The ceramic setting binders obtained by means of the raw mix mechano-chemical processing(mechanical dispersion and chemical interaction processes combination), used for bonding refractory concretes, become more availa...The ceramic setting binders obtained by means of the raw mix mechano-chemical processing(mechanical dispersion and chemical interaction processes combination), used for bonding refractory concretes, become more available with a subsequent increased interest in their properties because they develop initial strength during a heat up of the units within 8-10 h, in contrast to 24 h after placement for high Al_2O_3 cements(HAC). This strength development enables high temperature processing units to be relined with minimum turnaround time, thus providing a favored cost/performance ratio. The present paper identifies the predominant phosphate phases responsible for developing good mechanical-strength properties of zirconia and alumina concretes bonded with mechano-chemical binders. It sets out the colloid and crystalline phases resulted from interphase interaction that provide the basis for high concentrated bonding suspensions(HCBS) technology useful to the refractory industry.展开更多
The rapid development of aviation and aerospace technologies has led to increased interest in the application of numerically controlled(NC) technology for bending light-weight titanium alloy tubes.In order to study an...The rapid development of aviation and aerospace technologies has led to increased interest in the application of numerically controlled(NC) technology for bending light-weight titanium alloy tubes.In order to study and develop advanced NC bending technology,it is necessary to understand the bending performance of medium strength TA18(Ti-3Al-2.5V,ASTM Gr.9) titanium alloy tubes during NC bending under different die sets.This paper focuses on the bending performance of medium strength TA18 tubes under different NC bending die sets,including the variations in the stress,strain,wall thickness,cross sectional deformation,and defects.The results show that adding a wiper die to the base die set decreases the radial,hoop,and tangential compressive stress and the tangential compressive strain,and adding a mandrel to the base die set also decreases these stresses,but increases the radial and hoop tensile stress and decreases the hoop compressive strain obviously,and brings about a three-dimensional tensile stress concentration where the mandrel provides support.For the NC bending of medium strength TA18 tubes,the flattening of cross section is more sensitive index than the thinning of wall thickness.Introducing a mandrel can improve the flattening of cross section obviously but it has a little worse effect on the thinning of wall thickness,and adding a wiper die to the base die set can inhibit the occurrence of the inside bulge but worsen the flattening of the cross section remarkably.Considering the above effects of the mandrel and wiper die on bending performance,it is reasonable to apply the die set comprising a bending die,clamp die,and pressure die for tubes with a small diameter and the die set including an appropriate mandrel additionally for tubes with a larger diameter,in order to bend the medium strength TA18 tubes with high quality and at low cost.展开更多
Using double set parameter method, a 12-parameter trapezoidal plate bending element is presented. The first set of degrees of freedom, which make the element convergent, are the values at the four vertices and the mid...Using double set parameter method, a 12-parameter trapezoidal plate bending element is presented. The first set of degrees of freedom, which make the element convergent, are the values at the four vertices and the middle points of the four sides together with the mean values of the outer normal derivatives along four sides. The second set of degree of freedom, which make the number of unknowns in the resulting discrete system small and computation convenient are values and the first derivatives at the four vertices of the element. The convergence of the element is proved.展开更多
文摘The ceramic setting binders obtained by means of the raw mix mechano-chemical processing(mechanical dispersion and chemical interaction processes combination), used for bonding refractory concretes, become more available with a subsequent increased interest in their properties because they develop initial strength during a heat up of the units within 8-10 h, in contrast to 24 h after placement for high Al_2O_3 cements(HAC). This strength development enables high temperature processing units to be relined with minimum turnaround time, thus providing a favored cost/performance ratio. The present paper identifies the predominant phosphate phases responsible for developing good mechanical-strength properties of zirconia and alumina concretes bonded with mechano-chemical binders. It sets out the colloid and crystalline phases resulted from interphase interaction that provide the basis for high concentrated bonding suspensions(HCBS) technology useful to the refractory industry.
基金supported by the Program for New Century Excellent Talents in University of China (NCET-08-0462)the Fund of the State Key Laboratory of Solidification Processing in NWPU (Grant No. KP200919)the 111 Project of China (B08040)
文摘The rapid development of aviation and aerospace technologies has led to increased interest in the application of numerically controlled(NC) technology for bending light-weight titanium alloy tubes.In order to study and develop advanced NC bending technology,it is necessary to understand the bending performance of medium strength TA18(Ti-3Al-2.5V,ASTM Gr.9) titanium alloy tubes during NC bending under different die sets.This paper focuses on the bending performance of medium strength TA18 tubes under different NC bending die sets,including the variations in the stress,strain,wall thickness,cross sectional deformation,and defects.The results show that adding a wiper die to the base die set decreases the radial,hoop,and tangential compressive stress and the tangential compressive strain,and adding a mandrel to the base die set also decreases these stresses,but increases the radial and hoop tensile stress and decreases the hoop compressive strain obviously,and brings about a three-dimensional tensile stress concentration where the mandrel provides support.For the NC bending of medium strength TA18 tubes,the flattening of cross section is more sensitive index than the thinning of wall thickness.Introducing a mandrel can improve the flattening of cross section obviously but it has a little worse effect on the thinning of wall thickness,and adding a wiper die to the base die set can inhibit the occurrence of the inside bulge but worsen the flattening of the cross section remarkably.Considering the above effects of the mandrel and wiper die on bending performance,it is reasonable to apply the die set comprising a bending die,clamp die,and pressure die for tubes with a small diameter and the die set including an appropriate mandrel additionally for tubes with a larger diameter,in order to bend the medium strength TA18 tubes with high quality and at low cost.
基金This work is supported by NSFC(10171092)and NSF of Henan province
文摘Using double set parameter method, a 12-parameter trapezoidal plate bending element is presented. The first set of degrees of freedom, which make the element convergent, are the values at the four vertices and the middle points of the four sides together with the mean values of the outer normal derivatives along four sides. The second set of degree of freedom, which make the number of unknowns in the resulting discrete system small and computation convenient are values and the first derivatives at the four vertices of the element. The convergence of the element is proved.
基金Project (51175452) supported by the National Natural Science Foundation of ChinaProject (E2012203061) supported by the Natural Science Foundation of Hebei Province, China
