A New Catalyst System V-Cs-Cu-Tl for Selective Oxidation of p-tert Butyl Toluene to p-tert Benzaldehyde

In this paper, a new catalysts system V-Cs-Cu-TI was studied in the gas phase selective oxidation for p-tert butyl toluene to p-tert benzaldehyde. The catalyst system was prepared by impregnation method. The results obtained are optimum value and have good advantages in environmental protection.

Corigendum to“Efficient benzaldehyde photosynthesis coupling photocatalytic hydrogen evolution”[J.Energy Chem.66(2022)52-60]

It is regretful that the wrong image of Fig.4 was used in the paperin the final proof stage by editor.The correct one should be as follow.

Novel, Green, Simple and Uncatalyzed Route for High Yield Preparation of Benzaldehyde Glycol Acetal

A simple approach for the condensation of benzaldehyde with ethylene glycol was adopted without employing any catalyst. The study reveals that factors including temperature, molar ratio of reactants, and the water removal significantly influence the conversion ratio of benzaldehyde. The results indicate that the use of optimal reaction conditions such as temperature and water removing exhibits more pronounced effects on the conversion ratio of benzaldehyde compared with the use of catalysts. In a word, a green and simple method for the condensation of aldehyde and menthandiol has been devised and investigated.

Effect of manganese and potassium addition on CeO_2-Al_2O_3 catalyst for hydrogenation of benzoic acid to benzaldehyde

A series of Mn/CeO2-Al2O3 and K/CeO2-Al2O3 catalysts for hydrogenation of benzoic acid to benzaldehyde were prepared to in- vestigate the effect of Mn, K addition on CeO2-Al2O3 catalyst. X-ray diffraction (XRD) and H2-temperature-programmed reduction (H2-TPR) results suggested that the interaction between CeO2 and MnOx enhanced the reducibility of catalysts and therefore benzoic acid conversion. The addition of K increased the number of basic number on the catalyst which leads to a high selectivity to benzaldehyde, but excessive addition imposed negative effects on the catalyst performance. A Mn-K/CeO2-Al2O3 catalyst was developed and investigated in the reaction. The simultaneous addition of Mn and K enhanced not only the catalytic activity but also the capacity to resist the coke formation over catalyst.

A Novel Bimetallic Tetrahedron Cobalt Complex Promoting the Addition of Diethylzinc to Benzaldehyde

Our recent work found a novel bimetallic tetrahedron cobalt complex which can catalyze the addition of diethylzinc to benzaldehyde effectively.

Toluene oxidization to benzaldehyde in subcritical water

Effects of reaction parameter on yield of benzaldehyde produced from toluene oxidization using hydrogen peroxide in subcritical water are investigated. The experimental results show that if the molar ratio of hydrogen peroxide to toluene is controlled within a reasonable range, the by-products may be neglected. The optimum technology of toluene oxidization to benzaldehyde is reaction time 60 min, reaction temperature 350℃, molar ratio of hydrogen peroxide to toluene 3.5. The yield of benzaldehyde can reach 17.2 % under the optimum condition. Research results of chemical reaction kinetics show that the consecutive reaction consists of two first-order reaction, and activation energy of these two reactions are 89 kJ·mol^-1 and 76 kJ·mol^-1 respectively,

Selectivity modulation in the consecutive hydrogenation of benzaldehyde via functionalization of carbon nanotubes

Hydrogenation of benzaldehyde is a typical consecutive reaction, since the intermediate benzyl alcohol is apt to be further hydrogenated. Here we demonstrate that the selectivity of benzyl alcohol can be tuned via functionalization of carbon nanotubes （CNTs）, which are used as the support of Pd. With the original CNTs, the selectivity of benzyl alcohol is 88% at a 100% conversion of benzaldehyde. With introduction of oxygen-containing groups onto CNTs, it drops to 27%. In contrast, doping CNTs with N atoms, the selectivity reaches 96% under the same reaction conditions. The kinetic study shows that hydrogenation of benzyl alcohol is significantly suppressed, which can be attributed to weakened adsorption of benzyl alcohol. This is most likely related to the modified electronic structure of Pd species via interaction with functionalized CNTs, as shown by XPS characterization.

