Mathematical Model for Tempering Time Effect on Quenched Steel Based on Hollomon Parameter

Through the differentiating and integrating process, a mathematical model for tempering time effect on quenched steel was derived based on the attribute of state function and the general equation of Hollomon parameter, which correlates the tempering hardness with the tempering time at different tempering temperature. Using the established model, the linear relationship between the tempering hardness and the tempering time in logarithm was proved theoretically, and the tempering hardness for various tempering time was reduced to the measurement and calculation of a hardness experiment tempered for 1 h at different tempering temperatures. Moreover, the hardness of steel 42CrMo and T8Mn tempered for various times at 200-600℃ was calculated using this method. The predicted results are in good agreement with those of the available experiments.

Fermi Energy-Incorporated Generalized BCS Equations for the Temperature-Dependent Critical Current Density and the Related Parameters of a Superconductor for All <i>T</i>≤ <i>Tc</i>and Their Application to Aluminium Strips

Presented here are the Generalized BCS Equations incorporating Fermi Energy for the study of the {Δ, Tc, jc(T)} values of both elemental and composite superconductors (SCs) for all T ≤ Tc, where Δ, Tc and jc(T) denote, respectively, one of the gap values, the critical temperature and the T-dependent critical current density. This framework, which extends our earlier study that dealt with the {Δ0, Tc, jc(0)} values of an SC, is also shown to lead to T-dependent values of several other related parameters such as the effective mass of electrons, their number density, critical velocity, Fermi velocity (VF), coherence length and the London penetration depth. The extended framework is applied to the jc(T) data reported by Romijn et al. for superconducting Aluminium strips and is shown not only to provide an alternative to the explanation given by them, but also to some novel features such as the role of the Sommerfeld coefficient γ(T) in the context of jc(T) and the role of VF(T) in the context of a recent finding by Plumb et al. about the superconductivity of Bi-2212.

2021年老挝M_(S)6.0地震序列研究

云南地震活动与周边强震存在“构造相连,动力同源”的特征,研究周边强震的序列演化特征及发震构造,对云南地区地震研究具有重要意义。2021年12月24日老挝M_(S)6.0地震发生在滇西南地区的NW向整董断裂附近,震源机制解显示,此次地震是一次走滑型破裂事件,破裂方向与区域构造特征一致。老挝M_(S)6.0地震序列属于前震-主震-余震型序列,主震前震中附近出现3~4级地震非常活跃的现象,前震序列参数计算显示b值波动相对幅度较大,h值出现“上翘”形态,而余震序列b值和h值变化均相对平稳,主震的同震库伦应力结果表明老挝地震可能对云南地区有应力加载作用。

Dynamics and adaptive control of a dual-arm space robot with closed-loop constraints and uncertain inertial parameters

A dynamics-based adaptive control approach is proposed for a planar dual-arm space robot in the presence of closed-loop constraints and uncertain inertial parameters of the payload. The controller is capable of controlling the po- sition and attitude of both the satellite base and the payload grasped by the manipulator end effectors. The equations of motion in reduced-order form for the constrained system are derived by incorporating the constraint equations in terms of accelerations into Kane＇s equations of the unconstrained system. Model analysis shows that the resulting equations perfectly meet the requirement of adaptive controller design. Consequently, by using an indirect approach, an adaptive control scheme is proposed to accomplish position/attitude trajectory tracking control with the uncertain parameters be- ing estimated on-line. The actuator redundancy due to the closed-loop constraints is utilized to minimize a weighted norm of the joint torques. Global asymptotic stability is proven by using Lyapunov＇s method, and simulation results are also presented to demonstrate the effectiveness of the proposed approach.

Soil Parameter Identification for Wheel-terrain Interaction Dynamics and Traversability Prediction

This paper presents a novel technique for identifying soil parameters for a wheeled vehicle traversing unknown terrain. The identified soil parameters are required for predicting vehicle drawbar pull and wheel drive torque, which in turn can be used for traversability prediction, traction control, and performance optimization of a wheeled vehicle on unknown terrain. The proposed technique is based on the Newton Raphson method. An approximated form of a wheel-soil interaction model based on Composite Simpson＇s Rule is employed for this purpose. The key soil parameters to be identified are internal friction angle, shear deformation modulus, and lumped pressure-sinkage coefficient. The fourth parameter, cohesion, is not too relevant to vehicle drawbar pull, and is assigned an average value during the identification process. Identified parameters are compared with known values, and shown to be in agreement. The identification method is relatively fast and robust. The identified soil parameters can effectively be used to predict drawbar pull and wheel drive torque with good accuracy. The use of identified soil parameters to design a traversability criterion for wheeled vehicles traversing unknown terrain is presented.

