Understanding the relationship between the chemical composition and pyrolysis performance of endothermic hydrocarbon fuel(EHF) is of great significance for the design and optimization of advanced EHFs. In this work, t...Understanding the relationship between the chemical composition and pyrolysis performance of endothermic hydrocarbon fuel(EHF) is of great significance for the design and optimization of advanced EHFs. In this work, the effect of deep hydrogenation on the pyrolysis of commercial RP-3 is investigated.Fuels with different hydrogenation degrees were obtained by the partially and completely catalytic hydrogenation and their pyrolysis performances were investigated using an apparatus equipped with an electrically heated tubular reactor. The results show that with the increase of hydrogenation degree, fuel conversion almost remains constant during the pyrolysis process(500-650°C, 4 MPa);however, the heat sink increases slightly, and the anti-coking performance significantly improves, which are highly related to their H/C ratios. Detailed characterisations reveal that the difference of the pyrolysis performance can be ascribed to the content of aromatics and cycloalkanes: the former are prone to initiate secondary reactions to form coking precursors, while the latter could act as the hydrogen donor and release hydrogen, which will terminate the radical propagation reactions and suppress the coke deposition. This work should provide the guidance for upgrading EHFs by modulating the composition of EHFs.展开更多
Magnesium hydride is one of the most promising solid-state hydrogen storage materials for on-board application.Hydrogen desorption from MgH_(2) is accompanied by the formation of the Mg/MgH_(2) interfaces,which may pl...Magnesium hydride is one of the most promising solid-state hydrogen storage materials for on-board application.Hydrogen desorption from MgH_(2) is accompanied by the formation of the Mg/MgH_(2) interfaces,which may play a key role in the further dehydrogenation process.In this work,first-principles calculations have been used to understand the dehydrogenation properties of the Mg(0001)/MgH_(2)(110) interface.It is found that the Mg(0001)/MgH_(2)(110) interface can weaken the Mg-H bond.The removal energies for hydrogen atoms in the interface zone are significantly lower compared to those of bulk MgH_(2).In terms of H mobility,hydrogen diffusion within the interface as well as into the Mg matrix is considered.The calculated energy barriers reveal that the migration of hydrogen atoms in the interface zone is easier than that in the bulk MgH_(2).Based on the hydrogen removal energies and diffusion barriers,we conclude that the formation of the Mg(0001)/MgH_(2)(110) interface facilitates the dehydrogenation process of magnesium hydride.展开更多
Industrial catalyst waste has emerged as a hazardous pollutant that requires safe and proper disposal after the unloading process.Finding a valuable and sustainable strategy for its treatment is a significant challeng...Industrial catalyst waste has emerged as a hazardous pollutant that requires safe and proper disposal after the unloading process.Finding a valuable and sustainable strategy for its treatment is a significant challenge compared to traditional methods.In this study,we present a facile method for the recovery of molybdenum and aluminum contents from spent Mo-Ni/Al_(2)O_(3) hydrogenation catalysts through crystallization separation and coprecipitation.Furthermore,the recovered molybdenum and aluminum are utilized as active metals and carriers for the preparation of new catalysts.Their properties were thoroughly analyzed and investigated using various characterization techniques.The hydrogenation activity of these newly prepared catalysts was evaluated on a fixed-bed small-scale device and compared with a reference catalyst synthesized from commercial raw reagents.Finally,the hydrogenation activity of the catalysts was further assessed by using the entire distillate oil of coal liquefaction as the raw oil,specifically focusing on denitrogenation and aromatic saturation.This work not only offers an effective solution for recycling catalysts but also promotes sustainable development.展开更多
Optimizing the intrinsic activity of non-noble metal by precisely tailoring electronic structure offers an appealing way to construct cost-effective catalysts for selective biomass valorization.Herein,we reported a P-...Optimizing the intrinsic activity of non-noble metal by precisely tailoring electronic structure offers an appealing way to construct cost-effective catalysts for selective biomass valorization.Herein,we reported a P-doping bifunctional catalyst(Ni-P/mSiO_(2))that achieved 96.6%yield for the hydrogenation rearrangement of furfural to cyclopentanone at mild conditions(1 MPaH_(2),150°C).The turnover frequency of Ni-P/mSiO_(2)was 411.9 h^(-1),which was 3.2-fold than that of Ni/mSiO_(2)(127.2 h^(-1)).Detailed characterizations and differential charge density calculations revealed that the electron-deficient Niδ+species were generated by the electron transfer from Ni to P,which promoted the ring rearrangement reaction.Density functional theory calculations illustrated that the presence of P atoms endowed furfural tilted adsorb on the Ni surface by the C=O group and facilitated the desorption of cyclopentanone.This work unraveled the connection between the localized electronic structures and the catalytic properties,so as to provide a promising reference for designing advanced catalysts for biomass valorization.展开更多
For the first time,the MgH_(2)–NaAlH_(4)(ratio 4:1)destabilized system with CoTiO_(3) addition has been explored.The CoTiO_(3)-doped MgH_(2)–NaAlH_(4) sample begins to dehydrogenate at 130℃,which is declined by 40...For the first time,the MgH_(2)–NaAlH_(4)(ratio 4:1)destabilized system with CoTiO_(3) addition has been explored.The CoTiO_(3)-doped MgH_(2)–NaAlH_(4) sample begins to dehydrogenate at 130℃,which is declined by 40℃ compared to the undoped MgH_(2)–NaAlH_(4).Moreover,the de/rehydrogenation kinetics characteristics of the CoTiO_(3)-doped MgH_(2)–NaAlH_(4) were greatly ameliorated.With the inclusion of CoTiO_(3),the MgH_(2)–NaAlH_(4) composite absorbed 5.2 wt.%H_(2),higher than undoped MgH_(2)–NaAlH_(4).In the context of dehydrogenation,the CoTiO_(3)-doped MgH_(2)–NaAlH_(4) sample desorbed 2.6 wt.%H_(2),almost doubled compared to the amount of hydrogen desorbed from the undoped MgH_(2)–NaAlH_(4) sample.The activation energy obtained by the Kissinger analysis for MgH_(2) decomposition was significantly lower by 35.9 kJ/mol than the undoped MgH_(2)–NaAlH_(4) sample.The reaction mechanism demonstrated that new phases of MgCo and AlTi_(3) were generated in situ during the heating process and are likely to play a substantial catalytic function and be useful in ameliorating the de/rehydrogenation properties of the destabilized MgH_(2)–NaAlH_(4) system with the inclusion of CoTiO_(3).展开更多
