Method for predicting motion artifacts of plasma display panels

A simulation method is proposed to predict the motion artifacts of plasma display panels （PDPs）. The method simulates the behavior of the human vision system when perceiving moving objects. The simulation is based on the measured temporal light properties of the display for each gray level and each phosphor. Both the effect of subfield arrangement and phosphor decay are involved. A novel algorithm is proposed to improve the calculation speed. The simulation model manages to predict the appearance of the motion image perceived by a human with a still image. The results are validated by a set of perceptual evaluation experiments. This rapid and accurate prediction of motion artifacts enables objective characterization of the PDP performance in this aspect.

Increase of brightness and transmission efficiency in fiat panel display through serial synchronous scanning mode with double buffers

This paper presents a serial synchronous scanning mode in fiat panel display （FPD） by adding a latch buffer between the serializer and the driving buffer. Comparing with conventional techniques, the proposed structure can efficiently reduce the brightness loss and improve the transmission performance. Theoretical analysis and experimental results show that the ratio between the lightest weight display time and the relative transmission time is a tradeoff between brightness loss and transmission efficiency.

Simulation Studies of Rib Structure Effect on Discharge Characteristics of Plasma Display Panel

To investigate the effect of the rib structure on the discharge characteristics of the plasma display panel, the potential distribution, particles density distribution and ions incident angle distribution were examined by simulation of a two-dimensional particle-in-cell/Monte Carlo collision, with two kinds of rib structure： the stripe rib structure and the Waffle rib structure. The results showed that the distribution of electric potential at the corner of the discharge cell was almost the same for these two rib structures while in the centre there was a difference between these two rib structures. The striation phenomenon could be observed in both cases. The distribution of density also indicated that the striation phenomenon was accompanied by the firing of discharge, and the Waffle rib structure might reduce the density humps. In the cell with a stripe rib structure, the profiles of the surface charge density along the sustained dielectric layer presented a better fluctuating distribution than that in the cell with a Waffle rib structure. The spatial potential and particle density in the discharge bulk showed that the Waffle ribs could weaken the striation phenomenon, which could be explained by the decrease in the particle numbers in the discharge cell. The simulation results of the ion incident angle showed that most ions impacted the sustained dielectric layer in the normal stripe rib cell with an incident angle in the range of 6° to 19° while with the Waffle rib structure the incident angle of most ions was in the range of 4° to 19°. The Waffle rib structure did not affect the angle distribution of incident ions significantly.

Systematic studies on scan and driving model for flat panel display

Aiming at the time redundancy in the fiat panel display （FPD） imaging process, the paper studied some problems for FPD gray scale controlling based on the fraetal theory, dissertates the construction of the space-time mapping topology architecture, the proposition of optimal scanning structure for FPD＇s gray imaging, and the creation of the fractal theoretic model. Then the logic implementation and system application are presented based on the fraetal model of the optimal scan architecture, and the application results achieved target of eliminating time redundancy and increasing the scanning availability. The novel control mode that the fractal scanning IP core described with Verilog language embedded in the FPGA hardware frame can efficiently increase the imaging gray scales and quality in the FPDs scanning controller and speed up the frame frequency of display system.

Breakdown Voltage Research of Penning Gas Mixture in Plasma Display Panel

Paschen law and equations, which ignore the influence of the Penning ionization on the electron ionization coefficient （α）, are always used as the approximation of the breakdown voltage criterion of the Penning gas mixture in current researches of discharge characteristics of the plasma display panel （PDP）. It is doubtful that whether their results match the facts. Based on the Townsend gas self-sustaining discharge condition and the chemical kinetics analysis of the Penning gas mixture discharging in PDP, the empirical equation to describe the breakdown of the Penning gas mixture is given. It is used to calculate the breakdown voltage curves of Ne-Xe/MgO and Ne-Ar/MgO in a testing macroscopic discharge cell of AC-PDP. The effective secondary electron emission coefficients （γeff） of the MgO protective layers are derived by comparing the breakdown voltage curves obtained from the empirical equation with the experimental data of breakdown voltages. In comparison with the results calculated by the Paschen law and the equation which ignore the influence of the Penning ionization on α , the results calculated by the empirical equation have better conformity with experimental data. The empirical equation characterizes the breakdown of the Penning gas mixture in PDP effectively, and gives a convenient way to study its breakdown characteristics and the secondary electron emission behaviors.

