Effect of Li on formation of long period stacking ordered phases and mechanical properties of Mg-Gd-Zn alloy

Alloys with composition of Mg_(96-x)Gd_3Zn_1Li_x(at.%)(x=0, 2, 4, and 6) were prepared by conventional casting. The microstructures of these alloys under as-cast and solid-solution conditions have been observed, and the mechanical properties were investigated. The results showed that Li is an effective element to refine the grains and break the eutectic networks in as-cast MgGd_3Zn_1 alloy. During solid solution treatment, these broken eutectic networks are spheroidized and highly dispersed. In addition, plentiful lamellar long period stacking ordered(LPSO) phases are precipitated in an α-Mg matrix when the Li addition is not more than 4%. Solid-solution treated Mg_(92)Gd_3Zn_1Li_4 alloy exhibits an optimal ultimate tensile strength(UTS) of 226 MPa and elongation of 5.8%. The strength of MgGd_3Zn_1 alloy is improved significantly, meanwhile, the toughness is apparently increased.

Effect of long period stacking ordered phase on damping capacities of as-cast Mg-Zn-Y alloys

The microstructure and damping capacities of MgZnxYi.33x(x=l-4at.%)alloys were discussed and researched.The main phase composition of the alloys consists of a_Mg and long-period stacking ordered(LPSO)phase.Due to increasedLPSO phase,grain size was refined.LPSO phase was advantageous to the damping properties of the Mg-Zn-Y alloys.Mg-7%Zn-12.8%Y has the highest damping capacity up to0.04.Due to stacking fault probability,the LPSO phase in the Mg-Zn-Yalloys could be new damping source to dissipate energy so as to contribute to the improvement of damping capacities.

Analysis of period and visibility of dual phase grating interferometer

Dual phase grating interferometer may simultaneously achieve large field of view and high x-ray dose efficiency.Here,we develop a simple theoretical method to better understand the imaging process of the dual phase grating interferometer.The derivation process of fringe period and the optimal visibility conditions of the dual phase grating interferometer are given in detail.Then,we theoretically prove that the fringe period and optimal visibility conditions of the dual phase grating interferometer include that of the Talbot interferometer.By comparing our experimental results with those of other researchers,we find that when the positions of phase gratings are far away from the positions where the fringe visibility is optimal,the fringe period of the dualπ-phase grating interferometer is twice the theoretical results under the illumination of polychromatic x-ray.This conclusion may explain the contradictory research results of dual phase grating interferometer among different researchers.

Microstructure and mechanical properties of a compound reinforced Mg95Y2.5Zn2.5 alloy with long period stacking ordered phase and W phase

The microstructure evolution of Mg100-2xYxZnx （x=2, 2.5, 3, 3.5） alloys was investigated. Results show that the Mg100-2xYxZnx alloys are composed of a-Mg, long period stacking ordered （LPSO） phase and eutectic structure phase （W phase）, and the Mg95Y2.5Zn2.5 alloy has the best comprehensive mechanical properties. Subsequently, the microstructure evolution of the optimized alloy Mg95Y2.5Zn2.5 during solidification and heat treatment processes was analyzed and discussed by means of OM, SEM, TEM, XRD and DTA. After heat treatment, the lamellar phase 14H-LPSO precipitated in a-Mg and W phase transforms into particle phase （MgyZn2）. Due to the compound reinforcement effect of the particle phase and LPSO phase （18R＋14H）, the mechanical properties of the alloy are enhanced. The tensile strength and elongation of the Mg95Y2.5Zn2.5 alloy is improved by 9.1% and 31.3% to 215 MPa and 10.5%, respectively, after solid-solution treatment.

Dilute long period stacking/order(LPSO)-variant phases along the composition gradient in a Mg-Ho-Cu alloy

