The efficient separation of amphoteric organic compounds from dilute solutions is of great importance in the industrial field. In the present work, the reactive extractions of 4-hydroxypyridine(4-HP) with tributyl pho...The efficient separation of amphoteric organic compounds from dilute solutions is of great importance in the industrial field. In the present work, the reactive extractions of 4-hydroxypyridine(4-HP) with tributyl phosphate(TBP), di(2-ethylhexyl) phosphoric acid(D2EHPA) and TBP + D2EHPA dissolved in 1-octanol were investigated, respectively. The influences of the initial concentrations of TBP, D2EHPA and TBP + D2EHPA on distribution ratio(D) were discussed, as well as the reactive extraction mechanism were proposed. The obvious intensification effect was observed when the mixture of TBP and D2EHPA was used as extractant. The best extraction conditions were found to be of the molar ratio of D2EHPA and TBP at 2:1 and the equilibrium aqueous pH at 3.50-4.50. D values increased with the increase of the total concentration of TBP and D2EHPA in 1-octanol. Especially, the analysis on the extraction mechanisms clearly indicate(i) TBP in 1-octanol shows negligible reactive extraction toward 4-HP,(ii) D2EHPA in 1-octanol exhibits moderate extraction effect by forming 4-HP:D2EHPA(1:1) and 4-HP:2D2EHPA(1:2) type complexes, while(iii) D2EHPA in TBP/1-octanol demonstrates the maximum distribution ratio with the 4-HP:D2EHPA(1:1) type complex domination. The discussion provides new insights on the mechanism and opens a new way for the intensified extraction of amphoteric organic compounds by using the mixture of multiple extractants in the diluent.展开更多
Phosphorite ore is a potential resource of rare earths (RE) as well as phosphate; therefore, the recovery of RE from wet-process phosphoric acid (WPA) is promising. This study investigated the influence of rotatio...Phosphorite ore is a potential resource of rare earths (RE) as well as phosphate; therefore, the recovery of RE from wet-process phosphoric acid (WPA) is promising. This study investigated the influence of rotational speed, extractant concentration, flow ratio and phase contact time on the centrifugal extraction of RE from WPA and the separation of RE from impurities. The results indicate that higher rotational speed, higher extractant concentration and larger flow ratio are beneficial to the extraction of RE and impurities from phosphoric acid. It is found that the phase contact time for efficiently extracting RE and that for iron are of great difference, which provides an effective method for separating RE from iron using the non-equilibrium extraction process in centrifugal contactors. Compared with equilibrium extraction, the separation factor βRE/Fe is enhanced from 0.07 to 17.6.展开更多
Desupersaturation is a complex cooling operation that involves hydrodynamic,thermal and mechanical phenomena.This process requires continuous agitation to avoid fouling problems and sludge deposition.The current work ...Desupersaturation is a complex cooling operation that involves hydrodynamic,thermal and mechanical phenomena.This process requires continuous agitation to avoid fouling problems and sludge deposition.The current work aims to investigate the well mixedness in the desupersaturation tank for optimal performance.For this purpose,a multi-fluid CFD study was conducted based on the Euler–Euler modeling approach,considering a multiphase flow involving a liquid phase(phosphoric acid)and a poly-dispersed solid phase,i.e.a sludge with three different sizes where each size is considered as a separate phase.First,the hydrodynamic behavior of the flow within the agitated desupersaturator is analyzed through the investigation of the velocity fields as well as the power and pumping numbers,to determine both the agitator capacity to pump the flow and its power consumption during the operation.Then,in order to assess the mixture homogeneity,we evaluated the solid suspension in the desupersaturation reactor following conventional methods and two new proposed methodologies:the first approach is to evaluate the suspension quality in the mixing system by compartment and the second consists on the assessment of the uniform convergence of the solid concentration.Furthermore,we calculated the time required to achieve a full suspension at different solid concentrations.On other hand,we conducted a detailed analysis of the solid distribution dependency on the impeller rotational speed at different solid volume fraction,which allows a good understanding of the parameters controlling the homogenization in the desupersaturator.展开更多
Iron element is one of the main impurities in wet-process phosphoric acid and it has a significant impact on the subsequent phosphorus chemical products. This paper studied the feasibility of using Sinco-430 cation ex...Iron element is one of the main impurities in wet-process phosphoric acid and it has a significant impact on the subsequent phosphorus chemical products. This paper studied the feasibility of using Sinco-430 cation exchange resin for iron removal from phosphoric acid. The specific surface area and the total exchange capacity of resin were 8.91 m2·g-1 and 5.18 mmol·g-1, respectively. The sorption mechanism was determined by FTIR and XPS and the results indicated that iron was combined with-SO3 H in resin. The removal process was studied as a function of temperature, H3 PO4 content and mass ratio between resin and solution. The unit mass of resin to remove iron was 0.058 g·g-1 resin when the operating parameters were T = 50 ℃, H3 PO4 content = 27.61 wt%and S/L = 0.1, respectively. Kinetics study demonstrated that pseudo-second-order reaction model fits this study best and the calculated activation energy of overall reaction is 29.10 kJ·mol-1. The overall reaction process was mainly controlled by pore diffusion.展开更多
