We present a simple hot press-based method for processing La(Fe,Si)13-based compounds consisting of La–Fe–Co–Si–C particles and phenolic resin. The magnetic entropy change △S per unit mass for the La Fe_(10.87)Co...We present a simple hot press-based method for processing La(Fe,Si)13-based compounds consisting of La–Fe–Co–Si–C particles and phenolic resin. The magnetic entropy change △S per unit mass for the La Fe_(10.87)Co_(0.63)Si_(1.5)C_(0.2)/phenolic resin compounds have nearly the same magnitude with the base materials. With the content of phenolic resin of 5.0 wt%, the compound conductivity is 3.13 W·m^(-1)·K^(-1). In order to measure the cooling performance of La(Fe,Si)13-based compounds,the La(Fe_(11.6-x)Co_(x))Si_(1.4)C_(0.15)(x =0.60, 0.65, 0.75, 0.80, 0.85)/phenolic resin compounds were pressed into thin plates and tested in a hybrid refrigerator that combines the active magnetic refrigeration effect with the Stirling cycle refrigeration effect. The test results showed that a maximum cooling power of 41 W was achieved over a temperature span of 30 K.展开更多
The study characterized the curing behaviors of phenol formaldehyde(PF)resin under different vacuum degrees and explored the properties of 9-ply plywood panels hot-pressed under both vacuum and atmospheric conditions....The study characterized the curing behaviors of phenol formaldehyde(PF)resin under different vacuum degrees and explored the properties of 9-ply plywood panels hot-pressed under both vacuum and atmospheric conditions.The changes in core temperature and moisture content of the plywood mats during hot pressing were investigated as well.It was found that the gel times and gel temperatures of PF resin decreased with the increase of vacuum degree using a self-made device.FTIR spectra indicated the degree of polycondensation of hydroxymethyl gradu-ally increased with the increase in temperature.It was also observed that a higher degree of vacuum led to a slower polycondensation reaction rate of PF resin.During different hot-pressing processes,the bonding strengths in the innermost and uppermost gluelines of the vacuum hot-pressed plywood panels were up to 30%–50%higher than their counterparts of conventional hot-pressed products.A less difference in the bonding strengths between these two gluelines was also observed for vacuum hot-pressed products.In addition,the core of vacuum hot-pressed plywood was found to have a greater heating rate and higher temperature at thefinal stage of hot pressing,which was beneficial to cure the PF resin.The results from this study indicate a promising potential of introducing a vacuum during hot pressing to improve the quality and productivity of plywood products and provide a basis for adopting vacuum to hot press wood composites.展开更多
Benzoxazine resin,being a new type of phenolic resin deve-loped to overcome the shortcomings of traditional phenolic resins,has been synthesized from phenol,formaldehyde and amine,and does not require solvent eliminat...Benzoxazine resin,being a new type of phenolic resin deve-loped to overcome the shortcomings of traditional phenolic resins,has been synthesized from phenol,formaldehyde and amine,and does not require solvent elimination or monomer purification to obtain a relatively clean precursor.It has potential application in the field of aerospace due to its low expansion coefficient,high weather resistance,high carbon yield,good mechanical strength,and excellent ablation resistance[1].It can be mixed with various other resins or polymers to produce new resins with a broad range of applications[2-3].展开更多
In-situ reactive compatibilization of high-density polyethylene (HDPE)/ground tire rubber (GTR) blends by dicumyl peroxide (DCP) and HY-2045 - a kind of thermoplastic phenolic resin without catalyst was inves...In-situ reactive compatibilization of high-density polyethylene (HDPE)/ground tire rubber (GTR) blends by dicumyl peroxide (DCP) and HY-2045 - a kind of thermoplastic phenolic resin without catalyst was investigated by studying the mor-phology, stress and strain behavior, dynamic mechanical properties and crystallization performance of the blends. Scanning e-lectron microscopy (SEM) results show that there are a lot of fibrous materials distributing in the interface, which connects the dispersed phase with the matrix and obtains better interfacial strength for prominent mechanical properties. The addition of compatibilizers results in the decrease of crystallinity of the blends and the disappearance of an obvious yield phenomenon, which was proved by the differential scanning calorimeter (DSC) test and X-ray diffraction (XRD) characterization Although the crystallinity of the blends decreases,the tensile strength and tensile strain of the blends significantly increases, especially for the HDPE/GTR/DCP/HY-2045 blends, which is possibly attributed to the good compatibility of the blends owing to the in-situ interface crosslinking. In addition, it is found that the compatibilizing HDPE/GTR blends shows a higher tan^ peak temperature and a broaden transition peak for GTR phase.展开更多
