Washing-off of Unfixed Reactive Dyes on Cotton Fabrics Using Fe-TAML/H_2O_2 Catalyzed Oxidation System

Unfixed reactive dyes stained on cotton fabric could be removed using Fe-tetra-amido macro-cyclic ligands( TAML) / H_2O_2 catalyzed oxidation system( COS). The colored washing-off wastewater also could be decolorized simultaneously in the same system. The decolourization kinetics showed that the decolourization ratio of reactive dyes in water could reach at least 80% at room temperature in 10 min,which followed the law of pseudo-first order reaction kinetics. The effects of the COS washing-off process parameters on the decolourization ratio,chemical oxygen demand( COD) of wastewater,K/S value,color fastness,color difference,and bursting strength were investigated in detail. The results showed that color fastness properties and final shade of fabric treated by COS were very similar to conventional soaping. The reactive dye molecules in wash-off bath were destroyed using the COS,potentially reduced COD which generated during conventional washing-off procedure.

Energy consumption of electrooxidation systems with boron-doped diamond electrodes in the pulse current mode

A pulse current technique was conducted in a boron-doped diamond （BDD） anode system for electrochemical waste- water treatment. Due to the strong generation and weak absorption of hydroxyl radicals on the diamond surface, the BDD elec- trode possesses a powerful capability of electrochemical oxidation of organic compounds, especially in the pulse current mode. The influences of pulse current parameters such as current density, pulse duty cycle, and frequency were investigated in terms of chemical oxygen demand （COD） removal, average current efficiency, and specific energy consumption. The results demon- strated that the relatively high COD removal and low specific energy consumption were obtained simultaneously only if the current density or pulse duty cycle was adjusted to a reasonable value. Increasing the frequency slightly enhanced the COD re- moval and average current efficiency. A pulse-BDD anode system showed a stronger energy saving ability than a constant-BDD anode system when the electrochemical oxidation of phenol of the two systems was compared. The results prove that the pulse current technique is more cost-effective and more suitable for a BDD anode system for real wastewater treatment. A kinetic analysis was presented to explain the above results.

Nitrogen Removal Performance of Denitrifying Ammonium Oxidation System in Treating Sulfamethoxazole-laden Secondary Wastewater Effluent

In this study,nitrogen removal performance of the denitrifying ammonium oxidation(DAO)process was investigated when treating sulfamethoxazole(SMX)-laden secondary wastewater effluent.The influent SMX concentration showed negligible effect on efficiencies for removal of nitrate and COD.However,the ammonium ions removal rate was moderately reduced,when the influent SMX concentration in wastewater reached 6 mg/L.Total nitrogen removal efficiency remained as high as 76.77%towards the day 158 at the end of experiment.Candidatus_Brocadia and Candidatus_Kuenenia were the functional anammox strains.The unclassified_f__Rhodobacteraceae sp.was predominant heterotrophic denitrifying strain in the studied reactor.The concentrations of soluble extracellular polymeric substances in sludge obviously increased from 16.76 mg/g VSS to 32.31 mg/g VSS,which might protect the nitrogen removal strains from high-concentration SMX.This result provides a theoretical and technical foundation for the application of denitrifying ammonium oxidation process in treating sulfamethoxazole-laden secondary wastewater effluent.

Rethinking neurodegenerative diseases:neurometabolic concept linking lipid oxidation to diseases in the central nervous system

