Experimental Study on the Electrochemical Performance of PEMFC under Different Assembly Forces

Proton exchange membrane fuel cell(PEMFC)is of paramount significance to the development of clean energy.The components of PEMFC are assembled using many pairs of nuts and bolts.The assembly champing bolt torque is critical to the electrochemical performance and mechanical stability of PEMFC.In this paper,a PEMFC with the threechannel serpentine flow field was used and studied.The different assembly clamping bolt torques were applied to the PEMFC in three uniform assembly bolt torque and six non-uniform assembly bolt torque conditions,respectively.And then,the electrochemical performance experiments were performed to study the effect of the assembly bolt torque on the electrochemical performance.The test results show that the assembly bolt torque significantly affected the electrochemical performance of the PEMFC.In uniform assembly bolt torque conditions,the maximal power density increased initially as the assembly bolt torque increased,and then decreased on further increasing the assembly torque.It existed the optimum assembly torque which was found to be 3.0 N·m in this work.In non-uniform assembly clamping bolt torque conditions,the optimum electrochemical performance appeared in the condition where the assembly torque of each bolt was closer to be 3.0 N·m.This could be due to the change of the contact resistance between the gas diffusion layer and bipolar plate and mass transport resistance for the hydrogen and oxygen towards the catalyst layers.This work could optimize the assembly force conditions and provide useful information for the practical PEMFC stack assembly.

Experimental Research on Output Performances of Giant Magnetostrictive Actuator

The paper introduces the performances of magnetostrictive actuators and its applications,discusses the design methods for the structure and internal magnetic circuit of a giant magnetostrictive actuator,and makes tests on the output displacement and force characteristics for an actuator using homemade magnetostrictive material.The experimental result shows that the actuator has satisfactory output precisions and ranges in transient and stable states,and can be used in low-frequency vibration control system of precise equipment.

Numerical Research on Performance Prediction for Centrifugal Pumps

Performance prediction for centrifugal pumps is now mainly based on numerical calculation and most of the studies merely focus on one model. Therefore, the research results are not representative. To make an improvement of numerical calculation method and performance prediction for centrifugal pumps, performance of six centrifugal pump models at design flow rate and off design flow rates, whose specific speed are different, were simulated by using commercial code FLUENT. The standard k-t turbulence model and SIMPLEC algorithm were chosen in FLUENT. The simulation was steady and moving reference frame was used to consider the impeller-volute interaction. Also, how to dispose the gap between impeller and volute was presented and the effect of grid number was considered. The characteristic prediction model for centrifugal pumps is established according to the simulation results. The head and efficiency of the six models at different flow rates are predicted and the prediction results are compared with the experiment results in detail. The comparison indicates that the precision of head and efficiency prediction are all less than 5%. The flow analysis indicates that flow change has an important effect on the location and area of low pressure region behind the blade inlet and the direction of velocity at impeller inlet. The study shows that using FLUENT simulation results to predict performance of centrifugal pumps is feasible and accurate. The method can be applied in engineering practice.

Influence of Blade Wrap Angle on Centrifugal Pump Performance by Numerical and Experimental Study

The existing research on improving the hydraulic performance of centrifugal pumps mainly focuses on the design method and the parameter optimization. The traditional design method for centrifugal impellers relies more on experience of engineers that typically only satisfies the continuity equation of the fluid. In this study, on the basis of the direct and inverse iteration design method which simultaneously solves the continuity and motion equations of the fluid and shapes the blade geometry by controlling the wrap angle, three centrifugal pump impellers are designed by altering blade wrap angles while keeping other parameters constant. The three-dimensional flow fields in three centrifugal pumps are numerically simulated, and the simulation results illustrate that the blade with larger wrap angle has more powerful control ability on the flow pattern in impeller. The three pumps have nearly the same pressure distributions at the small flow rate, but the pressure gradient increase in the pump with the largest wrap angle is smoother than the other two pumps at the design and large flow rates. The pump head and efficiency are also influenced by the blade wrap angle. The highest head and efficiency are also observed for the largest angle. An experiment rig is designed and built to test the performance of the pump with the largest wrap angle. The test results show that the wide space of its efficiency area and the stability of its operation ensure the excellent performance of the design method and verify the numerical analysis. The analysis on influence of the blade wrap angle for centrifugal pump performance in this paper can be beneficial to the optimization design of the centrifugal pump.