A series of model catalysts were obtained by treating commercial fresh and spent catalysts unloaded from the factory with different methods, including green oil dipping, extraction and high-temperature regeneration;fi...A series of model catalysts were obtained by treating commercial fresh and spent catalysts unloaded from the factory with different methods, including green oil dipping, extraction and high-temperature regeneration;finally, the deactivation behavior of the commercial catalyst for acetylene hydrogenation were studied. The influence of various possible deactivation factors on the catalytic performance was elucidated via detailed structural characterization, surface composition analysis, and activity evaluation.The results showed that green oil, carbon deposit and sintering of active metal were the main reasons for deactivation, among which green oil and carbon deposit led to rapid deactivation, while the activity could be recovered after regeneration by high-temperature calcination. The sintering of active metal components was attributed to the high-temperature regeneration in hydrothermal conditions, which was slow but irreversible and accounted for permanent deactivation. Thus, optimizing the regeneration is expected to extend the service life of the commercial catalyst.展开更多
Catalysts with varying Fe contents were prepared using a sequential impregnation method to investigate the effects of Fe addition on the physicochemical properties of Pt/Al_(2)O_(3) and their performance in methylcycl...Catalysts with varying Fe contents were prepared using a sequential impregnation method to investigate the effects of Fe addition on the physicochemical properties of Pt/Al_(2)O_(3) and their performance in methylcyclohexane(MCH)dehydrogenation.The results demonstrated that the addition of Fe to Pt/Al_(2)O_(3) enhanced the electron density of Pt and improved catalytic activity,while exhibiting negligible influence on the catalytic selectivity for toluene.When the Fe content was 0.057%,the catalyst exhibited the highest MCH consumption rate,which was approximately two times higher than that of the catalyst without Fe.Additionally,the incorporation of Fe inhibited the formation of coke and reduced the quantity of coke deposits on the catalyst,thereby improving its catalytic durability.Overall,Fe shows promise as a prospective secondary element for Pt/Al_(2)O_(3) to enhance the MCH dehydrogenation performance.展开更多
Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is report...Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is reported to fabricate Pd nanoparticle catalyst over γ-Al_(2)O_(3)or Fe_(2)O_(3)/γ-Al_(2)O_(3)support,using palladium hexafluoroacetylacetonate as the Pd precursor and H_(2)plasma as counter-reactant.Scanning transmission electron microscopy exhibits that highdensity Pd nanoparticles are uniformly dispersed over Fe_(2)O_(3)/γ-Al_(2)O_(3)support with an average diameter of 4.4 nm.The deposited Pd-Fe_(2)O_(3)/γ-Al_(2)O_(3)shows excellent catalytic performance for CO_(2)hydrogenation in a dielectric barrier discharge reactor.Under a typical condition of H_(2)to CO_(2)ratio of 4 in the feed gas,the discharge power of 19.6 W,and gas hourly space velocity of10000 h^(-1),the conversion of CO_(2)is as high as 16.3% with CH_(3)OH and CH4selectivities of 26.5%and 3.9%,respectively.展开更多
The metal promoted In_(2)O_(3) catalysts for CO_(2) hydrogenation to methanol have attracted wide attention because of their high activity with high methanol selectivity.However,there was still no experimental confirm...The metal promoted In_(2)O_(3) catalysts for CO_(2) hydrogenation to methanol have attracted wide attention because of their high activity with high methanol selectivity.However,there was still no experimental confirmation if copper could be a good promoter for In_(2)O_(3).Herein,the Cu promoted In_(2)O_(3) catalyst was prepared using a deposition-precipitation method.Such prepared Cu/In_(2)O_(3) catalyst shows significantly higher CO_(2) conversion and space time yield(STY)of methanol,compared to the un-promoted In_(2)O_(3) catalyst.The loading of Cu facilitates the activation of both H_(2) and CO_(2) with the interface between the Cu cluster and defective In_(2)O_(3) as the active site.The Cu/In_(2)O_(3) catalyst takes the CO hydrogenation pathway for methanol synthesis from CO_(2) hydrogenation.It exhibits a unique size effect on the CO adsorption.At temperatures below 250℃,CO adsorption on Cu/In_(2)O_(3) is stronger than that on In_(2)O_(3),causing higher methanol selectivity.With increasing temperatu res,the Cu catalyst aggregates,which leads to the formation of weak CO adsorption site and causes a decrease in the methanol selectivity.Compared with other metal promoted In_(2)O_(3) catalysts,it can be concluded that the catalyst with stronger CO adsorption possesses higher methanol selectivity.展开更多
Cu/ZnO is widely used in the hydrogenation of carbon dioxide (CO_(2)) to methanol (CH_(3)OH) to improve the lowconversion rate and selectivity generally observed. In this work, a series of In, Zr, Co, and Ni-doped CuO...Cu/ZnO is widely used in the hydrogenation of carbon dioxide (CO_(2)) to methanol (CH_(3)OH) to improve the lowconversion rate and selectivity generally observed. In this work, a series of In, Zr, Co, and Ni-doped CuO-ZnO catalysts wassynthesized via a hydrothermal method. By introducing a second metal element, the activity and dispersion of the activesites can be adjusted and the synergy between the metal and the carrier can be enhanced, forming an abundance of oxygenvacancies. Oxygen vacancies not only adsorb CO_(2) but also activate the intermediates in methanol synthesis, playing a keyrole in the entire reaction. Co3O4-CuO-ZnO had the best catalytic performance (a CO_(2) conversion rate of 9.17%;a CH_(3)OHselectivity of 92.77%). This study describes a typical strategy for multi-component doping to construct a catalyst with anabundance of oxygen vacancies, allowing more effective catalysis to synthesize CH_(3)OH from CO_(2).展开更多
Alumina(Al_(2)O_(3))is widely used in the chemical industry as the catalyst and support due to its high specific surface area,abundant pore size distribution and chemical stability.However,the occurrence of hydration ...Alumina(Al_(2)O_(3))is widely used in the chemical industry as the catalyst and support due to its high specific surface area,abundant pore size distribution and chemical stability.However,the occurrence of hydration in water environment,result in outstanding decrease in specific surface area and collapse of pore structure.In this work,dodecyl phosphoric acid(PA)is used to modify the surface of Al_(2)O_(3)to obtain a series of hydrophobic material(Al_(2)O_(3)-PA).Based on XPS and NMR analysis,PA is chemically bonded on Al_(2)O_(3)to form PAOAAl bond.Furthermore,BET and WCA results display that Al_(2)O_(3)-1PA exhibits excellent the hydrophobicity and hydrothermal stability while maintains the pore structure.Take it as the substrate to support the Pd nanoparticles,the as-prepared Pd/Al_(2)O_(3)-PA shows the superior catalytic performance in the hydrogenation of phenol and anthraquinone relative to Pd/Al_(2)O_(3),indicating the accessibility of Pd sites after PA modification.Especially,the significantly enhanced stability is also obtained in four cycles for aqueous phenol hydrogenation.This can be ascribed that the PA modification inhibits the aggregation of Pd nanoparticles and the products adhesion in the reaction process.The extension of PA coatings to monolithic catalysts could expand their current capabilities in industrial applications and warrants ongoing investigation.展开更多