Laboratory batch experiments were conducted to study arsenic (As) removal from a naturally contaminated soil using phosphoric acid (H3PO4) and potassium dihydrogen phosphate (KHEPO4). Both H3PO4 and KHEPO4 prove...Laboratory batch experiments were conducted to study arsenic (As) removal from a naturally contaminated soil using phosphoric acid (H3PO4) and potassium dihydrogen phosphate (KHEPO4). Both H3PO4 and KHEPO4 proved to reduce toxicity of the soil in terms of soil As content, attaining more than 20% As removal at a concentration of 200 mmol/L. At the same time, acidification of soil and dissolution of soil components (Ca, Mg, and Si) resulted from using these two extractants, especially H3PO4. The effectiveness of these two extractants could be attributed to the replacement of As by phosphate ions (PO4^3-). The function of H3PO4 as an acid to dissolve soil components had little effects on As removal. KH2PO4 almost removed as much As as H3PO4, but it did not result in serious damage to soils, indicating that it was a more promising extractant. The results of a kinetic study showed that As removal reached equilibrium after incubation for 360 rain, but dissolution of soil components, especially Mg and Ca, was very rapid. Therefore dissolution of soil components would be inevitable if As was further removed. Elovich model best described the kinetic data of As removal among the four models used in the kinetic study.展开更多
The extraction of Nd^3+ and Sm^3+, including the extraction and stripping capability as well as the separation effect of Nd^3+ or Sm^3+, from a sulfuric acid medium, by mixtures of di-(2-ethylhexyl) phosphoric a...The extraction of Nd^3+ and Sm^3+, including the extraction and stripping capability as well as the separation effect of Nd^3+ or Sm^3+, from a sulfuric acid medium, by mixtures of di-(2-ethylhexyl) phosphoric acid (HDEHP, H2A2(0)) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (HEH/EHP, H2L2(0)) were studied. The distribution ratios and synergistic coefficients of Nd^3+ and Sm^3+ in different acidities were also determined. A synergistic extractive effect was found when HDEHP and HEH/EHP were used as mixed extractants for Sm^3+ or Nd^3+. The chemical compositions of the extracted complex were determined as Nd.(HA2)2-HL2 and Sm.(HA2)2-HL2. The extraction equilibrium constants, enthalpy change, and entropy change of the extraction reaction were also determined.展开更多
The catalytic fast pyrolysis of cellulose impregnated with phosphoric acid (H3PO4) offers a promising method for the selective production of levoglucosenone (LGO),a valuable anhydrosugar product.However,the fundamenta...The catalytic fast pyrolysis of cellulose impregnated with phosphoric acid (H3PO4) offers a promising method for the selective production of levoglucosenone (LGO),a valuable anhydrosugar product.However,the fundamental mechanism for selective LGO formation is unclear.Herein,quantum chemistry calculations and catalytic fast pyrolysis experiments were performed to reveal the formation mechanism of LGO in H3PO4-catalyzed cellulose pyrolysis.H3PO4 significantly decreased the energy barriers of the pyrolytic reactions and altered the competitiveness of the LGO formation pathways,promoting LGO formation.Through different pathways in the non-catalytic and H3P04-catalyzed conditions,LGO is mainly produced from the primary decomposition of glucose units of cellulose and secondary conversion of levoglucosan.The major catalytic formation pathways of LGO comprise similar reactions,with dehydration at the 3-OH+2-H site as the rate-determining step.Importantly,secondary conversion of 1,4;3,6-dianhydro-α-D-glucopyranose is not feasible for LGO formation,in contrast to previous reports.In addition,a high degree of polymerization is beneficial for the selectivity of LGO formation in the catalytic process,because the glycosidic bond is important for the formation of the bicyclic structure (1,5-and1,6-acetal rings).展开更多
There are numerous impurities in wet-process phosphoric acid,among which manganese is one of detrimental metallic impurities,and it causes striking negative effects on the industrial phosphoric acid production and dow...There are numerous impurities in wet-process phosphoric acid,among which manganese is one of detrimental metallic impurities,and it causes striking negative effects on the industrial phosphoric acid production and downstream commodity.This article investigated the adsorption behavior of manganese from phosphoric acid employing Sinco-430 cationic ion-exchange resin.Resorting FT-IR and XPS characterizations,the adsorption mechanism was proved to be that manganese was combined with sulfonic acid group.Several crucial parameters such as temperature,phosphoric acid content and resin dose were studied to optimize adsorption efficiency.Through optimization,removal percentage and sorption capacity of manganese reached 53.12 wt%,28.34 mg·g^-1,respectively.Pseudo-2nd-order kinetic model simulated kinetics data best and the activation energy was evaluated as 6.34 kJ·mol^-1 for the sorption reaction of manganese.In addition,the global adsorption rate was first controlled by film diffusion process and second determined by pore diffusion process.It was found that the resin could adsorb up to 50.24 mg·g^-1 for manganese.Equilibrium studies showed that Toth adsorption isotherm model fitted best,followed by Temkin and Langmuir adsorption isotherm models.Thermodynamic analysis showed that manganese adsorption was an endothermic process with enhanced randomness and spontaneity.展开更多
Kiln phosphoric acid(KPA)technology could produce P2O5 with high purity and has been applied in thermal phosphoric acid industry;however the formation of fouling in the high-temperature rotary kiln restricts the stabl...Kiln phosphoric acid(KPA)technology could produce P2O5 with high purity and has been applied in thermal phosphoric acid industry;however the formation of fouling in the high-temperature rotary kiln restricts the stable and long-term operation.In this paper,the reaction of phosphate ores with gaseous P2O5 was investigated in a high-temperature reactor,and the Ca O-SiO2-P2O5 ternary phase diagram was analyzed to understand the fouling formation mechanism.The results showed that the low-melting-point products,such as Ca(PO3)2and Ca2P2O7,are responsible for the fouling in the KPA process.In addition,a small amount of impurities,e.g.,aluminum and iron,could facilitate the generation of the low-melting-point products and cause serious fouling.Based on the high-temperature SiO2-P2O5 and CaO-SiO2-P2O5 phase diagram analysis,the control of Si/Ca molar ratio(e.g.,Si/Ca=2.0)was found to avoid fouling formation in the kiln.These results could provide the operation parameters of reaction temperature and feeds composition to suppress the fouling in the kiln reactor for the phosphoric acid production in industry.展开更多