Research on seismic performance of shear walls with concrete filled steel tube columns and concealed steel trusses

In order to further improve the seismic performance of RC shear walls, a new composite shear wall with concrete filled steel tube （CFT） columns and concealed steel trusses is proposed. This new shear wall is a double composite shear wall; the first composite being the use of three different force systems, CFT, steel truss and shear wall, and the second the use of two different materials, steel and concrete. Three 1/5 scaled experimental specimens： a traditional RC shear wall, a shear wall with CFT columns, and a shear wall with CFT columns and concealed steel trusses, were tested under cyclic loading and the seismic performance indices of the shear walls were comparatively analyzed. Based on the data from these experiments, a thorough elastic-plastic finite element analysis and parametric analysis of the new shear walls were carried out using ABAQUS software. The finite element results of deformation, stress distribution, and the evolution of cracks in each phase were compared with the experimental results and showed good agreement. A mechanical model was also established for calculating the load-carrying capacity of the new composite shear walls. The results show that this new type of shear wall has improved seismic performance over the other two types of shear wails tested.

Numerical and Experimental Studies on the Effect of Axial Spacing on Hydrodynamic Performance of the Hybrid CRP Pod Propulsion System

The hydrodynamic performance of a hybrid CRP pod propulsion system was studied by RANS method with SST k ？？ turbulence model and sliding mesh. The effect of axial spacing on the hydrodynamic performance of the hybrid CRP pod propulsion system was investigated numerically and experimentally. It shows that RANS with the sliding mesh method and SST k -ω turbulence model predicts accurately the hydrodynamic performance of the hybrid CRP pod propulsion system. The axial spacing has little influence on the hydrodynamic performance of the forward propeller, but great influence on that of the pod unit. Thrust coefficient of the pod unit declines with the increase of the axial spacing, but the trend becomes weaker, and the decreasing amplitude at the lower advance coefficient is larger than that at the higher advance coefficient. The thrust coefficient and open water efficiency of the hybrid CRP pod propulsion system decrease with the increase of the axial spacing, while the torque coefficient keeps almost constant. On this basis, the design principle of axial spacing of the hybrid CRP pod propulsion system was proposed.

Future Performance Prediction of Research Infrastructure Based on Past Performance

Research infrastructure is crucial for development of research,and thus the evaluation of its performance is important.However,existing researches mostly focus on its past observations,lacking of a prediction for future. In this paper, procedures are proposed to predict the distribution for the number of papers published in a certain future year. The publication reliability,which is defined as the probability that the number of published papers in the future year is bigger than a pre-specified number,is evaluated. Illustrative examples are proposed to show the applications of the model.

Experimental Study on the Hydrodynamic Performance of a Heaving Buoy Assembled on a Net Cage Platform

To take advantage of the abundance of both fishery and wave energy resources in offshore sea areas,a novel floating platform with a heaving buoy-based wave energy converter(WEC)assembled with a set of net cages is presented in this work.The floating WEC system provides a power supply,while the net cages are used for aquaculture.It is designed to have an independent and self-operation breeding function.An experimental study is carried out to investigate the hydrodynamic performance of the device in a wave tank considering the factors of net cages,draft depth,and power take-off,and results show that these variables have significant effects on wave energy capture.Incident waves with short periods cause intense interactions that allow the device to undergo large relative motion.The draft depth could be determined according to wave period rather than wave height.This study also explores the response amplitude operator of the device and determines its resonance scope.The experimental results could provide reliable information for future studies on phase differences and the design of two-body WECs.

Preparation and Performance Research of Cement-based Grouting Materials with High Early Strength and Expansion

Main performance of the cement grouting materials made up by Portland cement（PC） and sulphoaluminate cement（SAC） was investigated in this program, a kind of expanding agent（EA） which was mainly constituted by metakaolin and alunite was utilized for the compensation of the shrinkage, the hydration products and micro structure of the grouting materials were researched by X-ray diffraction（XRD） and scanning electron microscopy（SEM）. The results showed that a high expansion rate of the grouting materials could be reached as the expanding agent mixed in 6% of PC mass; the addition of SAC in the S2（PC：SAC：EA=34：6：2.25） brought a further improvement of the expansion rate of the grouting materials, the analysis of XRD and SEM showed that due to the reaction of expanding agent and SAC in the grouting materials, more ettringite crystal was generated, which resulted in a higher early strength, the addition of SAC played an expansion and strength reinforcement role in the grouting materials.

