Simulation of deuterium pellet ablation and deposition in the EAST tokamak with HPI2 code

Pellet injection is a primary method for fueling the plasma in magnetic confinement devices.For that goal the knowledges of pellet ablation and deposition profiles are critical.In the present study,the pellet fueling code HPI2 was used to predict the ablation and deposition profiles of deuterium pellets injected into a typical H-mode discharge on the EAST tokamak.Pellet ablation and deposition profiles were evaluated for various pellet injection locations,with the aim at optimizing the pellet injection to obtain a deep fueling depth.In this study,we investigate the effect of the injection angle on the deposition depth of the pellet at different velocities and sizes.The ablation and deposition of the injected pellet are mainly studied at each injection position for three different injection angles:0°,45°,and 60°.The pellet injection on the high field side(HFS)can achieve a more ideal deposition depth than on the low field side(LFS).Among these angles,horizontal injection on the middle plane is relatively better on either the HFS or the LFS.When the injection location is 0.468 m below the middle plane on the HFS or 0.40 m above the middle plane of the LFS,it can achieve a similar deposition depth to the one of its corresponding side.When the pre-cooling effect is taken into account,the deposition depth is predicted to increase only slightly when the pellet is launched from the HFS.The findings of this study will serve as a reference for the update of pellet injection systems for the EAST tokamak.

High-chromium vanadium-titanium magnetite all-pellet integrated burden optimization and softening-melting behavior based on flux pellets

High-chromium vanadium-titanium magnetite(HVTM)is a crucial polymetallic-associated resource to be developed.The allpellet operation is a blast furnace trend that aims to reduce carbon dioxide emissions in the future.By referencing the production data of vanadium-titanium magnetite blast furnaces,this study explored the softening-melting behavior of high-chromium vanadium-titanium magnetite and obtained the optimal integrated burden based on flux pellets.The results show that the burden with a composition of 70wt%flux pellets and 30wt%acid pellets exhibits the best softening-melting properties.In comparison to that of the single burden,the softening-melting characteristic temperature of this burden composition was higher.The melting interval first increased from 307 to 362℃and then decreased to 282℃.The maximum pressure drop(ΔPmax)decreased from 26.76 to 19.01 kPa.The permeability index(S)dropped from 4643.5 to 2446.8 kPa·℃.The softening-melting properties of the integrated burden were apparently improved.The acid pellets played a role in withstanding load during the softening process.The flux pellets in the integrated burden exhibited a higher slag melting point,which increased the melting temperature during the melting process.The slag homogeneity and the TiC produced by over-reduction led to the gas permeability deterioration of the single burden.The segregation of the flux and acid pellets in the HVTM proportion and basicity mainly led to the better softening-melting properties of the integrated burden.

Pelleting and particle size reduction of corn increase net energy and digestibility of fiber,protein,and fat in corn-soybean meal diets fed to group-housed pigs

Background Reduction of the particle size of corn increases energy digestibility and concentrations of digestible and metabolizable energy.Pelleting may also reduce particle size of grain,but it is not known if there are interactions between particle size reduction and pelleting.The objective of this experiment was to test the hypothesis that particle size reduction and pelleting,separately or in combination,increase N balance,apparent total tract digestibility(ATTD)of fiber and fat,and net energy(NE)in corn-soybean meal diets fed to group-housed pigs.Methods Six corn-soybean meal-based diets were used in a 3×2 factorial design with 3 particle sizes of corn(i.e.,700,500,or 300μm)and 2 diet forms(i.e.,meal or pelleted).Pigs were allowed ad libitum access to feed and water.Twenty-four castrated male pigs(initial weight:29.52 kg;standard diviation:1.40)were allotted to the 6 diets using a 6×6 Latin square design with 6 calorimeter chambers(i.e.,4 pigs/chamber)and 6 periods.Oxygen consumption and CO_(2)and CH_(4)productions were measured during fed and fasting states and fecal and urine samples were collected.Results Regardless of particle size of corn,the ATTD of gross energy(GE),N,and acid-hydrolyzed ether extract(AEE),and the concentration of NE were greater(P<0.05)in pelleted diets than in meal diets.Regardless of diet form,the ATTD of GE,N,and AEE,and the concentration of NE were increased(linear;P<0.05)by reducing the particle size of corn,but the increase was greater in meal diets than in pelleted diets(interaction;P<0.05).Conclusions Both pelleting and reduction of corn particle size increased nutrient digestibility and NE,but increases were greater in meal diets than in pelleted diets.