Currently,there is a lack of effective medicines capable of halting or reve rsing the progression of neurodegenerative disorde rs,including amyotrophic lateral sclerosis,Parkinson s disease,multiple sclerosis,or Alzheimer s disease.Given the unmet medical need,it is necessary to reevaluate the existing para digms of how to to rget these diseases.When considering neurodegenerative diseases from a systemic neurometabolic perspective,it becomes possible to explain the shared pathological features.This innovative approach presented in this paper draws upon exte nsive research conducted by the authors and researchers worldwide.In this review,we highlight the importance of metabolic mitochondrial dysfunction in the context of neurodegenerative diseases.We provide an overview of the risk factors associated with developing neurodegenerative disorders,including genetic,epigenetic,and environmental fa ctors.Additionally,we examine pathological mechanisms implicated in these diseases such as oxidative stress,accumulation of misfolded proteins,inflammation,demyelination,death of neurons,insulin resistance,dysbiosis,and neurotransmitter disturbances.Finally,we outline a proposal for the restoration of mitochondrial metabolism,a crucial aspect that may hold the key to facilitating curative therapeutic interventions for neurodegenerative disorders in forthcoming advancements.

Systematic engineering of BiVO_(4)photoanode for efficient photoelectrochemical water oxidation

BiVO_(4)is one of the most promising photoanode materials for photoelectrochemical(PEC)solar energy conversion,but it still suffers from poor photocurrent density due to insufficient light‐harvesting efficiency(LHE),weak photogenerated charge separation efficiency(Φ_(Sep)),and low water oxidation efficiency(Φ_(OX)).Herein,we tackle these challenges of the BiVO_(4)photoanodes using systematic engineering,including catalysis engineering,bandgap engineering,and morphology engineering.In particular,we deposit a NiCoO_(x)layer onto the BiVO_(4)photoanode as the oxygen evolution catalyst to enhance theΦ_(OX)of Fe‐g‐C_(3)N_(4)/BiVO_(4)for PEC water oxidation,and incorporate Fe‐doped graphite‐phase C_(3)N_(4)(Fe‐g‐C_(3)N_(4))into the BiVO_(4)photoanode to optimize the bandgap and surface areas to subsequently expand the light absorption range of the photoanode from 530 to 690 nm,increase the LHE andΦ_(Sep),and further improve the oxygen evolution reaction activity of the NiCoO_(x)catalytic layer.Consequently,the maximum photocurrent density of the as‐prepared NiCoO_(x)/Fe‐g‐C_(3)N_(4)/BiVO_(4)is remarkably boosted from 4.6 to 7.4 mA cm^(−2).This work suggests that the proposed systematic engineering strategy is exceptionally promising for improving LHE,Φ_(Sep),andΦ_(OX)of BiVO_(4)‐based photoanodes,which will substantially benefit the design,preparation,and large‐scale application of next‐generation high‐performance photoanodes.

Mass Transfer-Promoted Fe^(2+)/Fe^(3+)Circulation Steered by 3D Flow-Through Co-Catalyst System Toward Sustainable Advanced Oxidation Processes

Realizing fast and continuous generation of reactive oxygen species(ROSs)via iron-based advanced oxidation processes(AOPs)is significant in the environmental and biological fields.However,current AOPs assisted by co-catalysts still suffer from the poor mass/electron transfer and non-durable promotion effect,giving rise to the sluggish Fe^(2+)/Fe^(3+)cycle and low dynamic concentration of Fe^(2+)for ROS production.Herein,we present a three-dimensional(3D)macroscale co-catalyst functionalized with molybdenum disulfide(MoS_(2))to achieve ultra-efficient Fe^(2+)regeneration(equilibrium Fe^(2+)ratio of 82.4%)and remarkable stability(more than 20 cycles)via a circulating flow-through process.Unlike the conventional batch-type reactor,experiments and computational fluid dynamics simulations demonstrate that the optimal utilization of the 3D active area under the flow-through mode,initiated by the convectionenhanced mass/charge transfer for Fe^(2+)reduction and then strengthened by MoS_(2)-induced flow rotation for sufficient reactant mixing,is crucial for oxidant activation and subsequent ROS generation.Strikingly,the flow-through co-catalytic system with superwetting capabilities can even tackle the intricate oily wastewater stabilized by different surfactants without the loss of pollutant degradation efficiency.Our findings highlight an innovative co-catalyst system design to expand the applicability of AOPs based technology,especially in large-scale complex wastewater treatment.

