Synthesis of Spherical (Y,Gd)BO_3:Eu^(3+)Phosphor Using W/O Emulsion System

Spherical （Y, Gd）BO3：Eu^3＋ phosphor particles with a narrow size distribution（2 -4 μm） was obtained by firing the Y-Gd-Eu-BO3 precursor prepared in a W/O style emulsion system. In the W/O emulsion system, kerosene, used as oil phase, was mixed with Span 80 and Tween 80 compounds which were employed as the emulsifier with an HLB （hydrophile-lipophile balance） value of 5.2- 5.3. Both rare earths （Y, Gd and Eu） nitrate and boric acid solution or ammonia solution were used as aqueous phase. The synthesis conditions, such as emulsion composition, emulsifying style, precipitation reaction process, reaction temperature, morphology control, and so on, were investigated, and the optimum synthesis conditions for preparing spherical （Y, Gd）BO3：Eu^3＋ phosphor was obtained. The phosphor was characterized by XRD, SEM, laser particle size analysis, emission and excitation spectrum under vacuum ultraviolet （VUV）, and so on. The phosphor synthesized using the water-in-oil emulsion method with median diameter （D50） of 2 - 4 μm shows agreeable photoluminescence （PL） property and sphericity. The main emission peak appears at about 593 nm, which corresponds to ^5D0→^7F1 transition （magnetic-dipole transition） of the Eu^3＋ ion. The cell parameters and powder diffraction data were indexed. The structure of the phosphor belongs to the hexagonal system with space group P63/m.

Pillar effect induced by ultrahigh phosphorous/nitrogen doping enables graphene/MXene film with excellent cycling stability for alkali metal ion storage

Graphene's large theoretical surface area and high conductivity make it an attractive anode material for potassium-ion batteries(PIBs).However,its practical application is hindered by small interlayer distance and long ion transfer distance.Herein,this paper aims to address the issue by introducing MXene through a simple and scalable method for assembling graphene and realizing ultrahigh P doping content.The findings reveal that MXene and P-C bonds have a "pillar effect" on the structure of graphene,and the P-C bond plays a primary role.In addition,N/P co-doping introduces abundant defects,providing more active sites for K^(+) storage and facilitating K^(+) adsorption.As expected,the developed ultrahigh phosphorous/nitrogen co-doped flexible reduced graphene oxide/MXene(NPrGM) electrode exhibits remarkable reversible discharge capacity(554 mA hg^(-1) at 0.05 A g^(-1)),impressive rate capability(178 mA h g^(-1) at 2 A g^(-1)),and robust cyclic stability(0.0005% decay per cycle after 10,000 cycles at 2 A g^(-1)).Furthermore,the assembled activated carbon‖NPrGM potassium-ion hybrid capacitor(PIHC) can deliver an impressive energy density of 131 W h kg^(-1) and stable cycling performance with 98.1% capacitance retention after5000 cycles at 1 A g^(-1).Such a new strategy will effectively promote the practical application of graphene materials in PIBs/PIHCs and open new avenues for the scalable development of flexible films based on two-dimensional materials for potential applications in energy storage,thermal interface,and electromagnetic shielding.

Durable hierarchical phosphorus‐doped biphase MoS_(2)electrocatalysts with enhanced H^(*)adsorption

Phase engineering is an efficient strategy for enhancing the kinetics of electrocatalytic reactions.Herein,phase engineering was employed to prepare high‐performance phosphorous‐doped biphase(1T/2H)MoS_(2)(P‐BMS)nanoflakes for hydrogen evolution reaction(HER).The doping of MoS_(2)with P atoms modifies its electronic structure and optimizes its electrocatalytic reaction kinetics,which significantly enhances its electrical conductivity and structural stability,which are verified by various characterization tools,including X‐ray photoelectron spectroscopy,high‐resolution transmission electron microscopy,X‐ray absorption near‐edge spectroscopy,and extended X‐ray absorption fine structure.Moreover,the hierarchically formed flakes of P‐BMS provide numerous catalytic surface‐active sites,which remarkably enhance its HER activity.The optimized P‐BMS electrocatalysts exhibit low overpotentials(60 and 72 mV at 10 mA cm^(−2))in H_(2)SO_(4)(0.5 M)and KOH(1.0 M),respectively.The mechanism of improving the HER activity of the material was systematically studied using density functional theory calculations and various electrochemical characterization techniques.This study has shown that phase engineering is a promising strategy for enhancing the H*adsorption of metal sulfides.