Gas Phase Selective Catalytic Oxidation of Toluene to Benzaldehyde on V_2O_5-Ag2O/η-Al_2O_3 Catalyst

Gas phase selective catalytic oxidation of toluene to benzatdehyde was studied on V_2O_5-Ag_2O/η-Al_2O_3 catalyst prepared by impregnation. The catalyst was characterized by XRD, XPS, TEM, and FT-IR. The catalytic results showed that toluene conversion and selectivity for benzaldehyde on catalyst sample No.4 (V/(V+Ag)=0.68) was higher than other catalysts with different V/Ag ratios. This was attributed to the higher surface area, larger pore volume and pore diameter of the catalyst sample No. 4 than the other catalysts. The XRD patterns recorded from the catalyst before and after the oxidation reaction revealed that the new phases were developed, and this suggested that silver had entered the vanadium lattice. XPS results showed that the vanadium on the surface of No.4 and No.5 sample was more than that in the bulk, thus forming a vanadium rich layer on the surface. It was noted that when the catalyst was doped by potassium promoter, the toluene conversion and selectivity for benzaldehyde were higher than those on the undoped catalyst. This was attributed to the disordered structure of V_2O_5 lattice of the K-doped catalyst and a better interracial contact between the particles.

Effect of benzaldehyde on the electrodeposition and corrosion properties of Ni–W alloys

The effect of different concentrations of benzaldehyde on the electrodeposition of Ni–W alloy coatings on a mild steel substrate from a citrate electrolyte was investigated in this study. The electrolytic alkaline bath(p H 8.0) contained stoichiometric amounts of nickel sulfate, sodium tungstate, and trisodium citrate as precursors. The corrosion resistance of the Ni–W-alloy-coated specimens in 0.2 mol/L H2SO4 was studied using various electrochemical techniques. Tafel polarization studies reveal that the alloy coatings obtained from the bath containing 50 ppm benzaldehyde exhibit a protection efficiency of 95.33%. The corrosion rate also decreases by 21.5 times compared with that of the blank. A higher charge-transfer resistance of 1159.40 ?·cm2 and a lower double-layer capacitance of 29.4 μF·cm-2 further confirm the better corrosion resistance of the alloy coating. X-ray diffraction studies reveal that the deposits on the mild steel surface are consisted of nanocrystals. A lower surface roughness value(Rmax) of the deposits is confirmed by atomic force microscopy.

Kinetics and Mechanism Modeling of Liquid-Phase Toluene Oxidation to Benzaldehyde Catalyzed by Mn–Mo Oxide

In this study, liquid-phase aerobic oxidation of toluene catalyzed by Mn–Mo oxide was conducted in a 1.0 L batch reactor. The macroscopic kinetics of toluene consumption and benzaldehyde generation at 413–443 K were obtained from a combination of experimental observation and hypothetical models. The results clearly showed that both the oxidation rate of toluene and generation rate of the aromatic product were proportional to the concentration of the substrate, the partial pressure of oxygen and the surface area of the catalyst. The energy barrier of toluene oxidation to benzyl alcohol was the highest(≈ 81 kJ mol^(-1)), while that of benzyl alcohol oxidation to benzaldehyde was the lowest(≈ 57 kJ mol^(-1)). Moreover, the activation energy of further oxidation of benzaldehyde in an acetic acid solvent was only slightly lower(≈ 1.9 kJ mol^(-1)) than that of toluene oxidation. Significantly, the transformation of benzyl alcohol indeed contributed to the generation of benzaldehyde and this step conformed to a first-order parallel-consecutive model. Increased reaction temperature and residence time favored the transformation of benzyl alcohol to benzaldehyde. In addition, doping with molybdenum at Mn/Mo = 3/1 enhanced the catalytic performance of the heterogeneous catalyst and was attributed to the presence of a synergetic effect between different metal cations. Regarding the microscopic kinetics, the LH-OS-ND mechanism(Langmuir–Hinshelwood adsorption of reagents on the same type of active sites and non-dissociative adsorption of oxygen) was verified as responsible for the heterogeneous oxidation of toluene. Oxygen and benzaldehyde were weakly adsorbed(Δ H_(ads,Oxy) ≈^(-1)5 kJ mol^(-1), Δ H _(ads)0,Bald) ≈-30 kJ mol^(-1)), but showed strong mobility(Δ S_(ads,Oxy) ≈-22 J mol^(-1) K^(-1)), Δ S_(ads,Bald) ≈-39 J mol^(-1) K^(-1)). The fundamental intrinsic rates were deduced based on the LH-OS-ND mechanism and showed great consistency with the macroscopic results.