Hypidone hydrochloride(YL-0919)ameliorates functional deficits after traumatic brain injury in mice by activating the sigma-1 receptor for antioxidation

Traumatic brain injury involves complex pathophysiological mechanisms,among which oxidative stress significantly contributes to the occurrence of secondary injury.In this study,we evaluated hypidone hydrochloride(YL-0919),a self-developed antidepressant with selective sigma-1 receptor agonist properties,and its associated mechanisms and targets in traumatic brain injury.Behavioral experiments to assess functional deficits were followed by assessment of neuronal damage through histological analyses and examination of blood-brain barrier permeability and brain edema.Next,we investigated the antioxidative effects of YL-0919 by assessing the levels of traditional markers of oxidative stress in vivo in mice and in vitro in HT22 cells.Finally,the targeted action of YL-0919 was verified by employing a sigma-1 receptor antagonist(BD-1047).Our findings demonstrated that YL-0919 markedly improved deficits in motor function and spatial cognition on day 3 post traumatic brain injury,while also decreasing neuronal mortality and reversing blood-brain barrier disruption and brain edema.Furthermore,YL-0919 effectively combated oxidative stress both in vivo and in vitro.The protective effects of YL-0919 were partially inhibited by BD-1047.These results indicated that YL-0919 relieved impairments in motor and spatial cognition by restraining oxidative stress,a neuroprotective effect that was partially reversed by the sigma-1 receptor antagonist BD-1047.YL-0919 may have potential as a new treatment for traumatic brain injury.

Deciphering Water Oxidation Catalysts:The Dominant Role of Surface Chemistry over Reconstruction Degree in Activity Promotion

Water splitting hinges crucially on the availability of electrocatalysts for the oxygen evolution reaction.The surface reconstruction has been widely observed in perovskite catalysts,and the reconstruction degree has been often correlated with the activity enhancement.Here,a systematic study on the roles of Fe substitution in activation of perovskite LaNiO_(3)is reported.The substituting Fe content influences both current change tendency and surface reconstruction degree.LaNi_(0.9)Fe_(0.1)O_(3)is found exhibiting a volcano-peak intrinsic activity in both pristine and reconstructed among all substituted perovskites in the LaNi_(1-x)Fe_(x)O_(3)(x=0.00,0.10,0.25,0.50,0.75,1.00)series.The reconstructed LaNi_(0.9)Fe_(0.1)O_(3)shows a higher intrinsic activity than most reported NiFe-based catalysts.Besides,density functional theory calculations reveal that Fe substitution can lower the O 2p level,which thus stabilize lattice oxygen in LaNi0.9Fe0.1O3 and ensure its long-term stability.Furthermore,it is vital interesting that activity of the reconstructed catalysts relied more on the surface chemistry rather than the reconstruction degree.The effect of Fe on the degree of surface reconstruction of the perovskite is decoupled from that on its activity enhancement after surface reconstruction.This finding showcases the importance to customize the surface chemistry of reconstructed catalysts for water oxidation.

Lipid droplets in the nervous system:involvement in cell metabolic homeostasis

Lipid droplets serve as primary storage organelles for neutral lipids in neurons,glial cells,and other cells in the nervous system.Lipid droplet formation begins with the synthesis of neutral lipids in the endoplasmic reticulum.Previously,lipid droplets were recognized for their role in maintaining lipid metabolism and energy homeostasis;however,recent research has shown that lipid droplets are highly adaptive organelles with diverse functions in the nervous system.In addition to their role in regulating cell metabolism,lipid droplets play a protective role in various cellular stress responses.Furthermore,lipid droplets exhibit specific functions in neurons and glial cells.Dysregulation of lipid droplet formation leads to cellular dysfunction,metabolic abnormalities,and nervous system diseases.This review aims to provide an overview of the role of lipid droplets in the nervous system,covering topics such as biogenesis,cellular specificity,and functions.Additionally,it will explore the association between lipid droplets and neurodegenerative disorders.Understanding the involvement of lipid droplets in cell metabolic homeostasis related to the nervous system is crucial to determine the underlying causes and in exploring potential therapeutic approaches for these diseases.