Research on the Low-carbon Cementitious Materials:Effect of Triisopropanolamine on the Hydration of Phosphorous Slag and Steel Slag

Cement,phosphorous slag(PS),and steel slag(SS)were used to prepare low-carbon cementitious materials,and triisopropanolamine(TIPA)was used to improve the mechanical properties by controlling the hydration process.The experimental results show that,by using 0.06%TIPA,the compressive strength of cement containing 60%PS or 60%SS could be enhanced by 12%or 18%at 28 d.The presence of TIPA significantly affected the hydration process of PS and SS in cement.In the early stage,TIPA accelerated the dissolution of Al in PS,and the formation of carboaluminate hydrate was facilitated,which could induce the hydration;TIPA promoted the dissolution of Fe in SS,and the formation of Fe-monocarbonate,which was precipitated on the surface of SS,resulting in the postponement of hydration,especially for the high SS content.In the later stage,under the continuous solubilization effect of TIPA,the hydration of PS and SS could refine the pore structure.It was noted that compared with portland cement,the carbon emissions of cement-PS-TIPA and cement-SS-TIPA was reduced by 52%and 49%,respectively.

Direct observation of the distribution of impurity in phosphorous/boron co-doped Si nanocrystals

Doping in Si nanocrystals is an interesting topic and directly studying the distribution of dopants in phosphorous/boron co-doping is an important issue facing the scientific community.In this study,atom probe tomography is performed to study the structures and distribution of impurity in phosphorous/boron co-doped Si nanocrystals/SiO_(2) multilayers.Compared with phosphorous singly doped Si nanocrystals,it is interesting to find that the concentration of phosphorous in co-doped samples can be significantly improved.Theoretical simulation suggests that phosphorous-boron pairs are formed in co-doped Si nanocrystals with the lowest formation energy,which also reduces the formation energy of phosphorous in Si nanocrystals.The results indicate that co-doping can promote the entry of phosphorous impurities into the near-surface and inner sites of Si nanocrystals,which provides an interesting way to regulate the electronic and optical properties of Si nanocrystals such as the observed enhancement of conductivity and sub-band light emission.

Intensified reactive extraction of 4-hydroxypyridine with di(2-ethylhexyl) phosphoric acid in 1-octanol by using tributyl phosphate

The efficient separation of amphoteric organic compounds from dilute solutions is of great importance in the industrial field. In the present work, the reactive extractions of 4-hydroxypyridine(4-HP) with tributyl phosphate(TBP), di(2-ethylhexyl) phosphoric acid(D2EHPA) and TBP + D2EHPA dissolved in 1-octanol were investigated, respectively. The influences of the initial concentrations of TBP, D2EHPA and TBP + D2EHPA on distribution ratio(D) were discussed, as well as the reactive extraction mechanism were proposed. The obvious intensification effect was observed when the mixture of TBP and D2EHPA was used as extractant. The best extraction conditions were found to be of the molar ratio of D2EHPA and TBP at 2:1 and the equilibrium aqueous pH at 3.50-4.50. D values increased with the increase of the total concentration of TBP and D2EHPA in 1-octanol. Especially, the analysis on the extraction mechanisms clearly indicate(i) TBP in 1-octanol shows negligible reactive extraction toward 4-HP,(ii) D2EHPA in 1-octanol exhibits moderate extraction effect by forming 4-HP:D2EHPA(1:1) and 4-HP:2D2EHPA(1:2) type complexes, while(iii) D2EHPA in TBP/1-octanol demonstrates the maximum distribution ratio with the 4-HP:D2EHPA(1:1) type complex domination. The discussion provides new insights on the mechanism and opens a new way for the intensified extraction of amphoteric organic compounds by using the mixture of multiple extractants in the diluent.

