Femtosecond laser fabrication of 3D vertically aligned micro-pore network on thick-film Li_(4)Ti_(5)O_(12)electrode for high-performance lithium storage

The development of energy storage devices with high energy density relies heavily on thick film electrodes,but it is challenging due to the limited ion transport kinetics inherent in thick electrodes.Here,we report on the preparation of a directional vertical array of micro-porous transport networks on LTO electrodes using a femtosecond laser processing strategy,enabling directional ion rapid transport and achieving good electrochemical performance in thick film electrodes.Various three-dimensional(3D)vertically aligned micro-pore networks are innovatively designed,and the structure,kinetics characteristics,and electrochemical performance of the prepared ion transport channels are analyzed and discussed by multiple characterization and testing methods.Furthermore,the rational mechanisms of electrode performance improvement are studied experimentally and simulated from two aspects of structural mechanics and transmission kinetics.The ion diffusion coefficient,rate performance at 60 C,and electrode interface area of the laser-optimized 60-15%micro-porous transport network electrodes increase by 25.2 times,2.2 times,and 2.15 times,respectively than those of untreated electrodes.Therefore,the preparation of 3D micro-porous transport networks by femtosecond laser on ultra-thick electrodes is a feasible way to develop high-energy batteries.In addition,the unique micro-porous transport network structure can be widely extended to design and explore other high-performance energy materials.

Geochemistry, Paleoenvironment and Mechanism of Organic-Matter Enrichment in the Lower Silurian Longmaxi Formation Shale in the Sichuan Basin, China

To investigate the mechanism of the organic-matter enrichment in the Lower Longmaxi Formation shale,the geochemistry and total organic carbon(TOC)of the Longmaxi Formation black shales in the Jiaoshiba,Zhaotong,and Weiyuan areas of the Sichuan Basin were analyzed.Paleoproductivity proxy parameters(Babio,Siex,and Ni/Al),clastic influx proxies(TiO2 and Ti/Al),redox indices(V/Cr,Ni/Co,V/(V+Ni),and U/Th),and hydrothermal indicators(Fe,Mn,and Y concentrations;Fe/Ti ratio and a Ni-Zn-Co diagram)were employed to decipher the paleoenvironment of the Lower Longmaxi Formation shales.TiO2 and Ti/Al indicated low terrigenous detrital influx in all three areas.However,Babio,Siex,and Ni/Al indicated high productivity in the Jiaoshiba area.V/Cr,Ni/Co,and U/Th indicated higher oxygen content with larger fluctuations in the Zhaotong and Weiyuan areas.Fe,Mn,and Y concentrations and the Fe/Ti ratio implied greater active hydrothermal activity in the Weiyuan area.These heterogeneities were considered to be closely related to the paleoenvironment and paleogeography,and the large basement faults that developed during the Chuanzhong paleo-uplift could have provided vents for deep-hydrothermal-fluid upwelling.The redox indices(V/Cr,Ni/Co,and U/Th)and a paleoproductivity proxy(Ni/Al)displayed a significant correlation with the TOC,suggesting that both excellent preservation conditions and high paleoproductivity were the controlling factors for the enrichment of organic matter in the Longmaxi Formation shale.There was no obvious correlation between the clastic influx proxy(Ti/Al)and the TOC due to the extremely low supply of terrigenous debris.The hydrothermal indicator(Fe/Ti)was negatively correlated with the TOC in the Weiyuan area,indicating that hydrothermal activity may have played a negative role in the accumulation of organic matter.This study suggests that the enrichment of organic matter in the Longmaxi Formation marine shale varied according to the paleogeography and sedimentary environment.

Model construction of micro-pores in shale: A case study of Silurian Longmaxi Formation shale in Dianqianbei area, SW China

Based on scanning electron microscopy and nitrogen adsorption experiment at low temperature, the pore types and structures of the Longmaxi Formation shale in the Dianqianbei area, SW China were analyzed, and a molecular model was built. According to mathematical statistics, the validation of the model was solved by converting it into a mathematical formula. It is found by SEM that the pores in clay mineral layers and organic pores occupy most of the pores in shale; the nitrogen adsorption experiment at low temperature reveals that groove pores formed by flaky particles and micro-pores are the main types of pores, and the results of the two are in good agreement. A molecular model was established by illite and graphene molecular structures. Moreover, based on the fractal theory and the Frenkel-Halsey-Hill formula, a modified Frenkel-Halsey-Hill formula was proposed. The reliability of the molecular model was verified to some extent by obtaining parameters such as the fractal dimension, replacement rate and fractal coefficients of correction, and mathematical calculation. This study provides the theoretical basis for quantitative study of shale reservoirs.