Effects of Xe Gas Content and Total Gas Pressure on the Discharge Characteristics of Colour Plasma Display Panels

The effects of the Xe gas content and total gas pressure on the discharge characteristics of colour plasma display panels including the sustaining voltage margin, white-field chromaticity, discharge time lag （DTL）, discharge current peak, and full-width-at-half-maximum （FWHM） of the discharge current pulse, are experimentally studied. The results indicate that as the Xe gas content in the He-Ne-Xe gas mixture or total pressure increases, the sustaining voltage margin increases, the white-field chromaticity improves, and the discharge current peak has a maximum value, while DTL and FWHM have a minimum value. The mean electron energy in the gas mixture discharge is also calculated through a numerical solution of Boltzmann equation. The experimental results are explained from a view of the mean electron energy variations with the Xe gas content and total gas pressure.

CAS 132-2006 Standard for Flat Panel Display TV Set Installation Service Formulating and Enforcing Main Point Explanation and Analysis

CAS 132-2006 formulation background and work courses Flat panel display technology is maturing alongside the development of science and technology. The prices of flat panel display TV sets are becoming lower and lower. Flat panel display TV sets have begun entering the mainstream and are now the first choice of some consumers when making new TV purchases.Display TV Set Installation Service Point Explanation and AnalysisRepair, Retreat and Change Duty Stipulations. Peculiar use conditions, usage environments, and the practical circumstances of user consumption service requirements, etc., were also taken into account on the basis of extensive investigation, testing, and verification.……

Indium-gallium-zinc-oxide thin-film transistors:Materials,devices,and applications

Since the invention of amorphous indium-gallium-zinc-oxide(IGZO)based thin-film transistors(TFTs)by Hideo Hosono in 2004,investigations on the topic of IGZO TFTs have been rapidly expanded thanks to their high electrical performance,large-area uniformity,and low processing temperature.This article reviews the recent progress and major trends in the field of IGZO-based TFTs.After a brief introduction of the history of IGZO and the main advantages of IGZO-based TFTs,an overview of IGZO materials and IGZO-based TFTs is given.In this part,IGZO material electron travelling orbitals and deposition methods are introduced,and the specific device structures and electrical performance are also presented.Afterwards,the recent advances of IGZO-based TFT applications are summarized,including flat panel display drivers,novel sensors,and emerging neuromorphic systems.In particular,the realization of flexible electronic systems is discussed.The last part of this review consists of the conclusions and gives an outlook over the field with a prediction for the future.

Development of hydrometallurgical process for indium recovery from waste liquid crystal display using Cyphos IL 101

The main goal of this study was to recover indium from the waste liquid crystal display(LCD)panel.In this context,an ionic liquid Cyphos IL 101 was explored.The extraction parameters such as equilibration period,acid concentration,chloride ion concentration,hydrogen ion concentration were examined on the extraction efficiency of Cyphos IL 101 towards In(III).Quantitative extraction of indium was found at 2.0 mol/L HCl using 0.005 mol/L Cyphos IL 101 and quantitative stripping with 1.0 mol/L H2SO4.Job’s method was used to determine the extracted species and R3R'PInCl4(R=C6H13;R′=C14H29)was proposed.Based on the observations on multi-metal studies,Cyphos IL 101 was further employed for the removal of indium,tin and copper from the leach liquors of waste LCDs.Optimized conditions were generated for the recovery of indium from waste LCDs.McCabe−Thiele diagram analysis,counter-current extraction and selective stripping were carried out to separate the metal ions,i.e.,indium,tin and copper.Two stages at O/A ratio of 1:3 were required for complete removal of tin from the feed and selective stripping of In and Sn was achieved using 0.1 mol/L H2SO4.A scheme for separating indium from the waste LCDs was proposed.