Enhancing ammonia production rates from electrochemical nitrogen reduction by engineering three-phase boundary with phosphorus-activated Cu catalysts

Electrochemical N_(2) reduction reaction(eNRR) over Cu-based catalysts suffers from an intrinsically low activity of Cu for activation of stable N_(2) molecules and the limited supply of N_(2) to the catalyst due to its low solubility in aqueous electrolytes.Herein,we propose phosphorus-activated Cu electrocatalysts to generate electron-deficient Cu sites on the catalyst surface to promote the adsorption of N_(2) molecules.The eNRR system is further modified using a gas diffusion electrode(GDE) coated with polytetrafluoroethylene(PTFE) to form an effective three-phase boundary of liquid water-gas N_(2)-solid catalyst to facilitate easy access of N_(2) to the catalytic sites.As a result,the new catalyst in the flow-type cell records a Faradaic efficiency of 13.15% and an NH_(3) production rate of 7.69 μg h^(-1) cm^(-2) at-0.2 V_(RHE),which represent 3.56 and 59.2 times increases from those obtained with a pristine Cu electrode in a typical electrolytic cell.This work represents a successful demonstration of dual modification strategies;catalyst modification and N_(2) supplying system engineering,and the results would provide a useful platform for further developments of electrocatalysts and reaction systems.

Structural and Luminescent Properties of Mg_(0.25-x)Al_(2.57)O_(3.79)N_(0.21):xMn^(2+)Green-Emitting Transparent Ceramic Phosphor

A series of spinel-type Mg_(0.25-x)Al_(2.57)O_(3.79)N_(0.21):xMn^(2+)(MgAlON:xMn^(2+))phosphors were synthesized by the solid-state reaction route.The transparent ceramic phosphors were fabricated by pressureless sintering followed by hot-isostatic pressing(HIP).The crystal structure,luminescence and mechanical properties of the samples were systematically investigated.The transparent ceramic phosphors with tetrahedrally coordinated Mn^(2+)show strong green emission centered around 515 nm under blue light excitation.As the Mn^(2+)concentration increases,the crystal lattice expands slightly,resulting in a variation of crystal field and a slight red-shift of green emission peak.Six weak absorption peaks in the transmittance spectra originate from the spin-forbidden ^(4)T_(1)(^(4)G)→^(6)A_(1) transition of Mn^(2+).The decay time was found to decrease from 5.66 to 5.16 ms with the Mn^(2+)concentration.The present study contributes to the systematic understanding of crystal structure and properties of MgAlON:xMn^(2+)green-emitting transparent ceramic phosphor which has a potential application in high-power light-emitting diodes.

Fabrication of YAG:Ce^(3+) and YAG:Ce^(3+),Sc^(3+) Phosphors by Spark Plasma Sintering Technique

In this study,a single-doped phosphors yttrium aluminum garnet(Y_(3)Al_(5)O_(12),YAG):Ce^(3+),single-doped YAG:Sc^(3+),and double-doped phosphors YAG:Ce^(3+),Sc^(3+) were prepared by spark plasma sintering(SPS)(lower than 1 200℃).The characteristics of synthesized phosphors were determined using scanning electron microscopy(SEM),X-ray diffraction(XRD),and fluorescence spectroscopy.During SPS,the lattice structure of YAG was maintained by the added Ce^(3+) and Sc^(3+).The emission wavelength of YAG:Ce^(3+) prepared from SPS(425-700 nm) was wider compared to that of YAG:Ce^(3+) prepared from high-temperature solid-state reaction(HSSR)(500-700 nm).The incorporation of low-dose Sc^(3+) in YAG:Ce^(3+) moved the emission peak towards the short wavelength.