Effect of nitrogen on micro-pores in DD33 single crystal superalloy during solidification and homogenization

The DD33 superalloy with ultra-low nitrogen (N) content was prepared by vacuum induced melting, and the effect of N on micro-pores in the DD33 single crystal nickel-base superalloy during solidification and homogenization was investigated by in-situ X-ray computed tomography (XCT). Results indicate that the volume fraction of micro-pores, including shrinkage pores and gas pores, increases from 0.08% to 0.11% with increasing N content from 5 ppm to 45 ppm during solidification. Correspondingly, the level of micro-pores in the sample with high N content is higher than that in the sample with low N content during homogenization at 1,330 °C for different time periods. However, the evolution behaviors of gas pores is different from that of shrinkage pores during solidification and homogenization. The number of gas pores is obviously larger in the high N sample during solidification, while the number of shrinkage pores and gas pores is almost the same in both samples after 1 h homogenization. Quantitative results show that the annihilation of micro-pores is associated with bubble diffusion, while the growth behavior of micro-pores during further exposure is dominated by Kirkendall-Frenkel effect.

Finite element analysis of the effect of micro-pore defect on linear friction welding of medium carbon steel

Micro-pore is a very common material defect. In the present paper, the temperature fields of medium carbon steel joints with and without micro-pore defect during linear friction welding （LFW） were investigated by using finite element method. The effect of micro-pore defect on the axial shortening of joints during LFW was examined. The x- and y-direction displacements of micro-pore during the LFW process were also studied. In addition, the shape of micro-pore after LFW was observed. The heat conducted from the weld inteace to the specimen interior. The fluctuation range of the temperature curves for the joint with micro-pore is larger than that without micro-pore. Position of micro-pore changes with the change of the friction time. The circular shape of micro-pore becomes oval after welding.

Hydrogen etching induced hierarchical meso/micro-pore structure with increased active density to boost ORR performance of Fe-N-C catalyst

Rational regulation on pore structure and active site density plays critical roles in enhancing the performance of Fe-N-C catalysts. As the microporous structure of the carbon substrate is generally regarded as the active site hosts, its hostility to electron/mass transfer could lead to the incomplete fulfillment of the catalytic activity. Besides, the formation of inactive metallic Fe particles during the conventional catalyst synthesis could also decrease the active site density and complicate the identification of real active site. Herein, we developed a facial hydrogen etching methodology to yield single site Fe-N-C catalysts featured with micro/mesoporous hierarchical structure. The hydrogen concentration in pyrolysis process was designated to effectively regulate the pore structure and active site density of the resulted catalysts.The optimized sample achieves excellent ORR catalytic performance with an ultralow H2O2 yield(1%)and superb stability over 10,000 cycles. Our finding provides new thoughts for the rational design of hierarchically porous carbon-based materials and highly promising non-precious metal ORR catalysts.

Evaluation of pharmacokinetics and pharmacodynamics relationships for Salvianolic Acid B micro-porous osmotic pump pellets in angina pectoris rabbit

The work aims to investigate the in vitro release,pharmacokinetics(PK),pharmacodynamics(PD)and PK-PD relationships of Salvianolic Acid B micro-porous osmotic pump pellets(SalB-MPOPs)in angina pectoris New Zealand White(NZW)rabbits,compared with those of SalB immediate-release pellets(SalB-IRPs).The SalB plasma concentrations and Superoxide dismutase levels(PD index)were recorded continuously at predetermined time interval after administration,and the related parameters were calculated by using Win-Nonlin software.The release profile of MPOPs was more sustained than that of IRPs.PK results indicated that the mean C_(max) was significantly lower,the SalB plasma concentrations were steadier,both area under concentration-time curve from 0 to 24 h(AUC_(0-24 h))and from 0 to infinity(AUC_(0-∞))were presented larger,and both the peak concentration time(T_(max))and mean residence time(MRT)were prolonged for MPOPs,as compared with those of IRPs.PD results suggested that peak drug effect(E_(max))was lower and the equilibration rate constant(k_(e0))between the central compartment and the effect compartment was higher of MPOPs vs.those of IRPs.PKePD relationships demonstrated that the effectconcentration-time(ECT)course of MPOPs was clockwise hysteresis loop,and that of IRPs was counter-clockwise hysteresis loop.Collectively,those results demonstrated that MPOPs were potential formulations in treating angina pectoris induced by atherosclerosis.