The interaction between a promoter and an active metal crucially impacts catalytic performance.Nowadays,the influence of promoter contents and species has been intensively considered.In this study,we investigate the e...The interaction between a promoter and an active metal crucially impacts catalytic performance.Nowadays,the influence of promoter contents and species has been intensively considered.In this study,we investigate the effect of the iron(Fe)-zinc(Zn)proximity of Fe-Zn bimetallic catalysts on CO_(2)hydrogenation performance.To eliminate the size effect,Fe_(2)O_(3)and ZnO nanoparticles with uniform size are first prepared by the thermal decomposition method.By changing the loading sequence or mixing method,a series of Fe-Zn bimetallic catalysts with different Fe-Zn distances are obtained.Combined with a series of characterization techniques and catalytic performances,Fe-Zn bimetallic proximity for compositions of Fe species is discussed.Furthermore,we observe that a smaller Fe-Zn distance inhibits the reduction and carburization of the Fe species and facilitates the oxidation of carbides.Appropriate proximity of Fe and Zn(i.e.,Fe_1Zn_(1)-imp and Fe_(1)Zn_(1)-mix samples)results in a suitable ratio of the Fe_5C_(2)and Fe_(3)O_(4)phases,simultaneously promoting the reverse water-gas shift and Fischer-Tropsch synthesis reactions.This study provides insight into the proximity effect of bimetallic catalysts on CO_(2)hydrogenation performance.展开更多
CO_(2)hydrogenation has been considered to be a highly promising route for the production of high-value olefins(HVOs)while also mitigating CO_(2)emissions.However,it is challenging to achieve high selectivity and main...CO_(2)hydrogenation has been considered to be a highly promising route for the production of high-value olefins(HVOs)while also mitigating CO_(2)emissions.However,it is challenging to achieve high selectivity and maintain stable performance for HVOs(ethylene,propylene,and linear a-olefins)over a prolonged reaction time due to the difficulty in precise control of carbon coupling and rapid catalyst deactivation.Herein,we present a selective Ba and Na co-modified Fe catalyst enriched with Fe_(5)C_(2)and Fe_(3)C active sites that can boost HVO synthesis with up to 66.1%selectivity at an average CO_(2)conversion of 38%for over 500 h.Compared to traditional NaFe catalyst,the combined effect of Ba and Na additives in the NaBaFe-0.5 catalyst suppressed excess oxidation of FeCxsites by H_(2)O.The absence of Fe3O4phase in the spent NaBaFe-0.5 catalyst reflects the stabilization effect of the co-modifiers on the FeCxsites.This study provides a strategy to design Fe-based catalysts that can be scaled up for the stable synthesis of HVOs from CO_(2)hydrogenation.展开更多
Cu-based catalysts are widely employed for CO_(2) hydrogenation to methanol,which is expected as a promising process to achieving carbon neutrality.However,most Cu-based catalysts still suffer from low methanol yield ...Cu-based catalysts are widely employed for CO_(2) hydrogenation to methanol,which is expected as a promising process to achieving carbon neutrality.However,most Cu-based catalysts still suffer from low methanol yield with a passable CO_(2) conversion and lack insight into its reaction mechanism for guiding the design of catalysts.In this work,Cu^(+)/CeZrO_(x) interfaces are engineered by employing a series of ceria-zirconia solid solution catalysts with various Ce/Zr ratios,forming a Cu^(+)-O_(v)-Ce^(3+)structure where Cu^(+)atoms are bonded to the oxygen vacancies(O_(v))of ceria.Compared to Cu/CeO_(2) and Cu/ZrO_(2),the optimized catalyst(i.e.,Cu_(0.3)Ce_(0.3)Zr_(0.7))exhibits a much higher mass-specific methanol formation rate(192g_(MeOH)/kg_(cat)/h)at 240℃and 3 MPa.Through a series of in-situ and ex-situ characterization,it is revealed that oxygen vacancies in solid solutions can effectively assist the activation of CO_(2) and tune the electronic state of copper to promote the formation of Cu^(+)/CeZrO_(x) interfaces,which stabilizes the key*CO intermediate,inhibits its desorption and facilitates its further hydrogenation to methanol via the reverse watergas-shift(RWGS)+CO-Hydro pathway.Therefore,the concentration of*CO or the apparent Cu^(+)/(Cu^(+)+Cu^(0))ratio could be employed as a quantitative descriptor of the methanol formation rate.This work is expected to give a deep insight into the mechanism of metal/support interfaces in CO_(2) hydrogenation to methanol,offering an effective strategy to develop new catalysts with high performance.展开更多
The electrochemical hydrogenation of HMF to BHMF is an elegant alternative to the conventio nal thermocatalytic route for the production of high-value-added chemicals from biomass resources.In virtue of the wide poten...The electrochemical hydrogenation of HMF to BHMF is an elegant alternative to the conventio nal thermocatalytic route for the production of high-value-added chemicals from biomass resources.In virtue of the wide potential window with promising Faradic efficiency(FE) towards BHMF,Cu-based electrode has been in the center of investigation.However,its structure-activity relationship remains ambiguous and its intrinsic catalytic activity is still unsatisfactory.In this work,we develop a two-step oxidation-reduction strategy to reconstruct the surface atom arrangement of the Cu foam(CF).By combination of multiple quasi-situ/in-situ techniques and density functional theory(DFT) calculation,the critical factor that governs the reaction is demonstrated to be facet effect of the metallic Cu crystal:Cu(110) facet accounts for the most favorable surface with enhanced chemisorption with reactants and selective production of BHMF,while Cu(100) facet might trigger the accumulation of the by-product 5,5'-bis(hydroxy methy)hydrofurion(BHH).With the optimized composition of the facets on the reconstructed Cu(OH)_(2)-ER/CF,the performance could be noticeably enhanced with a BHMF FE of 92.3% and HMF conversion of 98.5% at a potential of -0.15 V versus reversible hydrogen electrode(vs.RHE) in 0.1 M KOH solution.This work sheds light on the incomplete mechanistic puzzle for Cu-catalyzed electrochemical hydrogenation of HMF to BHMF,and provides a theoretical foundation for further precise design of highly efficient catalytic electrodes.展开更多
