Preparation of Environmentally Friendly Urea-Hexanediamine-Glyoxal(HUG)Resin Wood Adhesive

Using non-toxic,low-volatile glyoxal to completely replace formaldehyde for preparing urea-glyoxal(UG)resin adhesive is a hot research topic that could be of great interest for the wood industry.However,urea-glyoxal(UG)resins prepared by just using glyoxal instead of formaldehyde usually yields a lower degree of polymerization.This results in a poorer bonding performance and water resistance of UG resins.A good solution is to pre-react urea to preform polyurea molecules presenting already a certain degree of polymerization,and then to condense these with glyoxal to obtain a novel UG resin.Therefore,in this present work,the urea was reacted with hexamethylene diamine to form a polyurea named HU,and then this was used to react it with different amounts of glyoxal to synthesize hexamethylenediamine-urea-glyoxal(HUG)polycondensation resins,and to use this for bonding plywood.The results show that the glyoxal can well react with HU polyuria via addition and schiff base reaction,and also the HUG resin exhibits excellent bonding strength and water resistance.The shear strength of the plywood bonded with this HUG at 160°C hot press temperature as high as 1.93 MPa,2.16 MPa and 1.61 MPa,respectively,which meets the requirement of the China national standard GB/T 9846-2015(≥0.7 MPa),and can be a good choice as a wood adhesive for industrial application.

MUF Resins Improved by Citric Acid as Adhesives for Wood Veneer Panels

This article presents the first applied results of using citric acid in combinations with a melamine-urea-formal-dehyde(MUF)resin for bonding wood veneers.The chemical reactions involved are shown based on a MALDI ToF analysis of the reaction of the MUF resin with citric acid.The preliminary results of the physical and mechanical properties of the LVL prepared are also presented.Veneers from Populus sp were used to manufacture 5-layer laminated veneer lumber(LVL)of small dimensions.Five combinations of the amount of citric acid,MUF spread rate and pressing parameters were tested.LVL bonded with 20%of citric acid+100 g/m^(2)of MUF,hot-pressed using a 3-step process with maximum 1.5 MPa of pressure yielded the board with better dimensional stability and mechanical properties.It could be concluded that citric acid in combination with MUF can be used for bonding wood veneer and the research should be continued to study further the parameters involved and to enhance the results.

A Boron-based Adhesion Aid for Efficient Bonding of Silicone Rubber and Epoxy Resin

We improved the adhesion between silicon based insulating materials and epoxy resin composites by adding the adhesion promoter cycloborosiloxane(BSi,cyclo-1,3,3,5,7,7-hexaphenyl-1,5-diboro-3,7-disiloxane).The experimental results show that the addition of BSi in the silicone rubber(SR)system significantly increases the tensile shear strength between BSi and epoxy resin(EP),reaching 309%of the original value.On this basis,the mechanism of BSi to enhance the adhesion effect was discussed.The electron deficient B in BSi attracted the electron rich N and O in EP to enhance the chemical interaction,combined with the interfacial migration behavior in the curing process,to improve the adhesion strength.This study provides the design and synthesis ideas of adhesive aids,and a reference for further exploring the interface mechanism of epoxy resin matrix composites.

Curing reaction and mechanism of phenol-formaldehyde novolac resins for foundry

In this study on the curing dynamics of phenol-formaldehyde novolac resins(PFNR) and hexamethylene tetramine(HMTA), two typical commercial PFNR were selected as examples and the curing reactions of the resins with HMTA were studied by differential scanning calorimetry(DSC). Based on the data calculated by the Kissinger equation and the Crane equation, a thermocuring dynamic model was established, from which the process conditions, activation energy, reaction kinetics equation and a f irst-order reaction of the curing reactions were derived.

Reinforcement of Lignin-Based Phenol-Formaldehyde Adhesive with Nano-Crystalline Cellulose (NCC): Curing Behavior and Bonding Property of Plywood

The curing behavior of lignin-based phenol-formaldehyde (LPF) resin with different contents of nano-crystalline cellulose (NCC) was studied by differential scanning calorimetry (DSC) at different heating rates (5, 10 and 20&degC/min) and the bonding property was evaluated by the wet shear strength and wood failure of two-ply plywood panels after soaking in water (48 hours at room temperature and followed by 1-hour boiling). The test results indicated that the NCC content had little influence on the peak temperature, activation energy and the total heat of reaction of LPF resin at 5 and 10&degC/min. But at 20&degC/min, LPF0.00% (LPF resin without NCC) showed the highest total heat of reaction, while LPF0.25% (LPF resin containing 0.25% NCC content) and LPF0.50% (LPF resin containing 0.50% NCC content) gave the lowest value. The wet shear strength was affected by the NCC content to a certain extent. With regard to the results of one-way analysis of variance, the bonding quality could be improved by NCC and the optimum NCC content ranged from 0.25% to 0.50%. The wood failure was also affected by the NCC content, but the trend with respect to NCC content was not clear.