β-Cyclodextrin Promoted Oxidation of Cinnamaldehyde to Natural Benzaldehyde in Water

一个灵巧、有效的过程被钠次氯酸盐为 cinnamaldehyde 的氧化劈开系统地开发了到 benzaldehyde 与是的水唯一的溶剂面对 -cyclodextrin (作为 -CD) 缩短了。例如反应温度的不同因素影响 cinnamaldehyde 氧化，催化剂和氧化剂的数量，被调查了。benzaldehyde 的收益在最佳条件下面到达 76%(333 K， 4 h，到 CD 的 cinnamaldehyde 的臼齿的比率是 1:1 ) 。而且，包括 benzaldehyde 和二个主要副产品(cinnamaldehyde 的 phenylacetaldehyde 和 epoxide ) 的形成的可行反应机制被建议了。

STUDY ON THE TREATMENT OF 3—PHENOXY—BENZALDEHYDE INDUSTRIAL WASTEWATER WITH POLYMERIC ADSORBENT

In this paper,the two effluents from PBA (3-phenoxy-benzaldehyde) production process were treated by polymeric adsorbent CHA-111.PBA or PBC (3-phenoxy-benzoic acid) was recovered from the wastewater in the process of neutralization.As a secondary treatment method,adsorption with CHA-111 showed better efficiency than photocatolytic decomposition and solvent extraction.The optimal technological parameters were:adsorption:current velocity:2.0BV/hr(bed volume per hour),room temperature;desorption:current velocity:2.0BV/hr(bed volume per hour),room temperature;desorption:current velocity:1.0 BV/hr,80℃,8% sodium hydroxide aqueous solutions.In conclusion,99.9% COD in the neutralizing wastewater and 98.4% COD in the hydrolysis wastewater are removed successfully.

Cobalt(I) Catalyzed Reaction of Benzaldehydes with Functionalized Benzylic Zinc Halides

Functionalized benzylic zinc halides reacted with benzaldehydes in the presence of Lewis acid Me3SiCl giving high yields of trans-stilbenes under the catalysis of Co(PPh3)3Cl.

Study on the Recycling of Mediator in Indirect Electrosynthesis of Benzaldehyde

This paper has studied the recycling of the oxidation mediator Mn(Ⅲ)/Mn(Ⅱ) and sulfuric acid solution in process of indirect electrosynthesis of benzaldehyde. Experimental resalts show that mis recycling may be realized When electrolysis and synthetic reaction are carried out in the same concentration of 60% H2SO4 separately, then there will be no waste discharged, energy consumption will be decreased and almost no current efficiency will be lossed during recycling process. The optimun current efficiency is 76%, yield of benzaldehyde is 64%.