Magnesium hydride(MgH_(2))is the most feasible and effective solid-state hydrogen storage material,which has excellent reversibility but initiates decomposing at high temperatures and has slow kinetics performance.Her...Magnesium hydride(MgH_(2))is the most feasible and effective solid-state hydrogen storage material,which has excellent reversibility but initiates decomposing at high temperatures and has slow kinetics performance.Here,zinc titanate(Zn_(2)TiO_(4))synthesised by the solid-state method was used as an additive to lower the initial temperature for dehydrogenation and enhance the re/dehydrogenation behaviour of MgH_(2).With the presence of Zn_(2)TiO_(4),the starting temperature for the dehydrogenation of MgH_(2)was remarkably lowered to around 290℃–305℃.In addition,within 300 s,the MgH_(2)–Zn_(2)TiO_(4)sample absorbed 5.0 wt.%of H_(2)and 2.2–3.6 wt.%H_(2)was liberated from the composite sample in 30 min,which is faster by 22–36 times than as-milled MgH_(2).The activation energy of the MgH_(2)for the dehydrogenation process was also downshifted to 105.5 k J/mol with the addition of Zn_(2)TiO_(4)indicating a decrease of 22%than as-milled MgH_(2).The superior behaviour of MgH_(2)was due to the formation of Mg Zn_(2),MgO and MgTiO_(3),which are responsible for ameliorating the re/dehydrogenation behaviour of MgH_(2).These findings provide a new understanding of the hydrogen storage behaviour of the catalysed-MgH_(2)system.展开更多
Production of light olefins from CO_(2), the primary greenhouse gases, is of great importance to mitigate the adverse effects of CO_(2) emission on environment and to supply the value-added products from nonpetroleum ...Production of light olefins from CO_(2), the primary greenhouse gases, is of great importance to mitigate the adverse effects of CO_(2) emission on environment and to supply the value-added products from nonpetroleum resource. However, development of robust catalyst with controllable selectivity and stability remains a challenge. Herein, we report that Zn-promoted Fe catalyst can boost the stable and selective production of light olefins from CO_(2). Specifically, the Zn-promoted Fe exhibits a highly stable activity and olefin selectivity over 200 h time-on-stream compared to the unpromoted Fe catalyst, primarily owing to the preservation of active χ-Fe_(5)C_(2) phase. Structural characterizations of the spent catalysts suggest that Zn substantially regulates the content of iron carbide on the surface and suppresses the reoxidation of bulk iron carbide during the reaction. DFT calculations confirm that adsorption of surface carbon atoms and graphene-like carbonaceous species are not thermochemically favored on Zn-promoted Fe catalyst. Carbon deposition by CAC coupling reactions of two surface carbon atoms and dehydrogenation of CH intermediate are also inhibited. Furthermore, the effects of Zn on antioxidation of iron carbide were also investigated. Zn favored the hydrogenation of surface adsorbed oxygen atoms to H_(2)O and the desorption of H_(2)O, which reduces the possibility of surface carbide being oxidized by the chemisorbed oxygen.展开更多
The promoting effect of zirconium addition on Pd/Beta catalysts has been investigated in the selective hydrogenation of phenol to cyclohexanone in the aqueous phase. The activity of the catalyst in the reaction was gr...The promoting effect of zirconium addition on Pd/Beta catalysts has been investigated in the selective hydrogenation of phenol to cyclohexanone in the aqueous phase. The activity of the catalyst in the reaction was greatly improved by introducing Zr atoms into the framework of H-Beta zeolite. An important synergy between the Zr species and Pd, affecting the Pd dispersion state on the support, has been observed. The modification of the support with Zr^(4+) improves the Lewis/Brφnsted acid ratio of the catalyst, suppressing the further transformation of cyclohexanone. The kinetics of Pd/Zr-Beta catalyst showed high selectivity to cyclohexanone. The catalytic results showed that the Pd/Zr-Beta had the best catalytic performance at the desired temperature of 80℃ for 5 h.展开更多
The liquid phase selective hydrogenation of cinnamaldehyde has been investigated over the catalysts Co-C-T(T=400-700℃),which were derived from the carbonization of the MOF precursor Co-BTC at different temperatures i...The liquid phase selective hydrogenation of cinnamaldehyde has been investigated over the catalysts Co-C-T(T=400-700℃),which were derived from the carbonization of the MOF precursor Co-BTC at different temperatures in inert atmosphere.Co-C-500 exhibited a higher conversion(85.3%)than those carbonized at other temperatures,with 51.5%selectivity to cinnamyl alcohol,under a mild condition(90℃,4 h,2 MPa H_(2),solvent:9 ml ethanol and 1 ml water).The high catalytic activity of Co-C-500 can be ascribed to the large specific surface area of the catalyst,the uniformly dispersed metallic cobalt nanoparticles,and the more defect sites on the carbon support.Moreover,Co-C-500 showed excellent reusability in 5 successive cycles,mainly related to the uniformly dispersed cobalt nanoparticles embedded in carbon support.展开更多
The different reservoirs in deep Songliao Basin have non-homogeneous lithologies and include multiple layers with a high content of hydrogen gas.The gas composition and stable isotope characteristics vary significantl...The different reservoirs in deep Songliao Basin have non-homogeneous lithologies and include multiple layers with a high content of hydrogen gas.The gas composition and stable isotope characteristics vary significantly,but the origin analysis of different gas types has previously been weak.Based on the geochemical parameters of gas samples from different depths and the analysis of geological settings,this research covers the diverse origins of natural gas in different strata.The gas components are mainly methane with a small amount of C_(2+),and non-hydrocarbon gases,including nitrogen(N_(2)),hydrogen(H_(2)),carbon dioxide(CO_(2)),and helium(He).At greater depth,the carbon isotope of methane becomes heavier,and the hydrogen isotope points to a lacustrine sedimentary environment.With increasing depth,the origins of N_(2)and CO_(2)change gradually from a mixture of organic and inorganic to inorganic.The origins of hydrogen gas are complex and include organic sources,water radiolysis,water-rock(Fe^(2+)-containing minerals)reactions,and mantle-derived.The shales of Denglouku and Shahezi Formations,as source rocks,provide the premise for generation and occurrence of organic gas.Furthermore,the deep faults and fluid activities in Basement Formation control the generation and migration of mantle-derived gas.The discovery of a high content of H_(2)in study area not only reveals the organic and inorganic association of natural-gas generation,but also provides a scientific basis for the exploration of deep hydrogen-rich gas.展开更多
基金support from National Key Research and Development Program of China(2021YFC2103701)the National Postdoctoral Program of China(GZB20230630)the National Natural Science Foundation of China(22208295).