We have systematically investigated the microstructures of as-cast Mg_(97.49)Ho_(1.99)Cu_(0.43)Zr_(0.09)alloy by atomic resolution high-angle annular dark field scanning transmission electron microscopy(HAADF-STEM), revealing the coexistence of 18R, 14H and 24R long period stacking/order(LPSO) phases with fully coherent interfaces along step-like composition gradient in a blocky intermetallic compound distributed at grain boundary. The short-range order(SRO) L1_(2)-type Cu_(6)Ho_(8)clusters embedded across AB’C’A-stacking fault layers are directly revealed at atomic scale. Importantly, the order degree of SRO clusters in the present dilute alloy is significant lower than previous 6M and 7M in-plane order reported in ternary Mg-TM(transition metal)-RE(rare earth) alloys, which can be well matched by 9M in-plane order. This directly demonstrates that SRO in-plane L1_(2)-type clusters can be expanded into more dilute composition regions bounded along the definite TM/RE ratio of 3/4. In addition, the estimated chemical compositions of solute enriched stacking fault(SESF) in all LPSO variants are almost identical with the ideal SESF composition of 9M in-plane order, regardless of the type of LPSO phases. The results further support the viewpoint that robust L1_(2)-type TM_(6)RE_(8)clusters play an important role in governing LPSO phase formation.

Topological phase transition in cavity optomechanical system with periodical modulation

We investigate the topological phase transition and the enhanced topological effect in a cavity optomechanical system with periodical modulation.By calculating the steady-state equations of the system,the steady-state conditions of cavity fields and the restricted conditions of effective optomechanical couplings are demonstrated.It is found that the cavity optomechanical system can be modulated to different topological Su–Schrieffer–Heeger(SSH)phases via designing the optomechanical couplings legitimately.Meanwhile,combining the effective optomechanical couplings and the probability distributions of gap states,we reveal the topological phase transition between trivial SSH phase and nontrivial SSH phase via adjusting the decay rates of cavity fields.Moreover,we find that the enhanced topological effect of gap states can be achieved by enlarging the size of system and adjusting the decay rates of cavity fields.

Floquet dynamical quantum phase transitions in transverse XY spin chains under periodic kickings

Floquet dynamical quantum phase transitions(DQPTs),which are nonanalytic phenomena recuring periodically in time-periodic driven quantum many-body systems,have been widely studied in recent years.In this article,the Floquet DQPTs in transverse XY spin chains under the modulation ofδ-function periodic kickings are investigated.We analytically solve the system,and by considering the eigenstate as well as the ground state as the initial state of the Floquet dynamics,we study the corresponding multiple Floquet DQPTs emerged in the micromotion with different kicking moments.The rate function of return amplitude,the Pancharatnam geometric phase and the dynamical topological order parameter are calculated,which consistently verify the emergence of Floquet DQPTs in the system.

Stability in Liquid Phases of Molecular Compounds Composed of Saturated Atoms: Application with the Even-Odd Rule and a Specific Periodic Table for Liquids

Building on the idea that molecules in liquid phase associate into multi-molecular complexes through covalent bonds, the present article focuses on the possible structures of these complexes. Saturation at atomic level is a key concept to understand where connections occur and how far molecules aggregate. A periodic table for liquids with saturation levels is proposed, in agreement with the even-odd rule, for both organic and inorganic elements. With the aim at reaching the most stable complexes, meaning no other chemical reactions can occur in the liquid phase, the structure of complexes resulting from liquefaction of about 30 molecules is devised. The article concludes that complexes in liquids generally assume rounded shapes of an intermediate size between gas and solid structures. It shows that saturation and covalent bonds alone can explain the specific properties of liquids. While it is generally acknowledged that molecular energy in gases and solids are respectively linear kinetic and vibratory, we suggest that rotatory energy dominates in liquids.

CRYSTAL STRUCTURE OF A LONG－PERIOD ORDERED PHASE IN Fe－C MARTENSITE AND COMPUTER SIMULATION OF ITS ELECTRON DIFFRACTION PATTERNS

Different structure models of a long-period ordered phase in Fe-C martenstie formed during aging have been checked by computer simulation of electron diffraction(ED) patterns based on these models.The results showed that the simulated ED pattern of γ'-FexC(Ⅱ) model proposed by the present authors is in good agreement with experimentally observed ED pattern.It was also confirmed that the incommensurate superperiod stems from the coexistence of several γ'-Fe_xC(H) phases with different superperiods.The Fe(144)C(24)(Fe6C) model proposed by Uwakweh et al.generated ED patterns remarkably different from the experimental ones.

