A low-noise X-band microwave source with digital automatic frequency control for electron paramagnetic resonance spectroscopy

We report a new design of microwave source for X-band electron paramagnetic resonance spectrometer.The microwave source is equipped with a digital automatic frequency control circuit.The parameters of the digital automatic frequency control circuit can be flexibly configured for different experimental conditions,such as the input powers or the quality factors of the resonator.The configurability makes the microwave source universally compatible and greatly extends its application.To demonstrate the ability of adapting to various experimental conditions,the microwave source is tested by varying the input powers and the quality factors of the resonator.A satisfactory phase noise as low as-135 d Bc/Hz at 100-k Hz offset from the center frequency is achieved,due to the use of a phase-locked dielectric resonator oscillator and a direct digital synthesizer.Continuous-wave electron paramagnetic resonance experiments are conducted to examine the performance of the microwave source.The outstanding performance shows a prospect of wide applications of the microwave source in numerous fields of science.

Electron paramagnetic resonance study of amphiphiles partitioning behavior in desiccation-tolerant moss during dehydration

Desiccation tolerance is a crucial characteristic for desert moss surviving in arid regions. Desiccation procedure always induces amphiphiles transferring from the polar cytoplasm into lipid bodies. The behavior of amphiphiles transferring can contribute to the enhancement of desiccation tolerance and the reduction of plasma membrane integrity simultaneously. The effects of amphiphiles partitioning into the lipid phase during water loss has been studied for pollen and seeds using electron paramagnetic resonance （EPR） spectroscopy. However, desiccation-tolerant high plants occur among mosses, several angiosperms and higher plants seeds or pollens. They have different strategies for survival in dehydration and rehydration. A desiccation-tolerant moss Tortula desertorurn was used to investigate the behaviors of amphiphilic molecules during drying by spin label technology. There are small amount of amphiphilic probes partitioning into membrane during moss leaves dehydration, comparing with that in higher plants. Cytoplasm viscosity changed from 1.14 into glass state only dehydration less than 60 min. Moss leaves lost plasma membrane integrity slightly,from 0.115 to 0.237, occurred simultaneously with amphiphiles partition. The results showed the more advantages of mosses than higher plants in adapting fast dehydration. We propose that EPR spin label is feasible for studying the amphiphiles partitioning mechanisms in membrane protection and damage for desiccation-tolerant mosses.

Temperature-Dependent Formation of Redox Sites in Molybdenum Trioxide Studied by Electron Paramagnetic Resonance Spectroscopy

The formation and qualification of redox sites in transition metal oxides are always the active fields related to electronics, catalysis, sensors, and energy-storage units. In the present study, the temperature dependence of thermal reduction of MoO3 was surveyed at the range of 350℃ to 750℃. Upon reduction, the formed redox species characterized by EPR spectroscopy are the MoVion and superoxide anion radical (O2-) when the reduction was induced at the optimal temperature of 300-350℃. When heating-up from 350℃, the EPR signals started to decline in amplitude. The signals in the range of 400-450℃ decreased to half of that at 350℃, and then to zero at ~600℃. Further treatment at even higher temperature or prolonged heating time at 500℃ caused more reduction and more free electrons were released to the MoO3 bulk, which results in a delocalized means similar to the antiferromagnetic coupling. These data herein are helpful to prepare and study the metal-oxide catalysts.

Identification of Superoxide O2^- during KNO3-NaNO2-NaNO3 Salt by Electron UV-Vis Absorption Spectroscopy Thermal Decomposition of Molten Paramagnetic Resonance and

On account of excellent thermal physical properties, molten nitrates/nitrites salt has been widely employed in heat transfer and thermal storage industry, especially in concentrated solar power system. The thermal stability study of molten nitrate/nitrite salt is of great importance for this system, and the decomposition mechanism is the most complicated part of it. The oxide species O2^2- and O2^- were considered as intermediates in molten KNO3-NaNO3 while hard to been detected in high temperature molten salt due to their trace concentration and low stability. In this work, the homemade in situ high temperature UV- Vis instrument and a commercial electron paramagnetic resonance were utilized to supply evidence for the formation of superoxide during a slow decomposition process of heat transfer salt （HTS, 53 wt% KNO3/40 wt% NaNO2/7 wt% NaNO3）. It is found that the superoxide is more easily generated from molten NaNO2 compared to NaNO3, and it has an absorption band at 420-440 nm in HTS which red shifts as temperature increases. The band is assigned to charge-transfer transition in NaO2 or KO2, responsible for the yellow color of the molten nitrate/nitrite salt. Furthermore, the UV absorption bands of molten NaNO2 and NANO3 are also obtained and compared with that of HTS.

