High Speed VCSEL-Based Parallel Optical Transmission Modules

Design and fabrication of a parallel optical transmitter are reported. The optimized 12 channel parallel optical transmitter,with each channel＇s data rate up to 3Gbit/s,is designed, assembled, and measured. A top-emitting 850nm vertical cavity surface emitting laser（VCSEL） array is adopted as the light source,and the VCSEL chip is directly wire bonded to a 12 channel driver IC. The outputs of the VCSEL array are directly butt coupled into a 12 channel fiber array. Small form factor pluggable （SFP） packaging technology is used in the module to support hot pluggable in application. The performance results of the module are demonstrated. At an operating current of 8mA, an eye diagram at 3Gbit/s is achieved with an optical output of more than 1mW.

Design and Realization of Phased Array Radar Optical Fiber Transmission System

One optical fiber transmission system is designed. The modularization optical fiber transmission adapters were utilized in the system, so the system structure could be flexibly sealable. The sub-array adapter and signal processor adapter were designed and realized utilizing the new field programmable gate array （FP- GA） which could drive the optical transceiver. The transmission agreement was designed based on the data stream. In order to solve the signal synchronization problem of the optical fiber transmitted phased array radar, a method named synchronous clock was designed. The fiber transmission error code rate of the system was zero with an experimental transmission velocity of 800 Mbit/s. The phased array radar system has detected the airplane target, thus validated the feasibility of the design method.

Research on optical properties of cardiovascular tissues based on OCT data

As a high-resolution optical imaging technology,Optical Coherence Tomography(OCT)has been widely used in the diagnosis and treatment of cardiovascular diseases.It has played an important role in the detection and identification of atherosclerotic plaques and has significant advantages.In this paper,we realized to extract the optical characteristic parameters of the target sample based on the OCT data by establishing optical transmission models conforming to the OCT principle.The optical phantoms and coronary artery of domestic pig were used as research samples to study the difference between the optical properties of the cardiovascular tissues.It can provide a basic method for further study of optical characteristic parameters of atherosclerotic plaques,and also lay a foundation for realizing the quantitative evaluation of atherosclerotic plaques with multiple optical characteristic parameters in the future.

Multi-cycle reconfigurable THz extraordinary optical transmission using chalcogenide metamaterials

Metamaterials composed of metallic antennae arrays are used as they possess extraordinary optical transmission(EOT)in the terahertz(THz)region,whereby a giant forward light propagation can be created using constructive interference of tunneling surface plasmonic waves.However,numerous applications of THz meta-devices demand an active manipula-tion of the THz beam in free space.Although some studies have been carried out to control the EOT for the THz region,few of these are based upon electrical modulation of the EOT phenomenon,and novel strategies are required for act-ively and dynamically reconfigurable EOT meta-devices.In this work,we experimentally present that the EOT resonance can be coupled to optically reconfigurable chalcogenide metamaterials which offers a reversible all-optical control of the THz light.A modulation efficiency of 88%in transmission at 0.85 THz is experimentally observed using the EOT metama-terials,which is composed of a gold(Au)circular aperture array sitting on a non-volatile chalcogenide phase change ma-terial(Ge2Sb2Te5)film.This comes up with a robust and ultrafast reconfigurable EOT over 20 times of switching,excited by a nanosecond pulsed laser.The measured data have a good agreement with finite-element-method numerical simula-tion.This work promises THz modulators with significant on/off ratios and fast speeds.

Effects of interplay between metal subwavelength slits on extraordinary optical transmission

In this paper we study the extraordinary optical transmission of one-dimensional multi-slits in an ideal metal film.The transmissivity is calculated as a function of various structural parameters.The transmissivity oscillates,with the period being just the light wavelength,as a function of the spacing between slits.As the number of slits increases,the transmissivity varies in one of three ways.It can increase,attenuate,or remain basically unchanged,depending on the spacing between slits.Each way is in an oscillatory manner.The slit interaction responsible for the oscillating transmission strength that depends on slit spacing is the subject of more detailed investigation.The interaction most intuitively manifests as a current distribution in the metal surface between slits.We find that this current is attenuated in an oscillating fashion from the slit corners to the center of the region between two adjacent slits,and we present a mathematical expression for its waveform.

Improved FEC Code Based on Concatenated Code for Optical Transmission Systems

The improved three novel schemes of the super forward error correction （super-FEC） concatenated codes are proposed after the development trend of long-haul optical transmission systems and the defects of the existing FEC codes have been analyzed. The performance simulation of the Reed-Solomon（RS）＋ Bose-Chaudhuri-Hocguenghem（BCH） inner-outer serial concatenated code is implemented and the conceptions of encoding/decoding the parallel-concatenated code are presented. Furthermore, the simulation results for the RS（255,239） ＋RS（255,239） code and the RS（255,239） ＋RS（255,223） code show that the two consecutive concatenated codes are a superior coding scheme with such advantages as the better error correction, moderate redundancy and easy realization compared to the classic RS（255,239） code and other codes, and their signal to noise ratio gains are respectively 2-3 dB more than that of the RS（255,239）code at the bit error rate of 1 × 10^-13. Finally, the frame structure of the novel consecutive concatenated code is arranged to lay a firm foundation in designing its hardware.