Phenolic resin/montmorillonite intercalation composites were prepared by using the methods of pressing intercalation and melt intercalation.Properties and structure of the composites were investigated by using XRD,TG ...Phenolic resin/montmorillonite intercalation composites were prepared by using the methods of pressing intercalation and melt intercalation.Properties and structure of the composites were investigated by using XRD,TG and test of softening point.It is indicated that both the pressing intercalation and melt intercalation can be used to prepare the phenolic resin/organo-montmorillonite intercalation nanocomposites.Compared with phenolic resin,the intercalation nanocomposites have better heat-resistance,higher decomposition temperatures and less thermal weight-loss.However,these two intercalation methods have different effects on the softening point of the intercalation nanocomposites.Pressing intercalation almost does not affect the softening point of the intercalation nanocomposites,while melt intercalation significantly increases the softening point of the intercalation nanocomposites, probably due to the chemical actions happening in the process of melt intercalation.展开更多
A novel benzoxazine-based phenolic resin containing furan groups(PFB) was synthesized via simple two-step reactions and the structure of PFB was confirmed by FTIR and ~1H NMR spectra.Differential scanning calorimetr...A novel benzoxazine-based phenolic resin containing furan groups(PFB) was synthesized via simple two-step reactions and the structure of PFB was confirmed by FTIR and ~1H NMR spectra.Differential scanning calorimetry(DSC) showed that the polybenzoxazine cured from PFB had good heat resistance and lower polymerization temperature compared with that of benzoxazine-based phenolic resins.展开更多
The dynamic mechanical properties of a new blend system consisting of phenol resin and polar polymer (acrylaterubber and/or chlorinated polypropylene) were investigated. It was found that the addition of phenol resin ...The dynamic mechanical properties of a new blend system consisting of phenol resin and polar polymer (acrylaterubber and/or chlorinated polypropylene) were investigated. It was found that the addition of phenol resin to acrylate rubberand its incompatible blend can cause a remarkable improvement in the temperature dependence of the loss tangent. As a result, the present blends are very good damping materials.展开更多
Mesocarbon microbeads (MCMB) were prepared from coal tar pitch modified by phenolic resin and from the same pitch modified by phenolic resin and hexamethylenetetramine at 440℃ for lh. By investigating the morpholog...Mesocarbon microbeads (MCMB) were prepared from coal tar pitch modified by phenolic resin and from the same pitch modified by phenolic resin and hexamethylenetetramine at 440℃ for lh. By investigating the morphology of mesophase spheres and the structure of the MCMB carbonized at 1000℃ for lh using scanning electron microscope (SEM) and XRD, it was found that phenolic resin accelerated the formation and coalescence of mesophase spheres. Some of the obtained MCMB were hi- or tri-spheres with the distorted microtextural carbon layers. Hexamethylenetetramine in the pitch modified by phenolic resin accelerated the condensation of phenolic resin and consequently expedited the combination of mesophase spheres, which was proved by the formation of some tetra-spheres. Owing to the cross-linkage of the additives, MCMB with complex structure were obtained.展开更多
Nanosized tungsten carbide was synthesized from phenol formaldehyde resin (PF) coated tungsten precursors. The process has three steps in which nanosized tungsten particles were first coated with PF, then the precur...Nanosized tungsten carbide was synthesized from phenol formaldehyde resin (PF) coated tungsten precursors. The process has three steps in which nanosized tungsten particles were first coated with PF, then the precursors were carburized at 950℃, and finally the carburized powders were treated in flowing wet hydrogen atmosphere at 940℃ to remove the uncombined carbon. The obtained powders were characterized using X-ray diffraction analysis (XRD), field-emission scanning electron microscopy (FESEM), small angle X-ray scattering (SAXS), and combustion-gas-volume method. The results indicated that single-phase WC could be synthesized using excessive PF as carburizer at a much lower temperature compared with using mixed carbon black. After wet hydrogen treating, the mean size of the obtained WC particles was 94.5 nm and the total carbon content was 6.18 wt.%.展开更多
This paper presents experimental observations on the adsorption of individual solutes by a simple thermodynamic framework, and the equilibrium adsorption of ethyl benzoate and diethyl phthalate on phenolic resin adsor...This paper presents experimental observations on the adsorption of individual solutes by a simple thermodynamic framework, and the equilibrium adsorption of ethyl benzoate and diethyl phthalate on phenolic resin adsorbent in hexane solutions within the temperature range of 293-313 K. The experimental results show that the Freundlich adsorption law is applicable to the adsorption of ethyl benzoate and diethyl phthalate on the adsorbent, since all the correlative factors R' are larger than 0.99. The negative values of all the isosteric adsorption enthalpies for ethyl benzoate and diethyl phthalate indicate that they undergo exothermic processes, while their magnitudes (19-28 kJ/mol) manifest a hydrogen bonding sorption process. Other thermodynamic properties: the free energy changes and the entropy change associated with the adsorption have been calculated from the Gibbs adsorption equation and the Gibbs-Helmholtz equation展开更多