Nitrogen and phosphorus removal in pilot-scale anaerobic-anoxic oxidation ditch system

To achieve high efficiency of nitrogen and phosphorus removal and to investigate the rule of simultaneous nitrification and denitrification phosphorus removal （SNDPR）, a whole course of SNDPR damage and recovery was studied in a pilot-scale, anaerobicanoxic oxidation ditch （OD）, where the volumes of anaerobic zone, anoxic zone, and ditches zone of the OD system were 7, 21, and 280 L, respectively. The reactor was fed with municipal wastewater with a flow rate of 336 L/d. The concept of simultaneous nitrification and denitrification （SND） rate （rSND） was put forward to quantify SND. The results indicate that： （1） high nitrogen and phosphorus removal efficiencies were achieved during the stable SND phase, total nitrogen （TN） and total phosphate （TP） removal rates were 80% and 85%, respectively; （2） when the system was aerated excessively, the stability of SND was damaged, and rSND dropped from 80% to 20% or less; （3） the natural logarithm of the ratio of NOx to NH4^＋ in the effluent had a linear correlation to oxidation-reduction potential （ORP）; （4） when NO3^- was less than 6 mg/L, high phosphorus removal efficiency could be achieved; （5） denitrifying phosphorus removal （DNPR） could take place in the anaerobic-anoxic OD system. The major innovation was that the SND rate was devised and quantified.

Oxidation inhibition of sulfite in dual alkali flue gas desulfurization system

A laboratory-scale well-mixed thermostatic reactor with continuously blasting air was used to investigate the oxidation inhibition of sulfite in dual alkali flue gas desulfurization （FGD） system. The effects of operating parameters such as pH value and catalyst concentration on the oxidation were studied. Sodium thiosulfate was used in the system, and was found that it significantly inhabited the sulfite oxidation. In the absence of catalyst, sodium thiosulfate at 12.67 mmol/L had an inhibition efficiency of approximately 98%. While in the presence of catalyst, sodium thiosulfate at 26.72 mmol/L had an inhibition efficiency less than 85.0%. The oxidation reaction order of sulfite in the sodium thiosulfate was determined to be -1.90 and 4）.55 in the absence and presence of the catalyst, respectively. Apparent activation energy of oxidation inhibition was calculated to be 53.9 kJ/mol. Pilot tests showed that the consumption rate of thiosulfate agreed well with the laboratory-scale experimental results.

Effect of Cerium on Microstructures and High Temperature Oxidation Resistance of An Nb-Si System In-Situ Composite

Nb-16Si-24Ti-6Cr-6A1-2Hf-xCe （x =0, 0.05, 0.1,02.5, 0.5, 1 （%, atom fraction）） in situ composites were prepared by arc melting The microstmcture and the effect of rare earth element cerium on 1250℃ oxidation resistance of the composites were investigated with scanning electron microscopy （SEM） and X-ray energy disperse spectrum （EDS）, as well as X-ray diffraction （XRD）. The experimental results showed that the high temperature oxidation resistance of the alloy was improved by adding a proper amount of cerium （Ce）. The effect of Ce was considered as the concurrent of the following three factors： first, the oxide of Ce formed in the interface reduced the internal oxidation rate; second, the lath shaped oxide containing Ce increased the cracking resistance and reduced the expansion of the oxide scale; and third, the decrease of the sificide volume fraction on account of Ce addition reduces the power of the sample resisting oxygen penetration.