Immobilization of penicillin G acylase on paramagnetic polymer microspheres with epoxy groups

Paramagnetic polymer microspheres were synthesized by the inverse suspension polymerizationmethod through polymerization of glycidyl methacrylate,ally glycidyl ether and methacrylamide onthe surface of silica‐coated Fe3O4nanoparticles using N,N’‐methylene‐bis(acrylamide)as across‐linking agent.Penicillin G acylase(PGA)was covalently immobilized on the surface of theparamagnetic microspheres by reacting the amino groups of the PGA molecules with the epoxygroups of the paramagnetic polymer microspheres.The effect of the SiO2coating and the amount ofparamagnetic Fe3O4nanoparticles on the initial activity and the operational stability of the immobilizedPGA was investigated.The results indicated that SiO2played an important role in the polymerization process and paramagnetic polymer microspheres with a SiO2‐coated Fe3O4nanoparticles mass content of7.5%are an optimal support material for PGA immobilization.Immobilized PGA on the paramagnetic polymer microspheres shows a high initial activity of430U/g(wet)and retains99%of its initial activity after recycling10times.Furthermore,immobilized PGA exhibits high thermal stability,pH stability and excellent reusability,which can be rapidly recycled by the aid of magnet.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.

Electron paramagnetic resonance characterization of aluminum ion implantation-induced defects in 4H-SiC

Deep-level defects in silicon carbide(SiC)are critical to the control of the performance of SiC electron devices.In this paper,deep-level defects in aluminumion-implanted 4H-SiC after high-temperature annealingwere studied using electron paramagnetic resonance(EPR)spectroscopy at temperatures of 77 K and 123 K under different illumination conditions.Results showed that the main defect in aluminum ion-implanted 4H-SiC was the positively charged carbon vacancy(VC+),and the higher the doping concentration was,the higher was the concentration of VC+.Itwas found that the type of material defectwas independent of the doping concentration,although more VC+defects were detected during photoexcitation and at lower temperatures.These results should be helpful in the fundamental research of p-type 4H-SiC fabrication in accordance with functional device development.

Paramagnetic Anisotropy of CdGd_2(WO_4)_(4-δ) Single Crystal

CdGd2 （WO4）4 -δ single crystal was grown using the Czochralski＇s method. The crystal structure was tetragonal seheelite with lattice parameters a = b = 0.5203 nm and c = 1. 1359 nm. There were vacancies of （WO4）^2- , therefore, there were some Gd^2＋ ions. Langevin paramagnetism and anisotropy were observed from the δ-T curves at room temperature. The susceptibility X//was 3.5018×10^-3, and X⊥ was 3.4403× 10^-2. The anisotropy was also observed in the electron spin resonance （ESR） experiments. The anisotropic Land6 factors were g//= 2. 1333 and g~ = 2. 8411. The direction of easy magnetization was in the α-b plane. Anisotropic paramagnetic Curie constants C//and C⊥ were not only related to macroscopic a that was observed through the experiment, but were also related to J⊥ and J//, which were the microscopic quantum numbers of the Gd^2＋ and Gd^3｜ ions. Based on the detailed analyses, the proportion of 36.8% of Gd^3＋ ions to 63.2% of Gd^2＋ ions in the Gd ions of the CdGd2（WO4）4-δ crystal was calculated, and δ was 0.638 in the single crystal.