A novel epoxidized soybean oil-toughened-phenolic resin(ESO-T-PR)has been synthesized by etheri- fication graft and multi-amine curing ESO.Fourier transform infrared spectroscopy(FTIR)was adopted to investi- gate its ...A novel epoxidized soybean oil-toughened-phenolic resin(ESO-T-PR)has been synthesized by etheri- fication graft and multi-amine curing ESO.Fourier transform infrared spectroscopy(FTIR)was adopted to investi- gate its molecular structure and scan electron microscope(SEM)was used to observe the micro morphology of its impact fracture surface.This ESO-T-PR was adopted as the matrix resin to prepare paper copper clad laminate (P-CCL)and the properties of resulting P-CCL are found superior to the related Chinese National Standard.The toughing mechanism was investigated by comparing the impact strength,solderleaching resistance,flexural strength, peeling strength and morphology of this ESO-T-PR with those of other two ESO modified phenolic resins.It is demonstrated that during the synthesizing process of ESO-T-PR,the phenol hydroxyl is etherified by ESO or ESO epoxy resin prepolymer(ESO chain extension polymer)and the long ESO epoxy resin chain segments enhance the crosslink density of ESO-T-PR and consequently improve the impact toughness and solderleaching resistance of P-CCL made of ESO-T-PR.The ESO-T-PR is a cheap matrix resin with excellent properties to make P-CCL(elec- tric guide board).展开更多
Wood of Chinese fir and poplar were liquefied in phenol at 150℃ and atmospheric pressure. The liquefied wood were reacted with formaldehyde to synthesize the liquefied wood-based resin. The factors affecting the resi...Wood of Chinese fir and poplar were liquefied in phenol at 150℃ and atmospheric pressure. The liquefied wood were reacted with formaldehyde to synthesize the liquefied wood-based resin. The factors affecting the resinification and the properties of new resin were investigated. The results show that the formaldehyde/liquefied wood molar ratio, reaction temperature, reaction time and sodium hydroxide/liquefied wood molar ratio have important influence on the resin characteristics. With the increase of formaldehyde/liquefied wood molar ratio, the yield of resin increases, and the flee phenol content of resins decreases, showing that the resinification of liquefied wood is more complete at higher formaldehyde/liquefied wood molar ratios. The reaction temperature on the viscosity of the liquefied resin has considerable effect; the viscosity of resin increased with increasing reaction temperature, and the amount of liquefied poplar resin increased more quickly than that of liquefied Chinese fir resin. The resinification time also has obvious influence on the viscosity of resin; the viscosity of liquefied poplar resin is more sensitive to resinification time compared with that of liquefied Chinese fir. The amount of sodium hydroxide can improve the water miscibility of liquefied wood resin. The optimum sodium hydroxide/liquefied wood molar ratio for preparation of liquefied wood-based resins exceeds 0.4.展开更多
New water soluble and photocrosslinkable prepolymers containing acrylate and quaternary ammonium salt groups were synthesized from epoxy phenolic resin via ring-opening reaction with acrylic acid and with aqueous solu...New water soluble and photocrosslinkable prepolymers containing acrylate and quaternary ammonium salt groups were synthesized from epoxy phenolic resin via ring-opening reaction with acrylic acid and with aqueous solution of triethylamine hydrochloride successively. The second reaction needs no phase transfer catalyst to accelerate, since the product formed can act as a phase transfer catalyst. The prepolymer obtained contains both photocrosslinkable acrylate groups and hydrophilic quaternary ammonium salt groups. Optimum conditions for these reactions were studied. The photosensitivity of the prepolymer was also investigated. The effects of different photoinitiators, different crosslinkable diluent monomers and amine accelerator on the photosensitivity of the prepolymer were compared. The photoinitiator of hydrogen abstraction type is still effective without using amine or alcohol as accelerator, because the prepolymer contains a H beside the OH groups formed in the ring-opening reactions.展开更多
To study the curing mechanism of alkaline phenolic resin with organic ester, three esters were chosen to react with three systems - alkaline phenolic resin, potassium hydroxide aqueous solution containing phenol, and ...To study the curing mechanism of alkaline phenolic resin with organic ester, three esters were chosen to react with three systems - alkaline phenolic resin, potassium hydroxide aqueous solution containing phenol, and potassium hydroxide aqueous solution. The variations of pH, heat release and gel pH during the reactions were monitored and measured. Infrared spectroscopy (IR) and thermal gravity analysis (TG) techniques were used to characterize the curing reaction. It was found that organic ester is only partial y hydrolyzed and resin can be cured through organic ester hydrolysis process as wel as the reaction with redundant organic ester. The sequential curing mechanism of alkaline phenolic resin cured by organic ester was identified as fol ows: a portion of organic ester is firstly hydrolyzed owing to the effect of the strong alkaline; the gel is then formed after the pH decreases to about 10.8-10.88, meanwhile, the redundant organic ester (i.e. non-hydrolysis ester) starts the curing reaction with the resin. It has also been found that the curing rate depends on the hydrolysis velocity of organic ester. The faster the hydrolysis speed of the ester, the faster the curing rate of the resin.展开更多