Nanomechanics of Mg-Gd-Y-Nd-Zn alloy with LPSO and MgRE phases

The mechanical properties of two main precipitating phases(LPSO and MgRE)and matrix in Mg-Gd-Y-Nd-Zn bioalloy were examined using nanoindentation method.A new is suggested for characterizing the elastic-plastic behavior,fracture toughness and strain rate sensitivity(SRS)of materials within micro/nanoscale.Firstly,a nanomechanical model was developed for extracting hardness(H),young’s modulus(E)and yield stress(σY)from the characteristic load points which were subsequently analyzed by atomic force microscope(AFM)images.The elasticity data and AFM data were then utilized for determination of plastic deformation in constituent phases.The displacement of the indentation gets the highest value for Mg matrix and between precipitates,depth is more in LPSO rather than that of MgRE.The serrated flow or the behavior of shear bands may originate from the side effect of the interface region in Mg alloys with precipitates.It can be deduced that the KIC produced by both L method and energy-based calculation are both reliable for KIC approximation.The maximum load in simulation withμ=0.2 friction is marginally lesser than that of the frictionless(μ=0)one while elastic recovery of indentation withμ=0.2 is higher to some extent.

Simulation of pre-precipitation in Ni_(75)Al_(14)Mo_(11) alloy by microscopic phase-field model

The early precipitation process of Ni（75）Al（14）Mo（11） alloy was simulated by microscopic phase-field model at different temperatures.The microstructure of the alloy,the precipitation time of Llo structure and occupation probability of the three kinds of atoms were investigated.It is indicated that the non-stoichiometric Ll0（Ⅰ/Ⅱ） phases are found in the precipitation process.With the temperature increasing,the appearance time of Ll0 is brought forward.The Ll0（Ⅱ） structure always precipitates earlier than the Ll0（Ⅰ） structure.Compared with lower temperature,higher temperature brings the formation time of Ll0 phase forward and makes Ll0 phase have a higher order degree.But lower temperature shortens the process time of the Ll0 phase to the Ll2 phase.Al and Mo atoms tend to occupy γ site,Ni atom tends to occupy a and β sites.At the same temperature,Al atom has stronger occupation ability than Mo atom in the same site.Ni,Al and Mo collectively form the composited Ll2 structure.

THREE- DIMENSIONAL PERIODICITY ANDTENFOLD ROTATIONAL SYMMETRY

Electron-diffraction pattern with 'tenfold rotational symmetry' of Al-Fe alloyphase is assumed to be produced by periodic structure. One 3D periodic structure is presentedbased on so-called C polyhedra. The structure can be used as atomic model to describethe Al-Fe alloy phase. The Fourier transform patterns of the model are in good agreementwith the corresponding electron-diffraction patterns. Several other models with' tenfold symmetry' Fourier transform patterns have briefly been mentioned.

Microstructure characterization and corrosion behavior of Mg-Y-Zn alloys with different long period stacking ordered structures

Mg-Y-Zn alloys with long period stacking ordered(LPSO)structure have received much attention recently and exhibit great potential in applications such as automotive,aerospace and in bio-medical fields.This paper aimed to investigate the effect of different phase constitution of LPSO structures on corrosion rate of bio-medical Mg-Y-Zn alloys.The results showed that as-cast Mg98.5Y1Zn0.5 alloys containing only 18R structure exhibited the highest corrosion resistance with the corrosion rate of 2.78 mm/year.The precipitation of 14H lamellas within a-Mg grains during solid solution treatment introduced the crystallographic orientation corrosion by accelerating micro-galvanic corrosion.The increase of 18R/14H interfaces deteriorated the corrosion resistance,and the grain boundaries also suffered from severe electrochemical dissolution.This work suggested that Mg-Y-Zn alloys with single LPSO structure(either 18R or 14H)exhibited better corrosion resistance than alloys with co-existence 18R and I4H LPSO structures.

Towards high strength cast Mg-RE based alloys:Phase diagrams and strengthening mechanisms

Mg-rare earth(RE)based systems provide several important commercial alloys and many alloy development opportunities for high strength applications,especially in aerospace and defense industries.The phase diagrams,microstructure,and strengthening mechanisms of these multicomponent systems are very complex and often not well understood in literature.We have calculated phase diagrams of important binary,ternary,and multicomponent RE-containing alloy systems,using CALPHAD(CALculation of PHAse Diagrams).Based on these phase diagrams,this paper offers a critical overview on phase equilibria and strengthening mechanisms in these alloy systems,including precipitation,long period stacking order(LPSO),and other intermetallic phases.This review also summarized several promising Mg-RE based cast alloys in comparison with commercial WE54 and WE43 alloys;and explored new strategies for future alloy development for high strength applications.It is pointed out that the combination of precipitation and LPSO phases can lead to superior strength and ductility in Mg-RE based cast alloys.The precipitates and LPSO phases can form a complex three-dimensional network that effectively impedes dislocation motion on the basal and non-basal planes.The LPSO phases can also prevent the coarsening of precipitates when they interact,thus providing good thermal stability at elevated temperatures.Future research is needed to determine how the combination of these two types of phases can be used in alloy design and industrial scale applications.

