Effects of five typical heat treatment processes on the damping properties and the damping peak of 6061Al/SiC p MMC fabricated by spray codeposition were studied. The results show that the internal friction spectra of...Effects of five typical heat treatment processes on the damping properties and the damping peak of 6061Al/SiC p MMC fabricated by spray codeposition were studied. The results show that the internal friction spectra of various heat treated samples exhibit the damping peak versus temperature between 130 ℃ and 200 ℃. Furthermore, the peak temperature as well as the peak height increases with increasing frequencies. By Arrhenius equation the active energy of the damping peak can be gotten, which is above 1 eV. On the other hand, different quenching treatments affect the damping peak remarkably, when the rate of cooling is above that of water quenching, the damping peak will shift to higher temperature as cooling speed is enhanced.展开更多
In order to veritably measure the first peak of hydration heat evolution that has been illustrated important in indicating cement behavior in early hydration, an improved way of water addition into cement in isotherma...In order to veritably measure the first peak of hydration heat evolution that has been illustrated important in indicating cement behavior in early hydration, an improved way of water addition into cement in isothermally calorimetric experiment is put forward. The experimental results indicated that: the magnitude of first peak of heat evolution varies from sample to sample, correlation between heat evolution during first peak of heat evolution and initial (as well as final) setting time is unsatisfactory when samples are not classified; while groups of sample classified based on strength grade represent satisfactory correlations, which indicating the existence of close relation between hydration heat evolution in much earlier hydration age and setting property of cement in rather later age. Importance of first peak in hydration heat evolution for understanding cement setting property and reasons for sample classification are also discussed in this paper.展开更多
The low temperature specific heat of Sm-AI-Co ternary metallic glasses is investigated and a clear anomaly associated with the Boson peak is identified. While this anomaly depends slightly on the chemical composition,...The low temperature specific heat of Sm-AI-Co ternary metallic glasses is investigated and a clear anomaly associated with the Boson peak is identified. While this anomaly depends slightly on the chemical composition, it has no dependence on external magnetic field. To figure out the mechanism of the Boson peak, we interpret the data within various model frameworks. Unlike earlier work, our study shows that this Boson peak is mainly ascribed to an additional T2 term of the specific heat, which may originate from the quasi-two-dimensional and short-range ordered structure units possibly existing in the metallic glasses.展开更多
Considering the basic heat transfer rules of superfluid helium and the phase diagram of helium, pressure effects on heat transfer to HeⅡ are especially studied. If the bath pressure is less than λ pressure ...Considering the basic heat transfer rules of superfluid helium and the phase diagram of helium, pressure effects on heat transfer to HeⅡ are especially studied. If the bath pressure is less than λ pressure ( P λ ), special peak heat flux density relations are shown to correlate bath pressure, hydrostatic head and modified pressure items (Van der waals pressure and fountain pressure). If the bath pressure is greater than λ pressure( P>P λ), a generalized formula of peak flux density of HeⅡp bath is shown.展开更多
In order to accurately predict the incident critical heat flux（ICHF,the heat flux at the heated surface when CHF occurs） of a water-cooled W/Cu monoblock for a divertor,the exact knowledge of its peaking factors（f_...In order to accurately predict the incident critical heat flux（ICHF,the heat flux at the heated surface when CHF occurs） of a water-cooled W/Cu monoblock for a divertor,the exact knowledge of its peaking factors（f_p） under one-sided heating conditions with different design parameters is a key issue.In this paper,the heat conduction in the solid domain of a water-cooled W/Cu monoblock is calculated numerically by assuming the local heat transfer coefficients（HTC）of the cooling wall to be functions of the local wall temperature,so as to obtain f_p.The reliability of the calculation method is validated by an experimental example result,with the maximum error of 2.1% only.The effects of geometric and flow parameters on the f_p of a water-cooled W/Cu monoblock are investigated.Within the scope of this study,it is shown that the f_p increases with increasing dimensionless W/Cu monoblock width and armour thickness（the shortest distance between the heated surface and Cu layer）,and the maximum increases are 43.8% and 22.4% respectively.The dimensionless W/Cu monoblock height and Cu thickness have little effect on f_p.The increase of Reynolds number and Jakob number causes the increase of f_p,and the maximum increases are 6.8% and 9.6% respectively.Based on the calculated results,an empirical correlation on peaking factor is obtained via regression.These results provide a valuable reference for the thermal-hydraulic design of water-cooled divertors.展开更多
文摘Effects of five typical heat treatment processes on the damping properties and the damping peak of 6061Al/SiC p MMC fabricated by spray codeposition were studied. The results show that the internal friction spectra of various heat treated samples exhibit the damping peak versus temperature between 130 ℃ and 200 ℃. Furthermore, the peak temperature as well as the peak height increases with increasing frequencies. By Arrhenius equation the active energy of the damping peak can be gotten, which is above 1 eV. On the other hand, different quenching treatments affect the damping peak remarkably, when the rate of cooling is above that of water quenching, the damping peak will shift to higher temperature as cooling speed is enhanced.