Five organic esters with different curing speeds:propylene carbonate(i.e.high-speed ester A);1,4-butyrolactone;glycerol triacetate(i.e.medium-speed ester B);glycerol diacetate;dibasic ester(DBE)(i.e.lowspeed ester C),...Five organic esters with different curing speeds:propylene carbonate(i.e.high-speed ester A);1,4-butyrolactone;glycerol triacetate(i.e.medium-speed ester B);glycerol diacetate;dibasic ester(DBE)(i.e.lowspeed ester C),were chosen to react with alkaline phenolic resin to analyze the application conditions of ester cured alkaline phenolic resin.The relationships between the curing performances of the resin(including pH value,gel pH value,gel time of resin solution,heat release rate of the curing reaction and tensile strength of the resin sand)and the amount of added organic ester and curing temperature were investigated.The results indicated the following:(1)The optimal added amount of organic ester should be 25 wt.%-30 wt.%of alkaline phenolic resin and it must be above 20 wt.%-50 wt.%of the organic ester hydrolysis amount.(2)High-speed ester A(propylene carbonate)has a higher curing speed than 1,4-butyrolactone,and they were both used as high-speed esters.Glycerol diacetate is not a high-speed ester in alkaline phenolic resin although it was used as a high-speed ester in ester cured sodium silicate sand;glycerol diacetate and glycerol triacetate can be used as medium-speed esters in alkaline phenolic resin.(3)High-speed ester A,medium-speed ester B(glycerol triacetate)and low-speed ester C(dibasic ester,i.e.,DBE)should be used below 15°C,35°C and 50°C,respectively.High-speed ester A or lowspeed ester C should not be used alone but mixed with medium-speed ester B to improve the strength of the resin sand.(4)There should be a suitable solid content(generally 45 wt.%-65 wt.%of resin),alkali content(generally 10 wt.%-15 wt.%of resin)and viscosity of alkaline phenolic resin(generally 50-300 mPa·s)in the preparation of alkaline phenolic resin.Finally,the technique conditions of alkaline phenolic resin preparation and the application principles of organic ester were discussed.展开更多
Resol type phenolic resin/silver nanocomposite was prepared by in-situ reduction method, in which the curing of phenolic resin and the formation of silver nano-particles took place simultaneously. The silver ions wer...Resol type phenolic resin/silver nanocomposite was prepared by in-situ reduction method, in which the curing of phenolic resin and the formation of silver nano-particles took place simultaneously. The silver ions were reduced completely to silver nanoparticles, which were dispersed homogeneously in the resin matrix with narrow size distribution.展开更多
The ceramifiable polymer composite of MgO-Al_(2)O_(3)-SiO_(2)/boron phenolic resin(MAS/BPF)with 40wt%of inorganic fillers was calcined at 1200℃for different time to promote ceramification of ceramifiable composite an...The ceramifiable polymer composite of MgO-Al_(2)O_(3)-SiO_(2)/boron phenolic resin(MAS/BPF)with 40wt%of inorganic fillers was calcined at 1200℃for different time to promote ceramification of ceramifiable composite and improve heat resistance.The effects of different calcine time on the macroscopical morphology,mass loss,phase evolution,microstructure and chemical bond evolution of MAS/BPF composites were characterized by XRD,XPS,and SEM analyses.The experimental results reveal that the increase of calcine time result in the fewer holes,relatively denser and smoother top layer of MAS/BPF composites and protect the interior from deeper decomposition.The final residues of composites are amorphous carbon and C-O-Si-Al-Mg ceramic.And MAS/BPF composites show excellent mass stability,low shrinkage and self-supporting features after 2 h holding compared with BPF composites without 40wt%of inorganic fillers.展开更多
The development of montmorillonite modified phenolic resin under microwave irradiation heating was investigated.The effect of montmorillonite content and stirring time on the structure and morphology of synthetic resi...The development of montmorillonite modified phenolic resin under microwave irradiation heating was investigated.The effect of montmorillonite content and stirring time on the structure and morphology of synthetic resin was analyzed.The optimum processing procedure was found to be 45 min stirring time with 5.4% montmorillonite addition.Further,the platelet spacing increases with stirring time till montmorillonite exfoliated to nanoscales platelet.When montmorillonite is exfoliated,layered structure at nanoscale can be uniformly distributed in the resin.The overall performance of montmorillonite modi fied phenolic resin is improved remarkably,such as flow ability,tensile strength and toughness property of resin coated sand.However,the gelation speed decreased slightly by adding montmorillonite.展开更多
Fluxing agents of zinc borate, antimony oxide, galss frit A and glass frit B, with different melting or softening point temperatures, were added into MgO-Al_2O_3-SiO_2/boron phenol formaldehyde resin(MAS/BPF) compos...Fluxing agents of zinc borate, antimony oxide, galss frit A and glass frit B, with different melting or softening point temperatures, were added into MgO-Al_2O_3-SiO_2/boron phenol formaldehyde resin(MAS/BPF) composites to lower the formation temperature of eutectic liquid phase and promote the ceramification of ceramifiable composites. The effects of fluxing agents on the thermogravimetric properties, phase evolution, and microstructure evolution of MAS/BPF composites were characterized by TG-DSC, XRD and SEM analyses. The results reveal that the addition of a fluxing agent highly reduces the decomposition rate of MAS/BPF composites. Fluxing agents lower the formation temperatures of liquid phases of ceramifiable MAS/BPF composites obviously, and then promote the ceramification and densification process. The final residues of composites are ceramic surrounded by large amount of glass phases.展开更多