As the world's population exponentially grows,so does the need for the production of food,with cereal production growing annually from an estimated 1.0 billion to 2.5 billion tons within the last few decades.This ...As the world's population exponentially grows,so does the need for the production of food,with cereal production growing annually from an estimated 1.0 billion to 2.5 billion tons within the last few decades.This rapid growth in food production results in an ever increasing amount of agricultural wastes,of which already occupies nearly 50%of the total landfill area.For example,is the billions of dry tons of cellulose-containing spent coffee grounds disposed in landfills annually.This paper seeks to provide a method for isolating cellulose nanocrystals(CNCs)from spent coffee grounds,in order to recycle and utilize the cellulosic waste material which would otherwise have no applications.CNCs have already been shown to have vast applications in the polymer engineering field,mainly utilized for their high strength to weight ratio for reinforcement of polymer-based nanocomposites.A successful method of purifying and hydrolyzing the spent coffee grounds in order to isolate usable CNCs was established.The CNCs were then characterized using current techniques to determine important chemical and physical properties.A few crucial properties determined were aspect ratio of 12±3,crystallinity of 74.2%,surface charge density of(48.4±6.2)mM/kg cellulose,and the ability to successfully reinforce a polymer based nanocomposite.These characteristics compare well to other literature data and common commercial sources of CNCs.展开更多
A continuous melt suspension crystallization process has been presented for the purification of the phosphoric acid in this study, which is performed in the cascade of a mixed suspension mixed product removal (MSMPR) ...A continuous melt suspension crystallization process has been presented for the purification of the phosphoric acid in this study, which is performed in the cascade of a mixed suspension mixed product removal (MSMPR) crystallizer and a gravity wash column for the subsequent solid-liquid separation. Dynamic behavior in the crystallizer and role of reflux ration on the purification efficiency of column are studied in detail. A reasonable steady state with respect to the liquid phase is achieved after 2 to 3 hrs, which is followed by a solid-phase steady state in terms of the slurry density after 4 hrs. Reflux ratio is the effective parameter for separation and purification by the crystallization equipment from the influences of reflux ratio on the purity of product, the number of theoretical plates and the stability of the operations.展开更多
In a rotary kiln process for phosphoric acid production,the reaction between gaseous phosphorus pentoxide(P_2O_5)and phosphate ore and silica contained in feed balls(the so-called P_2O_5"absorption")not only...In a rotary kiln process for phosphoric acid production,the reaction between gaseous phosphorus pentoxide(P_2O_5)and phosphate ore and silica contained in feed balls(the so-called P_2O_5"absorption")not only reduces phosphorous recovery but also generates a large amount of low melting-point side products.The products may give rise to formation of kiln ring,which interferes with kiln operation performance.In this study,the reactions of gaseous P_2O_5with solid calcium phosphate(Ca_3(PO_4)_2),silica(SiO_2)and their mixture,respectively,were investigated via combined chemical analysis and various characterizations comprised of X-ray diffraction(XRD),Fourier-transform infrared(FT-IR)spectroscopy,thermogravimetric analysis and differential scanning calorimeter(TG&DSC),and scanning electron microscopy and energy dispersive spectrometer(SEM&EDS).Attentions were focused on apparent morphology,phase transformation and thermal stability of the products of the P_2O_5"absorption"at different temperatures.The results show that the temperature significantly affected the"absorption".The reaction between pure Ca_3(PO_4)_2 and P_2O_5 occurred at 500°C.Calcium metaphosphate(Ca(PO_3)_2)was the primary product at the temperatures≤900°C with its melting point≤900°C while calcium pyrophosphate(Ca_2P_2O_7)was obtained over 1000°C,which has a melting point≤1200°C.The"absorption"by pure SiO_2 started at 800°C and the most significant reaction occurred at 1000°C with formation of silicon pyrophosphate(SiP_2O_7)product of melting point≤1000°C.Using mixed Ca_3(PO_4)_2and SiO_2as raw material,the"absorption"by Ca_3(PO_4)_2 was enhanced due to existence of silica.At 600–700°C,silica was inert to P_2O_5and thus formed a porous structure in the raw material,which accelerated diffusion of gaseous P_2O_5inside the mixture.At higher temperatures,the combined"absorption"by calcium phosphate and reaction between silicon dioxide and the"absorption"product calcium pyrophosphate,reinforced the"absorption"by the mixture.Besides,it was found that both Ca(PO_3)_2and SiP_2O_7were unstable at high temperatures and would decompose to Ca_2P_2O_7and SiO_2,respectively,at over 1000°C and 1100°C with the release of gaseous P_2O_5at the same time.展开更多
The dry modification of aluminum hydroxide powders with phosphoric acid and the effects of modification of technological conditions on thermal stability, morphology and oil absorption of aluminum hydroxide powders wer...The dry modification of aluminum hydroxide powders with phosphoric acid and the effects of modification of technological conditions on thermal stability, morphology and oil absorption of aluminum hydroxide powders were investigated. The results show that the increase of mass ratio of phosphoric acid to aluminum hydroxide, the decrease of mass concentration of phosphoric acid and prolongation of mixing time are favorable to the improvement of thermal stability of aluminum hydroxide; when the mass ratio of phosphoric acid to aluminum hydroxide is 5:100, the mass concentration of phosphoric acid is 200 g/L and the mixing time is 10 min, the initial temperature of loss of crystal water in aluminum hydroxide rises from about 192.10 to 208.66 ℃, but the dry modification results in the appearance of agglomeration and macro-aggregate in the modified powders, and the oil absorption of modified powders becomes higher than that of original aluminum hydroxide.展开更多