Giant Asymmetric Transmission and Optical Rotation of a Three-Dimensional Metamaterial

We show that giant asymmetric transmission and optical rotation for linear polarizations can be achieved by a chiral three-dimensional metamaterial composed of L-shaped and C-shaped metallic particles. Numerical calcu- lations on the electric field distributions indicate that the coupling between the electric dipolar and quadrupolar resonances in the L- and C-shaped metallic particles contributes to these effects.

Optically Driven Current Transformer with Optical Fiber Data Link

An optical fiber transmitting photoelectric coupling current transformer has been developed. In the environment of high voltage and electromagnetic fields, this device is characterized by high insulation, high reliability, small mass and high anti-interference. The structure design and operating principle of the system are introduced, measurement errors are analyzed and experimental results are given.

A planar chiral nanostructure with asymmetric transmission of linearly polarized wave and huge optical activity in near-infrared band

Just like an electronic diode that allows the electrical current to flow in one direction only, a kind of chiral metamaterial structure with a similar functionality for the electromagnetic wave is proposed. The designed nanostructure that consists of twisted metallic split-ring resonators on both sides of a dielectric substrate achieves asymmetric transmission for a forward and backward propagating linearly polarized wave by numerical simulation in near-infrared band. Difference in transmission efficiency of the optimized structure between the same polarized waves incident from opposite directions can reach a maximum at the communication wavelength （1.55 μm）. Moreover, the simulation results of this structure also exhibit strong optical activity and circular dichroism.

Effect of Overlaid Material on Optical Transmission of Side-Polished Fiber Made by Wheel Side Polishing

The performance of optical power transmission through a side-polished fiber on which materials of different refractive indices were overlaid is investigated. The experiments show that the transmitted optical power through the side-polished fiber varies with the refractive index of the overlaid material. The result of our experiments fits well the theoretical calculation. Side-polished fiber manufactured by wheel polishing method can be used not only to control optical power transmission through the fiber core but also as a refractive index sensor.

Optical transmission through basic-structural-unit superlattices

In this paper, by the transparent-component-decimation （TCD） method we obtain three kinds of new basic- components （BCs） through simplifying and decomposing the BCs of three-component Thue-Morse （3CTM） sequence. Based on these new BCs we propose a type of basic-structural-units （BSUs） and investigate the optical transmission of the one-dimensional （1D） superlattices composed of these BSUs. It is found that if the substrates of the 1D BSU superlattices are certain, the optical transmission at the central wavelength （CW） will be determined completely by the number and the type of BSUs and has nothing to do with the marshalling sequence. In particular, if the substrates are identical, the numbers of different types of BSUs are all the same and the middle two elements of BSUs constitute a cycle, then no matter whether the system is periodic, or quasiperiodic, or aperiodic, or unordered, or even random, it will be transparent at the CW. The conclusion is confirmed by the numerical results. Similar to the even layers of neighbourhood identical elements in TCD method, such a kind of optical BSU subsystem can also be decimated from the chain in the process of transmission investigation. There would be a potential application in the designing of some interesting optical devices.

Enhanced optical transmission by V-shaped nanoslit in metal film

In this paper, we reveal that the enhanced transmission through a perforated metal film can be further boosted up by a V-shaped nanoslit, which consists of two connected oblique slits. The maximum transmission at resonance can be enhanced significantly by 71.5% in comparison with the corresponding vertical slit with the same exit width. The value and position of transmission resonance peak strongly depend on the apex angle of the V-shaped slit. The optimum apex angle, at which the transmission is maximal, is sensitive to the slit width. Such phenomena can be well explained by a concrete picture in which the incident wave drives free electrons on the slit walls. Moreover, we also simply analyze the splitting of the transmission peak in the symmetry broken V-shaped slit, originating from the resonances of different parts of the V-shaped slit. We expect that our findings will be used to design the nanoscale light sources based on the metal nanoslit structures.

Study on New Concatenated Code in WDM Optical Transmission Systems

A new concatenated code of RS（255,239）＋BCH（2 040,1 930） code to he suitable for WDM optical transmission systems is proposed. The simulation resuhs show that this new concatenated code. compared with the RS（255,239）4-CSOC（k0/n0=6/7, J= 8） code in ITU-TG. 75.1, has a lower redundancy and better error-correction performance, furthermore, its net coding gain（NCG） is respectively 0. 46 dB, 0.43 dB morethanthatofRS（255,239）＋CSOC（k0/n0= 6/7, J= 8） code and BCH（3860,3824）＋BCH （2 040,1 930） code in ITU TG. 75. 1 at the third iteration for the bit error rate（BER） of 10^-12. Therefore, the new super forward error correction（Super-FEC） concatenated code can be better used in ultra long-haul, ultra large-capacity and ultra high-speed WDM optical communication systems.