The novel epoxidized soybean oil-modified-phenolic resin/clay nanocomposites(ESO-M-PR/ CN) was prepared. The coupling agent-benzyldimethylphenylammonium chloride [C6H5CH2N^+(CH3)2C6H5Cl^- , B2MP] was adopted to m...The novel epoxidized soybean oil-modified-phenolic resin/clay nanocomposites(ESO-M-PR/ CN) was prepared. The coupling agent-benzyldimethylphenylammonium chloride [C6H5CH2N^+(CH3)2C6H5Cl^- , B2MP] was adopted to modify the interface between the organic and inorganic phases. The effect of the nanocomposite structure on its physical and chemical properties was discussed. During the synthesizing process of ESO-M-PR/CN, the phenol hydroxyl was etherified by ESO or ESO epoxy resin prepolymer to provide long ESO epoxy segments. Long ESO epoxy resin chain segments enhanced the crosslink density of ESO-M- PR/CN. The thermal and mechanical properties exhibit a significant improvement. The temperature at which a weight loss of 5% occurs increases from 287.1 ℃ to 402.3 ℃. The flexural strength increases by 25%, while the flexural modulus increases by 39%. Moreover, the properties of resin were enhanced by the effect of the inorganic nanoparticles, while the size of the nanomontmorillonites in the phenolic resin was characterized with a scanning electron microscope. The particle size of inorganic montmorillonites in the modified system is less than 100 nm.展开更多
基金supported by the National Natural Science Foundation of China (Grant Nos. 52171054 and 52171195)the National Natural Science Foundation for Distinguished Young Scholars (Grant No. 51925605)。
文摘We present a simple hot press-based method for processing La(Fe,Si)13-based compounds consisting of La–Fe–Co–Si–C particles and phenolic resin. The magnetic entropy change △S per unit mass for the La Fe_(10.87)Co_(0.63)Si_(1.5)C_(0.2)/phenolic resin compounds have nearly the same magnitude with the base materials. With the content of phenolic resin of 5.0 wt%, the compound conductivity is 3.13 W·m^(-1)·K^(-1). In order to measure the cooling performance of La(Fe,Si)13-based compounds,the La(Fe_(11.6-x)Co_(x))Si_(1.4)C_(0.15)(x =0.60, 0.65, 0.75, 0.80, 0.85)/phenolic resin compounds were pressed into thin plates and tested in a hybrid refrigerator that combines the active magnetic refrigeration effect with the Stirling cycle refrigeration effect. The test results showed that a maximum cooling power of 41 W was achieved over a temperature span of 30 K.
文摘The study characterized the curing behaviors of phenol formaldehyde(PF)resin under different vacuum degrees and explored the properties of 9-ply plywood panels hot-pressed under both vacuum and atmospheric conditions.The changes in core temperature and moisture content of the plywood mats during hot pressing were investigated as well.It was found that the gel times and gel temperatures of PF resin decreased with the increase of vacuum degree using a self-made device.FTIR spectra indicated the degree of polycondensation of hydroxymethyl gradu-ally increased with the increase in temperature.It was also observed that a higher degree of vacuum led to a slower polycondensation reaction rate of PF resin.During different hot-pressing processes,the bonding strengths in the innermost and uppermost gluelines of the vacuum hot-pressed plywood panels were up to 30%–50%higher than their counterparts of conventional hot-pressed products.A less difference in the bonding strengths between these two gluelines was also observed for vacuum hot-pressed products.In addition,the core of vacuum hot-pressed plywood was found to have a greater heating rate and higher temperature at thefinal stage of hot pressing,which was beneficial to cure the PF resin.The results from this study indicate a promising potential of introducing a vacuum during hot pressing to improve the quality and productivity of plywood products and provide a basis for adopting vacuum to hot press wood composites.
基金Supported by Shanghai Aerospace Science and Technology Innovation Fund Project (SAST 2022-097)。
文摘Benzoxazine resin,being a new type of phenolic resin deve-loped to overcome the shortcomings of traditional phenolic resins,has been synthesized from phenol,formaldehyde and amine,and does not require solvent elimination or monomer purification to obtain a relatively clean precursor.It has potential application in the field of aerospace due to its low expansion coefficient,high weather resistance,high carbon yield,good mechanical strength,and excellent ablation resistance[1].It can be mixed with various other resins or polymers to produce new resins with a broad range of applications[2-3].
文摘In-situ reactive compatibilization of high-density polyethylene (HDPE)/ground tire rubber (GTR) blends by dicumyl peroxide (DCP) and HY-2045 - a kind of thermoplastic phenolic resin without catalyst was investigated by studying the mor-phology, stress and strain behavior, dynamic mechanical properties and crystallization performance of the blends. Scanning e-lectron microscopy (SEM) results show that there are a lot of fibrous materials distributing in the interface, which connects the dispersed phase with the matrix and obtains better interfacial strength for prominent mechanical properties. The addition of compatibilizers results in the decrease of crystallinity of the blends and the disappearance of an obvious yield phenomenon, which was proved by the differential scanning calorimeter (DSC) test and X-ray diffraction (XRD) characterization Although the crystallinity of the blends decreases,the tensile strength and tensile strain of the blends significantly increases, especially for the HDPE/GTR/DCP/HY-2045 blends, which is possibly attributed to the good compatibility of the blends owing to the in-situ interface crosslinking. In addition, it is found that the compatibilizing HDPE/GTR blends shows a higher tan^ peak temperature and a broaden transition peak for GTR phase.