Corrosion studies of a commercially pure titanium in phosphoric acid solutions at 250 ℃ were carried out by immersion test in an autoclave. At lower phosphoric acid concentration (0.1 mol/L), the corrosion was mild. ...Corrosion studies of a commercially pure titanium in phosphoric acid solutions at 250 ℃ were carried out by immersion test in an autoclave. At lower phosphoric acid concentration (0.1 mol/L), the corrosion was mild. At higher phosphoric concentration (1.0 mol/L) corrosion, a 25 μm-thick white corrosion products layer was formed on the samples after 24 h immersion. XRD analysis shows that the white layer consists mainly of titanium oxide phosphate hydrate (π-Ti2O(PO4)2·2H2O). The corrosion product shows the morphology of fiber bundles. A thermodynamic analysis of the formation of the corrosion product is presented.展开更多
The rheological behavior of phosphoric acid-water glass grout in different mixing ratios was studied. Grout made of water glass with Baume degree of 20° and 13.4% phosphoric acid by 1:1 volume ratio is found to b...The rheological behavior of phosphoric acid-water glass grout in different mixing ratios was studied. Grout made of water glass with Baume degree of 20° and 13.4% phosphoric acid by 1:1 volume ratio is found to be more effective in stopping water. Laboratory model test of water shutoff by grouting was conducted. Test results show that the diffusion length and water cutoff effect of the grout are significantly improved as the grout head is raised, due to the dilution of underground water, and it takes the grout longer than its gel time to cut off water.展开更多
There exists the most important REE-bearing phosphorite deposit in Southwest of China. Due to the fact that the REE are present in the form of ions in the lattices of collophanite or carbonatfluorapatite, the REE can ...There exists the most important REE-bearing phosphorite deposit in Southwest of China. Due to the fact that the REE are present in the form of ions in the lattices of collophanite or carbonatfluorapatite, the REE can be enriched in phosphate concentrate by flotation method. The phosphate concentrate is the main raw materials to produce phosphoric acid, therefore, it is significant to further investigate the distribution rule of REE in wet process. In this paper, the single leaching and recycled leaching technology were carried out to investigate the effect of various parameter conditions on distribution of REE in products. The REE compositions of products were analyzed by Inductively Coupled Plasma Emission Mass Spectrometry (ICP-MS) method. It was found that the acidic value of leaching liquor was the main effect factor on the distribution of REE in products. In single leaching stage, P2O5 concentration of leaching liquor slightly varied from 8% to about 10% when the excessive coefficient of sulphuric acid ranged from 1.03 to 1.05, and the distribution proportions of ∑REO in phosphoric acid solution was lower than 40%. However, in recycled leaching process(the condition similar to practical wet process), with an increase of P2O5 concentration as well as the acidic value of leaching liquor, the distribution proportions of ∑REO in phosphoric acid solution could be decreased to 2.56%. That is to say that under the condition similar to practical wet process, more than 90% of REE of phosphate concentrate became precipitation entering into the phosphogypsum product. This investigation will provide valid reference for reasonably recovering or reserving REE in wet-phosphoric acid process.展开更多
Chiral amino cyclic phosphoric acids, 5-amino-2-hydroxy-4-(4-nitrophenyl)-1,3,2-dioxaphosphorinane 2-oxide and 2-hydroxy-4-(4-methylsulfonylphenyl)-5-phthalimido-1,3,2-dioxaphos phorinane 2-oxide are synthesized in go...Chiral amino cyclic phosphoric acids, 5-amino-2-hydroxy-4-(4-nitrophenyl)-1,3,2-dioxaphosphorinane 2-oxide and 2-hydroxy-4-(4-methylsulfonylphenyl)-5-phthalimido-1,3,2-dioxaphos phorinane 2-oxide are synthesized in good over yields (64.2%and 72.8%respectively) from 2-amino-1-aryl-1,3-propanediols. The different reaction conditions are necessary in hydrolysis reactions of amino cyclic phosphonyl chlorides.展开更多
A hybrid system that consists of a phosphoric acid fuel cell(PAFC),an absorption refrigerator and a refrigeration-space is proposed.The four-heat-source absorption refrigerator,which is driven by the waste heat produc...A hybrid system that consists of a phosphoric acid fuel cell(PAFC),an absorption refrigerator and a refrigeration-space is proposed.The four-heat-source absorption refrigerator,which is driven by the waste heat produced from PAFC,provides cooling for a refrigeration-space.A numerical model is set up to analyze both the steady-state performance and transient performance considering the influences of the electrochemical and thermodynamic irreversibilities.Expressions of the equivalent power output and efficiency of the hybrid system are determined.Moreover,the transient behavior of cold-space temperature is performed and the time to reach a prescribed cold-space temperature is displayed.Thus,the operation regions of the current are optimized at different operating conditions.The results showthat in an appropriate current range,the overall power output and efficiencies of the hybrid system are enhanced.展开更多
Cellulose,being as the most abundant nature polymer material and the most promising oil substitute,attracts more and more interests.A new cellulose dissolution system,phosphoric acid(PA)/polyphosphoric acid(PPA) solve...Cellulose,being as the most abundant nature polymer material and the most promising oil substitute,attracts more and more interests.A new cellulose dissolution system,phosphoric acid(PA)/polyphosphoric acid(PPA) solvent,was investigated in this study.It had been found that a larger cellulose solid content could be dissolved quickly in a hypothermic situation.By evaluating the stability of regenerated cellulose film and the formation of anisotropic solution,the dissolution behavior of cellulose was investigated.Wide-angle X-ray diffraction(WAXD) and Fourier transform infrared spectroscopy(FT-IR) were employed to characterize the crystalline structure and morphology of regenerated cellulose.The measurement results revealed a transition from cellulose-Ⅰ of raw cellulose to cellulose-Ⅱ of regenerated cellulose and a decrease of crystallinity of cellulose after dissolved.This was attributed to the interaction between cellulose and acid solvent,which leaded to the breakage of cellulose intra-and inter-molecule hydrogen bonds and the conformation change of cellulose C6-OH.Moreover,the formation process of cellulose liquid crystal solution was illustrated by polarized light microscope(PLM).That may be induced by the rearranging movement of the cellulose macromolecular chains.展开更多