Effect of titanium on the sticking of pellets based on hydrogen metallurgy shaft furnace:Behavior analysis and mechanism evolution

Direct reduction based on hydrogen metallurgical gas-based shaft furnace is a promising technology for the efficient and low-carbon smelting of vanadium-titanium magnetite.However,in this process,the sticking of pellets occurs due to the aggregation of metal-lic iron between the contact surfaces of adjacent pellets and has a serious negative effect on the continuous operation.This paper presents a detailed experimental study of the effect of TiO2 on the sticking behavior of pellets during direct reduction under different conditions.Results showed that the sticking index(SI)decreased linearly with the increasing TiO2 addition.This phenomenon can be attributed to the increase in unreduced FeTiO3 during reduction,leading to a decrease in the number and strength of metallic iron interconnections at the sticking interface.When the TiO2 addition amount was raised from 0 to 15wt%at 1100°C,the SI also increased from 0.71%to 59.91%.The connection of the slag phase could be attributed to the sticking at a low reduction temperature,corresponding to the low sticking strength.Moreover,the interconnection of metallic iron became the dominant factor,and the SI increased sharply with the increase in re-duction temperature.TiO2 had a greater effect on SI at a high reduction temperature than at a low reduction temperature.

Diffusion and reaction mechanism of limestone and quartz in fluxed iron ore pellet roasting process

The increase to the proportion of fluxed pellets in the blast furnace burden is a useful way to reduce the carbon emissions in the ironmaking process.In this study,the interaction between calcium carbonate and iron ore powder and the mineralization mechanism of fluxed iron ore pellet in the roasting process were investigated through diffusion couple experiments.Scanning electron microscopy with energy dispersive spectroscopy was used to study the elements’diffusion and phase transformation during the roasting process.The results indicated that limestone decomposed into calcium oxide,and magnetite was oxidized to hematite at the early stage of preheating.With the increase in roasting temperature,the diffusion rate of Fe and Ca was obviously accelerated,while the diffusion rate of Si was relatively slow.The order of magnitude of interdiffusion coefficient of Fe_(2)O_(3)-CaO diffusion couple was 10^(−10) m^(2)·s^(−1) at a roasting temperature of 1200℃for 9 h.Ca_(2)Fe_(2)O_(5) was the initial product in the Fe_(2)O_(3)-CaO-SiO_(2) diffusion interface,and then Ca_(2)Fe_(2)O_(5) continued to react with Fe_(2)O_(3) to form CaFe_(2)O_(4).With the expansion of the diffusion region,the sillico-ferrite of calcium liquid phase was produced due to the melting of SiO_(2) into CaFe_(2)O_(4),which can strengthen the consolidation of fluxed pellets.Furthermore,andradite would be formed around a small part of quartz particles,which is also conducive to the consolidation of fluxed pellets.In addition,the principle diagram of limestone and quartz diffusion reaction in the process of fluxed pellet roasting was discussed.

Persicaria lanigera (Polygonaceae) leaf extract exhibits antiulcerogenic and antiproliferative activities against acetic acid-induced ulcerative colitis and cotton pellet-induced granuloma tissue in rats

Objective:To assess the effect of leaf extract of Persicaria lanigera on cotton pellet-induced granuloma tissue formation and acetic acid-induced ulcerative colitis.Methods:Rats were randomly divided into six groups:normal control,negative control,positive control(dexamethasone or sulfasalazine)as well as Persicaria lanigera(100-600 mg/kg)-treated groups.The effects of the extracts on body weight,antioxidant,and hematological parameters,as well as mast cell proliferation,were assessed.In addition,a histological evaluation was conducted.Results:Persicaria lanigera extract significantly decreased the mean exudate amount and suppressed granuloma tissue formation in a concentration-dependent manner in rats(P<0.05).Additionally,the extract significantly increased body weight,improved hematological profile,reduced the disease activity index score and malondialdehyde level,as well as enhanced catalase and superoxide dismutase activities(P<0.05).Histological evaluation showed Persicaria lanigera extract alleviated acetic acid-induced colonic damages,as evidenced by decreased cell necrosis,edema,and inflammatory cell infiltration.Conclusions:Persicaria lanigera extract possesses antiproliferative,antioxidative,and anti-colitis activities.However,its underlying mechanisms of action need further investigation.