文摘Phenolic resin/montmorillonite intercalation composites were prepared by using the methods of pressing intercalation and melt intercalation.Properties and structure of the composites were investigated by using XRD,TG and test of softening point.It is indicated that both the pressing intercalation and melt intercalation can be used to prepare the phenolic resin/organo-montmorillonite intercalation nanocomposites.Compared with phenolic resin,the intercalation nanocomposites have better heat-resistance,higher decomposition temperatures and less thermal weight-loss.However,these two intercalation methods have different effects on the softening point of the intercalation nanocomposites.Pressing intercalation almost does not affect the softening point of the intercalation nanocomposites,while melt intercalation significantly increases the softening point of the intercalation nanocomposites, probably due to the chemical actions happening in the process of melt intercalation.
基金supported by project of Hubei Provincial Department of Education,China(No.Q20083003)the Innovative Team of Huangshi Institute of Technology.
文摘A novel benzoxazine-based phenolic resin containing furan groups(PFB) was synthesized via simple two-step reactions and the structure of PFB was confirmed by FTIR and ~1H NMR spectra.Differential scanning calorimetry(DSC) showed that the polybenzoxazine cured from PFB had good heat resistance and lower polymerization temperature compared with that of benzoxazine-based phenolic resins.
基金This work was supported by the "The National High Technology Research and Development Program" of Ministry of Science and Technology of China (No. 2002AA333020).
文摘The dynamic mechanical properties of a new blend system consisting of phenol resin and polar polymer (acrylaterubber and/or chlorinated polypropylene) were investigated. It was found that the addition of phenol resin to acrylate rubberand its incompatible blend can cause a remarkable improvement in the temperature dependence of the loss tangent. As a result, the present blends are very good damping materials.
基金Supported by the National Natural Science Foundation of China (No.50172034).
文摘Mesocarbon microbeads (MCMB) were prepared from coal tar pitch modified by phenolic resin and from the same pitch modified by phenolic resin and hexamethylenetetramine at 440℃ for lh. By investigating the morphology of mesophase spheres and the structure of the MCMB carbonized at 1000℃ for lh using scanning electron microscope (SEM) and XRD, it was found that phenolic resin accelerated the formation and coalescence of mesophase spheres. Some of the obtained MCMB were hi- or tri-spheres with the distorted microtextural carbon layers. Hexamethylenetetramine in the pitch modified by phenolic resin accelerated the condensation of phenolic resin and consequently expedited the combination of mesophase spheres, which was proved by the formation of some tetra-spheres. Owing to the cross-linkage of the additives, MCMB with complex structure were obtained.
基金This Work was financially supported by Beijing Municipal Science & Technology Commission(No.2052015).
文摘Nanosized tungsten carbide was synthesized from phenol formaldehyde resin (PF) coated tungsten precursors. The process has three steps in which nanosized tungsten particles were first coated with PF, then the precursors were carburized at 950℃, and finally the carburized powders were treated in flowing wet hydrogen atmosphere at 940℃ to remove the uncombined carbon. The obtained powders were characterized using X-ray diffraction analysis (XRD), field-emission scanning electron microscopy (FESEM), small angle X-ray scattering (SAXS), and combustion-gas-volume method. The results indicated that single-phase WC could be synthesized using excessive PF as carburizer at a much lower temperature compared with using mixed carbon black. After wet hydrogen treating, the mean size of the obtained WC particles was 94.5 nm and the total carbon content was 6.18 wt.%.
基金This project was supported by the National Natural Science Foundation of China (No. 29974015).
文摘This paper presents experimental observations on the adsorption of individual solutes by a simple thermodynamic framework, and the equilibrium adsorption of ethyl benzoate and diethyl phthalate on phenolic resin adsorbent in hexane solutions within the temperature range of 293-313 K. The experimental results show that the Freundlich adsorption law is applicable to the adsorption of ethyl benzoate and diethyl phthalate on the adsorbent, since all the correlative factors R' are larger than 0.99. The negative values of all the isosteric adsorption enthalpies for ethyl benzoate and diethyl phthalate indicate that they undergo exothermic processes, while their magnitudes (19-28 kJ/mol) manifest a hydrogen bonding sorption process. Other thermodynamic properties: the free energy changes and the entropy change associated with the adsorption have been calculated from the Gibbs adsorption equation and the Gibbs-Helmholtz equation
基金Supported by the Key Science&Technology Item of Guangdong Province(TC05B372-6).