In order to study the effect of fused spinel on the properties of phosphoricacid bonded high alumina castables, samples with different contents of fused spinel were prepared.The results show that when the contents of ...In order to study the effect of fused spinel on the properties of phosphoricacid bonded high alumina castables, samples with different contents of fused spinel were prepared.The results show that when the contents of the fused spinel are between 8% and 16% (mass fraction),the castables have good properties. The castables overcome the shortages of the phosphoric acidbonded high alumina castables with bauxite cement as a hardening promoter. The experimentsdemonstrate that most of the service properties of the castables with fused spinel are better thanthose of the normal phosphoric acid bonded castables which use bauxite cement as a hardeningpromoter. The examination of the materials indicates that free MgO inclusions in the spinel powdercan promote the hardening of the castables.展开更多
基金supported by the Science and Technology Research Project of Henan Province (192102310490 and 212102310505)。
文摘The efficient separation of amphoteric organic compounds from dilute solutions is of great importance in the industrial field. In the present work, the reactive extractions of 4-hydroxypyridine(4-HP) with tributyl phosphate(TBP), di(2-ethylhexyl) phosphoric acid(D2EHPA) and TBP + D2EHPA dissolved in 1-octanol were investigated, respectively. The influences of the initial concentrations of TBP, D2EHPA and TBP + D2EHPA on distribution ratio(D) were discussed, as well as the reactive extraction mechanism were proposed. The obvious intensification effect was observed when the mixture of TBP and D2EHPA was used as extractant. The best extraction conditions were found to be of the molar ratio of D2EHPA and TBP at 2:1 and the equilibrium aqueous pH at 3.50-4.50. D values increased with the increase of the total concentration of TBP and D2EHPA in 1-octanol. Especially, the analysis on the extraction mechanisms clearly indicate(i) TBP in 1-octanol shows negligible reactive extraction toward 4-HP,(ii) D2EHPA in 1-octanol exhibits moderate extraction effect by forming 4-HP:D2EHPA(1:1) and 4-HP:2D2EHPA(1:2) type complexes, while(iii) D2EHPA in TBP/1-octanol demonstrates the maximum distribution ratio with the 4-HP:D2EHPA(1:1) type complex domination. The discussion provides new insights on the mechanism and opens a new way for the intensified extraction of amphoteric organic compounds by using the mixture of multiple extractants in the diluent.
基金the National High Technology Research and Development Program of China (No.2006AA06Z126) for the financial aid
文摘Phosphorite ore is a potential resource of rare earths (RE) as well as phosphate; therefore, the recovery of RE from wet-process phosphoric acid (WPA) is promising. This study investigated the influence of rotational speed, extractant concentration, flow ratio and phase contact time on the centrifugal extraction of RE from WPA and the separation of RE from impurities. The results indicate that higher rotational speed, higher extractant concentration and larger flow ratio are beneficial to the extraction of RE and impurities from phosphoric acid. It is found that the phase contact time for efficiently extracting RE and that for iron are of great difference, which provides an effective method for separating RE from iron using the non-equilibrium extraction process in centrifugal contactors. Compared with equilibrium extraction, the separation factor βRE/Fe is enhanced from 0.07 to 17.6.
文摘Desupersaturation is a complex cooling operation that involves hydrodynamic,thermal and mechanical phenomena.This process requires continuous agitation to avoid fouling problems and sludge deposition.The current work aims to investigate the well mixedness in the desupersaturation tank for optimal performance.For this purpose,a multi-fluid CFD study was conducted based on the Euler–Euler modeling approach,considering a multiphase flow involving a liquid phase(phosphoric acid)and a poly-dispersed solid phase,i.e.a sludge with three different sizes where each size is considered as a separate phase.First,the hydrodynamic behavior of the flow within the agitated desupersaturator is analyzed through the investigation of the velocity fields as well as the power and pumping numbers,to determine both the agitator capacity to pump the flow and its power consumption during the operation.Then,in order to assess the mixture homogeneity,we evaluated the solid suspension in the desupersaturation reactor following conventional methods and two new proposed methodologies:the first approach is to evaluate the suspension quality in the mixing system by compartment and the second consists on the assessment of the uniform convergence of the solid concentration.Furthermore,we calculated the time required to achieve a full suspension at different solid concentrations.On other hand,we conducted a detailed analysis of the solid distribution dependency on the impeller rotational speed at different solid volume fraction,which allows a good understanding of the parameters controlling the homogenization in the desupersaturator.
基金Supported by the National Basic Research Program of China(2016YFD0200404)
文摘Iron element is one of the main impurities in wet-process phosphoric acid and it has a significant impact on the subsequent phosphorus chemical products. This paper studied the feasibility of using Sinco-430 cation exchange resin for iron removal from phosphoric acid. The specific surface area and the total exchange capacity of resin were 8.91 m2·g-1 and 5.18 mmol·g-1, respectively. The sorption mechanism was determined by FTIR and XPS and the results indicated that iron was combined with-SO3 H in resin. The removal process was studied as a function of temperature, H3 PO4 content and mass ratio between resin and solution. The unit mass of resin to remove iron was 0.058 g·g-1 resin when the operating parameters were T = 50 ℃, H3 PO4 content = 27.61 wt%and S/L = 0.1, respectively. Kinetics study demonstrated that pseudo-second-order reaction model fits this study best and the calculated activation energy of overall reaction is 29.10 kJ·mol-1. The overall reaction process was mainly controlled by pore diffusion.