Research and application of regular phenomenon between periodic signals

The phase change between periodic signals is regular. Research on the regular phenomenon between periodic signals is helpful to improve the precision of some measurements and develop some new measurement methods. So it is necessary to analyze the characteristics of the greatest common factor frequency and the least common multiple period universally existing in periodic signals. The regulation of the quantitative phase shift resolution between periodic signals is presented.The cause of difference in phase characteristics between periodic signals is explained well. In this paper we propose different application prospects based on the regular phenomenon between periodic signals, with focusing on the methods for high precision frequency measurement and transient stability measurement. The experimental results are satisfactory.

Influence of periodic pressure on dendritic morphology and sidebranching

The influence of periodic pressure with low and high frequencies on microstructure and dendritic sidebranching was studied by using 3-D phase field method. In both low and high frequency cases, the variation trend of SDAS (secondary dendritic arm spacing) with increasing pressure frequency is opposite to that of sidebranching frequency, while the variation trend of the average length of secondary arms is consistent with that of sidebranching frequency. The high sidebranching frequency indicates that more secondary arms share the whole driving force of dendrite growth, resulting in lower driving force for each one and leading to less developed secondary arms. The smallest SDAS is obtained when perturbed by the periodic pressure with the frequency of 0.157/τ0 (τ0 is the physical unit of time in the dimensionless phase field model) and 2.200/τ0 in low and high frequency cases, respectively. Comparisons of dendritic morphology and secondary arms are made between the low and high frequency cases. Firstly, in the low frequency case, secondary arms are luxuriant especially when pressure frequency is low, with many high-order side branches stretching out. Secondly, the average length of secondary arms in primary dendrite is longer in the low frequency case than that without pressure, and much longer than that in the high frequency case. Thirdly, the dendrite tip without side branches in the high frequency case is much longer than that in the low frequency case. All of the differences in dendritic morphology and sidebranching in the two cases can be attributed to the different modulation mechanism. In the low frequency case, periodic pressure determines tip velocity and then modulates sidebranching directly. While in the high frequency case, periodic pressure cannot determine sidebranching directly, but via modulating tiny protuberances in dendrite tip, part of which evolves into side branch. In this case, the tiny protuberances take part of the whole driving force, leading to less developed secondary arms.

Experimental Research on Single-Pass SHG from Periodically Poled LiNbO_3 Crystal

Quasi phase matching (QPM) periodical poled LiNbO 3(PPLN) is designed and successfully fabricated to enable second harmonic generation(SHG).The samples were Z cut 0.5 mm thick and grating period is Λ=6.8 μm for the first order QPM of continual wave λ=1.064 μm which is emitted by Nd∶YAG laser at room temperature 27 ℃. The output single pass SHG power was tested by an authorized optical system. The normalized max conversion efficiency is calculated to be 0.25 0 0(W·cm) -1 .The fabrication and parameters calculated method are introduced, and testing scheme is described in this paper. Even some ideas to improve conversion efficiency are offered.

Interdecadal Variations of Phase Delays Between Two Nino Indices at Different Time Scales

Phase delays between two Nino indices-sea surface temperatures in Nino regions 1+2 and 3.4 (1950-2001)-at different time scales are detected by wavelet analysis. Analysis results show that there are two types of period bifurcations in the Nino indices and that period bifurcation points exist only in the region where the wavelet power is small. Interdecadal variation features of phase delays between the two indices vary with different time scales. In the periods of 40-72 months, the phase delay changes its sign in 1977: Nino 1+2 indices are 2-4 months earlier than Nino 3.4 indices before 1977, but 3-6 months later afterwards. In the periods of 20-40 months, however, the phase delay changes its sign in another way: Nino 1+2 indices are 1-4 months earlier before 1980 and during 1986-90, but 1-4 months later during 1980-83 and 1993-2001.