文摘A novel epoxidized soybean oil-toughened-phenolic resin(ESO-T-PR)has been synthesized by etheri- fication graft and multi-amine curing ESO.Fourier transform infrared spectroscopy(FTIR)was adopted to investi- gate its molecular structure and scan electron microscope(SEM)was used to observe the micro morphology of its impact fracture surface.This ESO-T-PR was adopted as the matrix resin to prepare paper copper clad laminate (P-CCL)and the properties of resulting P-CCL are found superior to the related Chinese National Standard.The toughing mechanism was investigated by comparing the impact strength,solderleaching resistance,flexural strength, peeling strength and morphology of this ESO-T-PR with those of other two ESO modified phenolic resins.It is demonstrated that during the synthesizing process of ESO-T-PR,the phenol hydroxyl is etherified by ESO or ESO epoxy resin prepolymer(ESO chain extension polymer)and the long ESO epoxy resin chain segments enhance the crosslink density of ESO-T-PR and consequently improve the impact toughness and solderleaching resistance of P-CCL made of ESO-T-PR.The ESO-T-PR is a cheap matrix resin with excellent properties to make P-CCL(elec- tric guide board).
基金Supported by the Key Research Program Foundation, Ministry of Education of China (Grant No. 02021)and the National Science Foundation of China (Grant No. 30471351)
文摘Wood of Chinese fir and poplar were liquefied in phenol at 150℃ and atmospheric pressure. The liquefied wood were reacted with formaldehyde to synthesize the liquefied wood-based resin. The factors affecting the resinification and the properties of new resin were investigated. The results show that the formaldehyde/liquefied wood molar ratio, reaction temperature, reaction time and sodium hydroxide/liquefied wood molar ratio have important influence on the resin characteristics. With the increase of formaldehyde/liquefied wood molar ratio, the yield of resin increases, and the flee phenol content of resins decreases, showing that the resinification of liquefied wood is more complete at higher formaldehyde/liquefied wood molar ratios. The reaction temperature on the viscosity of the liquefied resin has considerable effect; the viscosity of resin increased with increasing reaction temperature, and the amount of liquefied poplar resin increased more quickly than that of liquefied Chinese fir resin. The resinification time also has obvious influence on the viscosity of resin; the viscosity of liquefied poplar resin is more sensitive to resinification time compared with that of liquefied Chinese fir. The amount of sodium hydroxide can improve the water miscibility of liquefied wood resin. The optimum sodium hydroxide/liquefied wood molar ratio for preparation of liquefied wood-based resins exceeds 0.4.
文摘New water soluble and photocrosslinkable prepolymers containing acrylate and quaternary ammonium salt groups were synthesized from epoxy phenolic resin via ring-opening reaction with acrylic acid and with aqueous solution of triethylamine hydrochloride successively. The second reaction needs no phase transfer catalyst to accelerate, since the product formed can act as a phase transfer catalyst. The prepolymer obtained contains both photocrosslinkable acrylate groups and hydrophilic quaternary ammonium salt groups. Optimum conditions for these reactions were studied. The photosensitivity of the prepolymer was also investigated. The effects of different photoinitiators, different crosslinkable diluent monomers and amine accelerator on the photosensitivity of the prepolymer were compared. The photoinitiator of hydrogen abstraction type is still effective without using amine or alcohol as accelerator, because the prepolymer contains a H beside the OH groups formed in the ring-opening reactions.
文摘To study the curing mechanism of alkaline phenolic resin with organic ester, three esters were chosen to react with three systems - alkaline phenolic resin, potassium hydroxide aqueous solution containing phenol, and potassium hydroxide aqueous solution. The variations of pH, heat release and gel pH during the reactions were monitored and measured. Infrared spectroscopy (IR) and thermal gravity analysis (TG) techniques were used to characterize the curing reaction. It was found that organic ester is only partial y hydrolyzed and resin can be cured through organic ester hydrolysis process as wel as the reaction with redundant organic ester. The sequential curing mechanism of alkaline phenolic resin cured by organic ester was identified as fol ows: a portion of organic ester is firstly hydrolyzed owing to the effect of the strong alkaline; the gel is then formed after the pH decreases to about 10.8-10.88, meanwhile, the redundant organic ester (i.e. non-hydrolysis ester) starts the curing reaction with the resin. It has also been found that the curing rate depends on the hydrolysis velocity of organic ester. The faster the hydrolysis speed of the ester, the faster the curing rate of the resin.