基金This work was supported by the National Natural Science Foundation of China(No.20677080,20477055).
文摘Laboratory batch experiments were conducted to study arsenic (As) removal from a naturally contaminated soil using phosphoric acid (H3PO4) and potassium dihydrogen phosphate (KHEPO4). Both H3PO4 and KHEPO4 proved to reduce toxicity of the soil in terms of soil As content, attaining more than 20% As removal at a concentration of 200 mmol/L. At the same time, acidification of soil and dissolution of soil components (Ca, Mg, and Si) resulted from using these two extractants, especially H3PO4. The effectiveness of these two extractants could be attributed to the replacement of As by phosphate ions (PO4^3-). The function of H3PO4 as an acid to dissolve soil components had little effects on As removal. KH2PO4 almost removed as much As as H3PO4, but it did not result in serious damage to soils, indicating that it was a more promising extractant. The results of a kinetic study showed that As removal reached equilibrium after incubation for 360 rain, but dissolution of soil components, especially Mg and Ca, was very rapid. Therefore dissolution of soil components would be inevitable if As was further removed. Elovich model best described the kinetic data of As removal among the four models used in the kinetic study.
基金the National Natural Science Foundation of China (50674016)the National High Technology Research and Develop-ment Program of China (863 Program) ( 2006AA06Z123)
文摘The extraction of Nd^3+ and Sm^3+, including the extraction and stripping capability as well as the separation effect of Nd^3+ or Sm^3+, from a sulfuric acid medium, by mixtures of di-(2-ethylhexyl) phosphoric acid (HDEHP, H2A2(0)) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (HEH/EHP, H2L2(0)) were studied. The distribution ratios and synergistic coefficients of Nd^3+ and Sm^3+ in different acidities were also determined. A synergistic extractive effect was found when HDEHP and HEH/EHP were used as mixed extractants for Sm^3+ or Nd^3+. The chemical compositions of the extracted complex were determined as Nd.(HA2)2-HL2 and Sm.(HA2)2-HL2. The extraction equilibrium constants, enthalpy change, and entropy change of the extraction reaction were also determined.
基金the National Natural Science Foundation of China(51576064,51776070)Beijing Nova Program(Z171100001117064)+2 种基金Beijing Natural Science Foundation(3172030)grants from the Fok Ying Tung Education Foundation(161051)Fundamental Research Funds for the Central Universities(2018QN057,2018ZD08)for financial support。
文摘The catalytic fast pyrolysis of cellulose impregnated with phosphoric acid (H3PO4) offers a promising method for the selective production of levoglucosenone (LGO),a valuable anhydrosugar product.However,the fundamental mechanism for selective LGO formation is unclear.Herein,quantum chemistry calculations and catalytic fast pyrolysis experiments were performed to reveal the formation mechanism of LGO in H3PO4-catalyzed cellulose pyrolysis.H3PO4 significantly decreased the energy barriers of the pyrolytic reactions and altered the competitiveness of the LGO formation pathways,promoting LGO formation.Through different pathways in the non-catalytic and H3P04-catalyzed conditions,LGO is mainly produced from the primary decomposition of glucose units of cellulose and secondary conversion of levoglucosan.The major catalytic formation pathways of LGO comprise similar reactions,with dehydration at the 3-OH+2-H site as the rate-determining step.Importantly,secondary conversion of 1,4;3,6-dianhydro-α-D-glucopyranose is not feasible for LGO formation,in contrast to previous reports.In addition,a high degree of polymerization is beneficial for the selectivity of LGO formation in the catalytic process,because the glycosidic bond is important for the formation of the bicyclic structure (1,5-and1,6-acetal rings).
文摘There are numerous impurities in wet-process phosphoric acid,among which manganese is one of detrimental metallic impurities,and it causes striking negative effects on the industrial phosphoric acid production and downstream commodity.This article investigated the adsorption behavior of manganese from phosphoric acid employing Sinco-430 cationic ion-exchange resin.Resorting FT-IR and XPS characterizations,the adsorption mechanism was proved to be that manganese was combined with sulfonic acid group.Several crucial parameters such as temperature,phosphoric acid content and resin dose were studied to optimize adsorption efficiency.Through optimization,removal percentage and sorption capacity of manganese reached 53.12 wt%,28.34 mg·g^-1,respectively.Pseudo-2nd-order kinetic model simulated kinetics data best and the activation energy was evaluated as 6.34 kJ·mol^-1 for the sorption reaction of manganese.In addition,the global adsorption rate was first controlled by film diffusion process and second determined by pore diffusion process.It was found that the resin could adsorb up to 50.24 mg·g^-1 for manganese.Equilibrium studies showed that Toth adsorption isotherm model fitted best,followed by Temkin and Langmuir adsorption isotherm models.Thermodynamic analysis showed that manganese adsorption was an endothermic process with enhanced randomness and spontaneity.
基金support from the National Key R&D Program of China(2018YFC1900201)the Provincial Key R&D Program of Shanxi(201603D31212003)。
文摘Kiln phosphoric acid(KPA)technology could produce P2O5 with high purity and has been applied in thermal phosphoric acid industry;however the formation of fouling in the high-temperature rotary kiln restricts the stable and long-term operation.In this paper,the reaction of phosphate ores with gaseous P2O5 was investigated in a high-temperature reactor,and the Ca O-SiO2-P2O5 ternary phase diagram was analyzed to understand the fouling formation mechanism.The results showed that the low-melting-point products,such as Ca(PO3)2and Ca2P2O7,are responsible for the fouling in the KPA process.In addition,a small amount of impurities,e.g.,aluminum and iron,could facilitate the generation of the low-melting-point products and cause serious fouling.Based on the high-temperature SiO2-P2O5 and CaO-SiO2-P2O5 phase diagram analysis,the control of Si/Ca molar ratio(e.g.,Si/Ca=2.0)was found to avoid fouling formation in the kiln.These results could provide the operation parameters of reaction temperature and feeds composition to suppress the fouling in the kiln reactor for the phosphoric acid production in industry.