High-performance and robust high-temperature polymer electrolyte membranes with moderate microphase separation by implementation of terphenyl-based polymers

Acid loss and plasticization of phosphoric acid(PA)-doped high-temperature polymer electrolyte membranes(HT-PEMs)are critical limitations to their practical application in fuel cells.To overcome these barriers,poly(terphenyl piperidinium)s constructed from the m-and p-isomers of terphenyl were synthesized to regulate the microstructure of the membrane.Highly rigid p-terphenyl units prompt the formation of moderate PA aggregates,where the ion-pair interaction between piperidinium and biphosphate is reinforced,leading to a reduction in the plasticizing effect.As a result,there are trade-offs between the proton conductivity,mechanical strength,and PA retention of the membranes with varied m/p-isomer ratios.The designed PA-doped PTP-20m membrane exhibits superior ionic conductivity,good mechanical strength,and excellent PA retention over a wide range of temperature(80–160°C)as well as satisfactory resistance to harsh accelerated aging tests.As a result,the membrane presents a desirable combination of performance(1.462 W cm^(-2) under the H_(2)/O_(2)condition,which is 1.5 times higher than that of PBI-based membrane)and durability(300 h at 160°C and 0.2 A cm^(-2))in the fuel cell.The results of this study provide new insights that will guide molecular design from the perspective of microstructure to improve the performance and robustness of HT-PEMs.

Death from caustic ingestion:A case report

Rationale:Acute caustic ingestion from suicidal intent is not usual in emergency departments in developed countries.One of the substances commonly ingested by suicidal patients,phosphoric acid,tends to cause multi-system derangements.Patient’s Concern:A 41-year-old male patient presented with complaints of throat discomfort,severe generalized abdominal pain,and multiple episodes of hematemesis after ingesting a restroom cleaning solution.Diagnosis:Poisoning by acute caustic ingestion(containing<30%phosphoric acid and<4%ethylene glycol).Interventions:The patient was administered 50 mL of 8.4%sodium bicarbonate solution followed by an isotonic sodium bicarbonate solution running at 500 mL/h,a hyperkalemia kit,ceftriaxone,metronidazole,omeprazole,and atropine.The patient then underwent urgent hemodialysis.Outcomes:The patient suffered gastrointestinal bleeding as a result of local caustic injury.In addition,his course of illness was complicated by severe acidemia from high anion gap metabolic acidosis and deranged electrolytes(hyperphosphatemia,hyperkalemia,and hypocalcemia).He developed multi-organ failure and eventually demised.Lessons:The clinician needs to be mindful of the multi-system complications arising from such a caustic ingestion.These patients need to be monitored closely for deterioration,and have prompt management of the various arising complications,to reduce the high morbidity and mortality associated with this condition.

Cemented backfilling performance of yellow phosphorus slag

The experiments on the cemented backfilling perfbrmance of yellow phosphorus slag, including physical-mechanical properties, chemical compositions, optimized proportion, and cementation mechanisms, were carried out to make good use of yellow phosphorus slag as well as tackle with environment problems, safety problems, geological hazards, and high-cost issues during mining in Kaiyang Phosphorus Mine Group, Guizhou. The results show that yellow phosphorus slag can be used as the cement substitute for potential coagulation property. Quicklime, hydrated lime, and other alkaline substances can eliminate the high residual phosphorus to improve the initial strength of backfilling body. The recommended proportions （mass ratio） are 1：1 （yellow phosphorus slag：phosphorous gypsum）, 1：4：10 （Portland cement：yellow phosphorus slag：phosphorous gypsum）, and 1：4：10 （ultra fine powder：yellow phosphorus slag：phosphorous gypsum） with 5wt% of hydrated lime addition, 60wt% of solid materials, no fly ash addition, and good rheological properties. The hydration reaction involves hydration stage, solidifying stage, and strength stage with Ca（OH）2 as the activating agent. The reaction rates of yellow phosphorus slag, Portland cement, and ultrafine powder hydration with the increase of microstructure stability and initial strength.

