Dynamic stability of parametrically-excited linear resonant beams under periodic axial force

The parametric dynamic stability of resonant beams with various parameters under periodic axial force is studied. It is assumed that the theoretical formulations are based on Euler-Bernoulli beam theory. The governing equations of motion are derived by using the Rayleigh-Ritz method and transformed into Mathieu equations, which are formed to determine the stability criterion and stability regions for parametricallyexcited linear resonant beams. An improved stability criterion is obtained using periodic Lyapunov functions. The boundary points on the stable regions are determined by using a small parameter perturbation method. Numerical results and discussion are presented to highlight the effects of beam length, axial force and damped coefficient on the stability criterion and stability regions. While some stability rules are easy to anticipate, we draw some conclusions： with the increase of damped coefficient, stable regions arise; with the decrease of beam length, the conditions of the damped coefficient arise instead. These conclusions can provide a reference for the robust design of parametricallyexcited linear resonant sensors.

Suppression strategy for parametrically excited lateral vibration of mass-loaded string

This paper discusses a simple way to suppress the parametrically excited lateral vibration of a mass-loaded string. Supposing that the mass at the lower end of the string is subjected to a vertical harmonic excitation and neglecting the higher order vibration modes, the equation of motion for the mass-loaded string can be represented by a Mathieus equation with cubic nonlinearity. According to the theory of the Mathieus equation, in the mass-loaded string system, when the vertical vibration frequency of the mass approaches twice the natural frequency of the string lateral vibration, once the vertical vibration amplitude of the mass exceeds a critical value, the parametric resonance will occur in the string. To avoid the parametric resonance, a vibration absorber, composed of a thin beam and two mass blocks attached at both sides of the beam symmetrically, is proposed to install with the mass to reduce its vertical vibration, and ultimately suppress the lateral vibration of the string. Such a suppression strategy is finally validated by experiments.

Nonlinear parametrically excited vibration and active control of gear pair system with time-varying characteristic

In the present work, we investigate the nonlinear parametrically excited vibration and active control of a gear pair system involving backlash, time-varying meshing stiffness and static transmission error. Firstly, a gear pair model is established in a strongly nonlinear form, and its nonlinear vibration characteristics are systematically investigated through different approaches. Several complicated phenomena such as period doubling bifurcation, anti period doubling bifurcation and chaos can be observed under the internal parametric excitation. Then, an active compensation controller is designed to suppress the vibration, including the chaos. Finally, the effectiveness of the proposed controller is verified numerically.

Parametrically excited oscillation of stay cable and its control in cable-stayed bridges＂

This paper presents a nonlinear dynamic model for simulation and analysis of a kind of parametrically excited vibration of stay cable caused by support motion in cable-stayed bridges. The sag, inclination angle of the stay cable are considered in the model, based on which, the oscillation mechanism and dynamic response characteristics of this kind of vibration are analyzed through numerical calculation. It is noted that parametrically excited oscillation of a stay cable with certain sag, inclination angle and initial static tension force may occur in cable-stayed bridges due to deck vibration under the condition that the natural frequency of a cable approaches to about half of the first model frequency of the bridge deck system. A new vibration control system installed on the cable anchorage is proposed as a possible damping system to suppress the cable parametric oscillation. The numerical calculation results showed that with the use of this damping system, the cable oscillation due to the vibration of the deck and/or towers will be considerably reduced.

Classification of parametrically constrained bifurcations

If the constraint boundary relates to a bifurcation parameter, a bifurcation is said to be parametrically constrained. Relying upon some substitution, a parametrically constrained bifurcation is transformed to an unconstrained bifurcation about new variables. A general form of transition sets of the parametrically constrained bifurcation is derived. The result indicates that only the constrained bifurcation set is influenced by parametric constraints, while other transition sets are the same as those of the corresponding nonparametrically constrained bifurcation. Taking parametrically constrained pitchfork bifurcation problems as examples, effects of parametric constraints on bifurcation classification are discussed.