文摘Understanding the relationship between the chemical composition and pyrolysis performance of endothermic hydrocarbon fuel(EHF) is of great significance for the design and optimization of advanced EHFs. In this work, the effect of deep hydrogenation on the pyrolysis of commercial RP-3 is investigated.Fuels with different hydrogenation degrees were obtained by the partially and completely catalytic hydrogenation and their pyrolysis performances were investigated using an apparatus equipped with an electrically heated tubular reactor. The results show that with the increase of hydrogenation degree, fuel conversion almost remains constant during the pyrolysis process(500-650°C, 4 MPa);however, the heat sink increases slightly, and the anti-coking performance significantly improves, which are highly related to their H/C ratios. Detailed characterisations reveal that the difference of the pyrolysis performance can be ascribed to the content of aromatics and cycloalkanes: the former are prone to initiate secondary reactions to form coking precursors, while the latter could act as the hydrogen donor and release hydrogen, which will terminate the radical propagation reactions and suppress the coke deposition. This work should provide the guidance for upgrading EHFs by modulating the composition of EHFs.
基金support by the National Natural Science Foundation of China under Grant No.U20A20237 and the High Performance Computing Center of Central South University are gratefully acknowledged.
文摘Magnesium hydride is one of the most promising solid-state hydrogen storage materials for on-board application.Hydrogen desorption from MgH_(2) is accompanied by the formation of the Mg/MgH_(2) interfaces,which may play a key role in the further dehydrogenation process.In this work,first-principles calculations have been used to understand the dehydrogenation properties of the Mg(0001)/MgH_(2)(110) interface.It is found that the Mg(0001)/MgH_(2)(110) interface can weaken the Mg-H bond.The removal energies for hydrogen atoms in the interface zone are significantly lower compared to those of bulk MgH_(2).In terms of H mobility,hydrogen diffusion within the interface as well as into the Mg matrix is considered.The calculated energy barriers reveal that the migration of hydrogen atoms in the interface zone is easier than that in the bulk MgH_(2).Based on the hydrogen removal energies and diffusion barriers,we conclude that the formation of the Mg(0001)/MgH_(2)(110) interface facilitates the dehydrogenation process of magnesium hydride.
基金supported by grants from the National Key Research and Development Program of China(2023YE41507601)the National Natural Science Foundation of China(22122807,22378038)+1 种基金the Fundamental Research Funds for the Central Universities(DUT23RC(3)044)State Key Laboratory of Heavy Oil Processing,China University of Petroleum(WX20230149)。
文摘Industrial catalyst waste has emerged as a hazardous pollutant that requires safe and proper disposal after the unloading process.Finding a valuable and sustainable strategy for its treatment is a significant challenge compared to traditional methods.In this study,we present a facile method for the recovery of molybdenum and aluminum contents from spent Mo-Ni/Al_(2)O_(3) hydrogenation catalysts through crystallization separation and coprecipitation.Furthermore,the recovered molybdenum and aluminum are utilized as active metals and carriers for the preparation of new catalysts.Their properties were thoroughly analyzed and investigated using various characterization techniques.The hydrogenation activity of these newly prepared catalysts was evaluated on a fixed-bed small-scale device and compared with a reference catalyst synthesized from commercial raw reagents.Finally,the hydrogenation activity of the catalysts was further assessed by using the entire distillate oil of coal liquefaction as the raw oil,specifically focusing on denitrogenation and aromatic saturation.This work not only offers an effective solution for recycling catalysts but also promotes sustainable development.
基金supported by the National Key R&D Program of China(2023YFD1701504)the 2115 Talent Development Program of China Agricultural University Fund(1011-00109018)the Beijing Innovation Team of the Modern Agricultural Research System(BAIC08-2023-FQ02)。
文摘Optimizing the intrinsic activity of non-noble metal by precisely tailoring electronic structure offers an appealing way to construct cost-effective catalysts for selective biomass valorization.Herein,we reported a P-doping bifunctional catalyst(Ni-P/mSiO_(2))that achieved 96.6%yield for the hydrogenation rearrangement of furfural to cyclopentanone at mild conditions(1 MPaH_(2),150°C).The turnover frequency of Ni-P/mSiO_(2)was 411.9 h^(-1),which was 3.2-fold than that of Ni/mSiO_(2)(127.2 h^(-1)).Detailed characterizations and differential charge density calculations revealed that the electron-deficient Niδ+species were generated by the electron transfer from Ni to P,which promoted the ring rearrangement reaction.Density functional theory calculations illustrated that the presence of P atoms endowed furfural tilted adsorb on the Ni surface by the C=O group and facilitated the desorption of cyclopentanone.This work unraveled the connection between the localized electronic structures and the catalytic properties,so as to provide a promising reference for designing advanced catalysts for biomass valorization.
基金supported by the Research Intensified Grant Scheme (RIGS) under grant number VOT 55440 provided by Universiti Malaysia Terengganu (UMT)the SIPP Incentive sponsored by UMT
文摘For the first time,the MgH_(2)–NaAlH_(4)(ratio 4:1)destabilized system with CoTiO_(3) addition has been explored.The CoTiO_(3)-doped MgH_(2)–NaAlH_(4) sample begins to dehydrogenate at 130℃,which is declined by 40℃ compared to the undoped MgH_(2)–NaAlH_(4).Moreover,the de/rehydrogenation kinetics characteristics of the CoTiO_(3)-doped MgH_(2)–NaAlH_(4) were greatly ameliorated.With the inclusion of CoTiO_(3),the MgH_(2)–NaAlH_(4) composite absorbed 5.2 wt.%H_(2),higher than undoped MgH_(2)–NaAlH_(4).In the context of dehydrogenation,the CoTiO_(3)-doped MgH_(2)–NaAlH_(4) sample desorbed 2.6 wt.%H_(2),almost doubled compared to the amount of hydrogen desorbed from the undoped MgH_(2)–NaAlH_(4) sample.The activation energy obtained by the Kissinger analysis for MgH_(2) decomposition was significantly lower by 35.9 kJ/mol than the undoped MgH_(2)–NaAlH_(4) sample.The reaction mechanism demonstrated that new phases of MgCo and AlTi_(3) were generated in situ during the heating process and are likely to play a substantial catalytic function and be useful in ameliorating the de/rehydrogenation properties of the destabilized MgH_(2)–NaAlH_(4) system with the inclusion of CoTiO_(3).