文摘Five organic esters with different curing speeds:propylene carbonate(i.e.high-speed ester A);1,4-butyrolactone;glycerol triacetate(i.e.medium-speed ester B);glycerol diacetate;dibasic ester(DBE)(i.e.lowspeed ester C),were chosen to react with alkaline phenolic resin to analyze the application conditions of ester cured alkaline phenolic resin.The relationships between the curing performances of the resin(including pH value,gel pH value,gel time of resin solution,heat release rate of the curing reaction and tensile strength of the resin sand)and the amount of added organic ester and curing temperature were investigated.The results indicated the following:(1)The optimal added amount of organic ester should be 25 wt.%-30 wt.%of alkaline phenolic resin and it must be above 20 wt.%-50 wt.%of the organic ester hydrolysis amount.(2)High-speed ester A(propylene carbonate)has a higher curing speed than 1,4-butyrolactone,and they were both used as high-speed esters.Glycerol diacetate is not a high-speed ester in alkaline phenolic resin although it was used as a high-speed ester in ester cured sodium silicate sand;glycerol diacetate and glycerol triacetate can be used as medium-speed esters in alkaline phenolic resin.(3)High-speed ester A,medium-speed ester B(glycerol triacetate)and low-speed ester C(dibasic ester,i.e.,DBE)should be used below 15°C,35°C and 50°C,respectively.High-speed ester A or lowspeed ester C should not be used alone but mixed with medium-speed ester B to improve the strength of the resin sand.(4)There should be a suitable solid content(generally 45 wt.%-65 wt.%of resin),alkali content(generally 10 wt.%-15 wt.%of resin)and viscosity of alkaline phenolic resin(generally 50-300 mPa·s)in the preparation of alkaline phenolic resin.Finally,the technique conditions of alkaline phenolic resin preparation and the application principles of organic ester were discussed.
基金Financial support from Chinese Academy of Sciences (CMS-CX200105) is gratefully acknow- ledged.
文摘Resol type phenolic resin/silver nanocomposite was prepared by in-situ reduction method, in which the curing of phenolic resin and the formation of silver nano-particles took place simultaneously. The silver ions were reduced completely to silver nanoparticles, which were dispersed homogeneously in the resin matrix with narrow size distribution.
基金Funded by the Joint Fund of Ministry of Education for Equipment Pre-research(Nos.6141A02022250 and SAST2018-067)。
文摘The ceramifiable polymer composite of MgO-Al_(2)O_(3)-SiO_(2)/boron phenolic resin(MAS/BPF)with 40wt%of inorganic fillers was calcined at 1200℃for different time to promote ceramification of ceramifiable composite and improve heat resistance.The effects of different calcine time on the macroscopical morphology,mass loss,phase evolution,microstructure and chemical bond evolution of MAS/BPF composites were characterized by XRD,XPS,and SEM analyses.The experimental results reveal that the increase of calcine time result in the fewer holes,relatively denser and smoother top layer of MAS/BPF composites and protect the interior from deeper decomposition.The final residues of composites are amorphous carbon and C-O-Si-Al-Mg ceramic.And MAS/BPF composites show excellent mass stability,low shrinkage and self-supporting features after 2 h holding compared with BPF composites without 40wt%of inorganic fillers.
文摘The development of montmorillonite modified phenolic resin under microwave irradiation heating was investigated.The effect of montmorillonite content and stirring time on the structure and morphology of synthetic resin was analyzed.The optimum processing procedure was found to be 45 min stirring time with 5.4% montmorillonite addition.Further,the platelet spacing increases with stirring time till montmorillonite exfoliated to nanoscales platelet.When montmorillonite is exfoliated,layered structure at nanoscale can be uniformly distributed in the resin.The overall performance of montmorillonite modi fied phenolic resin is improved remarkably,such as flow ability,tensile strength and toughness property of resin coated sand.However,the gelation speed decreased slightly by adding montmorillonite.
文摘Fluxing agents of zinc borate, antimony oxide, galss frit A and glass frit B, with different melting or softening point temperatures, were added into MgO-Al_2O_3-SiO_2/boron phenol formaldehyde resin(MAS/BPF) composites to lower the formation temperature of eutectic liquid phase and promote the ceramification of ceramifiable composites. The effects of fluxing agents on the thermogravimetric properties, phase evolution, and microstructure evolution of MAS/BPF composites were characterized by TG-DSC, XRD and SEM analyses. The results reveal that the addition of a fluxing agent highly reduces the decomposition rate of MAS/BPF composites. Fluxing agents lower the formation temperatures of liquid phases of ceramifiable MAS/BPF composites obviously, and then promote the ceramification and densification process. The final residues of composites are ceramic surrounded by large amount of glass phases.
基金the Key Science & Technology Item of Guangdong province (No. TC05B372-6)
文摘The novel epoxidized soybean oil-modified-phenolic resin/clay nanocomposites(ESO-M-PR/ CN) was prepared. The coupling agent-benzyldimethylphenylammonium chloride [C6H5CH2N^+(CH3)2C6H5Cl^- , B2MP] was adopted to modify the interface between the organic and inorganic phases. The effect of the nanocomposite structure on its physical and chemical properties was discussed. During the synthesizing process of ESO-M-PR/CN, the phenol hydroxyl was etherified by ESO or ESO epoxy resin prepolymer to provide long ESO epoxy segments. Long ESO epoxy resin chain segments enhanced the crosslink density of ESO-M- PR/CN. The thermal and mechanical properties exhibit a significant improvement. The temperature at which a weight loss of 5% occurs increases from 287.1 ℃ to 402.3 ℃. The flexural strength increases by 25%, while the flexural modulus increases by 39%. Moreover, the properties of resin were enhanced by the effect of the inorganic nanoparticles, while the size of the nanomontmorillonites in the phenolic resin was characterized with a scanning electron microscope. The particle size of inorganic montmorillonites in the modified system is less than 100 nm.