X-Ray Diffraction, Electron Paramagnetic Resonance and Optical Absorption Study of Bauxite

The bauxite mineral obtained from Araku, Vishakapatnam district of Andhra Pradesh, India is used in the present work. Structural characterization was performed by X-ray diffraction (XRD). The mineral was found to be gibbsite in phase. The transitional metal ions present were investigated using electron paramagnetic resonance (EPR) and optical absorption spectra. The EPR results suggest that Fe3+ has replaced Al3+ in the unit cell of bauxite. The optical absorption spectrum is due to Fe3+ which indicates that it is in distorted octahedral environment. The near-infrared (NIR) spectrum is due to water fundamentals and combination overtones, which confirm the formula of the compound. The impurities in the mineral are identified using spectroscopic techniques.

Electron paramagnetic resonance studies of the chelate-based ionic liquid in different solvents

The electron paramagnetic resonance spectra of the chelate-based ionic liquid[C_(10)mim][Cu(F_6-acac)_3]in different solvents have been obtained at 120 K.It was found that the values of the^(63)Cu hyperfine coupling constants(A_(IL))of[C_(10)mim][Cu(F_6-acac)_3]in molecular solvents were from 116 to 180 Gauss.Moreover,the A_(IL)values in general ionic liquids are more complicated,and two sets of peaks can often be observed in their electron paramagnetic resonance spectra.Based on the Kamlet-Taft parameters,relative permittivity,the experimental results were discussed in terms of solvation effect and coordination of the solvents.

Focused-Ion-Beam Induced Paramagnetic Defects in FAMn:PbI3 Perovskite Films

FAMn:PbI3 perovskite films were synthesized and probed mainly through electron spin resonance (ESR) spectroscopy. FAMn:PbI3 with low (~1%) Mn concentration showed a hyperfine sextet line originated from Mn++ ions. FAMn:PbI3 with high (10%) Mn concentration showed broad resonance (~500 G peak-to-peak linewidth). However, after bombardment of FAMn:PbI3 with high Mn concentration by focused ion beams (FIB), a sharp ESR peak appeared. The peak-to-peak linewidth (ΔHpp) was ~8 G regardless of the temperature. The FIB-induced defect showed Curie behavior at low temperatures (5 K - 50 K), which indicates the presence of localized electrons at the defect sites at low temperatures. The g-value increased from g = 2.0002 to 2.0016 as the temperature increased from 5 K to 50 K. Together with the ongoing search for electron spin echo (ESE), this could potentially provide a platform for realizing magnetic bits, information storage, and increased manipulation speed.

Electron Paramagnetic Resonance and Optical Absorption Studies on Copper Ions in Mixed Alkali Cadmium Phosphate Glasses

Electron paramagnetic resonance （EPR） and optical absorption studies were carried out at room temperature on copper doped mixed alkali cadmium phosphate （LiNaCdP） glasses to understand the nature and symmetry of dopant. Three samples with varying concentrations of alkali ions have been prepared. The spin Harniltonian parameters obtained from room temperature EPR spectra are： gli=2.437, 9⊥=2.096, A‖=117×10-4 cm-1, A⊥=26×10-4 cm-1 for LiNaCdP1, g‖=2.441, g⊥=2.088, A‖=121×10-4 cm-1, A⊥=25×10-4 cm-1 for LiNaCdP2and g‖=2.433,g⊥=2.096, A‖=125×10 4cm-1, A⊥=32×10-4cm-1 for LiNaCdP3. TheseEPR results indicate that the dopant Cu2＋ ion enters the glass matrix into a tetragonally elongated octahedral site. The bonding parameters evaluated by correlating optical and EPR data suggest that bonding between the central metal ion and ligands is partially covalent. The mixed alkali effect in cadmium phosphate glasses was reported.

Effect of local structure on electron paramagnetic resonance spectra for trigonal [Cr(H_2O)_6]^(3+) coordination complex in the sulfate alums series:a ligand field theory study

A simple theoretical method is introduced for studying the interrelation between electronic and molecular structures.By diagonalizing the 120 × 120 complete energy matrices,the relationships between zero-field splitting （ZFS） parameter D and local distortion parameter △θ for Cr^3＋ ions doped,separately,in α- and β- alums are investigated.Our results indicate that there exists an approximately linear relationship between D and △θ in a temperature range 4.2-297 K and the signs of D and △θ are opposite to each other.Moreover,in order to understand the contribution of spin-orbit coupling coefficient ζ to ZFS parameter D,the relation between D and ζ is also discussed.