Catalytic Reduction of Benzaldehyde Under Hydrogen Flow over Nickel-Containing Mesoporous Silica Catalysts

The hydrogenation of benzaldehyde over a series of nickel-containing mesoporous silicas with different nickel contents was studied at atmospheric pressure in the range temperature of 393 - 513 K under H2 ?ow. These materials (noted Nin-HMS with n = Si/Ni = 50, 25, 15) have been prepared at room temperature using a route based on hydrogen bonding and self-assembly between neutral primary amine micelles (S0) and neutral inorganic precursors (I0). They were characterized by their chemical analysis, BET surface area, XRD, FT-IR, and SEM microscopy. The obtained products were benzylalcohol, toluene, benzene with yields depending on the nickel content (Si/Ni ratio) and reaction temperature. The products of benzaldehyde hydrogenation (benzylalcohol, and toluene) and hydrogenolysis (benzene) were preferentially formed at low/middle and high reaction temperature respectively. The mesoporous Ni-containing materials were very active hydrogenation catalysts with almost 90% selectivity to benzylalcohol product and showed excellent stability. A mechanism in which the reaction could be initiated by a benzaldehyde reduction over Nin-HMS materials under hydrogen flow with formation of reaction products is proposed.

Dielectric Behaviour of Mixtures of Polyethylene Glycol with Propionaldehyde and Benzaldehyde

The dielectric constant e' and dielectric loss e' of several mixtures of propionaldehyde-polyethylene glycol (system 1) and benzaldehyde-polyethylene glycol (system II) have been measured within the frequency band 105-107 Hz and the temperature range 20-50℃. The dielectric behaviour is discussed. on the other hand, the dielectric relaxation time T. activation energy △He, and entorpy change △Se for the dielectric relaxation as well as activation energy of viscous flow △Hv are calculated for the same temperature range. It is suggested that the observed increase in T values with increas.ng glycol content is due to an increase in the hydrogen bonding in the aggregates or clusters which would be formed between the carbonyl group of the aldehyde and the hydrogen atoms from the glycot molecules. In addition， the higher values of T, △He, and △Se in case of system (II) than that in case of system (I) may be due to the greater volume of the aggregates and the stronger dipole-dipole forces in system (II) compared with those in system (I).

Quantum chemical study on asymmetric allylation of benzaldehyde in the presence of chiral allylboronate

The quantum chemical method is employed to study the modified asymmetric allylation of benzaldehyde controlled by diisopropyl D-(-)-tartrate auxiliary. All the structures are optimized completely at the B3LYP/6-31G(d,p) level. The (R)-secondary alcohol can be achieved mainly through a six-membered ring chair-like transition state structure. From the relative reaction rates theory the main product configuration predicted is in agreement with the experiment result.

GRAFTED STYRENE-DIVINYLBENZENE COPOLYMERS CONTAINING BENZALDEHYDES AND THEIR WITTIG REACTIONS WITH VARIOUS PHOSPHONIUM SALTS

A chloromethylated styrene-divinylbenzene copolymer support system functionalized with 4-benzaldehyde and 2-benzaldehyde was prepared. The degree of functionalization with aldehyde groups is well suited for the subsequent use of the products as Wittig reagents. The polymer bound aldehyde was reacted with Wittig reagents to give olefin groups grafted on styrene-divinylbenzene copolymers. The reactions were carded out in phase transfer catalysis conditions. A simple procedure for the calculation of the degree of functionalization and the statistical modeling of the structural repetitive unit of the copolymer are reported.

Wavelength-dependent Photodissociation Dynamics of Benzaldehyde

在 260， 271， 284，和 287 nm 刺激之上的 benzaldehyde 的 ultrafast 动力学被 femtosecond 泵探查 time-of-flight 团 spectrometry 学习了。一个双性人指数的腐烂部件模型被使用适合 benzaldehyde 离子和碎片离子的短暂侧面。在 S2 起源，部件的第一腐烂被归因于内部变换到 S1 状态的高震动的层次。第一个部件的一生与增加震动的精力减少了，由于震动的层次的高密度的影响。第二腐烂被分到其一生是大约 600 fs 的 S1 的震动的松驰。在 287 nm 刺激之上，第一腐烂变得超短波(~ 56 fs ) 它从 S1 为 intersystem 十字被带去 T2，当第二个腐烂部件被归因于震动的松驰时。碎片短暂的泵探查也在 284 nm 泵与不同探查紧张被学习。