Study on binder system of CO_2-cured phenol-formaldehyde resin used in foundry

A new aqueous alkaline resol phenol-formaldehyde resin has been prepared from phenol and formaldehyde using NaOH as catalyst; the optimum synthetic process has been determined. With addition of some cross-linking agents, after passing carbon dioxide gas through the resin bonded sand, high as-gassed strength and 24 h strength are achieved. The bonding bridge of the resin bonded sand fracture has been analyzed by using SEM.

Study on Camellia Oleifera Protein based Wood Adhesive by Epoxy Resin and Its Crosslinking Mechanism

Epoxy resin (EPR) was used to crosslink with Camellia oleifera Abel.protein to prepare wood adhesive,and the bonding performance and curing characteristics of which were mainly investigated,and the synthesis mechanism was also discussed by using model compounds.The experimental results show that EPR can significantly improve the bonding performance of Camellia oleifera Abel.protein-based adhesive,and the maximum of which reaches 0.72 MPa satisfies the strength requirement of Type II plywood in GB/T 17657-2013.After alkali treatment,the protein can more easily crosslink with EPR at low curing temperature,and the adhesive has high degree of crystallinity of curing products,high degree of crosslinking reaction,and high bonding strength.The reaction mechanism of EPR-modified Camellia oleifera Abel.protein adhesive can be divided into resinification phase and curing phase.

Determination of Water Diffusion Coefficients and Dynamics in Adhesive/Carbon Fiber Reinforced Epoxy Resin Composite Joints

To determinate the water diffusion coefficients and dynamics in adhesive/carben fiber reinforced epoxy resin composite joints, energy dispersive X-ray spectroscopy analysis（EDX） is used to establish the content change of oxy- gen in the adhesive in adhesive/carbon fther reinforced epoxy resin composite joints. As water is made up of oxygen and hydrogen, the water diffusion coefficients and dynamics in adhesive/carben fiber reinforced epoxy resin composite joints can be obtained from the change in the content of oxygen in the adhesive during humidity aging, via EDX analy-sis. The authors have calculated the water diffusion coefficients and dynamics in the adhesive/carbon fiber reinforced epoxy resin composite joints with the aid of beth energy dispersive X-ray spectroscopy and elemental analysis. The de- termined results with EDX analysis are almost the same as those determined with elemental analysis and the results al- so show that the durability of the adhesive/carbon fther reinforced epoxy resin composite joints subjected to silane cou- pling agent treatment is better than those subjected to sand paper burnishing treatment and chemical oxidation treat- ment.

SEM Comparison of Penetration in Artificial White Spots Lesion between an Infiltrant Resin and Two Adhesive Systems

White spot infiltration emerged as an alternative of non-invasive treatment to halt progression of the lesion, through the use of low viscosity resins that would permeate the porous enamel and form a physical barrier that would prevent the acid diffusion produced by micro-organisms. Purpose: To compare penetration levels in artificial white spot lesions, of infiltrant resin ICON™and 2 conventional adhesives systems, XP-Bond™and Single Bond 2™. Methodology: White spot lesions (ICDAS code 2) were caused in 75 premolars or third molars were extracted in good conditions, by immersion in a 0.1 M lactic acid solution (pH 4.5) at 37℃ for 8 weeks. They were divided randomly into 3 groups of 25 samples and applied the following resins, Group A: ICON™, B: XP-Bond™and C: Single Bond 2™. Subsequently, the enamel was removed with hydrochloric acid to expose resin saturated area and the samples were metalized with Au-Pd for SEM observation. The resin tags lengths were measured on microphotographs through software, and the values were analyzed with the statistics ANOVA and Scheffé post-test. Results: There were significant differences (p ™(82.7 μm ± 26.8 μm) compared to adhesive systems XP-Bond™(58.5 μm ± 29.3 μm) and Single Bond 2™(44.8 μm ± 32.5 μm). We found no significant differences between the two adhesive systems (p > 0.05). Conclusion: Under the conditions tested, the penetration of infiltrant ICON was significantly higher than the adhesive systems;however, it removes the surface layer of the enamel.