基金the financial support from the Sinopec Catalyst Co.Ltd.,China。
文摘A series of model catalysts were obtained by treating commercial fresh and spent catalysts unloaded from the factory with different methods, including green oil dipping, extraction and high-temperature regeneration;finally, the deactivation behavior of the commercial catalyst for acetylene hydrogenation were studied. The influence of various possible deactivation factors on the catalytic performance was elucidated via detailed structural characterization, surface composition analysis, and activity evaluation.The results showed that green oil, carbon deposit and sintering of active metal were the main reasons for deactivation, among which green oil and carbon deposit led to rapid deactivation, while the activity could be recovered after regeneration by high-temperature calcination. The sintering of active metal components was attributed to the high-temperature regeneration in hydrothermal conditions, which was slow but irreversible and accounted for permanent deactivation. Thus, optimizing the regeneration is expected to extend the service life of the commercial catalyst.
文摘Catalysts with varying Fe contents were prepared using a sequential impregnation method to investigate the effects of Fe addition on the physicochemical properties of Pt/Al_(2)O_(3) and their performance in methylcyclohexane(MCH)dehydrogenation.The results demonstrated that the addition of Fe to Pt/Al_(2)O_(3) enhanced the electron density of Pt and improved catalytic activity,while exhibiting negligible influence on the catalytic selectivity for toluene.When the Fe content was 0.057%,the catalyst exhibited the highest MCH consumption rate,which was approximately two times higher than that of the catalyst without Fe.Additionally,the incorporation of Fe inhibited the formation of coke and reduced the quantity of coke deposits on the catalyst,thereby improving its catalytic durability.Overall,Fe shows promise as a prospective secondary element for Pt/Al_(2)O_(3) to enhance the MCH dehydrogenation performance.
基金financially supported by National Natural Science Foundation of China (Nos. 12075032 and 12105021)Beijing Municipal Natural Science Foundation (Nos.8222055 and 2232061)+1 种基金Yunnan Police College Project (No. YJKF002)Beijing Institute of Graphic Communication Project (No. Ec202207)。
文摘Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is reported to fabricate Pd nanoparticle catalyst over γ-Al_(2)O_(3)or Fe_(2)O_(3)/γ-Al_(2)O_(3)support,using palladium hexafluoroacetylacetonate as the Pd precursor and H_(2)plasma as counter-reactant.Scanning transmission electron microscopy exhibits that highdensity Pd nanoparticles are uniformly dispersed over Fe_(2)O_(3)/γ-Al_(2)O_(3)support with an average diameter of 4.4 nm.The deposited Pd-Fe_(2)O_(3)/γ-Al_(2)O_(3)shows excellent catalytic performance for CO_(2)hydrogenation in a dielectric barrier discharge reactor.Under a typical condition of H_(2)to CO_(2)ratio of 4 in the feed gas,the discharge power of 19.6 W,and gas hourly space velocity of10000 h^(-1),the conversion of CO_(2)is as high as 16.3% with CH_(3)OH and CH4selectivities of 26.5%and 3.9%,respectively.
基金supported by the National Natural Science Foundation of China(22138009)the Fundamental Research Funds for the Central Universities of China。
文摘The metal promoted In_(2)O_(3) catalysts for CO_(2) hydrogenation to methanol have attracted wide attention because of their high activity with high methanol selectivity.However,there was still no experimental confirmation if copper could be a good promoter for In_(2)O_(3).Herein,the Cu promoted In_(2)O_(3) catalyst was prepared using a deposition-precipitation method.Such prepared Cu/In_(2)O_(3) catalyst shows significantly higher CO_(2) conversion and space time yield(STY)of methanol,compared to the un-promoted In_(2)O_(3) catalyst.The loading of Cu facilitates the activation of both H_(2) and CO_(2) with the interface between the Cu cluster and defective In_(2)O_(3) as the active site.The Cu/In_(2)O_(3) catalyst takes the CO hydrogenation pathway for methanol synthesis from CO_(2) hydrogenation.It exhibits a unique size effect on the CO adsorption.At temperatures below 250℃,CO adsorption on Cu/In_(2)O_(3) is stronger than that on In_(2)O_(3),causing higher methanol selectivity.With increasing temperatu res,the Cu catalyst aggregates,which leads to the formation of weak CO adsorption site and causes a decrease in the methanol selectivity.Compared with other metal promoted In_(2)O_(3) catalysts,it can be concluded that the catalyst with stronger CO adsorption possesses higher methanol selectivity.
基金the National Natural Science Foundation of China(Nos.61973223,51972306)the Liao Ning Revitalization Talents Program(No.XLYC2007051)+2 种基金the Liaoning Educational Department Foundation(No.LJKMZ20220762,JYTMS20231510)the Natural Science Foundation of Liaoning Province(No.2023-MS-235,2023-MSLH-270)the Key Project in Science&Technology of SYUCT(No.2023DB005).
文摘Cu/ZnO is widely used in the hydrogenation of carbon dioxide (CO_(2)) to methanol (CH_(3)OH) to improve the lowconversion rate and selectivity generally observed. In this work, a series of In, Zr, Co, and Ni-doped CuO-ZnO catalysts wassynthesized via a hydrothermal method. By introducing a second metal element, the activity and dispersion of the activesites can be adjusted and the synergy between the metal and the carrier can be enhanced, forming an abundance of oxygenvacancies. Oxygen vacancies not only adsorb CO_(2) but also activate the intermediates in methanol synthesis, playing a keyrole in the entire reaction. Co3O4-CuO-ZnO had the best catalytic performance (a CO_(2) conversion rate of 9.17%;a CH_(3)OHselectivity of 92.77%). This study describes a typical strategy for multi-component doping to construct a catalyst with anabundance of oxygen vacancies, allowing more effective catalysis to synthesize CH_(3)OH from CO_(2).
基金supported by National Key Research&Development Program of China(2021YFB3801600)Fundamental Research Funds for the Central University(buctrc201921,JD2223,12060093063)Innovative Achievement Commercialization Service-Platform of Industrial Catalysis(2019-00900-2-1).
文摘Alumina(Al_(2)O_(3))is widely used in the chemical industry as the catalyst and support due to its high specific surface area,abundant pore size distribution and chemical stability.However,the occurrence of hydration in water environment,result in outstanding decrease in specific surface area and collapse of pore structure.In this work,dodecyl phosphoric acid(PA)is used to modify the surface of Al_(2)O_(3)to obtain a series of hydrophobic material(Al_(2)O_(3)-PA).Based on XPS and NMR analysis,PA is chemically bonded on Al_(2)O_(3)to form PAOAAl bond.Furthermore,BET and WCA results display that Al_(2)O_(3)-1PA exhibits excellent the hydrophobicity and hydrothermal stability while maintains the pore structure.Take it as the substrate to support the Pd nanoparticles,the as-prepared Pd/Al_(2)O_(3)-PA shows the superior catalytic performance in the hydrogenation of phenol and anthraquinone relative to Pd/Al_(2)O_(3),indicating the accessibility of Pd sites after PA modification.Especially,the significantly enhanced stability is also obtained in four cycles for aqueous phenol hydrogenation.This can be ascribed that the PA modification inhibits the aggregation of Pd nanoparticles and the products adhesion in the reaction process.The extension of PA coatings to monolithic catalysts could expand their current capabilities in industrial applications and warrants ongoing investigation.