RESPONSE OF PARAMETRICALLY EXCITED DUFFING-VAN DER POL OSCILLATOR WITH DELAYED FEEDBACK

The dynamical behaviour of a parametrically excited Duffing-van der Pol oscillator under linear-plus-nonlinear state feedback control with a time delay is concerned. By means of the method of averaging together with truncation of Taylor expansions, two slow-flow equations on the amplitude and phase of response were derived for the case of principal parametric resonance, it is shown that the stability condition for the trivial solution is only associated with the linear terms in the original systems besides the amplitude and frequency of parametric excitation. And the trivial solution can be stabilized by appreciate choice of gains and time delay in feedback control. Different from the case of the trivial solution, the stability condition for nontrivial solutions is also associated with nonlinear terms besides linear terms in the original system. It is demonstrated that nontrivial steady state responses may lose their stability by saddle-node （SN） or Hopf bifurcation （HB） as parameters vary. The simulations, obtained by numerically integrating the original system, are in good agreement with the analytical results.

BIFURCATION IN A PARAMETRICALLY EXCITED TWO-DEGREE-OF-FREEDOM NONLINEAR OSCILLATING SYSTEM WITH 1∶2 INTERNAL RESONANCE

The nonlinear response of a two_degree_of_freedom nonlinear oscillating system to parametric excitation is examined for the case of 1∶2 internal resonance and, principal parametric resonance with respect to the lower mode. The method of multiple scales is used to derive four first_order autonomous ordinary differential equations for the modulation of the amplitudes and phases. The steady_state solutions of the modulated equations and their stability are investigated. The trivial solutions lose their stability through pitchfork bifurcation giving rise to coupled mode solutions. The Melnikov method is used to study the global bifurcation behavior, the critical parameter is determined at which the dynamical system possesses a Smale horseshoe type of chaos.

ON THE MAXIMAL LYAPUNOV EXPONENT FOR A REAL NOISE PARAMETRICALLY EXCITED CO-DIMENSION TWO BIFURCATION SYSTEM (Ⅱ)

For a co_dimension two bifurcation system on a three_dimensional central manifold, which is parametrically excited by a real noise, a rather general model is obtained by assuming that the real noise is an output of a linear filter system_a zeromean stationary Gaussian diffusion process which satisfies detailed balance condition. By means of the asymptotic analysis approach given by L. Arnold and the expression of the eigenvalue spectrum of Fokker_Planck operator, the asymptotic expansions of invariant measure and maximal Lyapunov exponent for the relevant system are obtained.

ON THE MAXIMAL LYAPUNOV EXPONENT FOR A REAL NOISE PARAMETRICALLY EXCITED CO_DIMENSION TWO BIFURCATION SYSTEM (Ⅰ)

For a real noise parametrically excited co_dimension two bifurcation system on a three_dimensional central manifold, a model of enhanced generality is developed in the present paper by assuming the real noise to be an output of a linear filter system, namely,a zero_mean stationary Gaussian diffusion process that satisfies the detailed balance condition. On such basis, asymptotic expansions of invariant measure and maximal Lyapunov exponent for the relevant system are established by use of Arnold asymptotic analysis approach in parallel with the eigenvalue spectrum of Fokker_Planck operator.

PRESS-based EFOR algorithm for the dynamic parametrical modeling of nonlinear MDOF systems

In response to the identification problem concerning multi-degree of freedom （MDOF） nonlinear systems, this study presents the extended forward orthogonal regression （EFOR） based on predicted residual sums of squares （PRESS） to construct a nonlinear dynamic parametrical model. The proposed parametrical model is based on the non-linear autoregressive with exogenous inputs （NARX） model and aims to explicitly reveal the physical design parameters of the system. The PRESSbased EFOR algorithm is proposed to identify such a model for MDOF systems. By using the algorithm, we built a common-structured model based on the fundamental concept of evaluating its generalization capability through cross-validation. The resulting model aims to prevent over-fitting with poor generalization performance caused by the average error reduction ratio （AERR）-based EFOR algorithm. Then, a functional relationship is established between the coefficients of the terms and the design parameters of the unified model. Moreover, a 5- DOF nonlinear system is taken as a case to illustrate the modeling of the proposed algorithm. Finally, a dynamic parametrical model of a cantilever beam is constructed from experimental data. Results indicate that the dynamic parametrical model of nonlinear systems, which depends on the PRESS-based EFOR, can accurately predict the output response, thus providing a theoretical basis for the optimal design of modeling methods for MDOF nonlinear systems.