PARAMAGNETIC MEISSNER EFFECTS IN MELT-TEXTURED Y_(0.99)Nd_(0.01)Ba_2Cu_3O_(7-y)SUPERCONDUCTOR

The paramagnetic Meissner effect (PME) was observed on the field-cooled M-T curves of melt-textured Y0.99Nd0.01Ba2Cu3O7-y in applied magnetic fields from 1kOe to 40kOe. In the magnetic field below 1kOe, the sample undergoes the typical transition from the normal state to the superconducting state when it was cooled down. The applied magnetic fields in which the PME occurs, are very high compared with the fields reported in literatures. We propose that the occurrence of the PME may be due to a phase transition of flux vortices in the superconductors.

Applications of Natural Radiation-Induced Paramagnetic Defects in Quartz to Exploration in Sedimentary Basins

Quartz grains in contact with uranium-bearing minerals or fluids are characterized by natural radiation-induced paramagnetic defects （e. g. , oxygen vacancy centers, silicon vacancy centers, and peroxy radicals）, which are amenable to study by electron paramagnetic resonance （EPR） spectroscopy. These natural radiation-induced paramagnetic defects, except for the oxygen vacancy centers, in quartz are concentrated in narrow bands penetrated by α particles： （1） in halos around U- and Th-bearing mineral inclusions and （2） in outer rims or along fractures. The second type of occurrence provides information about uranium mineralization or remobilization （i. e. , sources of uranium, timing of mineralization or remobilization, pathways of uranium-bearing fluids）. It can also be used to evaluate sedimentary basins for potential of uranium mineralization. In particular, the peroxy radicals are stable up to 800℃ and, therefore, are useful for evaluating metasedimentary rocks （e. g. , Paleoproterozoic metasedimentary sequences in the central zone of the North China craton）. EPR study of the Changcheng Series can focus on quartz from the sediment-basement unconformity and faults to determine the presence and types of natural radiation-induced paramagnetic defects, with which to identify and prioritize uranium anomalies. Other potential applications of natural radiation-induced paramagnetic defects in quartz include uranium-bearing hydrocarbon deposits in sedimentary basins. For example, the Junggar, Ordos, and Tarim basins in northwestern China all contain important oil and natural gas fields and are well known for elevated uranium concentrations, including economic sandstone-hosted uranium deposits. Therefore, systematic studies on the distribution of natural radiation-induced paramagnetic defects in quartz from host sedimentary sequences are expected to provide information about the migration of oil and natural gas in those basins.

Monitoring the autoproteolysis of hiv-1 protease by site-directed spin-labeling and electron paramagnetic resonance spectroscopy

Site-directed spin-labeling with continuous wave electron paramagnetic resonance spectroscopy was used to monitor autoproteolysis of HIV-1 protease, an enzyme essential for viral maturation. Two protein constructs were examined, namely subtype F and the circulating recombinant form CRF01_A/E. As the protease undergoes self-cleavage, protein unfolds and small peptide fragments containing the spin label are generated, which collectively give rise to a sharp spectral component that is easily discernable in the high-field resonance line in the EPR spectrum. By monitoring the intensity of this spectral component over time, the autoproteolytic stability of each construct was characterized under various conditions. Data were collected for samples stored at 4 °C, 25 °C, and 37 °C, and on a subtype F HIV-1 protease sample stored at 25 °C and containing the FDA-approved protease inhibitor Tipranavir. As expected, the rate of autoproteolysis decreased as the storage temperature was lowered. Minimal autoproteolysis was seen for the sample that contained Tipranavir, providing direction for future spectroscopic studies of active protease samples. When compared to standard methods of monitoring protein degradation such as gel electrophoresis or chromatographic analyses, spin-labeling with CW EPR offers a facile, real-time, non-consuming way to monitor autoproteolysis or protein degradation. Additionally, mass spectrometry studies revealed that the N-termini of both constructs are sensitive to degradation and that the sites of specific autoproteolysis vary.