Probing deactivation by coking in catalyst pellets for dry reforming of methane using a pore network model

Dry reforming of methane(DRM) is an attractive technology for utilizing the greenhouse gases(CO_(2) and CH_(4)) to produce syngas. However, the catalyst pellets for DRM are heavily plagued by deactivation by coking, which prevents this technology from commercialization. In this work, a pore network model is developed to probe the catalyst deactivation by coking in a Ni/Al_(2)O_(3) catalyst pellet for DRM. The reaction conditions can significantly change the coking rate and then affect the catalyst deactivation. The catalyst lifetime is higher under lower temperature, pressure, and CH_(4)/CO_(2) molar ratio, but the maximum coke content in a catalyst pellet is independent of these reaction conditions. The catalyst pellet with larger pore diameter, narrower pore size distribution and higher pore connectivity is more robust against catalyst deactivation by coking, as the pores in this pellet are more difficult to be plugged or inaccessible.The maximum coke content is also higher for narrower pore size distribution and higher pore connectivity, as the number of inaccessible pores is lower. Besides, the catalyst pellet radius only slightly affects the coke content, although the diffusion limitation increases with the pellet radius. These results should serve to guide the rational design of robust DRM catalyst pellets against deactivation by coking.

Effect mechanism of aluminum occurrence and content on the induration characteristics of iron ore pellets

With the intensified depletion of high-grade iron ores,the increased aluminum content in iron ore concentrates has become unavoidable,which is detrimental to the pelletization process.Therefore,the effect mechanism of aluminum on pellet quality must be identified.In this study,the influence of aluminum occurrence and content on the induration of hematite(H)and magnetite(M)pellets was investigated through the addition of corresponding Al-containing additives,including alumina,alumogoethite,gibbsite,and kaolinite.Systematic mineralogical analysis,combined with the thermodynamic properties of different aluminum occurrences and the quantitative characterization of consolidation behaviors,were conducted to determine the related mechanism.The results showed that the alumina from various aluminum occurrences adversely affected the induration characteristics of pellets,especially at an aluminum content of more than 2.0wt%.The thermal decomposition of gibbsite and kaolinite tends to generate internal stress and fine cracks,which hinder the respective microcrystalline bonding and recrystallization between Fe2O3particles.The adverse effect on the induration characteristics of fired pellets with different aluminum occurrences can be relieved to varying degrees through the formation of liquid phase bonds between the hematite particles.Kaolinite is more beneficial to the induration process than the other three aluminum occurrences because of the formation of more liquid phase,which improves pellet consolidation.The research results can further provide insights into the effect of aluminum occurrence and content in iron ore concentrates on downstream processing and serve as a guide for the utilization of high-alumina iron ore concentrates in pelletization.

Elucidating the suppression of lithium dendrite growth with a void-reduced anti-perovskite solid-state electrolyte pellet for stable lithium metal anodes

Solid-state lithium-metal batteries,with their high theoretical energy density and safety,are highly promising as a next-generation battery contender.Among the alternatives proposed as solid-state electrolyte,lithium-rich anti-perovskite(Li RAP)materials have drawn the most interest because of high theoretical Li^(+)conductivity,low cost and easy processing.Although solid-state electrolytes are believed to have the potential to physically inhibit the lithium dendrite growth,lithium-metal batteries still suffer from the lithium dendrite growth and thereafter the short circuiting.The voids in practical Li RAP pellets are considered as the root cause.Herein,we show that reducing the voids can effectively suppress the lithium dendrite growth.The voids in the pellet resulted in an irregular Li^(+)flux distribution and a poor interfacial contact with lithium metal anode;and hence the ununiform lithium dendrites.Consequently,the lithium-metal symmetric cell with void-reduced Li_(2)OHCl-HT pellet was able to display excellent cycling performance(750 h at 0.4 m A cm^(-2))and stability at high current density(0.8 m A cm^(-2)for 120 h).This study provides not only experimental evidence for the impact of the voids in Li RAP pellets on the lithium dendrite growth,but also a rational pellet fabrication approach to suppress the lithium dendrite growth.

Hydrochar Pelletization towards Solid Biofuel from Biowaste Hydrothermal Carbonization

Hydrothermal carbonization is highly applicable to high moisture biomass upgrading due to the fact that moist-ure involved can be directly used as reaction media under the subcritical-water region.With this,value-added utilization of hydrochar as solid fuel with high carbon and energy density is one of the important pathways for biomass conversion.In this review,the dewatering properties of hydrochar after the hydrothermal carbonization of biowaste,coalification degree with elemental composition and evolution,pelletization of hydrochar to enhance the mechanical properties and density,coupled with the combustion properties of hydrochar biofuel were discussed with various biomass and carbonization parameters.Potential applications for the co-combustion with coal,cleaner properties and energy balance for biowaste hydrothermal carbonization were presented as well as the challenges.