Experimental study on the working performance of different milling tools for multistage fracturing ball seats

To achieve the secondary production in multistage fracturing wells of tight oil,milling tools are usually used to remove the multistage fracturing ball seats to achieve production with a large diameter in later.In this paper,first of all,the working mechanism of milling tools for multistage fracturing ball seats was studied and a mechanical analysis model of single abrasive grain was established.Then,an experimental system for milling tools was developed,and the experimental tests of the flat,the blade,and the slope milling tool were conducted in order.Besides,the morphology of chips and the surface morphology of the workpiece after the experiment were analyzed.Also,the working performance of milling tools was evaluated from the perspectives of working safety,working efficiency,and wear resistance of the milling tool.The results show that the torque of the milling tool increases nonlinearly with the increase in the cutting depth of the abrasive grain and increases linearly with the increase in the cutting width.Also,the chips are irregular particles and the size is mainly from 10 to 50μm.So,the chips should be pumped up with a small pump pressure and a large displacement.Besides this,the cutting depths of the abrasive grains are from 216.20 to 635.47μm and the bottom surface of the milling tool should be eccentric to avoid the zero point of cutting speed.Furthermore,the torque of the slope milling tool is 23.8%larger than that of the flat milling tool,which is also 30.4%smaller than that of the blade milling tool.Compared with the flat milling tool,the working efficiency of the blade milling tool improves by 79.9%and the slope milling tool improves by 111.1%.Also,the wear resistance of the blade milling tool decreases by 102.7%,while the slope milling tool declines by 32.6%when compared with the flat milling tool.Therefore,the slope milling tool has the characteristics of moderate torque,stable working conditions,the highest working efficiency,and fine wear resistance,which is preferably used to mill multistage fracturing ball seats.This study provides a theoretical basis and guidance for milling multistage fracturing ball seats on-site and realizing production with a large diameter in later stages of multistage fracturing wells.

An Experimental Study on the Effect of the Side Hull Symmetry on the Resistance Performance of a Wave‑Piercing Trimaran

This paper presented the results of an experimental investigation into the resistance performance of a wave-piercing trimaran with three alternative side hull forms,including asymmetric inboard,asymmetric outboard,and symmetric at various stagger/separation positions.Model tests were carried out at the National Iranian Marine Laboratory(NIMALA)towing tank using a scale model of a trimaran at the Froude numbers from 0.225 to 0.60.Results showed that by moving the side hulls to the forward of the main hull transom,the total resistance coefficient of trimaran decreased.Findings,furthermore,demonstrated that the symmetry shape of the side hull had the best performance on total resistance among three side hull forms.Results of this study are useful for selecting the side hull configuration from the resistance viewpoint.

Research Advances in Detection Techniques of High Performance Liquid Chromatography-Refractive Index Detector

As a highly sensitive and stable detector,refractive index detector is usually used for quantitative detection of substances such as polymer,sugar and organic acid. The research reviewed the application of HPLC-RID in the fields of quantitative determination of medicine and food,in order to lay a foundation for wider use of RID.

Experimental Study on Wave Attenuation Performance of A New Type of Floating Breakwater with Twin Pontoons and Multi Porous Vertical Plates

A floating breakwater(FB)has extensive potential applications in the fields of coastal,offshore,and ocean engineering owing to its advantages such as eco-friendliness,low cost,easy and rapid construction,and quick dismantling and reinstallation.An FB composed of twin pontoons and multi-porous vertical plates is proposed to improve the wave attenuation performance.The wave attenuation performance is investigated for different FB structures and vertical plate types under different incident wave heights and periods using 2D wave physical model tests in a wave flume.The results demonstrate that the proposed FB has a better performance than that of the conventional single pontoon-type FB.It reduces the wave transmission due to its enhanced wave reflection and energy loss.The wave transmission coefficient of the proposed FB decreases with an increase in the number of layers and relative draft depth of the vertical plates.However,a further decrease in the wave transmission coefficient is not observed when the number of porous vertical plates is increased from 4 to 5 layers.An equation has been derived to predict the wave transmission of the proposed FB based on the experimental results.

Calculated and Experimental Research of Sheet Resistances of Laser-Doped Silicon Solar Cells

The calculated and experimental research of sheet resistances of crystalline silicon solar cells by dry laser doping is investigated. The nonlinear numerical model on laser melting of crystalline silicon and liquid-phase diffusion of phosphorus atoms by dry laser doping is analyzed by the finite difference method implemented in MATLAB. The melting period and melting depth of crystalline silicon as a function of laser energy density is achieved. The effective liquid-phase diffusion of phosphorus atoms in melting silicon by dry laser doping is confirmed by the rapid decrease of sheet resistances in experimental measurement. The plateau of sheet resistances is reached at around 15 Ω/. The calculated sheet resistances as a function of laser energy density is obtained and the calculated results are in good agreement with the corresponding experimental measurement. Due to the successful verification by comparison between experimental measurement and calculated results, the simulation results could be used to optimize the virtual laser doping parameters.