Synthesis of Ce:YAG Phosphor via Homogeneous Precipitation under Microwave Irradiation

Ultra-fine Ce:YAG phosphors were prepared by homogeneous precipitation under microwave irradiation method . The formation of Ce: YAG was investigated by means of XRD and DTA/TG. The purified YAG crystallized phase was obtained at a lower temperature (1100℃). Basically spherical Ce:YAG powders were indicated from TEM images, and the size of the particles is about 80 nm. Two peaks of 436 and 473 nm can be seen from the excitation spectrum in the range of 402 -510 nm. A broad emission band located at 480 ~ 630 nm shows the phosphors prepared by this method have good emission properties.

Arsenic removal from contaminated soil using phosphoric acid and phosphate

Laboratory batch experiments were conducted to study arsenic （As） removal from a naturally contaminated soil using phosphoric acid （H3PO4） and potassium dihydrogen phosphate （KHEPO4）. Both H3PO4 and KHEPO4 proved to reduce toxicity of the soil in terms of soil As content, attaining more than 20% As removal at a concentration of 200 mmol/L. At the same time, acidification of soil and dissolution of soil components （Ca, Mg, and Si） resulted from using these two extractants, especially H3PO4. The effectiveness of these two extractants could be attributed to the replacement of As by phosphate ions （PO4^3-）. The function of H3PO4 as an acid to dissolve soil components had little effects on As removal. KH2PO4 almost removed as much As as H3PO4, but it did not result in serious damage to soils, indicating that it was a more promising extractant. The results of a kinetic study showed that As removal reached equilibrium after incubation for 360 rain, but dissolution of soil components, especially Mg and Ca, was very rapid. Therefore dissolution of soil components would be inevitable if As was further removed. Elovich model best described the kinetic data of As removal among the four models used in the kinetic study.

Researches on the Treatment of Phosphorous Wastewater with Oyster Shells

Based on the analysis of adsorptive features of oyster shells,the researches on the treatment of phosphorous wastewater with oyster shells and the effect of temperature on phosphorus removal were carried out.XRD was used to characterize the crystalline phases,and the main component of oyster shells was shown to be CaCO3.When the pretreatment temperature reached 800 ℃,some CaCO3 decomposed into CaO.As the temperature was further raised,CaO increased gradually.Via SEM testing,the oyster shell was a kind of natural porous materials.The pore wall partially collapsed from 550 to 900 ℃.No obvious porous structure was found at 900 ℃.However,without preheating,the oyster shell phosphorous removal material can not adsorb the phosphorus.Pretreatment made calcium activate,thus greatly increasing the absorption of phosphorus.

Denitrifying phosphorous removal in anaerobic/anoxic SBR system with different startup operation mode

To achieve stable and efficient nitrogen and phosphorus removal and to investigate the characteristics of the A/A SBR enriched with denitrifying phosphorus removal bacteria(DPB),the whole course of startup was studied with two reactors operated in different mode.The reactor I was operated under anaerobic/settling/anoxic/settling mode,and the reactor II was operated under anaerobic/anoxic/settling mode.Differences between the two reactors in removal efficiency of COD,nitrogen and phosphorus were examined.The results indicated that efficient performance could be achieved in both reactors with different startup operation mode,while the phosphorus removal efficiency was improved sooner in reactor I than in reactor II,which suggested that reactor I would supply a more favorable condition for DPB proliferation.Meanwhile,it was observed that the amount of organic substrates consumption had a linear correlation to that of phosphorus release in anaerobic phase when DPB was accumulated in the A/A SBR denitrifying phosphorus removal system.