Preparation and Luminescent Properties of BAM Blue Phosphor for PDP and CCFL

The Ba x-0.05MgAl 10O 16+x∶Eu 2+ 0.05 (0.88≤x ≤1.02) phosphors with different Ba 2+ content and the Ba 0.85MgAl 10O 16.94∶Eu 2+ 0.09 phosphors with different fluxes (BaF 2, MgF 2, AlF 3, BaCl 2, MgCl 2, AlCl 3, H 3BO 3) were prepared by high temperature solid-state reaction method and their luminescence characteristics were studied under 254 nm excitation and vacuum ultraviolet (VUV) excitation. With the increase of the Ba 2+ content, there is an increase in the emission intensity, and when x=0.94, it reaches a maximum. Then, as the Ba 2+ content increases, the emission intensity slowly falls. The fluorides have better flux-effects than chlorides and H 3BO 3. The possible mechanism in the process of particle growth was discussed when fluorides were used as fluxes. The effect of the activator concentration on this system was also investigated. The quenching concentration is 0.13 mol in per mole host.

Searching high gray scale FPD scanning matrix based on PSO

With the increase of gray scale and flat panel display （FPD） size, subspace bitwise scanning strategy can be replaced traditional scanning method to cut down frame frequency. However, the direct searching strategy （DSS） becomes unfeasible to obtain corresponding high gray scale scanning matrix. Thus, particle swarm optimization （PSO） is introduced to accelerate searching for high gray scale weights scanning matrix （WSM） with its parallelism and global optimization feature. Finally a WSM of 256 gray scales is found out successfully with Matlab, which both gray linearity and scanning efficiency are satisfied.

Numerical Simulation of the Discharge Efficiency in Five-electrode AC PDP

A new type of AC PDP(alternating current plasma display panel) cell with a five-electrode structure is developed to improve the luminous efficiency of AC PDP.The discharge efficiency of this new cell structure is investigated by a 2D fluid simulation. Continuity equations and flux density equations for charged particles and excited atoms, energy balance equation for electrons are included in the model. The discharge gas is He+5%Xe. The reactions of ionization, excitation, recombination, and radiation are taken into account. The vacuum ultraviolet radiation efficiency of the five-electrode cell structure is about 20% higher than that of a conventional three-electrode cell structure.

Investigation of Anode Striation in 34”VGA Shadow Mask PDP

A macro-cell was used to study the phenomenon of anode striation on a 34 VGA Shadow Mask Plasma Display Panel （SMPDP）. The breakdown process in the sustaining period of the macro-cell was taken by an Intensified Charge Coupled Device（ICCD） with narrow band filters. The mechanism of formation and evolution of the anode striation on SMPDP were investigated. The influence of the width of the electrode, the sustaining voltage, sustaining frequency and the voltage of the shadow mask on the anode striation was also studied. The results showed that the width of the electrodes, the sustaining voltage and frequency had a strong influence on the anode striation. The voltage of the shadow mask, however, hardly affected the anode striation, the firing voltage or the sustaining voltage.

Design on general development platform for FPD systems

In this paper, a multi-functional development platform for flat panel display （FPD） development is proposed. With the proposed development platforms, a variety of FPD devices, including organic light-emitting diode （OLED） screens, liquid crystal display （LCD） screens with touchscreens, OLED microdisplay screens, etc., can be directly and instantly connected, examined and utilized. A field-programmable gate array （FPGA） is used in the development system to drive different types of FPD devices, and ARM11S3C6410 is used as the application processor to provide various services. The development system uses Linux as the system kernel, Qt for Embedded Linux as the UI framework, various system libraries for video and audio services, and a custom-made user engine for fine-polished appearance and behavior. The development platform has been used not only in testing and verification of the FPD devices, but also in building OLED-powered handheld digital devices, shortening the development cycle from OLED devices to mature application products.