文摘As the world's population exponentially grows,so does the need for the production of food,with cereal production growing annually from an estimated 1.0 billion to 2.5 billion tons within the last few decades.This rapid growth in food production results in an ever increasing amount of agricultural wastes,of which already occupies nearly 50%of the total landfill area.For example,is the billions of dry tons of cellulose-containing spent coffee grounds disposed in landfills annually.This paper seeks to provide a method for isolating cellulose nanocrystals(CNCs)from spent coffee grounds,in order to recycle and utilize the cellulosic waste material which would otherwise have no applications.CNCs have already been shown to have vast applications in the polymer engineering field,mainly utilized for their high strength to weight ratio for reinforcement of polymer-based nanocomposites.A successful method of purifying and hydrolyzing the spent coffee grounds in order to isolate usable CNCs was established.The CNCs were then characterized using current techniques to determine important chemical and physical properties.A few crucial properties determined were aspect ratio of 12±3,crystallinity of 74.2%,surface charge density of(48.4±6.2)mM/kg cellulose,and the ability to successfully reinforce a polymer based nanocomposite.These characteristics compare well to other literature data and common commercial sources of CNCs.
文摘A continuous melt suspension crystallization process has been presented for the purification of the phosphoric acid in this study, which is performed in the cascade of a mixed suspension mixed product removal (MSMPR) crystallizer and a gravity wash column for the subsequent solid-liquid separation. Dynamic behavior in the crystallizer and role of reflux ration on the purification efficiency of column are studied in detail. A reasonable steady state with respect to the liquid phase is achieved after 2 to 3 hrs, which is followed by a solid-phase steady state in terms of the slurry density after 4 hrs. Reflux ratio is the effective parameter for separation and purification by the crystallization equipment from the influences of reflux ratio on the purity of product, the number of theoretical plates and the stability of the operations.
基金Suported by the breeding programs of Sichuan University(SCU2015C002)
文摘In a rotary kiln process for phosphoric acid production,the reaction between gaseous phosphorus pentoxide(P_2O_5)and phosphate ore and silica contained in feed balls(the so-called P_2O_5"absorption")not only reduces phosphorous recovery but also generates a large amount of low melting-point side products.The products may give rise to formation of kiln ring,which interferes with kiln operation performance.In this study,the reactions of gaseous P_2O_5with solid calcium phosphate(Ca_3(PO_4)_2),silica(SiO_2)and their mixture,respectively,were investigated via combined chemical analysis and various characterizations comprised of X-ray diffraction(XRD),Fourier-transform infrared(FT-IR)spectroscopy,thermogravimetric analysis and differential scanning calorimeter(TG&DSC),and scanning electron microscopy and energy dispersive spectrometer(SEM&EDS).Attentions were focused on apparent morphology,phase transformation and thermal stability of the products of the P_2O_5"absorption"at different temperatures.The results show that the temperature significantly affected the"absorption".The reaction between pure Ca_3(PO_4)_2 and P_2O_5 occurred at 500°C.Calcium metaphosphate(Ca(PO_3)_2)was the primary product at the temperatures≤900°C with its melting point≤900°C while calcium pyrophosphate(Ca_2P_2O_7)was obtained over 1000°C,which has a melting point≤1200°C.The"absorption"by pure SiO_2 started at 800°C and the most significant reaction occurred at 1000°C with formation of silicon pyrophosphate(SiP_2O_7)product of melting point≤1000°C.Using mixed Ca_3(PO_4)_2and SiO_2as raw material,the"absorption"by Ca_3(PO_4)_2 was enhanced due to existence of silica.At 600–700°C,silica was inert to P_2O_5and thus formed a porous structure in the raw material,which accelerated diffusion of gaseous P_2O_5inside the mixture.At higher temperatures,the combined"absorption"by calcium phosphate and reaction between silicon dioxide and the"absorption"product calcium pyrophosphate,reinforced the"absorption"by the mixture.Besides,it was found that both Ca(PO_3)_2and SiP_2O_7were unstable at high temperatures and would decompose to Ca_2P_2O_7and SiO_2,respectively,at over 1000°C and 1100°C with the release of gaseous P_2O_5at the same time.
基金Project(06SK2011) supported by the Science and Technology Program of Hunan Province, China
文摘The dry modification of aluminum hydroxide powders with phosphoric acid and the effects of modification of technological conditions on thermal stability, morphology and oil absorption of aluminum hydroxide powders were investigated. The results show that the increase of mass ratio of phosphoric acid to aluminum hydroxide, the decrease of mass concentration of phosphoric acid and prolongation of mixing time are favorable to the improvement of thermal stability of aluminum hydroxide; when the mass ratio of phosphoric acid to aluminum hydroxide is 5:100, the mass concentration of phosphoric acid is 200 g/L and the mixing time is 10 min, the initial temperature of loss of crystal water in aluminum hydroxide rises from about 192.10 to 208.66 ℃, but the dry modification results in the appearance of agglomeration and macro-aggregate in the modified powders, and the oil absorption of modified powders becomes higher than that of original aluminum hydroxide.