Investigation of ductile iron casting process parameters using Taguchi approach and response surface methodology

To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different casting parameters such as pouring temperature, inoculation, carbon equivalent, moisture content, green compression strength, permeability and mould hardness were selected. Three different melts of metal with 0.4wt.%, 0.6wt.%, and 0.8wt.% inoculation （Fe-Si-Mg alloy and post inoculant） were produced using a 1-ton capacity coreless medium frequency induction furnace. L-27 orthogonal array with 3-level settings were chosen for the analysis. Responses for each run were observed. The signal-to-noise （S/N） ratio for each run was calculated using the Taguchi approach, and the optimized levels of different casting parameters were identified based on the SIN ratio. The analysis of variance for the casting acceptance percentage concludes that inoculation is the most significant factor affecting the castings＇ quality with a contribution percentage of 44%; an increase in inoculation results in a significant improvement in acceptance percentage of ductile iron castings. The experiment results showed that with the optimized parameters, the rejection rate was reduced from 16.98% to 6.07%.

S Phase Cell Percentage Normalized BrdU Incorporation Rate, a New Parameter for Determining S Arrest

In this study, a new parameter, S phase cell percentage （S fraction） normalized BrdU （SFN-BrdU） incorporation rate, was introduced to detect $ arrest. The results showed a positive linear correlation between the BrdU incorporation rate and the S fraction in unperturbed 16HBE cells. Theoretical analysis indicated that only S arrest could result in a decrease in the SFN-BrdU incorporation rate. Additionally, the decrease in SFN-BrdU incorporation rate and the activation of DNA damage checkpoints further demonstrated that S arrest was induced by diethyl sulfate treatment of 16HBE cells. In conclusion, $FN-BrdU incorporation rate can be used to detecting S arrest.

Stability Analysis of T-S Fuzzy Control Systems Based on Parameter-dependent Lyapunov Function

For discrete-time T-S fuzzy systems, the stability and controller design method are in-vestigated based on parameter-dependent Lyapunov function (PDLF). T-S fuzzy systems di?er fromnon-fuzzy systems with polytopic description or multi-model description in that the weighting coef-ficients have respective meanings. They, however, have stability aspect in common. By adopting astability condition for polytopic systems obtained via PDLF, and combining the properties of T-Sfuzzy systems, new results are given in this paper. An example shows that by applying the newresults, the stability conditions that can be distinguished are less conservative.

Effect of Process Parameters on S-Parameter of Fabric-Based Embroidered Transmission Line

This paper presented a method of fabricating radio frequency( RF) transmission lines by embroidering conductive thread on fabric. A digital embroidery machine was selected to fabricate transmission lines. Effects of the typical process parameters on the S-parameter of these RF transmission lines were tested and discussed. And the results showed that embroidery process parameters such as stitch direction,stitch spacing,stitch length and embroidered tension had significant effects on the RF performance of embroidered transmission lines,of which stitch type was the most important factor for the measured S-parameter of transmission lines.

DATA MODELING METHOD BASED ON PARTIAL LEAST SQUARE REGRESSION AND APPLICATIO N IN CORRELATION ANALYSIS OF THE STATOR BARS CONDITION PARAMETERS

Objective To investigate v arious data message of the stator bars condition parameters under the condition that only a few samples are available, especially about correlation information between the nondestructive parameters and residual breakdown voltage of the stat or bars. Methods Artificial stator bars is designed to simulat e the generator bars. The partial didcharge( PD) and dielectric loss experiments are performed in order to obtain the nondestructive parameters, and the residua l breakdown voltage acquired by AC damage experiment. In order to eliminate the dimension effect on measurement data, raw data is preprocessed by centered-compr ess. Based on the idea of extracting principal components, a partial least squar e (PLS) method is applied to screen and synthesize correlation information betwe en the nondestructive parameters and residual breakdown voltage easily. Moreover , various data message about condition parameters are also discussed. Re sults Graphical analysis function of PLS is easily to understand vario us data message of the stator bars condition parameters. The analysis Results ar e consistent with result of aging testing. Conclusion The meth od can select and extract PLS components of condition parameters from sample dat a, and the problems of less samples and multicollinearity are solved effectively in regression analysis.