Oxidation of Thiophenes over Silica Gel in Hydrogen Peroxide/Formic Acid System

Thiophene (C4H4S) and 3-methylthiophene(3-MC4H4S) are typical thiophenenic sulfur compounds that exist in fluid catalytic cracking (FCC) gasoline. Oxidation of C4H4S and 3-MC4H4S were conducted in hydrogen peroxide (H2O2) and formic acid system over a series of silica gel loaded with metal oxide. The silica gel loaded with copper and cobalt (1:1) oxide was found very active for the model compound oxidation using H2O2/formic acid, while the silica gel unloaded with metal oxide was less active. The sulfur removal rate of thiophenes was different as solvent was changed. And the conversation of C4H4S and 3-MC4H4S was improved at higher temperature,but reduced when olefin was added. The sulfur removal rate of model sulfur compounds was enhanced when the phase transfer catalyst emulsifier polyethylene glycol octyl phenyl ether or tetrabutylammonium bromide(TBAB)in a H2O2 and formic acid system with the addition of TBAB, a bromine substitution trend appeared in the oxidation of thiophenes, suggesting the influence of TBAB.

Characterization of ceramic coating on ZK60 magnesium alloy prepared in a dual electrolyte system by micro-arc oxidation

Micro-arc oxidation （MAO） process was cartied out in an optimized dual electrolyte system to fabricate a compact, smooth, and corrosion resistant coating on ZK60 Mg alloy. The microstructural characteristics of coating were investigated by scanning electron microscopy （SEM） coupled with an energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. Test of mass loss was conducted at a 3.5 % NaCl solution to assess the resistance to corrosion. The bonding strength between the coating and ZK60 substrate was evaluated using scratch experiment. The results reveal that MgA1204 and MgO are the main phases of ceramic coating obtained in the dual electrolyte system. The corrosion rate of coating prepared in the optimized dual electrolyte is only 0.0061 g.m-2.h-1, which demonstrates excellent corrosion resistance. This is mainly due to the compact, uniform coating with high bonding strength.

Selective recovery of lithium from spent lithium iron phosphate batteries using oxidation pressure sulfuric acid leaching system

Oxidation pressure leaching was proposed to selectively dissolve Li from spent LiFePO_(4) batteries in a stoichiometric sulfuric acid solution.Using O_(2) as an oxidant and stoichiometric sulfuric acid as leaching agent,above 97% of Li was leached into the solution,whereas more than 99% of Fe remained in the leaching residue,enabling a relatively low cost for one-step separation of Li and Fe.And then,by adjusting the pH of leachate,above 95% of Li was recovered in the form of the Li_(3)PO_(4) product through iron removal and chemical precipitation of phosphate.

Addition of anaerobic tanks to an oxidation ditch system to enhance removal of phosphorus from wastewater

The oxidation ditch has been used for many years all over the world as an economic and efficient wastewater treatment technology. It can remove COD, nitrogen and a part of phosphorus efficiently. In the experiment described, a pilot scale Pasveer oxidation ditch system has been tested to investigate the removal of phosphorus from wastewater. The experimental results showed that influent total phosphorus(TP) was removed for 35%-50%. After this, two anaerobic tanks with total volume of 11 m 3 were added to the system to release phosphorus. As a result, the TP removal efficiency increased by about 20%. At an anaerobic HRT of about 6 hours, a TP removal efficiency of 71% was achieved.

Study on the Mechanisms for Baeyer-Villiger Oxidation of Cyclohexanone with Hydrogen Peroxide in Different Systems

The green and effective Baeyer-Villiger oxidation reaction of cyclohexanone for preparing e-caprolactone is of particular importance in the synthesis of new polymer materials. We have discussed here several mechanism types of Baeyer-Villiger oxidation of cyclohexanone with H2O2 in different reaction systems. Five main types have been addressed, i. e.： （1） the non-catalyzed reaction type, where the C=O of ketones is activated by H＋, which is electrolytically dissociated from H202 and H20, to improve the capability of C=O group for accepting the electron pairs; （2） the thermally activated radical reaction type, where the Criegee intermediate is produced via two steps of radical reaction with -OH attack, with much more hydroxyl radicals being excited in the presence of TS-1 zeolite; （3） the Bronsted acid catalysis reaction type, where both O-O moiety and C=O group could be activated by BriSnsted acid; （4） the solid Lewis acid catalyzed C=O of the substrate activation reaction type through enhancing the donor-acceptor interaction between the antibonding π＊c-o orbital of cyclohexanone and HOMO of Sn-containing zeolites; and （5） the solid Lewis acid catalyzed H202 to form Me-OOH oxidative species by converting the highest occupied molecular orbital （HOMO） of Ti-OOH into a singly occupied molecular orbital （SOMO）, making the O--O group highly electrophilic to attack the C--O of cyclohexanone during the Baeyer-Villiger oxidation process. In the end, we have also compared the different mechanisms and put forward our opinions on the development direction of catalytic materials aiming at eco-friendly Baeyer-Villiger oxidation of cyclohexanone in the years to come.

