Study on Direct Synthesis of Diphenyl Carbonate with Heterogeneous Catalytic Reaction (V) Screening Catalysts and Optimizing Synthesis Conditions

Pd/LaxPbyMnOz, Pd/C, Pd/molecular sieve and Pd-heteropoly acid catalysts for direct synthesis of diphenyl carbonate (DPC) by heterogeneous catalytic reaction were compared and the results of DPC synthesis indicated that the catalyst Pd/LaxPbyMnOz had higher activity. The Pd/LaxPbyMnOz catalyst and the support was characterized by XRD, SEM and TEM, the main phase was Lao.szPbo.asMnOa and the average diameter could be about 25.4nm. The optimuna conditions for synthesis of DPC with Pd/LasPbyMnOz were determined by orthogonal experiments and the experimental results showed that reaction temperature was the first factor of effect on the selectivity and yield of DPC, and the concentration of O2 in gas phase also had significant effect on selectivity of DPC. The optimum reaction conditions were catalyst/phenol mass ratio l to 50, pressure 4.5MPa, volume concentration of O2 25%, reaction temperature 60℃ and reaction time 4 h. The maximum yield and average selectivity could reach 13% and 97% respectively in the batch operation.

Direct Synthesis of Diphenyl Carbonate with Heterogeneous Catalyst and Optimal Synthesis Conditions of the Support Prepared by Sol-gel Method

The support of catalyst for the direct synthesis of diphenyl carbonate （DPC） by heterogeneous catalytic reaction was prepared by the sol-gel method. Compared with activated charcoal, molecular sieve, porous ceramics, hopcalite, the support prepared by the sol-gel method has higher activity. The characterization of the support by X-ray diffraction （XRD） and transmission electron microscope （TEM） show that the mare crystal phase is Co2MnO4 and the average particle diameter is about 40 nm. The optimum conditions for synthesis of the support were determined by orthogonal experiments, which indicate that the proportion of Cu, Mn, and Co is the first important factor influencing the yield and selectivity of DPC. Temperature of calcination is the second one. The optimum conditions are： molar proportion of Cu, Mn, and Co being 1 ： 1 ： 1, temperature of calcination 700℃, drying at 100~C, temperature of water bath 85~C. The yield and selectivity of DPC in the process can reach 38% and 99% in the batch operation, respectively. The copper cobalt manganese mixed oxides chosen as the support contribute more to the high catalytic activity than the sol-gel method.

Herbicidal activity of Aureobasidium pullulans PA-2 on weeds and optimization of its solid-state fermentation conditions

Fungal strain PA-2 was isolated from infected poplar leaves from the Ping’an District, Haidong City of Qinghai Province, China. Based on the culture characteristics and the internal transcribed spacer(ITS) sequence of its 16S r DNA, the strain was identified as Aureobasidium pullulans. The culture and metabolites of strain PA-2 showed high herbicidal potential to five tested weeds Galium aparine var. tenerum, Chenopodium album, Malva crispa, Polygonum lapathifolium and Avena fatua. For the in vitro test, 5 days after the detached leaves were inoculated with PA-2 culture, all leaves infected by the hyphae and became black and rotten. For the in vivo test, a metabolite filtrate of PA-2 culture was sprayed over the living weed plants, and five days after inoculation, the weed plants became withered and necrotic. Seven days after inoculation, the fresh weight reductions of G. aparine var. tenerum, C. album, M. crispa, P. lapathifolium and A. fatua were 87.25, 78.46, 82.25, 62.11, and 80.27%, respectively. Galium aparine var. tenerum and M. crispa exhibited significant reductions in fresh weight. The bio-safety test on the five crops showed no significant plant height reductions, which was also observed for wheat(Triticum aestivum), faba bean(Vicia faba), and barley(Hordeum vulgare). By contrast, oilseed rape(Brassica napus) and pea(Pisum sativum) exhibited light spots but no significant reductions in plant height. These results indicated that A. pullulans could be a potential microbial herbicide for the control of the target weeds in crops. Optimization of the carbon and nitrogen sources for cultural media and substances for solid-state fermentation indicated that PA-2 had better colony growth and spore production with the optimal carbon source of glucose(C4), nitrogen source of soybean flour(N2), and the optimal substance was wheat bran. The results in this study provide useful information for the development ofA. pulluans PA-2 as an herbicide for bio-control of the weed.