Research on COB De-embedding in Scattering Parameter Measurement

The popular radio frequency(RF) chip on board(COB) test has gradually taken the place of onwafer test due to the high efficiency and high power. This paper presents the extended Open-Short-Load(OSL) that is one-port calibration method to verify the error model de-embedding in S parameter measurement. Threelevel cascade structure on COB's system error model is proposed and analyzed. Four kinds of calibration plane solutions for de-embedding are verified. At last,on-board calibration(CAL) kits solution is established to decrease the system error to the least value. The maximum error shift can be controlled less than 0.1 dB comparing with the on-wafer test results. In general,the practical application results prove that this method is reasonable and effective and easy to be mastered.

A method to determine relevant geomechanical parameters for evaluating the hydraulic erodibility of rock

Among the methods used for evaluating the potential hydraulic erodibility of rock,the most common methods are those based on the correlation between the force of flowing water and the capacity of a rock to resist erosion,such as Annandale’s and Pells’methods.The capacity of a rock to resist erosion is evaluated based on erodibility indices that are determined from specific geomechanical parameters of a rock mass.These indices include unconfined compressive strength(UCS)of rock,rock block size,joint shear strength,a block’s shape and orientation relative to the direction of flow,joint openings,and the nature of the surface to be potentially eroded.However,it is difficult to determine the relevant geomechanical parameters for evaluating the hydraulic erodibility of rock.The assessment of eroded unlined spillways of dams has shown that the capacity of a rock to resist erosion is not accurately evaluated.Using more than 100 case studies,we develop a method to determine the relevant geomechanical parameters for evaluating the hydraulic erodibility of rock in unlined spillways.The UCS of rock is found not to be a relevant parameter for evaluating the hydraulic erodibility of rock.On the other hand,we find that the use of three-dimensional(3D)block volume measurements,instead of the block size factor used in Annandale’s method,improves the rock block size estimation.Furthermore,the parameter representing the effect of a rock block’s shape and orientation relative to the direction of flow,as considered in Pells’method,is more accurate than the parameter adopted by Annandale’s method.

Effects of thermodynamics parameters on mass transfer of volatile pollutants at air-water interface

A transient three-dimensional coupling model based on the compressible volume of fluid （VOF） method was developed to simulate the transport of volatile pollutants at the air-water interface. VOF is a numerical technique for locating and tracking the free surface of water flow. The relationships between Henry＇s constant, thermodynamics parameters, and the enlarged topological index were proposed for nonstandard conditions. A series of experiments and numerical simulations were performed to study the transport of benzene and carbinol. The simulation results agreed with the experimental results. Temperature had no effect on mass transfer of pollutants with low transfer free energy and high Henry＇s constant. The temporal and spatial distribution of pollutants with high transfer free energy and low Henry＇s constant was affected by temperature. The total enthalpy and total transfer free energy increased significantly with temperature, with significant fluctuations at low temperatures. The total enthalpy and total transfer free energy increased steadily without fluctuation at high temperatures.

Evaluation of the Physicochemical Parameters of Cow’s Fresh Milk in Shkodra

Milk is universally recognized as complete food, which contains essential components for human nutrition. Physicochemical analysis constitutes an important device that monitors its quality. The purpose of this study was to determine the physicochemical characteristics of fresh cow milk in samples taken in the region of Shkodra and Lezha and compare it to European quality standards. Results of the analyses were statistically processed by the Minitab 17 statistical program. Results showed that there is no significant difference (P > 0.05) in fat, protein, lactose and density value, while there is significant difference (P < 0.05) in pH, ash% without fat, freezing point and water value. The results show a stability of physicochemical parameters of milk, with variation according to the region where samples were gathered.

Real-time parameters monitoring system for underground equipment based on panoramic images

Complex terrain and working equipment in coal mine underground need a way to ensure coal mine safety. In this paper, the way to monitor the real-time status of underground equipment was put forward, and it was proved to be effective as commanding and dispatching system. Monitoring system for underground equipment based on panoramic images was effectively combined with real-time sensor data and static panoramic images of underground surrounding, which not only realizes real-time status monitoring for underground equipment, but also gets a direct scene for underground surrounding. B/S mode was applied in the monitoring system and this is convenient for users to monitor the equipment. Meantime, it can reduce the waste of the data resource.