The Logistics of Production and Supply of Ag Pellets for Industrial Applications in Canada

In this work we analyze the supply of biomass from field to an in-land or port destination. The biomass is pelletized to increase its bulk density to extend its storage period and for ease of its transport. The pellet may be used for conversion to chemicals and animal bedding or for straight combustion. We analyzed supply chain in Saskatchewan where there are plenty of crop residues but widely dispersed and harvest seasons are short. We envisioned that the farmer collects bales from field and transports the bales to farmstead during the harvest season. The bales are then processed into pellets using small scale pellet equipment. A custom operator with expertise in pelletization may engage in handling and densifying the biomass. The business case for the mobile mill will be similar to the well established custom grain and forage harvesting operations. The pellets are stored in hopper bottom grain bins at the farmstead. From this point, the handling of pellets would be similar to the handling and marketing of grain. The farmer trucks a specified volume of pellets from farmstead to the nearest elevator where the pellets are transferred to larger bins or silos. Pellets are extracted from silos and loaded onto the rail cars. The Canadian freight rail companies (mainly CN) currently transport over 3 million dry tonne (dt) of wood pellets in rail cars. The pellets are hauled to marine ports on the West Coast or East Coast for export. The cost of delivering ag pellets to biorefinery or to the shipping port is $86.09/dt. This cost does not include the equivalent value of removing biomass from the farm (e.g. fertilizer replacement) and return on investment. The GHG emissions to produce and transport ag pellets add up to 185.9 kg of CO2 per dt of biomass. The cost of producing pellets without drying feedstock is $35.05/dt and the corresponding GHG for palletization amounts $146.30/dt.

Advanced Strategies to Mobilize Crop Residue to Replace Coal in India

Various published data show the amount of crop residue available annually in India may range from a low of 90 to a high of 180 million tonnes. Different types of crop residue are collected from farmers depending on the geography and crop pattern for instance, in north India rice straw and cotton stalks are collected while in central India soya husk and sugarcane tops are collected. Baling and transporting straw from the field, though appear to be an option for safe disposal, will be feasible only when alternate, effective and economically viable usage methods are identified and facilities and infrastructure for ex-situ management methods are created. One immediate short term use of the residue is to replace 5% - 7% of the 670 million tonnes of coal India currently consumes to generate power. The farmers will benefit from the sale of their excess crop residue. The scheme will reduce pollution due to residue burning practices. Replacing coal will cut the GHG emissions. The challenge is to mobilize the crop residue collection and timely delivery to power plants. The data and calculations in this monogram show that it is economical for the farmer to remove the crop residue from the field quickly by using modern balers, to pelletize the biomass in small-scale distributed pellet plants, to store pellets in the modern steel bins and finally to deliver the pellets to coal plants by using rail transport. The delivered cost is estimated at around Rp 6.78/kg. The Government of India encourages the power plants to pay at least Rp 10/kg for the delivered biomass in the form of pellets. The current monogram analyzes the organization of an efficient supply chain in the State of Haryana India to ensure a sustainable modern enterprise.

The Application of Electron-Beam Welding in Pellet Mold Preparation

This paper provides insight into the application of electron-beam welding in pellet mold preparation,highlighting the importance of the combination of electron-beam welding and pellet mold preparation in the fields of microstructure joining and micro-and nanostructure preparation.Precise material joining and microstructure fabrication can be achieved by the precise control of electron-beam welding and the shape adjustment of pellet molds.These applications hold significant potential in the modern industrial field,providing robust support for the development of new materials and the growth of the petrochemical industry.This paper asserts that in the future,the ongoing development of electron-beam welding and pelletizing template technology will unlock new possibilities in the field of petrochemicals,fostering progress in science and technology.

本体的推理研究

针对OWL所描述的本体,介绍了本体推理机的构成,重点阐述了Jena语义Web编程框架中内置的几种推理模式,并通过叠加外部推理机Pellet来弥补单一推理机在推理能力方面的不足.以一个小型本体为例,通过运用Jena内置的推理模式和叠加外部推理机的方式对本体的推理进行了探索和验证.