An Experimental Study on Optimization of Large-volume Airgun Source Excitation Conditions in a Reservoir

Through manual pickup of seismic phases,the number of recording stations,the farthest observation distance of station and received energy are determined,then optimal operating condition processing software is developed to evaluate the excitation effect of operating conditions. The optimal operating conditions in the Mianhuatan Reservoir are determined using this software. They are: optimal water depth 25 m,airgun array sink depth 9m and airgun array size 7m × 7m. At the same time,accumulative stacking results for every 10 times are analyzed for 300 fixed-point excitations. It is concluded that the excitation effect shows a rapidly rising trend at 10 to 90 times stacking,a slowly rising trend at 100 to 150 times stacking,a rapidly rising trend at 160 to 240 times stacking,and a slowly rising trend at 250 to 300 times stacking. As the number of stacking increases,the propagation distance and the number of recording stations also increase gradually.

A Good GC Stationary Phase for Separation of Xylene Isomers

An excellent separation of xylene isomers is reported using 2, 6-O-di-pentyl-3-O-acetyl-beta-CD as capillary stationary phase. The optimum conditions for the separation are also discussed.

Optimization of Extraction and Characterization of Pectin from Grapefruit Peels

In this study, pectin was extracted from grapefruit peels with hydrochloric acid and precipitated with 95% ethanol solution and 5% tartaric acid. The physical and chemical properties of pectin obtained were analyzed, including color, texture, degree of esterification, and water solubility. The effects of peel to sol- vent ratio, pH of the solvent, extraction temperature and extraction duration on pectin extraction rate were investigated. On the basis of single-factor experiments, an L9 （34） orthogonal experiment was performed to screen the optimal extraction conditions. According to the results, the optimal combination of technical parame- ters was A1B3 C1 D3, i. e. , solid to liquid ratio 1：40 （g： ml）, pH 2.0, extraction duration 70 rain, extraction temperature 90 ℃. The average pectin extraction rate was 68.60% ; the color of pectin extracted under the optimal conditions varied from milky white to light yellow; the degree of esterification of pectin extracts was 65. 71% ; the extracted pectin exhibited good water solubility. Key words Pomelo peel; Pectin extraction; Optimum conditions; Esterification degree; Water solubility

Application of Bis(2-Ethylhexyl) Sulfosuccinate(AOT) /Isooctane Reverse Micellar System in Extraction of Sesame Residue Proteins

[ Objective] To investigate the factors affecting sesame residue protein extraction and find the optimum extraction conditions, [Method ] Sesame residue proteins were extracted with bis（2-ethylhexyl）sulfosuocinate （AOT）/isooctane reverse micellar system. Orthogonal test was used to screen the optimum combination of four factors including sesame residue concentration, pre-extraction pH value, potassium chloride concentration and reverse extraction time. The yield of extracted sesame residue proteins was the indicator to evaluate the efficiency of process. E Result1 The optimum extraction conditions are as follows： sesame residue concentration： 0.06 g/ml; pre-extraction pH value, 3.0; potassium chloride concentration, 1.5 mol/L; and reverse extraction time, 20 min. In the optimum extraction conditions, the extraction rate was up to 86%. [ Coaclusion] Extraction of sesame residue proteins can be well performed with AOT/isooctane reverse micellar system.