Effects of Film Thickness and Anodizing Potential on the Characteristics of Micro-porous Structure on 316L Stainless Steel Surface

A novel process for fabricating an in-situ micro-porous on 316 L stainless steel was described.Aluminum films about 0.7-1.4 m in thickness were deposited on 316 L stainless steel surface by magnetron sputtering.The films were then anodized in 0.3 M oxalic acid.Through appropriate chemical dissolution,the alumina film was removed and the underlying micro-porous 316 L with diameters ranging from 500 nm to 2.4m was obtained.The morphology of the porous 316 L surface was examined by scanning electron microscope.The results indicate that the thickness of aluminum films and the anodizing potential have a combined action on the formation of porous structure on 316 L surface.Then anodic current density could be affected evidently by the film thickness.The pores size increases obviously with the increasing of the anodizing potential,when the thickness of aluminum film was about 1.4m.

Synthesis of Nano-Meter Micro-Porous Ni_xZn_((1-x))Fe_2O_4 by Hydrothermal Method

Nano-meter micro-porous Ni_xZn_((1-x))Fe_2O_4 (x=0,0.5) ferrites were obtained by hydrothermal method. Triethylamine was used as template by differential thermal analysis (DTA). The results of adsorption experiment show that the powder has micro-porous structure. The crystal structure of the powder was studied by X-ray Diffraction (XRD), and the results show that the powder is of spinel structure. The morphology of Ni_xZn_((1-x))Fe_2O_4 (x=0, 0.5) ferrite was studied by TEM, and the results show that Ni_(0.5)Zn_(0.5)Fe_2O_4 and ZnFe_2O_4 ferrite is well-crystal, well-degree of dispersion with little conglomeration because of weak magnetism. The size of the powder is below 50 nm.

Influence of Pore Forming Agent on Properties of Micro-pored CA_6-MA Material

Micro-pored CA6 -MA lightweight material with CAM： MA mass ratio of 7：3 was prepared using Al（OH） 3, MgCO3 and CaCO3 as starting materials, and anthracite. sweet potato starch and anthracite ＋ sweet potato starch as pore forming agent （PFA） with an addition of 10 mass%, 20 mass% and 30 mass%, respectively. The starting materials were dry mixed, wet co-milled in a ball mill for 1 h. slip cast into cylindrical specimens with a diameter of 60 ram. and then calcined at 1 450 ℃ for 3 h. With the increase of PFA addition,, apparent porosity increases, and bulk density decreases. The influence of different PFAs on properties of the micro-pored LW CAM -MA aggregate was investigated. The achieved CAM - MA, by adding 30% sweet potato starch, has a porosity of 76. 8%, bulk density of 0. 78 g · cm^ - 3 and median pore size of 1.90 μm.

Electrodeposition of Ir on platinum in NaCl-KCl molten salt

The reduction mechanism of Ir in the NaCl-KCl-IrCl3 molten salt was investigated by cyclic voltammetry and chronopotentiometry, and Ir film was deposited effectively on platinum in potentiostatic mode. The morphology and constitution of Ir film were examined by scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS） and X-ray diffraction （XRD）. It is found that the reduction mechanism of Ir（III） is a three-electron step and electro reaction is a reversible diffusion controlled process; the diffusion coefficients of Ir（III） at 1083, 1113, 1143 and 1183 K are 1.56×10-4, 2.23×10-4, 2.77×10-4 and 4.40×10-4 cm2/s, respectively, while the activation energy of the electrode reaction is 102.95 kJ/mol. The compacted Ir film reveals that the applied potential greatly affects the deposition of Ir, the thickness of Ir film deposited at the potential of reduction peak is the highest, the temperature of the molten salt also exerts an influence on deposition, the film formed at a lower temperature is thinner, but more micropores would occur on film when the temperature went too high.