Theoretical Studies of Electron Paramagnetic Resonance Parameters for Cr^4＋ Ions in Ca2GeO4 Crystals

The electron paramagnetic resonance (EPR) parameters (zero-Geld splitting Dand g factors g_‖, g_⊥) of Cr~(4+) ions in Ca_2 GeO_4 crystals have been calculated from thecomplete high-order perturbation formulas of EPR parameters for a 3d~2 ion in trigonal MX_4clusters. In these formulas, in addition to the contributions to EPR parameters from the widely usedcrystal-field (CF) mechanism, the contributions from the charge-transfer (CT) mechanism (which areoften neglected) are included. From the calculations, it is found that for the high valence state3d~n ions in crystals, the reasonable explanation of EPR parameters (in particular, the g factors)should take both the CF and CT mechanisms into account.

Synthesis and Characterization of Surface-modified Fe_3O_4 Super-paramagnetic Nanoparticles

Aqueous dispersion and stability of Fe304 nanoparticles remain an issue unresolved since aggregation of naked iron nanoparticles in water. In this study, we successfully synthesized different Fe304 super-paramagnetic nanoparticles which were modified by three kinds of materials [DSPE-MPEG2000, TiO2 and poly acrylic acid （PAA）] and further detected their characteristics. Trans- mission electron microscopy （TEM） clearly showed sizes and morphology of the four kinds of nanopar- ticles. X-ray diffraction （XRD） proved successfully coating of the three kinds of nanoparticles and their structures were maintained. Vibrating sample magnetometer （VSM） verified that their magnetic proper- ties fitted for the super-paramagnetic function. More importantly, the particle size analysis indicated that Fe304@PAA had a better size distribution, biocompatibility, stability and dispersion than the other two kinds of nanoparticles. In addition, using CNE2 cells as a model, we found that all nanoparticles were nontoxic. Taken together, our data suggest that Fe304@PAA nanoaparticles are superior in the applica- tion of biomedical field among the four kinds ofFe304 nanoparticles in the future.

电子顺磁共振技术在化工基础研究中的应用进展

电子顺磁共振(electron paramagnetic resonance,EPR)技术能够检测自由基、过渡金属离子及缺陷等顺磁性物质,谱图具有高特异性,背景信号少,既可以检测溶液样品,也可以检测固态样品,且检测限低。在化工基础研究中,尤其是自由基相关过程研究中,EPR技术的优势是其他谱学无可比拟的。但是化工领域的科学家们使用EPR技术并不广泛。综述了EPR在化工基础相关研究中应用的一些例子,包括催化材料的表征、活性中间体的表征、溶剂性质表征及材料性能表征四个方面,希望能让更多化工领域工作者了解EPR技术,并使用EPR技术解决化工问题。

Fe_(3)O_(4)基核壳纳米结构材料的制备及顺磁性研究

以Fe_(3)O_(4)为磁核,SiO_(2)为外壳,制备了Fe_(3)O_(4)@SiO_(2)核壳纳米结构材料,使用三乙氧基硅烷对Fe_(3)O_(4)@SiO_(2)进行表面亲水改性,研究了亲水改性对Fe_(3)O_(4)@SiO_(2)顺磁性能和催化性能的影响。结果表明:立方相结构的Fe_(3)O_(4)是核壳材料中主要的晶体相,表面的SiO_(2)为非晶态,表面亲水处理后未改变Fe_(3)O_(4)@SiO_(2)的晶格结构,Fe_(3)O_(4)@SiO_(2)为80~110 nm的不规则颗粒状,SiO_(2)包覆在Fe_(3)O_(4)外部,亲水处理后改善了颗粒的分布均匀性。亲水处理的Fe_(3)O_(4)@SiO_(2)的饱和磁化强度降低至20.31 emu/g,具有超顺磁性。以含Cd^(2+)的金属废水为吸附降解对象,表面亲水处理后的Fe_(3)O_(4)@SiO_(2)去除率提高至94.2%,二级动力学模型更适合于Fe_(3)O_(4)@SiO_(2)对Cd^(2+)的吸附,模型的相关系数为0.9943,拟合效果更好,表明了Fe_(3)O_(4)@SiO_(2)对Cd^(2+)的吸附速率受化学吸附的影响较大。