NaOH and Ba(OH)_2 Compound Catalyzed PhenolResorcinol-Formaldehyde Copolycondensation Resin Adhesive for Recombined Bamboo

In order to reduce the curing temperature, shorten the curing time of phenol-formaldehyde(PF) resin adhesive, and ensure the good water-solubility, NaOH and Ba(OH)_2 were used as compound catalysts. The influences of the adding time of Ba(OH)_2, the adding amount of NaOH, Ba(OH)_2 and resorcinol on the properties of adhesives were studied. The properties of NaOH catalyzed phenol-formaldehyde(PF) adhesive, NaOH and Ba(OH)_2 compound catalyzed PF adhesive, NaOH and Ba(OH)_2 compound catalyzed phenol-resorcinol-formaldehyde(PRF) adhesive, and the prepared recombinant bamboo with three kinds of adhesives were compared. The experimental results show that NaOH and Ba(OH)_2 compound catalyst not only shortens the curing time of PF adhesive, but also guarantees the suitable water solubility of adhesive. After copolycondensation with resorcinol, the curing time of adhesive is further shortened, the water solubility is improved obviously, and the highest bonding strength is obtained. Infrared spectrum analysis shows that the reaction activity point of NaOH and Ba(OH)_2 compound catalyzed PRF adhesive will increase, so that both the curing temperature and curing enthalpy decrease.

Effect of Self-adhesive Resin Cement and Tribochemical Treatment on Bond Strength to Zirconia

Aim To evaluate the interactive effects of different self- adhesive resin cements and tribochemical treatment on bond strength to zirconia. Methodology The following self-adhesive resin cements for bonding two zirconia blocks were evaluated： Maxcem （MA）, Smartcem （SM）, Rely X Unicem Aplicap （UN）, Breeze （BR）, Biscem （BI）, Set （SE）, and Clearfil SA luting （CL）. The specimens were grouped according to conditioning as follows： Group 1, polishing with 600 grit polishing paper; Group 2, silica coating with 110 μm Al2O3 particles which modified with silica; and, Group 3, tribochemical treatment - silica coating ＋ silanization. Specimens were stored in distilled water at 37℃ for 24 hours before testing shear bond strength. Results Silica coating and tribochemical treatment significantly increased the bond strength of the MA, UN, BR, B1, SE and CL to zirconia compared to #600 polishing. For both #600 polished and silica coating treatments, MDP- containing self-adhesive resin cement CL had the highest bond strengths to zirconia. Conclusion Applying silica coating and tribochemical treatment improved the bond strength of self-adhesive resin cement to zirconia, especially for CL.

YbF_3/SiO_2 Fillers as Radiopacifiers in a Dental Adhesive Resin

The objective of this study was to evaluate the effect of functionalizing a dental adhesive resin with YbF_3/SiO_2 fillers for use as radiopacifiers.Particles of YbF_3/SiO_2 were obtained with the high-energy mechanical milling method and characterized by both physical and chemical methods.After characterization,the particles were sieved and silanized prior to being incorporated into an adhesive resin.The stability of the particle suspension was then evaluated.After light activation,the radiopacity,degree of conversion,flexural strength and elastic modulus were determined.The dental adhesive resins with 10 and 15 wt% of filler provided satisfactory radiopacity,while flexural strength and elastic modulus were not affected.The degree of conversion was statistically lower than that of the control(p<0.05).The method used for incorporating the tested ytterbium fluoride/silicon dioxide particles at concentrations of 10 and 15 wt% was shown to be feasible for the development of a radiopaque dental adhesive system.

Effect of enamel-grinding on adhesionstrength of enamel-resin junction

In this paper,we have tested the normal and mottled enamel in order to get some instructive information for the clinical treatment. As demonstrated by the results of our experiments, the grinding treatment of the enamel superficial layer has no significant improvement on the adhesional strength of the junction between the normally developed teeth and the resin. However, it does exhibit evident effect on the adhesional strength of the junction between the fluorosis teeth and the repairing resin.

水利工程用环氧树脂改性聚氨酯丙烯酸酯性能研究

水利工程金属结构和水工建筑物常遭受腐蚀、高速含沙水流磨蚀破坏,需对其进行便捷有效的防护。利用环氧树脂对聚氨酯丙烯酸酯(PUA)进行改性提高PUA与基体黏结性能,采用紫外光(UV)固化技术制备PUA涂层。研究了环氧树脂改性PUA的化学结构及环氧树脂用量对PUA的力学性能、热稳定性能、耐溶剂性能和抗冲磨性能的影响。结果表明,环氧树脂改性PUA的拉伸强度随着环氧树脂用量增加,呈下降趋势,当加入5%时,PUA拉伸强度为103.0 MPa,材料呈强而脆的特性。环氧树脂加入提升了PUA的拉伸剪切强度,由0.25 MPa增至1.60 MPa。同时,环氧树脂改性PUA具有良好的耐水性能、耐溶剂性能、抗冲磨性能,5%环氧树脂改性PUA抗冲磨强度为800 h/(kg·m^(2))。