Differences between lower extremity joint running kinetics captured by marker-based and markerless systems were speed dependent

Background:The development of computer vision technology has enabled the use of markerless movement tracking for biomechanical analysis.Recent research has reported the feasibility of markerless systems in motion analysis but has yet to fully explore their utility for capturing faster movements,such as running.Applied studies using markerless systems in clinical and sports settings are still lacking.Thus,the present study compared running biomechanics estimated by marker-based and markerless systems.Given running speed not only affects sports performance but is also associated with clinical injury prevention,diagnosis,and rehabilitation,we aimed to investigate the effects of speed on the comparison of estimated lower extremity joint moments and powers between markerless and marker-based technologies during treadmill running as a concurrent validating study.Methods:Kinematic data from marker-based/markerless technologies were collected,along with ground reaction force data,from 16 young adults running on an instrumented treadmill at 3 speeds:2.24 m/s,2.91 m/s,and 3.58 m/s(5.0 miles/h,6.5 miles/h,and 8.0 miles/h).Sagittal plane moments and powers of the hip,knee,and ankle were calculated by inverse dynamic methods.Time series analysis and statistical parametric mapping were used to determine system differences.Results:Compared to the marker-based system,the markerless system estimated increased lower extremity joint kinetics with faster speed during the swing phase in most cases.Conclusion:Despite the promising application of markerless technology in clinical settings,systematic markerless overestimation requires focused attention.Based on segment pose estimations,the centers of mass estimated by markerless technologies were farther away from the relevant distal joint centers,which led to greater joint moments and powers estimates by markerless vs.marker-based systems.The differences were amplified by running speed.

Enhanced picosecond terahertz wave generation based on cascade effects in a terahertz parametric generator

Enhanced terahertz wave generation via a Stokes cascade process has been demonstrated using picosecond pulse pumped terahertz parametric generation at 1 kHz repetition rate.Clear cascade saturation of terahertz output was observed,and the corresponding cascade-Stokes spectra were analyzed.The maximum terahertz wave average power was 22μW under a pump power of 30 W,whereas the maximum power conversion efficiency was 8×10^(-7)under a pump power of 21 W.The THz power fluctuation was measured to be about 1%in 20 min.This THz parametric source with a relatively stable output is suitable for a variety of practical applications.

Nonlinear vibration of Timoshenko FG porous sandwich beams subjected to a harmonic axial load

In this study,the instability and bifurcation diagrams of a functionally graded(FG)porous sandwich beam on an elastic,viscous foundation which is influenced by an axial load,are investigated with an analytical attitude.To do so,the Timoshenko beam theory is utilized to take the shear deformations into account,and the nonlinear Von-Karman approach is adopted to acquire the equations of motion.Then,to turn the partial differential equations(PDEs)into ordinary differential equations(ODEs)in the case of equations of motion,the method of Galerkin is employed,followed by the multiple time scale method to solve the resulting equations.The impact of parameters affecting the response of the beam,including the porosity distribution,porosity coefficient,temperature increments,slenderness,thickness,and damping ratios,are explicitly discussed.It is found that the parameters mentioned above affect the bifurcation points and instability of the sandwich porous beams,some of which,including the effect of temperature and porosity distribution,are less noticeable.