Adsorption equilibrium and kinetics studies of divalent manganese from phosphoric acid solution by using cationic exchange resin

There are numerous impurities in wet-process phosphoric acid,among which manganese is one of detrimental metallic impurities,and it causes striking negative effects on the industrial phosphoric acid production and downstream commodity.This article investigated the adsorption behavior of manganese from phosphoric acid employing Sinco-430 cationic ion-exchange resin.Resorting FT-IR and XPS characterizations,the adsorption mechanism was proved to be that manganese was combined with sulfonic acid group.Several crucial parameters such as temperature,phosphoric acid content and resin dose were studied to optimize adsorption efficiency.Through optimization,removal percentage and sorption capacity of manganese reached 53.12 wt%,28.34 mg·g^-1,respectively.Pseudo-2nd-order kinetic model simulated kinetics data best and the activation energy was evaluated as 6.34 kJ·mol^-1 for the sorption reaction of manganese.In addition,the global adsorption rate was first controlled by film diffusion process and second determined by pore diffusion process.It was found that the resin could adsorb up to 50.24 mg·g^-1 for manganese.Equilibrium studies showed that Toth adsorption isotherm model fitted best,followed by Temkin and Langmuir adsorption isotherm models.Thermodynamic analysis showed that manganese adsorption was an endothermic process with enhanced randomness and spontaneity.

Synthesis and Characterization of Cerium-Doped Lutetium Aluminum Garnet Phosphors by Nitrate-citrate Sol-Gel Combustion Process

Nanosized cerium-doped lutetium aluminum garnet （LuAG：Ce） phosphors were prepared by nitrate-citrate solgel combustion process using 1：1 ratio of the citrate：nitrate. The prepared LuAG：Ce phosphors were characterized by XRD, TEM, photoluminescence and radioluminescence spectra excited by UV and X-ray, respectively. The purified crystalline phase of LuAG：Ce was obtained at 900 ℃ by directly crystallizing from amorphous materials. The resultant Lu- AG：Ce phosphors were uniform and had good dispersivity with an average particle size of about 30 urn. Both photoluminescence and radioluminescence were well-known Ce^3＋ emissions located in the range of 470 -600 nm consisting of two emission bands because of the transition from the lowest 5d excited state （2D） to the 4f ground state of Ce^3＋, which matched well with the sensitivity curve of the Si-photodiode. There was a little red shift for the emission components from the UV-excited emission spectrum to the X-ray-excited emission spectrum. The fast scintillation decay component of 26 ns satisfies the requirements of fast scintillators.

Separation of Indium and Iron from Dilute Sulphate Solutions with a Phosphorous Mixer Extractant

The phosphorous mixer introduced could replace D2EHPA as an extractant applied in the extraction of indium. The extraction properties of the phosphorous mixer were studied. The influences of extractant concentration, organic/aqueous (O/A) phase ratio, equilibrium time, and pH value of the feed solutions on the extraction of indium, and separation of indium-iron were investigated experimentally. Under the best operating conditions, more than 98% of indium. was extracted through two-stage counter-current extraction. The optimizing condition of indium extraction is determined as follows: O/A = 1 : (9-12) in volume ratio; 30% PPD in sulphonated kerosene; pH of the feed, about 0.6; equilibrium time, 3-5 min. The extractant has good reusing and anti-aging properties.

A Blended Cement Containing Blast Furnace Slag and Phosphorous Slag

Blended cement containing blast furnace slag (BFS) and phosphorous slag( PS) is a new kind of cement. The total content of blended materials could increase if two additives were used. Using the same admixtures , the properties of the blended cement with 70% additives could reach the standard of 525-grade slag cement according to GB. The strength of cement with 80% additives could reach the standard of 425-grade slag cement. The tests of strength, pore structure, hydration products, inhibiting alkali-aggregate reaction, resistance to sulfate corrosion of BFS-PSC were performed.