Production and Evaluation of Synthetic Carbonated Sand as an Adsorbent Media for Batch Adsorption Process

An attempt was made to improve the adsorption capability of the normal sand to be used as adsorbent for phenol and cadmium This has been done by producing a coated sand media. The coating process was done using emulsion asphalt to convert the normal sand to carbonated sand by using chemical treatment with sulfuric acid. The production process involves mixing of the sand with asphalt and an acid, then subjecting the mix to a heating process. Different mixing ratios, heating temperatures and times （activation times） were tried to obtain the optimum conditions at which the highest removal efficiency is obtained. Three types of acids were tried acetic acid, phosphoric acid and sulfuric acid. It was found that the sulfuric acid requires the lowest activation time, hence selected for the production. The removal efficiency of the produced media was significantly affected by the temperature, mixing ratio and activation heating time. The results show that, the optimum conditions for the production process are 350 , （1：2：3） （Asphalt/acid/sand） and 52 min for temperature, mixing ratio and activation heating time respectively. The final product was tested and found effective as an adsorbent media for phenol and cadmium. The removal efficiencies of these two pollutants in a batch adsorber were found 82.42% and 86.67%, respectively. The X-R diffraction and FTIR spectra tests had proved this media as an adsorbent.

Utilization Starch of Avocado Seed （Persea Americana Mill.） as a Raw Material for Dextrin

Starch ofavocado seeds can be used as an alternative source of starch because it contains 80.1% starch. Natural starch can be made into a modified starch, for example dextrin. Dextrin can be made by using acid or enzyme hydrolysis. The purposes of this research were determine the concentration of hydrochloric acid （HCl）, the temperature and heating timein the optimum process of hydrolysis of starch into dextrin and to determine the quality of the resulting product dextrin terms of Indonesian National Standard 01-2593-1992. The methode was used in this research is hydrolisis with hydrochloric acid （HCl）. The results processing into starch avocado seed yield is 23.15%. HCl concentration, temperature and heating time significantly affect the value of dextrose equivalent （DE）, viscosity and part soluble in cold water. There is interaction between HCl concentration, temperature and heating time on the value of DE, viscosity and part soluble in cold water. Optimum conditions of process was obtained at a concentration of 0.15 N HCl, 30 minutes heating time and heating temperature of 90 ℃. Dextrose equivalent （DE） value is 19.61%. The value of solubility in cold water is 90.19%. Viscosity value is 1.61 ° E. Dextrin is not accordance with the standards of quality parameters Indonesian National Standard 01-2593-1992. Dextrin produced should be applied to non-food industry.

EXTRACTION OF ANTHRAQUINONE DERIVATIVES FROM RHUBARB RHIZOMES AND THEIR ANTIBACTERIAL TESTS

Photometry was employed to study the optimum extraction conditions of anthraquinone derivatives from rhizomes of Rheum officinale Baill in this study.The influences of extraction solvents(chloroform,benzene,ethanol,methanol,and glycerol),acid,and extraction time on the extraction yield were discussed.The results indicate that,to the Rhubarb rhizomes powder with the average particle size 0.18 mm,the conditions of the extraction solvent composed by chloroform,glycerol,and sulfuric acid(20%)in the ratio of 4:1:1(v:v),the weight of dried Rhubarb to the solvent volume in the ratio of 1:12 ew:vT,extraction time of 110 min,the anthraquinone derivatives extraction could achieve the best yield.And the antibacterial tests showed the raw extraction products had the MIC(minimal inhibitory concentration)of 20μg=mL and 30μg=mL to Staphylococcus aureus and Escherichia coli,respectively.

THE STATISTIC ANALYSIS OF SCREEN PARAMETERS ON PERFORMANCE CHARACTERISTICS

A series of laboratory screening tests have been performed with the objective of evalu-ating the effect of feed rate, screen length and screen motion on the quality of separation achieved. The statistic analysis and results derived from it are discussed. Suggestions for future work with the objective of assessing the industrial significance of the research to the optimisation and design of screening processes are presented.

Synthesis of Dimethyl-2,6-Naphthalene Dicarboxylate by Esterification Catalyzed by Sodium Tungstate

The process of synthesis of dimethyl-2,6-naphthalene dicaboxylate from esterification of 2,6-naphthalene dicarboxylic acid (2,6-NDCA) by methanol using sodium tungstate as catalyst was investigated. The orthogonal tests method was used for optimizing the process factors. The effects of reaction temperature, mass percentage of catalyst, reaction time and mass ratio of methanol to 2,6-NDCA on the 2,6-NDCA conversion were investigated. It was found that all the four factors had significant effect on the conversion. The optimum reaction conditions were reaction temperature 215 ℃,mass percentage of catalyst 3%, reaction time 3 h, mass ratio of methanol to 2,6-NDCA 6∶1. The 2,6-NDCA conversion at above condition was 92.80%.