无枝状结晶耐离子迁移覆盖膜的研究

挠性印制电路板(FPCB)的离子迁移主要受挠性覆铜板(FCCL)和覆盖膜胶层的影响,表现为线路间的枝状结晶。考察采用环氧胶、聚酰亚胺胶等胶黏剂制备覆盖膜的耐离子迁移性,观察耐离子迁移性测试后的试样形貌,发现不同类型胶黏剂制备的覆盖膜试样枝状结晶程度不一,其中普通环氧胶覆盖膜试样线路间枝状结晶严重。进一步通过胶黏剂配方研究,开发出一种无枝状结晶的环氧胶覆盖膜,性能满足IPC-4203标准要求。

石墨烯增强环氧树脂胶黏剂的研究进展

环氧树脂胶黏剂具有较高的强度、硬度和耐化学腐蚀性,故其应用越来越广泛。但它也存在一些缺点,如热稳定性差、导电性差等。二维石墨烯是一种具有高强度、高导电性、大比表面积等优异性能的材料,在环氧树脂胶黏剂中添加石墨烯可增强其性能。综述了石墨烯-环氧复合材料的制备及石墨烯对环氧胶黏剂的影响,展望了石墨烯-环氧复合材料的应用前景。未来,在石墨烯-环氧复合材料合成与加工过程中还需解决石墨烯的均匀分散、生产的可扩展性、与环氧树脂及固化剂的相容性等问题。

三种不同树脂粘结系统对纤维桩粘结效果的影响

目的评价全酸蚀粘结系统、自酸蚀粘结系统及自粘结树脂对纤维桩粘结效果的影响。方法选取2021年10月至2022年3月于泰州职业技术学院口腔门诊部行前牙纤维桩修复的82例患者(共122颗前牙)作为研究对象,按照不同树脂粘结系统将其分为全酸蚀组(28例,40颗)、自酸蚀组(26例,40颗)及自粘结组(28例,42颗)。全酸蚀组使用Tetric-N Bond全酸蚀树脂粘结剂对纤维桩进行粘结,自酸蚀组使用All-Bond Universal自酸蚀树脂粘结剂对纤维桩进行粘结,自粘结组使用Relyx Unicem自粘结树脂对纤维桩进行粘结,完成纤维桩粘结后行全瓷冠修复。比较三组纤维桩核的稳固率及全瓷冠修复体的红色美学指数(PES)、白色美学指数(WES)评分。结果粘结6、12、18个月后,三组纤维桩核的稳固率组间及组内比较,差异无统计学意义(P>0.05)。粘结18个月后,三组全瓷冠修复体的PES、WES评分比较,差异无统计学意义(P>0.05)。结论三种树脂粘结系统对纤维桩的粘结效果在短期内相当,远期效果还需进一步的观察。

苯酚-甲醛树脂MK-95在轿车子午线轮胎胎体胶中的应用

研究苯酚-甲醛树脂MK-95(简称MK-95)在轿车子午线轮胎胎体胶中的应用。结果表明:MK-95不含游离间苯二酚和其他添加剂,其软化点和挥发分含量低于间苯二酚-甲醛树脂;在胎体胶中以MK-95等量替代间苯二酚-甲醛树脂,胶料的硫化特性、物理性能、动态力学性能和粘合性能相当,成品轮胎的高速、耐久和路试性能均达到要求。

毛竹纤维改性酚醛树脂运动装备专用胶黏剂制备研究

酚醛树脂具有良好的耐磨损性和热稳定性,常被用于粘接篮球鞋的碳纤维板、TPU板等。为降低酚醛树脂胶黏剂的制备成本并在一定程度上提升其综合性能,以毛竹纤维、苯酚、甲醛等为原材料制备了一种毛竹纤维改性酚醛树脂篮球鞋专用胶黏剂,对该胶黏剂的综合性能进行试验分析。结果表明:毛竹纤维、苯酚质量比为1.0:4.5,甲醛、氢氧化钠与苯酚摩尔比为1.8:0.4:1.0时,毛竹纤维改性酚醛树脂胶黏剂的综合性能最佳,可以更好地满足高端篮球鞋的需求。

混凝土外墙面装饰用改性环氧树脂胶粘剂制备及应用

为了提高建筑外墙装饰用混凝土胶粘剂性能。以环氧树脂为原料,以乙酸乙酯为稀释剂,以三苯基膦盐为固化剂制备了建筑外墙装饰用混凝土环氧树脂胶粘剂,并对其性能进行了测试表征。结果表明,冷环境下,随着温度降低混凝土与砖板粘接试件的粘接强度、剥离强度不断下降,冲击强度极速下降,而剪切强度变化并不显著;热环境下,随着温度升高试件的粘接强度、剪切强度、冲击强度并未显著变化,而剥离强度缓慢下降;湿环境下,随着湿度增加试件的粘接强度、剥离强度、剪切强度、剪切强度均明显下降;随着挠度增大,试件的抗压强度呈现为显著变大趋势;环氧树脂胶粘剂表观性能与环保性能表现优异,且整体承载力与抗压强度明显提高。