Active Fault Tolerant Nonsingular Terminal Sliding Mode Control for Electromechanical System Based on Support Vector Machine

Effective fault diagnosis and fault-tolerant control method for aeronautics electromechanical actuator is concerned in this paper.By borrowing the advantages of model-driven and data-driven methods,a fault tolerant nonsingular terminal sliding mode control method based on support vector machine(SVM)is proposed.A SVM is designed to estimate the fault by off-line learning from small sample data with solving convex quadratic programming method and is introduced into a high-gain observer,so as to improve the state estimation and fault detection accuracy when the fault occurs.The state estimation value of the observer is used for state reconfiguration.A novel nonsingular terminal sliding mode surface is designed,and Lyapunov theorem is used to derive a parameter adaptation law and a control law.It is guaranteed that the proposed controller can achieve asymptotical stability which is superior to many advanced fault-tolerant controllers.In addition,the parameter estimation also can help to diagnose the system faults because the faults can be reflected by the parameters variation.Extensive comparative simulation and experimental results illustrate the effectiveness and advancement of the proposed controller compared with several other main-stream controllers.

Parametric instability in the pure-quartic nonlinear Schrödinger equation

We study the nonlinear stage of modulation instability(MI)in the non-intergrable pure-quartic nonlinear Schrödinger equation where the fourth-order dispersion is modulated periodically.Using the three-mode truncation,we reveal the complex recurrence of parametric resonance(PR)breathers,where each recurrence is associated with two oscillation periods(PR period and internal oscillation period).The nonlinear stage of parametric instability admits the maximum energy exchange between the spectrum sidebands and central mode occurring outside the MI gain band.

Parametric resonance of axially functionally graded pipes conveying pulsating fluid

Based on the generalized Hamilton's principle,the nonlinear governing equation of an axially functionally graded(AFG)pipe is established.The non-trivial equilibrium configuration is superposed by the modal functions of a simply supported beam.Via the direct multi-scale method,the response and stability boundary to the pulsating fluid velocity are solved analytically and verified by the differential quadrature element method(DQEM).The influence of Young's modulus gradient on the parametric resonance is investigated in the subcritical and supercritical regions.In general,the pipe in the supercritical region is more sensitive to the pulsating excitation.The nonlinearity changes from hard to soft,and the non-trivial equilibrium configuration introduces more frequency components to the vibration.Besides,the increasing Young's modulus gradient improves the critical pulsating flow velocity of the parametric resonance,and further enhances the stability of the system.In addition,when the temperature increases along the axial direction,reducing the gradient parameter can enhance the response asymmetry.This work further complements the theoretical analysis of pipes conveying pulsating fluid.

Overshoot phenomena:Observation and simulation

High-power O-mode radio waves can excite artificial instabilities in the F region,according to experiments conducted at the European Incoherent Scatter Science Association(EISCAT)heating facility.The main instabilities include the parametric decay instability(PDI),oscillating two-stream instability(OTSI),and thermal parametric instability(TPI).The PDI and OTSI not only compete with each other,but also compete with the TPI,leading to a two-stage overshoot phenomenon:a miniovershoot occurs on a millisecond time scale after pump-on,followed by the main overshoot.We gain insight into the miniovershoot via a generalized Zakharov model,whereas the main overshoot can be observed as an enhanced plasma line overshoot phenomenon in incoherent scatter radar spectra.We can also observe that the zero-frequency ion line exists only in the initial heating period after a cold start and that the upshifted and downshifted ion lines behave irregularly in the spectra.The simulation results show that competition between the PDI and OTSI leads to an initial peak,which we named the pre-miniovershoot.The following processes,namely ion density caviton generation,and collapse and cascade in the development of the PDI,contribute to the miniovershoot phenomenon.

Impact of cancer diagnosis on life expectancy by area-level socioeconomic groups in New South Wales, Australia: a population-based study