Optima of Trypsin-Catalyzed Hydrolysis and Its Inhibition Determined by SDS-PAGE

SDS-PAGE was applied to determine trypsin activity and inhibition. After the hydrolysis by trypsin to substrate bovine serum albulnin (BSA) under different temperatures and pH, the hydrolysis degree of BSA was conducted using SDS-PAGE. From the quantitative analysis to the electrophoresis bands of BSA and its hydrolysis products in SDS-PAGE pattern, the change of trypsin activity was determined, and then the optimum temperature at 40°C and the optimum pH at pH 8.5 - 8.7 for trypsin activity were obtained. All the target bonds in BSA molecule could be hydrolyzed at the same time by trypsin. The inhibition was due to the binding of inhibitor to trypsin, which made it impossible for trypsin to touch the substrate protein. SDS-PAGE was demonstrated to be also an effect method for assaying the characteristics of trypsin activity and its inhibition.

Optimization of Ex-Situ Washing Removal of Polycyclic Aromatic Hydrocarbons from a Contaminated Soil Using Nano-Sulfonated Graphene

Ex-situ soil washing technology offers advantages such as speed and efficiency of remediation and range of application and has been developed to conform with legal requirements and best management practices in USA and some European countries. In this study, nano-sulfonated graphene （SGE） was used as a washing agent to evaluate different processing （washing） parameters for the ectopic leaching removal of polycyclic aromatic hydrocarbons （PAHs） from a coking plant soil. X-ray photoelectron spectroscopy （XPS） and fourier transform infrared spectroscopy （FTIR） were used to analyze the characteristics of the SGE tested. The results showed that SGE had a strong adsorption capacity for PAHs through the role of π-π, H-π, and anion-π interactions. The washing parameters, an SGE concentration of 2000 mg L-1, a liquid/soil （L/S） ratio of 10：1, and 4 cycles of successive washing, were set to arrive to the optimum condition for achieving more than 80% of PAH removal. Under the optimum condition, the PAH removal rate decreased with increasing ring numbers. After one washing cycle at SGE concentration of 2000 mg L-1 and L/S ratio of 10：1, the PAH removal rate of the SCE tested was much higher than that of Tween 80 （TW80） or methyl-β-cyclodextrin （MCD） （P 〈 0.01）. Therefore, SGE is a promising material for the nanoremediation of PAH-contaminated soils.

Photo-induced Synthesis and Characterization of Poly(methyl methacrylate) Grafted Sodium Salt of Partially Carboxymethylated Guar Gum

Photo-induced graft copolymerization of methyl methacrylate（MMA） onto sodium salt of partially carboxymethylated guar gum（Na-PCMGG, DS = 0.291） was carried out in an aqueous medium using ceric ammonium nitrate（CAN） as photoinitiator to synthesize a novel graft copolymer, Na-PCMGG-g-PMMA, which may find its potential application as a metal adsorbent. The influences of synthesis variables such as concentrations of photoinitiator（CAN）, nitric acid and monomer（MMA） as well as reaction time, temperature and amount of substrate on the grafting yields were studied and the reaction conditions for optimum photo-grafting were evaluated. At optimum concentration, the maximum values of the grafting yields achieved were G = 271.61% and GE = 63.89%. The experimental results were found to be in very good agreement with the proposed kinetic scheme. The photo-graft copolymerization of MMA onto Na-PCMGG（ DS = 0.291） was also carried out in the presence and absence of ultraviolet radiation for studying the efficiency of the photoinitiator. The influence of carboxymethyl groups introduced onto the guar gum molecules with regard to its behavior towards ultra-violet radiation induced grafting with MMA was also investigated. Photo-grafting process was confirmed and the products were characterized with the help of the spectroscopic（1H-NMR and FTIR） and SEM techniques.