基金supported by National Natural Science Foundation of China(Nos.22108200,21938008 and 22121004)Natural Science Foundation of Zhejiang Province(LQ22B060013)the Haihe Laboratory of Sustainable Chemical Transformations for financial support。
文摘The interaction between a promoter and an active metal crucially impacts catalytic performance.Nowadays,the influence of promoter contents and species has been intensively considered.In this study,we investigate the effect of the iron(Fe)-zinc(Zn)proximity of Fe-Zn bimetallic catalysts on CO_(2)hydrogenation performance.To eliminate the size effect,Fe_(2)O_(3)and ZnO nanoparticles with uniform size are first prepared by the thermal decomposition method.By changing the loading sequence or mixing method,a series of Fe-Zn bimetallic catalysts with different Fe-Zn distances are obtained.Combined with a series of characterization techniques and catalytic performances,Fe-Zn bimetallic proximity for compositions of Fe species is discussed.Furthermore,we observe that a smaller Fe-Zn distance inhibits the reduction and carburization of the Fe species and facilitates the oxidation of carbides.Appropriate proximity of Fe and Zn(i.e.,Fe_1Zn_(1)-imp and Fe_(1)Zn_(1)-mix samples)results in a suitable ratio of the Fe_5C_(2)and Fe_(3)O_(4)phases,simultaneously promoting the reverse water-gas shift and Fischer-Tropsch synthesis reactions.This study provides insight into the proximity effect of bimetallic catalysts on CO_(2)hydrogenation performance.
基金supported by the National Natural Science Foundation of China(21802138,21773234 and 22078315)the‘‘Transformational Technologies for Clean Energy and Demonstration’’,Strategic Priority Research Program of the Chinese Academy of Sciences(XDA 21090203)+3 种基金the Youth Innovation Promotion Association of Chinese Academy of Sciences(2020189)the Natural Science Foundation of Liaoning Province(2022-MS-027)the Youth Science and Technology Star Project Support Program of Dalian City(2021RQ123),DICP(Grant:DICP I202138)the University of Chinese Academy of Sciences(UCAS)for UCAS Scholarship。
文摘CO_(2)hydrogenation has been considered to be a highly promising route for the production of high-value olefins(HVOs)while also mitigating CO_(2)emissions.However,it is challenging to achieve high selectivity and maintain stable performance for HVOs(ethylene,propylene,and linear a-olefins)over a prolonged reaction time due to the difficulty in precise control of carbon coupling and rapid catalyst deactivation.Herein,we present a selective Ba and Na co-modified Fe catalyst enriched with Fe_(5)C_(2)and Fe_(3)C active sites that can boost HVO synthesis with up to 66.1%selectivity at an average CO_(2)conversion of 38%for over 500 h.Compared to traditional NaFe catalyst,the combined effect of Ba and Na additives in the NaBaFe-0.5 catalyst suppressed excess oxidation of FeCxsites by H_(2)O.The absence of Fe3O4phase in the spent NaBaFe-0.5 catalyst reflects the stabilization effect of the co-modifiers on the FeCxsites.This study provides a strategy to design Fe-based catalysts that can be scaled up for the stable synthesis of HVOs from CO_(2)hydrogenation.
基金sponsored by the National Natural Science Foundation of China(21808120,21978148)。
文摘Cu-based catalysts are widely employed for CO_(2) hydrogenation to methanol,which is expected as a promising process to achieving carbon neutrality.However,most Cu-based catalysts still suffer from low methanol yield with a passable CO_(2) conversion and lack insight into its reaction mechanism for guiding the design of catalysts.In this work,Cu^(+)/CeZrO_(x) interfaces are engineered by employing a series of ceria-zirconia solid solution catalysts with various Ce/Zr ratios,forming a Cu^(+)-O_(v)-Ce^(3+)structure where Cu^(+)atoms are bonded to the oxygen vacancies(O_(v))of ceria.Compared to Cu/CeO_(2) and Cu/ZrO_(2),the optimized catalyst(i.e.,Cu_(0.3)Ce_(0.3)Zr_(0.7))exhibits a much higher mass-specific methanol formation rate(192g_(MeOH)/kg_(cat)/h)at 240℃and 3 MPa.Through a series of in-situ and ex-situ characterization,it is revealed that oxygen vacancies in solid solutions can effectively assist the activation of CO_(2) and tune the electronic state of copper to promote the formation of Cu^(+)/CeZrO_(x) interfaces,which stabilizes the key*CO intermediate,inhibits its desorption and facilitates its further hydrogenation to methanol via the reverse watergas-shift(RWGS)+CO-Hydro pathway.Therefore,the concentration of*CO or the apparent Cu^(+)/(Cu^(+)+Cu^(0))ratio could be employed as a quantitative descriptor of the methanol formation rate.This work is expected to give a deep insight into the mechanism of metal/support interfaces in CO_(2) hydrogenation to methanol,offering an effective strategy to develop new catalysts with high performance.
基金supported by the National Natural Science Foundation of China (21808035, 21901040)the Natural Science Foundation of Fujian Province (2019J05058, 2021J05216, 2022J01922)+3 种基金the Fujian Provincial Department of Finance (GY-Z220231)the fund of the State Key Laboratory of Catalysis in DICP (N-22-08)the Fujian Fishery Disaster Reduction Center (GY-H-22146)College Student Innovation and Entrepreneurship Training Program (x202110388068)。
文摘The electrochemical hydrogenation of HMF to BHMF is an elegant alternative to the conventio nal thermocatalytic route for the production of high-value-added chemicals from biomass resources.In virtue of the wide potential window with promising Faradic efficiency(FE) towards BHMF,Cu-based electrode has been in the center of investigation.However,its structure-activity relationship remains ambiguous and its intrinsic catalytic activity is still unsatisfactory.In this work,we develop a two-step oxidation-reduction strategy to reconstruct the surface atom arrangement of the Cu foam(CF).By combination of multiple quasi-situ/in-situ techniques and density functional theory(DFT) calculation,the critical factor that governs the reaction is demonstrated to be facet effect of the metallic Cu crystal:Cu(110) facet accounts for the most favorable surface with enhanced chemisorption with reactants and selective production of BHMF,while Cu(100) facet might trigger the accumulation of the by-product 5,5'-bis(hydroxy methy)hydrofurion(BHH).With the optimized composition of the facets on the reconstructed Cu(OH)_(2)-ER/CF,the performance could be noticeably enhanced with a BHMF FE of 92.3% and HMF conversion of 98.5% at a potential of -0.15 V versus reversible hydrogen electrode(vs.RHE) in 0.1 M KOH solution.This work sheds light on the incomplete mechanistic puzzle for Cu-catalyzed electrochemical hydrogenation of HMF to BHMF,and provides a theoretical foundation for further precise design of highly efficient catalytic electrodes.