Digital Signal Processing for Optical Access Networks

In this paper, we investigate advanced digital signal process ing （DSP） at the transmitter and receiver side for signal pre equalization and postequalization in order to improve spec trum efficiency （SE） and transmission distance in an optical access network. A novel DSP scheme for this optical super Nyquist filtering 9 Quadrature Amplitude Modulation （9 QAM） like signals based on muhimodulus equalization with out post filtering is proposed. This scheme recovers the Ny quist filtered Quadrature PhaseShift Keying （QPSK） signal to a 9QAMlike one. With this technique, SE can be increased to 4 b/s/Hz for QPSK signals. A novel digital superNyquist signal generation scheme is also proposed to further suppress the Nyquist signal bandwidth and reduce channel crosstalk without the need for optical prefiltering. Only optical cou plers are needed for superNyquist wavelengthdivisionmulti plexing （WDM） channel multiplexing. We extend the DSP for shorthaul optical transmission networks by using highorder QAMs. We propose a highspeed Can＇ierless Amplitude/Phase 64 QAM （CAP64 QAM） system using directly modulated la ser （DML） based on direct detection and digital equalization. Decisiondirected least mean square is used to equalize the CAP64QAM. Using this scheme, we generate and transmit up to 60 Gbit/s CAP64QAM over 20 km standard single mode fiber based on the DML and direct detection. Finally, several key problems are solved for real time orthogonalfre quencydivisionmultiplexing （OFDM） signal transmission aml processing. With coherent detection, up to 100 Glfit/s 16 QAMOFDM realtime transmission is possible.

Analysis of Optical Signal Transmission Characteristics in AWG Multi/Demultiplexer with Electromagnetic Field Theory

Based on the electromagnetic field theory, the optical signal transmission characteristics in input/output waveguides, slab waveguides and arrayed waveguides of the arrayed waveguide grating (AWG) multi/demultiplexer are analyzed. The relationship between the physical parameters such as geometry sizes and relative refractive index in AWG multi/demultiplexer and the optical signal transmission characteristics are discussed. This theoretical study can be used for optimizing the design and improving the performance of the AWG multi/demultiplexer.

New Measuring Temperature Setup with Optical Probe

Abstract: A new setup of measuring temperature is developed, which the probe is a micro- power consumptive one with CMOS circuit and is driven by optical power. For transmitting the measured signal and optical power signal in a long distance, the fiber technology is applied in this setup.

ZTE's Optical Transmission Products Used in National Backbone Network of Indonesia

1 Technical Features of ZTE’sDWDM SystemThe toll backbone wave division equipmentof ZXWM M900 backbone transmissionplatform is well designed forlarge-capacity optical transmission. It canfully satisfy the networking and managementrequirements of diversified users and be fit forvarious toll backbone networks. The systemsupports up to 40 working wavelengths and up to400 Gb/s transmission capacity, and thewavelength selection and interval are in strictcompliance with ITU-T Recommendations. It

Key Enabling Techniques and Deployment of 120Gb/s Long-Haul Optical Transmission in Backbone Networks

The explosive increase in data traffic requires networks to provide higher capacity and long-haul transmission capabilities.This paper introduces new results on high-order modulation and efficient Digital Signal Processing algorithms to reduce various transmission limitations in coherent receiving systems.Polarization Division Multiplexed Quadrature Phase Shift Keying(PDM-QPSK)is deployed to reach high bit rates,provides modified digital clock recovery,and allows BER-Aided Constant Modulus Algorithm(BA-CMA)equalising.A Soft Decision-Forward Error Correction(SD-FEC)algorithm and a joint scheme with timing recovery and adaptive equaliser are used to achieve better performance.A compact coherent transceiver is also developed.These techniques have been applied in the largest 100 G Optical Transport Network(OTN)deployment in the world,the backbone expansion project for Phase 3 of the China Education and Research Network(CERNET),with a total transmission length of 10 000 km.

Development of Modified Glasses by Transparent, Functional Hybrid Sol-Gel Nano-Ceramic Coatings, a Comparative Study

This paper concentrates on the development of glasses with self-cleaning surfaces exhibiting high water contact angles. In this study, we prepared super-hydrophobic nano-ceramic coated glass based on titania & silica using simple sol-gel & dip coating methods and studied the best composition of the coatings by altering ratios of titanium tetraisopropoxide (TTIP)/tetraethyl orthosilicate (TEOS) with different homogenizing agents. We characterized the coatings by surface roughness measurement, percentage of optical transmission, static contact angle, near-infrared (NIR) transmission, and diffuse reflectance. The fabrication of coatings on glass substrates played an important role in increasing the water contact angle of about 95° and visible & NIR transmission of about 90%. We compared our modified glass substrate with commercial low emissivity (Low E) glass using X-ray diffraction (XRD) analysis, which showed pure amorphous surface claiming excellent wettability and thus the prepared glass substrate could have a variety of applications in different fields.