EFFECT OF OPENING OPERATING PARAMETERS ON YARN QUALITY IN FINE AND MEDIUM COUNT FRICTION SPINNING

In this paper, a quantitative analysis of the opening quality in friction spinning and its main ef-fecting factors is first made. Upon this basis the Box-Hunter’s experimental design method is usedto establish the quadratic regressional equations in terms of primary opening technologicalparameters and yarn quality for medium and fine count friction spinning. The results of analysisand discussion show that the proper choice of opening roller speed and its reasonable match withthe yarn count is singificant for ensuring the spinning quality index as well as reducing unevenness,thin and thick places of the yarn.

<i>Moringa oleifera</i>Diets Effect on Haematological Parameters of Rat (<i>Ratus norvegicus</i>)

With aim of place at the disposal of the laboratories nonconventional food with food values and which do not have impact on the system haematopoietic of the rats of laboratory in particular the rat of the species Rattus norvegicus, the study of the haematologic parameters of rats nourished with nonconventional food makes containing powder of Moringa oleifera was undertaken. Indeed, analysis of the blood taking away carried out following the administration of five diets container various rates of powder of Moringa oleifera (0% (Control food), 25%, 50%, 75% and 100%) respectively codified L3P, L3P25, L3P50, L3P75 and L3P100. These different food formulations were administered to rats (Ratus norvegicus) during three months. The weight of these animals was daily taken, followed by blood samples every 30 days for the determination of the blood count. The results of the study were shown differences between the various food formulations for each period of blood samples in biological parameters. These differences were more significant for platelets. During the three months of study, the hematocrit, platelets, MCV and outside the control group, were reported a slight progressive increase. The leukocyte parameters of all the rats in the investigation, indicated an increase in the second month. In conclusion, the study shows that during the three months of investigation, the tested foods do not disturb the haematological parameters except for thrombocytes which reveal a modification.

Analysis on a Set of 12-parameter Rectangular Plate Element with High Accuracy

It is proved that the so-called a set of 12-parameter rectangular plate elements with high accuracy constructed by using double set parameter method and undetermined method are, in fact, the same one; the real shape function space is nothing but the Adini＇s element＇s, which has nothing to do with the other high degree terms and leads to a new method for constructing the high accuracy plate elements. This fact has never been seen for other conventional and unconventional, conforming and nonconforming rectangular plate elements, such as Quasi-conforming elements, generalized conforming elements and other double set parameter finite elements. Moreover, such kind of rectangular elements can not be constructed by the conventional finite element methods.

Polarizabilities and Orientational Order Parameter in N-(p-n-Ethoxybenzylidene)- p-n-Alkoxy Anilines, 2O.Om LC Compounds

n.m, n.Om, nO.m and nO.Om compounds play an important role in the fundamental and applied aspects. As a part of our systematic studies of the above homologous series regarding the synthesis, characterization and phase transition studies, here the authors report the polarizabilities and orientational order parameter, S in N-(p-n-ethoxybenzylidene)-p-n-alkoxy anilines, 2O.Om with m = 3 to 10 liquid crystalline compounds except with m = 5 which has been already published. The rest of the compounds exhibit the nematic LC phase except with m = 10 which shows the smectic-C phase along the nematic phase which is originally not detected by Godzwon et al. But the author’s observations with TM and differential scanning calorimeter have shown the existence on SmC phase in addition to nematic phase. Further, SmC is clarified using the histogram technique whose details are given below and are published elsewhere. The orientstonal order parameter, S is estimated using different methods and compared with the value obtained from birefringence, δn = (ne – no) where no field model is used. It is observed in these compounds case as in other LC compounds Vuks isotropic model is favored compared to that of anisotropic model proposed by Neugebauer.

Need for multiple biomarkers to adjust parameters of closed-loop deep brain stimulation for Parkinson's disease

Closed-loop deep brain stimulation（DBS）：DBS has been established as a surgical therapy for movement disorders and select neuropsychiatric disorders.Various efforts to improve the clinical outcomes of the procedure have been previously made.Several factors affect the DBS clinical outcomes such as lead position,programming technique,