Research on High Discharge Efficiency in SMPDP

The relationship between infrared light （IR） and vacuum ultraviolet （VUV） emission in shadow mask plasma display panels （SMPDP） at high xenon content and high voltage is investigated. The respective ratios of VIS/IR-823 am, VIS/IR-828 nm and of efficacy/VIS/IR-823 nm, efficacy/VIS/IR-823 nm are calculated to determine the behavior of the xenon excitation efficiency and the electron excitation efficiency as a function of the driving voltage and xenon content. It is found that the xenon excitation efficiency is almost independent of the driving voltage, and increases approximately linearly with the xenon content. The values for efficacy/VIS/IR-828 nm increase rapidly with the xenon content, but saturate at a xenon ratio of about 30% while, on the other hand, the efficacy/VIS/IR-823 nm values decrease continuously with the xenon content.

Optimal strategy of searching FPD weights scanning matrix using GA-PSO

This paper discusses a kind of optimal method used for searching flat panel display （FPD） scanning matrix. The method adopts bionic algorithm： genetic algorithm （GA） and particle swarm optimization （PSO） algorithm. The method using single GA is more time-consuming, and the search efficiency is low in later evolution; the PSO algorithm is easily falling into the local optimal solution and appears the premature convergent phenomenon. Hence, a hybrid approach of GAPSO is found to optimize the search for high grayscale weights scanning matrix. Finally in the acceptable time, it finds a weight scanning matrix （WSM） of 256 gray scales with Matlab, whose scanning efficiency reaches 94.73% and the linearity is very good.

Effect of Wall Charge on Striation in Plasma Display Cells

Different configurations and driving voltages have been employed to investigate the effect of the wall charge on the striations in macroscopic plasma display panel （PDP） cells. The experimental results show that a discharge channel near the dielectric layer is indispensable to striation occurring in the anode area during a discharge, while the pre-accumulated charge on the dielectric layer and the surface state are not important. The origin of the striation is related only to the physical process in the cell. The dielectric layer acts as a charge collector during a PDP discharge.

FLICKER INDEX METHOD FOR EVALUATING FLICKER IN COLOR PDPs

Objective In order to red uc e the flicker in color plasma display panel (PDP), the highly peaked light outpu t at certain positions and the strong luminance difference among subfields, whic h cause flicker in PDP, is analyzed; and a flicker index method is developed to evaluate flicker in PDP based on the flicker theory and the electroencephalograp h response model for luminance. Methods This method considers f licker as a main result of the fundamental frequency component of luminance supe rimposed on the DC-component, the flicker index is defined as ratio between the positive square roots of the sum of the two square components. Results & Conclusion The calculation results of flicker index indicate that flicker can be obviously weakened via increase of subfield number, symmetrical s election and homogeneous interlaced distribution of major weight subfields . Fli cker can be further reduced by choosing the suitable subfield order according to gray scale region of image.

A New Method for Measuring the Wall Charge Waveforms of AC PDP

A new method is developed to measure the wall charge waveforms in coplanar alternating current plasma display panel (AC PDP). In the method, two groups of display electrodes are selected from a coplanar AC PDP and two capacitors are respectively connected with these two groups of display electrodes in series, and a measuring circuit and a reference circuit are thus constructed. With the help of special processing, discharge takes place in the cells included in the measuring circuit under a normal drive voltage but no discharge takes place in the cells included in the reference circuit under a normal drive voltage. The wall charge waveforms are obtained from the voltage difference between the two capacitors. Using the method, the wall charge waveforms are measured during resetting period, addressing period and sustaining period for the 304.8mm (12-inch) test PDP panel. The result shows that the wall voltage is about 96V during the sustaining period.