Research on Financial Performance of State-owned Enterprise Mixed Ownership Reform

Mixed ownership is an important form of realization of China＇s economic system reform and development, and it is also the main direction of state-owned enterprise reform. In order to further promote the deepening of the reform of mixed ownership, this paper randomly selects 200 listed state-owned enterprises as research objects, and studies the trends of the financial performance of these enterprises from the mixed state-owned enterprises and non-mixed-modification enterprises in the five years from 2013 to 2017, and compares their various trends. Financial indicators, a comprehensive evaluation of the problems and causes in the reform of the mixed ownership system, and then propose countermeasures to further deepen the reform of mixed ownership based on the research conclusions.

Biomimetic Experimental Research on Hexapod Robot's Locomotion Planning

To provide hexapod robots with strategies of locomotion planning, observation experiments were operated on a kind of ant with the use of high speed digital photography and computer assistant analysis. Through digitalization of original analog video, locomotion characters of ants were obtained, the biomimetic foundation was laid for polynomial trajectory planning of multi-legged robots, which was deduced with mathematics method. In addition, five rules were concluded, which apply to hexapod robots marching locomotion planning. The first one is the fundamental strategy of multi-legged robots＇ leg trajectory planning. The second one helps to enhance the static and dynamic stability of multi-legged robots. The third one can improve the validity and feasibility of legs＇ falling points. The last two give criterions of multi-legged robots＇ toe trajectory figures and practical recommendatory constraints. These five rules give a good method for marching locomotion planning of multi-legged robots, and can be expended to turning planning and any other special locomotion.

The Flemish Performance-based Research Funding System: A Unique Variant of the Norwegian Model

The BOF-key is the performance-based research funding system that is used in Flanders, Belgium. In this paper we describe the historical background of the system, its current design and organization, as well as its effects on the Flemish higher education landscape. The BOFkey in its current form relies on three bibliometric parameters: publications in Web of Science, citations in Web of Science, and publications in a comprehensive regional database for SSH publications. Taken together, the BOF-key forms a unique variant of the Norwegian model: while the system to a large extent relies on a commercial database, it avoids the problem of inadequate coverage of the SSH. Because the bibliometric parameters of the BOF-key are reused in other funding allocation schemes, their overall importance to the Flemish universities is substantial.

Substantiality:A Construct Indicating Research Excellence to Measure University Research Performance

Purpose:The adequacy of research performance of universities or research institutes have often been evaluated and understood in two axes:“quantity”(i.e.size or volume)and“quality”(i.e.what we define here as a measure of excellence that is considered theoretically independent of size or volume,such as clarity in diamond grading).The purpose of this article is,however,to introduce a third construct named“substantiality”(“ATSUMI”in Japanese)of research performance and to demonstrate its importance in evaluating/understanding research universities.Design/methodology/approach:We take a two-step approach to demonstrate the effectiveness of the proposed construct by showing that(1)some characteristics of research universities are not well captured by the conventional constructs(“quantity”and“quality”)-based indicators,and(2)the“substantiality”indicators can capture them.Furthermore,by suggesting that“substantiality”indicators appear linked to the reputation that appeared in university reputation rankings by simple statistical analysis,we reveal additional benefits of the construct.Findings:We propose a new construct named“substantiality”for measuring research performance.We show that indicators based on“substantiality”can capture important characteristics of research institutes.“Substantiality”indicators demonstrate their“predictive powers”on research reputation.Research limitations:The concept of“substantiality”originated from IGO game;therefore the ease/difficulty of accepting the concept is culturally dependent.In other words,while it is easily accepted by people from Japan and other East Asian countries and regions,it might be difficult for researchers from other cultural regions to accept it.Practical implications:There is no simple solution to the challenge of evaluating research universities’research performance.It is vital to combine different types of indicators to understand the excellence of research institutes.Substantiality indicators could be part of such a combination of indicators.Originality/value:The authors propose a new construct named substantiality for measuring research performance.They show that indicators based on this construct can capture the important characteristics of research institutes.

Research Performance Assessment Based on T-Indicator

A novel indicator named after Tianjin University (TJU)-T-indicator-was investigated as an effective supplement of established Article Assessment System of Tianjin University, aiming to correct differences among fields. Based on normalized citation counts, T-indicator could give the order of research performance of researchers or groups in different disciplines. Weighted citation analysis was also introduced in this method to judge the contribution of researchers to their research outcomes. A given example was used to thoroughly discuss this evaluation method, via the application of derivative indices, including Tyear, Taverage, Ttotal and weighted-Ttotal.

National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology

Founded in 2012,the National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology at Jinan University,one of the'211'key national universities in China,specializes in the research and development of iron based wear resistant materials and their casting technologies to provide support to the production process.The Research Center serves the'Guangdong Province Ceeusro Innovation Platform for Common Technology of High Performance Wear Resistant Materials”,“Guangdong Province Engineering Research Center for Wear Resistant and Special Functional Materials”.