Simulation of Methane Oxidation by Paddy Soils in a Closed System

Methane oxidation by paddy soils in a closed system could be simulsted by the equation where xo and x are the CH4 concentrations at time zero and t, respectively; k1 and k2 are constants related to the constant of first-order-kinetics. According to the equation the change of soil ability to oxidize CH4 could be estimated by the equstion The results showed that the soil ability to oxidize CH4 varied, depending on the initial CH4 concentration.High initial CH4 concentration stimulated soil ability to consume CH4, while low concentration depressed the ability. This characteristic of paddy soil seemed to be of considerable significance to self-adjusting CH4 emission from flooded rice fields if there exist oxic microsites in the soil.

Oxidation and Hot Corrosion Behavior of a Composite Coating System

The oxidation and hot corrosion behavior of Co-Ni-Cr-AI-Ta-Y coating produced by magnetron sputtering with and without enamel coating has been investigated in air at 900℃ and in molten 75 wt pct NaCl+25 wt pct Na2SO4 at 850℃. The results show that the enamel coating possesses good hot corrosion resistance in the molten salts, in comparison with the sputtered Co-Ni-Cr-AI-Ta-Y coating. In the hot corrosion test, breakaway corrosion did not occur on the samples with enamel coating and the composition of enamel coating did not significantly change either. The oxidation resistance of the sputtered coating, which offers good adhesion, can be improved by the enamel coating.

Photooxidation of Methacrolein in Fe(III)-Oxalate Aqueous System and Its Atmospheric Implication

Iron and oxalic acids are widely distributed in the atmosphere and easily form ferric oxalate complex(Fe(III)-Ox).The tropospheric aqueous-phase could provide a medium to enable the photo-Fenton reaction with Fe(III)-Ox under solar irradiation.Although the photolysis mechanisms of Fe(III)-Ox have been investigated extensively,information about the oxidation of volatile organic compounds(VOC),specifically the potential for Secondary Organic Aerosol(SOA)formation in the Fe(III)-Ox system,is lacking.In this study,a ubiquitous VOC methacrolein(MACR)is chosen as a model VOC,and the oxidation of MACR with Fe(III)-Ox is investigated under typical atmospheric water conditions.The effects of oxalate concentration,Fe(III)concentration,MACR concentration,and pH on the oxidation of MACR are studied in detail.Results show that the oxidation rate of MACR greatly accelerates in the presence of oxalate when compared with only Fe(III).The oxidation rate of MACR also accelerates with increasing concentration of oxalate.The effect of Fe(III)is found to be more complicated.The oxidation rate of MACR first increases and then decreases with increasing Fe(III)concentration.The oxidation rate of MACR increases monotonically with decreasing pH in the common atmospheric water pH range or with decreasing MACR concentration.The production of ferrous and hydrogen peroxide,pH,and aqueous absorbance are monitored throughout the reaction process.The quenching experiments verify that·OH and O_(2)^(+)are both responsible for the oxidation of MACR.MACR is found to rapidly oxidize into small organic acids with higher boiling points and oligomers with higher molecular weight,which contributes to the yield of SOA.These results suggest that Fe(III)-Ox plays an important role in atmospheric oxidation.