obvious,and the skin aging condition is intensified.the digital optical 3D image analyzer EvaSKIN realizes the 3D extraction of wrinkles,quantifies the circumference,area,average depth,maximum depth and volume of wrinkles,realizes the objective and quantitative evaluation of wrinkle state,is more accurate in the measurement of wrinkles,and provides a new instrument and method for the evaluation of wrinkles.it is a perfect and supplement to the traditional evaluation methods,and to a certain extent,it helps the research and development and evaluation institutions of cosmetics to obtain more abundant and three-dimensional data support.

Stress test and analysis based on SMS fiber structure with high sensitivity

Single mode-multimode-single mode （SMS） sensor is widely used for parameters measurement, such as bending, dis-placement, temperature, strain, refractive index, etc. Generally, SMS sensor has advantages of simple structure, low cost and easy layout, therefore it has become a research hotspot in recent years. In this paper, the multimode fiber with large core is used for manufacturing SMS structure with high sensitivity. Firstly, the multimode fiber with core/cladding diameters of 105/ 125 jitm has access to the system by means of single mode optical fiber. Secondly, SMS device structure is manufactured by welding the eccentric shaft of multimode optical fiber. Afterwards, mode interference effect and spectral response characteristics of the structure of single mode-multimode-single mode optical fiber are analyzed theoretically. Finally, with the help of a wide spectrum light source and a spectrum analyzer, the transmission spectra characteristics of SMS optical fiber with strain is tested. By observing the curve that the wave changes with stress, the sensitivity is calculated and it is consistent with theoretical value .

Case studies of high-sensitivity monitoring of natural and engineered slopes

High-sensitivity monitoring solutions are crucial for early warning systems of earth structures. In this paper, we discuss the design and implementation of such systems for natural and engineered slopes using two case studies. At the Gradenbach Observatory, one key element of the monitoring system is a large fiber optic strain rosette embedded in the slope. We demonstrate that the strain rosette can depict landslide deformations much earlier than geodetic sensors like GPS or total stations and is therefore well suitable for an early warning system. In a second application we report the construction of a reinforced earth structure using geogrids. A distributed fiber optic measurement system was installed to measure the current operating grade of the geogrids within the earth structure. About 2 km of Brillouin sensing cables were installed in the project area. It is demonstrated that the developed monitoring system is well suited for assessing the current state of health of reinforced earth structures.

Recent advances in microwave photonics

Microwave photonics （MWP） is an interdisci- plinary field that combines two different areas of microwave engineering and photonics. It has several key features by transferring signals between the optical domain and microwave domain, which leads to the advantages of broad operation bandwidth for generation, processing and distribution of microwave signals and high resolution for optical spectrum measurement. In this paper, we comprehensively review past and current status of MWP in China by introducing the representative works from most of the active MWP research groups. Future prospective is also discussed fi＇om the national strategy to key enabling technology that we have developed.

Fabrication of fiber-embedded multi-core photonic crystal fibers

A novel fabrication method of multi-core photonic crystal fibers is proposed on the basis of a fiber-embedded technique. A taper tower is used to modify the structures of the fiber preform, and four steps of fiber fabrication and different structures of fiber samples are given. The mode structures and beating characteristics of a photonic crystal fiber sample with two successive cores are investigated in detail with the help of a supercontinuum light source, a charge-coupled device （CCD） camera, and an optical spectrum analyzer. The test results show a clear beating phenomenon between two orthotropic polarization modes with a 2.8-nm peak interval in wavelength.