激活的富血小板血浆促进Pellet培养的脂肪间充质干细胞成软骨样分化

目的探讨激活的富血小板血浆(PRP)对Pellet培养的人脂肪来源间充质干细胞向软骨样细胞分化及相关信号通路的影响。方法添加不同比例(5%、10%和15%)的激活PRP,检测不同培养时间(1、3、5、7、9、11 d)脂肪干细胞的增殖能力。将采用Pellet培养的P3代的h ADSCs分为3组,对照组、激活PRP组和含TGF-β3的软骨诱导组,持续培养21 d后,阿利新蓝和苏木精-伊红染色进行软骨分化鉴定,real-time PCR测定Sox-9、Aggrecan和II型胶原的基因表达,DMMB法测定胞外基质中GAG含量,Western blot进一步检测对照组和激活PRP组中Sox-9、Gli-1和BMP-2蛋白的表达。结果 MTT实验结果显示,在10%激活PRP培养条件下,11 d的生长时间内hADSCs的增殖率最适宜。阿利新蓝和苏木精-伊红染色显示,激活PRP组和软骨诱导组中软骨表达呈阳性。Real-time PCR结果表明软骨诱导组其Sox-9、Aggrecan和II型胶原mRNA表达的能力高于激活PRP组(P<0.05)。GAG实验结果显示,软骨诱导组促GAG分泌的能力优于激活PRP组(P<0.05)。Western blot结果显示,相比对照组,激活PRP组中伴随Gli-1和BMP-2的蛋白表达升高,而Sox-9蛋白表达随之升高。结论激活PRP刺激hADSCs的最适增殖能力的浓度比例为10%。激活PRP和软骨诱导剂对脂肪干细胞成软骨分化中的诱导表达具有相似的能力,激活PRP对h ADSCs诱导成软骨作用与Hedgehog和BMP信号通路有关。

基于描述逻辑的领域本体知识逻辑检测

对本体库进行逻辑检测是本体构建的一个重要环节。基于描述逻辑的领域本体知识逻辑检测主要归结为判断概念关于TBox的可满足性以及判断ABox关于TBox的一致性。本文采用基于Tableaux算法的Pellet推理机对茶虫害本体库进行逻辑检测,验证了本体逻辑定义的有效性、完备性,为茶虫害本体的评价和二次开发以及后期应用奠定基础。

层叠推理机的设计与实现

在充分理解现有本体推理机的相关技术基础上,提出一种层叠推理机,研究层叠推理机的设计和实现方法。在实验中运用了Pellet推理机和Jena的自定义规则,实现了本体的语义推理。实验结果表明,该方法能够弥补传统推理机中采用单一的语义推理技术所引起的不足,比单一的推理机更有效地挖掘出本体中包含的隐藏信息。

自定义SWRL知识图谱推理补全插件的实现

知识图谱是人工智能应用的基石,基于规则进行推理是知识图谱知识补全的重要方式。SWRL推理插件的局限性成为了知识推理补全的瓶颈。打破了SWRL有限的推理能力,论述了在SWRL规则中编写自定义知识推理插件,并在知识图谱建模和推理工具中实现对自定义插件推理支持的方法。介绍了知识图谱知识建模和推理的方法与工具,结合一个具体的知识补全需求建模了包含自定义知识推理插件的SWRL推理规则;在Pellet推理机中实现和注入了此自定义推理插件的推理支持源码,并通过与Protégé知识建模工具进行集成从而完成知识补全需求;应用包含自定义插件的SWRL推理规则完成了老人健康小屋物联网系统资源组成和资源故障诊断的知识补全。以此论述了使用SWRL自定义知识推理插件进行知识图谱知识补全的方法和实践。

浮游动物对重金属的累积及转移

原于吸收法的测定结果表明,厦门海区几种常见浮游动物的主要重金属含量因种类而异,含Zn量30.40-291.4μg/g.dw含Cu3.620-37.62μg/g.dw,含Cd最低(0.025-1.38μg/g.dw).经一定时间培养的中华哲水蚤的累积Cu量随水体Cu浓度的增大和培养时间的延长而提高,但Cd含量则几乎不变,中华哲水蚤粪块含Cu量的比用作饵料的三角指藻高2.7-29倍,ECd含量略低于藻.桡足类可从粪块中排除相当部分进入体内的重金属,这对海洋环境的金属下移具有重要作用.

Effect of molasses binder on the physical and mechanical properties

Molasses was used as an alternative binder to the bentonite binder. The change in moisture absorption by pellets prepared with different iron ores and different molasses contents were investigated. Iron ore properties exerted the major effect on pellet behavior and final pellet quality. The absorbed moisture content of pellets prepared without binder, bentonite-added pellets, and molasses-added pellets were in the range of 7.72%–9.95%, 9.62%–10.84%, and 6.14%-6.69%, respectively. The wet pellet compressive strength of molasses-added pellets(43–230 N/pellet) was superior to that of bentonite-added pellets(9.47–11.92 N/pellet). The compressive strength of dried molasses-modified pellets increased to 222–394 N/pellet, which is currently the highest value achieved for dried pellets.