基金Funded by Guangxi Science Foundation(No. 0639006)
文摘In order to veritably measure the first peak of hydration heat evolution that has been illustrated important in indicating cement behavior in early hydration, an improved way of water addition into cement in isothermally calorimetric experiment is put forward. The experimental results indicated that: the magnitude of first peak of heat evolution varies from sample to sample, correlation between heat evolution during first peak of heat evolution and initial (as well as final) setting time is unsatisfactory when samples are not classified; while groups of sample classified based on strength grade represent satisfactory correlations, which indicating the existence of close relation between hydration heat evolution in much earlier hydration age and setting property of cement in rather later age. Importance of first peak in hydration heat evolution for understanding cement setting property and reasons for sample classification are also discussed in this paper.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 50601013, 10674061 and 50832002)the National Basic Research Program of China (Grant No. 2006CB921802)
文摘The low temperature specific heat of Sm-AI-Co ternary metallic glasses is investigated and a clear anomaly associated with the Boson peak is identified. While this anomaly depends slightly on the chemical composition, it has no dependence on external magnetic field. To figure out the mechanism of the Boson peak, we interpret the data within various model frameworks. Unlike earlier work, our study shows that this Boson peak is mainly ascribed to an additional T2 term of the specific heat, which may originate from the quasi-two-dimensional and short-range ordered structure units possibly existing in the metallic glasses.
基金the National Natural Science Foundation of China
文摘Considering the basic heat transfer rules of superfluid helium and the phase diagram of helium, pressure effects on heat transfer to HeⅡ are especially studied. If the bath pressure is less than λ pressure ( P λ ), special peak heat flux density relations are shown to correlate bath pressure, hydrostatic head and modified pressure items (Van der waals pressure and fountain pressure). If the bath pressure is greater than λ pressure( P>P λ), a generalized formula of peak flux density of HeⅡp bath is shown.
基金supported by National Magnetic Confinement Fusion Science Program of China(No.2010GB104005)Funding of Jiangsu Innovation Program for Graduate Education,China(CXLX12_0170)the Fundamental Research Funds for the Central Universities of China
文摘In order to accurately predict the incident critical heat flux（ICHF,the heat flux at the heated surface when CHF occurs） of a water-cooled W/Cu monoblock for a divertor,the exact knowledge of its peaking factors（f_p） under one-sided heating conditions with different design parameters is a key issue.In this paper,the heat conduction in the solid domain of a water-cooled W/Cu monoblock is calculated numerically by assuming the local heat transfer coefficients（HTC）of the cooling wall to be functions of the local wall temperature,so as to obtain f_p.The reliability of the calculation method is validated by an experimental example result,with the maximum error of 2.1% only.The effects of geometric and flow parameters on the f_p of a water-cooled W/Cu monoblock are investigated.Within the scope of this study,it is shown that the f_p increases with increasing dimensionless W/Cu monoblock width and armour thickness（the shortest distance between the heated surface and Cu layer）,and the maximum increases are 43.8% and 22.4% respectively.The dimensionless W/Cu monoblock height and Cu thickness have little effect on f_p.The increase of Reynolds number and Jakob number causes the increase of f_p,and the maximum increases are 6.8% and 9.6% respectively.Based on the calculated results,an empirical correlation on peaking factor is obtained via regression.These results provide a valuable reference for the thermal-hydraulic design of water-cooled divertors.