Objective: Improvement in cancer survival over recent decades has not been accompanied by a narrowing of socioeconomic disparities. This study aimed to quantify the loss of life expectancy(LOLE) resulting from a cancer diagnosis and examine disparities in LOLE based on area-level socioeconomic status(SES).Methods: Data were collected for all people between 50 and 89 years of age who were diagnosed with cancer, registered in the NSW Cancer Registry between 2001 and 2019, and underwent mortality follow-up evaluations until December 2020. Flexible parametric survival models were fitted to estimate the LOLE by gender and area-level SES for 12 common cancers.Results: Of 422,680 people with cancer, 24% and 18% lived in the most and least disadvantaged areas, respectively. Patients from the most disadvantaged areas had a significantly greater average LOLE than patients from the least disadvantaged areas for cancers with high survival rates, including prostate [2.9 years(95% CI: 2.5±3.2 years) vs. 1.6 years(95% CI: 1.3±1.9 years)] and breast cancer [1.6 years(95% CI: 1.4±1.8 years) vs. 1.2 years(95% CI: 1.0±1.4 years)]. The highest average LOLE occurred in males residing in the most disadvantaged areas with pancreatic [16.5 years(95% CI: 16.1±16.8 years) vs. 16.2 years(95% CI: 15.7±16.7 years)] and liver cancer [15.5 years(95% CI: 15.0±16.0 years) vs. 14.7 years(95% CI: 14.0±15.5 years)]. Females residing in the least disadvantaged areas with thyroid cancer [0.9 years(95% CI: 0.4±1.4 years) vs. 0.6 years(95% CI: 0.2±1.0 years)] or melanoma [0.9 years(95% CI: 0.8±1.1 years) vs. 0.7 years(95% CI: 0.5±0.8 years)] had the lowest average LOLE.Conclusions: Patients from the most disadvantaged areas had the highest LOLE with SES-based differences greatest for patients diagnosed with cancer at an early stage or cancers with higher survival rates, suggesting the need to prioritise early detection and reduce treatment-related barriers and survivorship challenges to improve life expectancy.

Nonlinear dynamics of a circular curved cantilevered pipe conveying pulsating fluid based on the geometrically exact model

Due to the novel applications of flexible pipes conveying fluid in the field of soft robotics and biomedicine,the investigations on the mechanical responses of the pipes have attracted considerable attention.The fluid-structure interaction(FSI)between the pipe with a curved shape and the time-varying internal fluid flow brings a great challenge to the revelation of the dynamical behaviors of flexible pipes,especially when the pipe is highly flexible and usually undergoes large deformations.In this work,the geometrically exact model(GEM)for a curved cantilevered pipe conveying pulsating fluid is developed based on the extended Hamilton's principle.The stability of the curved pipe with three different subtended angles is examined with the consideration of steady fluid flow.Specific attention is concentrated on the large-deformation resonance of circular pipes conveying pulsating fluid,which is often encountered in practical engineering.By constructing bifurcation diagrams,oscillating shapes,phase portraits,time traces,and Poincarémaps,the dynamic responses of the curved pipe under various system parameters are revealed.The mean flow velocity of the pulsating fluid is chosen to be either subcritical or supercritical.The numerical results show that the curved pipe conveying pulsating fluid can exhibit rich dynamical behaviors,including periodic and quasi-periodic motions.It is also found that the preferred instability type of a cantilevered curved pipe conveying steady fluid is mainly in the flutter of the second mode.For a moderate value of the mass ratio,however,a third-mode flutter may occur,which is quite different from that of a straight pipe system.

Harmonic balance simulation of the influence of component uniformity and reliability on the performance of a Josephson traveling wave parametric amplifier

A Josephson traveling wave parametric amplifier(JTWPA),which is a quantum-limited amplifier with high gain and large bandwidth,is the core device of large-scale measurement and control systems for quantum computing.A typical JTWPA consists of thousands of Josephson junctions connected in series to form a transmission line and hundreds of shunt LC resonators periodically loaded along the line for phase matching.Because the variation of these capacitors and inductors can be detrimental to their high-frequency characteristics,the fabrication of a JTWPA typically necessitates precise processing equipment.To guide the fabrication process and further improve the design for manufacturability,it is necessary to understand how each electronic component affects the amplifier.In this paper,we use the harmonic balance method to conduct a comprehensive study on the impact of nonuniformity and fabrication yield of the electronic components on the performance of a JTWPA.The results provide insightful and scientific guidance for device design and fabrication processes.