基金Universiti Malaysia Terengganu(UMT)for the funding provided by Golden Goose Research Grant(GGRG)VOT 55190。
文摘Magnesium hydride(MgH_(2))is the most feasible and effective solid-state hydrogen storage material,which has excellent reversibility but initiates decomposing at high temperatures and has slow kinetics performance.Here,zinc titanate(Zn_(2)TiO_(4))synthesised by the solid-state method was used as an additive to lower the initial temperature for dehydrogenation and enhance the re/dehydrogenation behaviour of MgH_(2).With the presence of Zn_(2)TiO_(4),the starting temperature for the dehydrogenation of MgH_(2)was remarkably lowered to around 290℃–305℃.In addition,within 300 s,the MgH_(2)–Zn_(2)TiO_(4)sample absorbed 5.0 wt.%of H_(2)and 2.2–3.6 wt.%H_(2)was liberated from the composite sample in 30 min,which is faster by 22–36 times than as-milled MgH_(2).The activation energy of the MgH_(2)for the dehydrogenation process was also downshifted to 105.5 k J/mol with the addition of Zn_(2)TiO_(4)indicating a decrease of 22%than as-milled MgH_(2).The superior behaviour of MgH_(2)was due to the formation of Mg Zn_(2),MgO and MgTiO_(3),which are responsible for ameliorating the re/dehydrogenation behaviour of MgH_(2).These findings provide a new understanding of the hydrogen storage behaviour of the catalysed-MgH_(2)system.
基金the funding support from Shanghai Sailing Program (19YF1411000)National Natural Science Foundation of China (21878080, 21808058)Ningxia Science Foundation (2019AAC03282)。
文摘Production of light olefins from CO_(2), the primary greenhouse gases, is of great importance to mitigate the adverse effects of CO_(2) emission on environment and to supply the value-added products from nonpetroleum resource. However, development of robust catalyst with controllable selectivity and stability remains a challenge. Herein, we report that Zn-promoted Fe catalyst can boost the stable and selective production of light olefins from CO_(2). Specifically, the Zn-promoted Fe exhibits a highly stable activity and olefin selectivity over 200 h time-on-stream compared to the unpromoted Fe catalyst, primarily owing to the preservation of active χ-Fe_(5)C_(2) phase. Structural characterizations of the spent catalysts suggest that Zn substantially regulates the content of iron carbide on the surface and suppresses the reoxidation of bulk iron carbide during the reaction. DFT calculations confirm that adsorption of surface carbon atoms and graphene-like carbonaceous species are not thermochemically favored on Zn-promoted Fe catalyst. Carbon deposition by CAC coupling reactions of two surface carbon atoms and dehydrogenation of CH intermediate are also inhibited. Furthermore, the effects of Zn on antioxidation of iron carbide were also investigated. Zn favored the hydrogenation of surface adsorbed oxygen atoms to H_(2)O and the desorption of H_(2)O, which reduces the possibility of surface carbide being oxidized by the chemisorbed oxygen.
基金Financial supports from the State Key Laboratory of Catalytic Materials and Reaction Engineering (RIPP, SINOPEC)。
文摘The promoting effect of zirconium addition on Pd/Beta catalysts has been investigated in the selective hydrogenation of phenol to cyclohexanone in the aqueous phase. The activity of the catalyst in the reaction was greatly improved by introducing Zr atoms into the framework of H-Beta zeolite. An important synergy between the Zr species and Pd, affecting the Pd dispersion state on the support, has been observed. The modification of the support with Zr^(4+) improves the Lewis/Brφnsted acid ratio of the catalyst, suppressing the further transformation of cyclohexanone. The kinetics of Pd/Zr-Beta catalyst showed high selectivity to cyclohexanone. The catalytic results showed that the Pd/Zr-Beta had the best catalytic performance at the desired temperature of 80℃ for 5 h.
基金financial support from the National Natural Science Foundation of China(22272016).
文摘The liquid phase selective hydrogenation of cinnamaldehyde has been investigated over the catalysts Co-C-T(T=400-700℃),which were derived from the carbonization of the MOF precursor Co-BTC at different temperatures in inert atmosphere.Co-C-500 exhibited a higher conversion(85.3%)than those carbonized at other temperatures,with 51.5%selectivity to cinnamyl alcohol,under a mild condition(90℃,4 h,2 MPa H_(2),solvent:9 ml ethanol and 1 ml water).The high catalytic activity of Co-C-500 can be ascribed to the large specific surface area of the catalyst,the uniformly dispersed metallic cobalt nanoparticles,and the more defect sites on the carbon support.Moreover,Co-C-500 showed excellent reusability in 5 successive cycles,mainly related to the uniformly dispersed cobalt nanoparticles embedded in carbon support.
基金supported by the National Natural Science Foundation of China(Grant No.42072168)the National Key R&D Program of China(Grant No.2019YFC0605405)the Fundamental Research Funds for the Central Universities(Grant No.2023ZKPYDC07)。
文摘The different reservoirs in deep Songliao Basin have non-homogeneous lithologies and include multiple layers with a high content of hydrogen gas.The gas composition and stable isotope characteristics vary significantly,but the origin analysis of different gas types has previously been weak.Based on the geochemical parameters of gas samples from different depths and the analysis of geological settings,this research covers the diverse origins of natural gas in different strata.The gas components are mainly methane with a small amount of C_(2+),and non-hydrocarbon gases,including nitrogen(N_(2)),hydrogen(H_(2)),carbon dioxide(CO_(2)),and helium(He).At greater depth,the carbon isotope of methane becomes heavier,and the hydrogen isotope points to a lacustrine sedimentary environment.With increasing depth,the origins of N_(2)and CO_(2)change gradually from a mixture of organic and inorganic to inorganic.The origins of hydrogen gas are complex and include organic sources,water radiolysis,water-rock(Fe^(2+)-containing minerals)reactions,and mantle-derived.The shales of Denglouku and Shahezi Formations,as source rocks,provide the premise for generation and occurrence of organic gas.Furthermore,the deep faults and fluid activities in Basement Formation control the generation and migration of mantle-derived gas.The discovery of a high content of H_(2)in study area not only reveals the organic and inorganic association of natural-gas generation,but also provides a scientific basis for the exploration of deep hydrogen-rich gas.