Aggregate Stability and Its Relationship with Some Chemical Properties of Red Soils in Subtropical China

The stability of aggregates in the surface soil is crucial to soil erosion and runoff generation. Thus, to understand the stability and the breakdown mechanisms of soil aggregates as well as the relationship between aggregate stability and selected soil chemical properties, such as different forms of Fe and Al oxides, organic matter, CEC and clay content, the aggregates of slightly and severely eroded red soils derived from Quaternary red clay in subtropical China were analyzed using the routine wet sieving…

Soil Phosphorus Dynamics as Influenced by Land Use Changes in Humid Tropical, Southwest China

Land use changes can greatly influence soil phosphorus (P) dynamics, especially when converting native forests to agricultural land. Soils in Xishuangbanna, which is one of southwest China s tropical areas that maintain fragments of primary forests, were studied to a) evaluate the effect of two common land use changes, conversion of forests to agricultural land or rubber tree plantation, on the dynamics of available P and total P in bulk soils as well as total P in particle size fractions; b) assess the rel…

Micro-Mechanism of Disintegration of RE-Silicide Alloy Containing Phosphorus

The microstructure of the RE silicide alloy was studied by SEM. The feature of the phase and the distribution of Ca, P, Al were analyzed, especially the distribution of micro-cracks and its composition were determined. The result demonstrates that only a few phosphides contribute to the spontaneous crumbling of the RE silicide alloy by reacting with water and forming oxide or phosphorus oxide. The phosphorus content is not the critical factor of disintegration in the alloy studied.

Evolution of micro-pores in a single crystal nickel-based superalloy during 980℃ creep

The evolution of micro-pores in a single crystal nickel-based superalloy during creep at 980 ℃/220 MPa was investigated by X-ray computed tomography. Time-dependent ex-situ 3D information including the number, volume fraction, distribution and morphology of micro-pores was analyzed. The results reveal that the signifi cant formation and growth of micro-pores occur at the end of secondary/beginning of tertiary creep stage. The irregular large pores as well as high density pores located at strain concentration region are the major detrimental factors facilitating the creep damage. Creep failure is resulted from the connection of surface cracks induced by oxidation, and the internal cracks generated from growth and merging of micro-pores.

Controlling Effects of Tight Reservoir Micropore Structures on Seepage Ability: A Case Study of the Upper Paleozoic of the Eastern Ordos Basin, China

In this study, the types of micropores in a reservoir are analyzed using casting thin section(CTS) observation and scanning electron microscopy(SEM) experiments. The high-pressure mercury injection(HPMI) and constant-rate mercury injection(CRMI) experiments are performed to study the micropore structure of the reservoir. Nuclear magnetic resonance(NMR), gas-water relative seepage, and gas-water two-phase displacement studies are performed to examine the seepage ability and parameters of the reservoir, and further analyses are done to confirm the controlling effects of reservoir micropore structures on seepage ability. The experimental results show that Benxi, Taiyuan, Shanxi, and Shihezi formations in the study area are typical ultra-low porosity and ultra-low permeability reservoirs. Owing to compaction and later diagenetic transformation, they contain few primary pores. Secondary pores are the main pore types of reservoirs in the study area. Six main types of secondary pores are: intergranular dissolved pores, intragranular dissolved pores, lithic dissolved pores, intercrystalline dissolved pores, micropores, and microfracture. The results show that reservoirs with small pore-throat radius, medium displacement pressure, and large differences in pore-throat structures are present in the study area. The four types of micropore structures observed are: lower displacement pressure and fine pores with medium-fine throats, low displacement pressure and fine micropores with fine throats, medium displacement pressure and micropores with micro-fine throats, and high displacement pressure and micropores with micro throats. The micropore structure is complex, and the reservoir seepage ability is poor in the study areas. The movable fluid saturation, range of the gas-water two-phase seepage zone, and displacement types are the three parameters that well represent the reservoir seepage ability. According to the characteristic parameters of microscopic pore structure and seepage characteristics, the reservoirs in the study area are classified into four types(Ⅰ–Ⅳ), and types Ⅰ, Ⅱ, and Ⅲ are the main types observed. From type Ⅰ to type Ⅳ, the displacement pressure increases, and the movable fluid saturation and gas-water two-phase seepage zone decrease, and the displacement type changes from the reticulation-uniform displacement to dendritic and snake like.

