Optimal Dispatch for Battery Energy Storage Station in Distribution Network Considering Voltage Distribution Improvement and Peak Load Shifting

Distribution networks are commonly used to demonstrate low-voltage problems.A new method to improve voltage quality is using battery energy storage stations(BESSs),which has a four-quadrant regulating capacity.In this paper,an optimal dispatching model of a distributed BESS considering peak load shifting is proposed to improve the voltage distribution in a distribution network.The objective function is to minimize the power exchange cost between the distribution network and the transmission network and the penalty cost of the voltage deviation.In the process,various constraints are considered,including the node power balance,single/two-way power flow,peak load shifting,line capacity,voltage deviation,photovoltaic station operation,main transformer capacity,and power factor of the distribution network.The big M method is used to linearize the nonlinear variables in the objective function and constraints,and the model is transformed into a mixed-integer linear programming problem,which significantly improves the model accuracy.Simulations are performed using the modified IEEE 33-node system.A typical time period is selected to analyze the node voltage variation,and the results show that the maximum voltage deviation can be reduced from 14.06%to 4.54%.The maximum peak-valley difference of the system can be reduced from 8.83 to 4.23 MW,and the voltage qualification rate can be significantly improved.Moreover,the validity of the proposed model is verified through simulations.

Pressure effect study on the Ⅰ-Ⅴ property of the GaAs-based resonant tunnelling structure by photoluminescence measurement

This paper discusses the I-V property of the GaAs-based resonant tunnelling structure （RTS） under external uniaxial pressure by photoluminescence studies. Compressive pressure parallel to the [110] direction, whose value is determined by Hooke＇s law, is imposed on the sample by a helix micrometer. With the increase of the applied external uniaxial compressive pressure, the blue shift and splitting of the luminescence peaks were observed, which have some influence on the I-V curve of RTS from the point of view of the energy gap, and the splitting became more apparent with applied pressure. Full width at half maximum broadening could also be observed.

Nonepitaxial growth of a (001) textured L1_0 Fe-Pt film in H_2 and N_2 annealing atmospheres

A nonepitaxial （001） textured Fe-Pt alloyed film was obtained by annealing Fe/Pt multilayers in H2. No Such nonepitaxial （001） texture was observed for similar multilayers annealed in N2 atmosphere. Sensitive electron energy loss spectroscopy and the left shift of the L10 FePt （111） diffr cfion peak indicate oxidation in the N2 annealed samples. The oxidation dramatically degrades the （001） texture of the Fe-Pt fdm and induces the composition change in the alloyed layer. The relation between the texture formation and oxidation was discussed.

Conditions and Phase Shift of Fluid Resonance in Narrow Gaps of Bottom Mounted Caissons

This paper studies the viscid and inviscid fluid resonance in gaps of bottom mounted caissons onthe basis of the plane wave hypothesis and full wave model, The theoretical analysis and the numerical results demonstrate that the condition for the appearance of fluid resonance in narrow gaps is kh=（2n＋1）π （n=0, 1, 2, 3 ）, rather than kh=nn （n=0, 1, 2, 3, ...）; the transmission peaks in viscid fluid are related to the resonance peaks in the gaps. k and h stand for the wave number and the gap length. The combination of the plane wave hypothesis or the full wave model with the local viscosity model can accurately determine the heights and the locations of the resonance peaks. The upper bound for the appearance of fluid resonance in gaps is 2b/L〈l （2b, grating constant; L, wave length） and the lower bound is h/b〈~ l. The main reason for the phase shift of the resonance peaks is the inductive factors. The number of resonance peaks in the spectrum curve is dependent on the ratio of the gap length to the grating constant. The heights and the positions of the resonance peaks predicted by the present models agree well with the experimental data.

Empirical investigation to explore potential gains from the amalgamation of phase changing materials(PCMs)and wood shavings

The reduction of gained heat,heat peak shifting,and the mitigation of air temperature fluctuations are some desirable properties that are sought after in any thermal insulation system.It cannot be overstated that these fac-tors,in addition to others,govern the performance of such systems thus their effect on indoor ambient conditions.The effect of such systems extends also to Heating,Ventilation and Air-conditioning(HVAC)systems that are set up to operate optimally in certain conditions.Where literature shows that PCMs and natural materials such as wood-shavings can provide efficient passive insulation for buildings,it is evident that such approaches utilise methods that are of a degree of intricacy which require specialist knowledge and complex techniques,such as micro-encapsulation for instance.With technical and economic aspects in mind,an amalgam of PCM and wood-shavings has been created to be utilised as a feasible thermal insulation.The amalgamation was performed in the simplest of methods,through submerging the wood shavings in PCM.An experimental procedure was devised to test the thermal performance of the amalgam and compare this to the performance of the same un-amalgamated materials.Comparative analysis revealed that no significant thermal gains would be expected from such amal-gamation.However,a significant reduction in the total weight of the insulation system would be achieved that,in this case,shown to be up to 20.94%.Thus,further reducing possible strains on structural elements due to the application of insulation on buildings.This can be especially beneficial in vernacular architectural approaches where considerably large amounts and thicknesses of insulations are used.In addition,cost reduction could be attained as wood shavings are significantly cheaper compared to the cost of PCMs.