基金Project(50371078) supported by the National Natural Science Foundation of China
文摘Corrosion studies of a commercially pure titanium in phosphoric acid solutions at 250 ℃ were carried out by immersion test in an autoclave. At lower phosphoric acid concentration (0.1 mol/L), the corrosion was mild. At higher phosphoric concentration (1.0 mol/L) corrosion, a 25 μm-thick white corrosion products layer was formed on the samples after 24 h immersion. XRD analysis shows that the white layer consists mainly of titanium oxide phosphate hydrate (π-Ti2O(PO4)2·2H2O). The corrosion product shows the morphology of fiber bundles. A thermodynamic analysis of the formation of the corrosion product is presented.
基金Projects(41472278,41202220)supported by the National Natural Science Foundation of ChinaProject(20120022120003)supported by the Research Fund for the Doctoral Program of Higher Education,China+1 种基金Project(2652012065)supported by the Fundamental Research Funds for the Central Universities,ChinaProject supported by Beijing Higher Education Young Elite Teacher Program,China
文摘The rheological behavior of phosphoric acid-water glass grout in different mixing ratios was studied. Grout made of water glass with Baume degree of 20° and 13.4% phosphoric acid by 1:1 volume ratio is found to be more effective in stopping water. Laboratory model test of water shutoff by grouting was conducted. Test results show that the diffusion length and water cutoff effect of the grout are significantly improved as the grout head is raised, due to the dilution of underground water, and it takes the grout longer than its gel time to cut off water.
基金the Natural Science Foundation of Guizhou Province (QianKeHe J[2005]2098)
文摘There exists the most important REE-bearing phosphorite deposit in Southwest of China. Due to the fact that the REE are present in the form of ions in the lattices of collophanite or carbonatfluorapatite, the REE can be enriched in phosphate concentrate by flotation method. The phosphate concentrate is the main raw materials to produce phosphoric acid, therefore, it is significant to further investigate the distribution rule of REE in wet process. In this paper, the single leaching and recycled leaching technology were carried out to investigate the effect of various parameter conditions on distribution of REE in products. The REE compositions of products were analyzed by Inductively Coupled Plasma Emission Mass Spectrometry (ICP-MS) method. It was found that the acidic value of leaching liquor was the main effect factor on the distribution of REE in products. In single leaching stage, P2O5 concentration of leaching liquor slightly varied from 8% to about 10% when the excessive coefficient of sulphuric acid ranged from 1.03 to 1.05, and the distribution proportions of ∑REO in phosphoric acid solution was lower than 40%. However, in recycled leaching process(the condition similar to practical wet process), with an increase of P2O5 concentration as well as the acidic value of leaching liquor, the distribution proportions of ∑REO in phosphoric acid solution could be decreased to 2.56%. That is to say that under the condition similar to practical wet process, more than 90% of REE of phosphate concentrate became precipitation entering into the phosphogypsum product. This investigation will provide valid reference for reasonably recovering or reserving REE in wet-phosphoric acid process.
基金Supported by the Science and Technology Fund of Wuhan City(No:996001016G)
文摘Chiral amino cyclic phosphoric acids, 5-amino-2-hydroxy-4-(4-nitrophenyl)-1,3,2-dioxaphosphorinane 2-oxide and 2-hydroxy-4-(4-methylsulfonylphenyl)-5-phthalimido-1,3,2-dioxaphos phorinane 2-oxide are synthesized in good over yields (64.2%and 72.8%respectively) from 2-amino-1-aryl-1,3-propanediols. The different reaction conditions are necessary in hydrolysis reactions of amino cyclic phosphonyl chlorides.
文摘A hybrid system that consists of a phosphoric acid fuel cell(PAFC),an absorption refrigerator and a refrigeration-space is proposed.The four-heat-source absorption refrigerator,which is driven by the waste heat produced from PAFC,provides cooling for a refrigeration-space.A numerical model is set up to analyze both the steady-state performance and transient performance considering the influences of the electrochemical and thermodynamic irreversibilities.Expressions of the equivalent power output and efficiency of the hybrid system are determined.Moreover,the transient behavior of cold-space temperature is performed and the time to reach a prescribed cold-space temperature is displayed.Thus,the operation regions of the current are optimized at different operating conditions.The results showthat in an appropriate current range,the overall power output and efficiencies of the hybrid system are enhanced.
文摘Cellulose,being as the most abundant nature polymer material and the most promising oil substitute,attracts more and more interests.A new cellulose dissolution system,phosphoric acid(PA)/polyphosphoric acid(PPA) solvent,was investigated in this study.It had been found that a larger cellulose solid content could be dissolved quickly in a hypothermic situation.By evaluating the stability of regenerated cellulose film and the formation of anisotropic solution,the dissolution behavior of cellulose was investigated.Wide-angle X-ray diffraction(WAXD) and Fourier transform infrared spectroscopy(FT-IR) were employed to characterize the crystalline structure and morphology of regenerated cellulose.The measurement results revealed a transition from cellulose-Ⅰ of raw cellulose to cellulose-Ⅱ of regenerated cellulose and a decrease of crystallinity of cellulose after dissolved.This was attributed to the interaction between cellulose and acid solvent,which leaded to the breakage of cellulose intra-and inter-molecule hydrogen bonds and the conformation change of cellulose C6-OH.Moreover,the formation process of cellulose liquid crystal solution was illustrated by polarized light microscope(PLM).That may be induced by the rearranging movement of the cellulose macromolecular chains.
文摘In order to study the effect of fused spinel on the properties of phosphoricacid bonded high alumina castables, samples with different contents of fused spinel were prepared.The results show that when the contents of the fused spinel are between 8% and 16% (mass fraction),the castables have good properties. The castables overcome the shortages of the phosphoric acidbonded high alumina castables with bauxite cement as a hardening promoter. The experimentsdemonstrate that most of the service properties of the castables with fused spinel are better thanthose of the normal phosphoric acid bonded castables which use bauxite cement as a hardeningpromoter. The examination of the materials indicates that free MgO inclusions in the spinel powdercan promote the hardening of the castables.