Study on the electric property of shaly sand and its interpretation method

There are so many shaly sand conduction models, and most of them are only used in some local area, and have their limitations. So far, there is no theoretical model that can be used commonly and efficiently .In this paper, based on some existing models, and combining with the knowledge of the researched area, we designed out a new conduction model. The total conductivity of the rock is the combining result from free water in inter granular porous, micro pore water and the clay bound water. It can well describe many electric conduction characteristics of shaly sand. In order to make it useable in practice, we also provide some methods for interpreting the pore components with comprehensive logging data.

Preparation and Application of Light-weight Raw Materials Using Natural Forsterite

In order to develop new basic light-weight refractory raw materials,natural forsterite(<0.045 mm)and magnesite(<0.045 mm)were batched according to the chemical composition of forsterite(2MgO·SiO_(2)),wet milled,semi-dry molded and calcined at different temperatures.Then cylinder samples with diameter of 36 mm were prepared.The effects of the wet milling jar rotation speed,the calcination temperature and the anthracite addition on the properties of the samples were researched.The results show that:when the calcination temperature exceeds 1300℃,all the mineral phases have converted to the desired phases;with the increase of the rotation speed and the calcination temperature,the bulk density of the samples increases,the apparent porosity decreases and the compressive strength improves.By comprehensive consideration,400 r·min^(-1) and 1450℃ are taken as the optimal scheme.High addition of anthracite makes the samples light,so series of light-weight raw materials with uniformly distributed micro-pores can be gained.The light-weight raw materials achieved were used for insulation refractory castables,obtaining good application.

Microscopic production characteristics of crude oil in nano-pores of shale oil reservoirs during CO_(2)huff and puff

The parameters such as pore size distribution,specific surface area and pore volume of shale rock samples are analyzed by low-temperature nitrogen adsorption experiment,and then the conversion coefficient between relaxation time(T_(2))and pore size is calibrated.Nuclear magnetic resonance experiments of CO_(2)huff and puff in shale samples are carried out to study the effects of gas injection pressure,soaking time and fractures on the oil production characteristics of shale pores from the micro scale.The recovery degrees of small pores(less than or equal to 50 nm)and large pores(greater than 50 nm)are quantitatively evaluated.The experimental results show that the recovery degree of crude oil in large pores increases rapidly with the increase of injection pressure under immiscible conditions,and the effect of injection pressure rise on recovery degree of large pores decreases under miscible conditions;whether miscible or not,the recovery degree of crude oil in small pores basically maintains a linear increase with the increase of injection pressure,and the lower size limit of pores in which oil can be recovered by CO_(2)decreases with the increase of gas injection pressure;with the increase of soaking time,the recovery degree of crude oil in large pores increases slowly gradually,while the recovery degree of crude oil in small pores increases faster and then decelerates,and the best soaking time in the experiments is about 10 h;the existence of fractures can enhance the recovery degrees of crude oil in small pores and large pores noticeably.

Experimental study on hydrodynamic effect of orientation micro-pored surfaces

The orientation of the dimple increases the flow distance in the dimple and produces fluid cumulative effect in the dimple length direction, which leads to obvious hydrodynamic effect as a result. In order to investigate the hydrodynamic effect of orientation dimples, a series of experiments was carried out on a ring-on-ring test. Multi-pored faces were tested with different dimple inclination angles and slender ratios. Film thickness and frictional torque were measured under different conditions of load and rotation speed. Experimental results showed that the orientation dimple could produce obvious dynamic effect by change of the flow direction and the increasing dimple orientation leads to increase of the load capability. The hydrodynamic effect strongly depends on dimple orientation parameters such as inclination angle and slender ratio. A larger load capability can be available by increasing dimple orientation and rotation speed. Experimental results agreed well with the theory that orientation micro-pores can significantly improve hydrodynamic performance of surfaces.