Hydrothermal Synthesis and Visible-light Photocatalytic Activities of SnS_2 Nanoflakes

SnS2 nanoflakes were successfully synthesized via a simple hydrothermal process. The as-prepared SnS2 samples were characterized by X-ray diffraction（XRD）, scanning electron microscopy（SEM）, nitrogen adsorption-desorption isotherms, and UV-vis diffuse reflectance spectroscopy（DRS）. The photocatalytic activities of the as-prepared SnS2 nanoflakes under visible light irradiation（λ〉420 nm） were evaluated by the degradation of rhodamine B（Rh B）. The effect of hydrothermal temperatures on the photocatalytic efficiency of as-prepared SnS2 nanoflakes was investigated. The experimental result showed that SnS2 nanoflakes synthesized at the temprature of 160 o had higher photocatalytic efficiency and good photocatalytic stability.

Hydrothermal Synthesis and Characterization of Perovskite Oxide AgTaO_3

The perovskite-type AgTaO3 crystals were prepared by mild hydrothermal method and determined by powder X-ray diffraction. Rietveld refinement indicates that AgTaO3 crystallized in an orthorhombic system with the space group Pcmn. The lattice parameters are a=5.5822（1） nm, b=7.8522（2） nm and c=5.5347（1） nm, with α=β=γ= 90.0o. The compound was characterized by scanning electron microscopy（SEM）, X-ray photoelectron spectroscopy （XPS）, high resolution transmission electron microscopy（HR-TEM） and UV-Vis diffuse reflectance spectrometry （UV-Vis DRS）. The photocatalytic activity of AgTaO3 powder was evaluated by the degradation of Congo red under UV-light irradiation. The result shows that the titled compound has a high photocatalytic activity at room temperature and potential application in photocatalysis.

Wettability control of defective TiO_(2)with alkyl acid for highly efficient photocatalytic ammonia synthesis

Ammonia is an important chemical raw material and non-carbon-based fuel.Photocatalytic ammonia production technology as a mild alternative to the traditional Harbor–Bosch route is carried out at the air,liquid,and solid three-phase interface.Promoting the activation of N_(2),depressing hydrogen evolution reaction(HER),and increasing the local N_(2) concentration around the catalyst surface are critical factors in achieving high conversion efficiency.In this paper,we proposed that defective TiO_(2)is surfacemodified by alkyl acids with different carbon chain lengths(C_(2),C_(5),C_(8),C_(11),and C_(14))to tune the catalyst surface properties.The defect sites greatly promote N_(2) adsorption and activation.The wettability of the catalyst can be regulated from hydrophilic to hydrophobic by the length of the alkyl chain.The hydrophobic surface enhances the N_(2) adsorption and increases the local N_(2) concentration due to its aerophile.Meanwhile,it depresses the proton adsorption and HER.Overall,the nitrogen reduction reaction(NRR)is greatly promoted.Among the series of samples,they present a systematic change and have a maximal NRR performance for n-octanoic acid-defective TiO_(2)(C8-Vo-TiO_(2);Vo=oxygen vacancy).The rate of ammonia production can be as high as 392μmol·g^(−1)·h^(−1).This work provides a new strategy for efficient ammonia synthesis at the three-phase interface using photocatalyst technology.

Electrostatic self-assembly of CdS nanowires-nitrogen doped graphene nanocomposites for enhanced visible light photocatalysis

CdS nanowires-nitrogen doped graphene （CdS NWs-NGR） nanocomposites have been fabricated by an electrostatic self-assembly strategy followed by a hydrothermal reduction. The CdS NWs-NGR exhibits higher photoactivity for selective reduction of aromatic nitro organics in water under visible light irradiation than blank CdS nanowires （CdS NWs） and CdS nanowires-reduced graphene oxide （CdS NWs-RGO） nanocomposites. The enhanced photoactivity of CdS NWs-NGR can be attributed to the improved electronic conductivity due to the introduc- tion of nitrogen atoms, which thus enhances the separation and transfer of charge carriers photogenerated from CdS NWs. Our work could provide a facile method to synthesize NGR based one-dimensional （1D） semiconductor composites for selective organic transformations, and broaden the potential applications for NGR as a cocatalyst.

Rapid synthesis of Ti-MCM-41 by microwave-assisted hydrothermal method towards photocatalytic degradation of oxytetracycline

This study employed microwave-assisted hydrothermal method to synthesize Ti-MCM-41,which are mesoporous materials with a high surface area and excellent photocatalytic ability. Fourier transform infrared spectroscopy（FTIR）, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, transmission electron microscopy（TEM）, and ultraviolet–visible spectroscopy（UV–Vis） were employed. The XRD findings showed that Ti-MCM-41 exhibited a peak at 2θ of 2.2°, which was attributed to the hexagonal MCM-41 structure. The BET（Brunauer–Emmett–Teller） results agreed with the TEM findings that Ti-MCM-41 has a pore size of about 3–5 nm and a high surface area of 883 m-2/g. FTIR results illustrated the existence of Si–O–Si and Si–O–Ti bonds in Ti-MCM-41. The appearance of Ti2 p peaks in the XPS results confirmed the FTIR findings that the Ti was successfully doped into the MCM-41 structure. Zeta（ζ）-potential results indicated that the iso-electric point（IEP） of Ti-MCM-41 was at about pH 3.02. In this study, the photocatalytic degradation of oxytetracycline（OTC） at different pH was investigated under Hg lamp irradiation（wavelength 365 nm）. The rate constant（K′obs） for OTC degradation was 0.012 min-1at pH 3. Furthermore, TOC（total organic carbon） and high resolution LC–MS（liquid chromatography–mass spectrometry） analyses were conducted to elucidate the possible intermediate products and degradation pathway for OTC. The TOC removal efficiency of OTC degradation was 87.0%, 74.4% and 50.9% at pH 3, 7 and 10, respectively. LC–MS analysis results showed that the degradation products from OTC resulted from the removal of functional groups from the OTC ring.

TiO_2-loaded activated carbon fiber:Hydrothermal synthesis,adsorption properties and photo catalytic activity under visible light irradiation

TiO2-loaded activated carbon fibers （ACF） were prepared by a hydrothermal method. The samples were characterized by scanning electron microscopy （SEM）, X-ray diffraction （XRD）, Fourier transform infrared （FTIR） spectrometry and UV-vis diffuse reflectance spectra （DRS）. SEM images showed that the TiO2 nanoparticles were deposited on the surface of ACF, and the particle size and loading amount of TiO2 were varied by changing the initial concentration of tetrabutyl titanate （TBOT）. The results of an ash experiment showed that the loading amounts of TiO2 were 18.4%, 43.3%, 52.5%, 75.1%, and 91.1% for initial concentrations of TBOT of 0.07,014, 0.21,0.28, and 0.35 tool/L, respectively, Physical interactions played an important role in the formation of TiO2/ACF composite fibers that absorb UV and visible light. Compared with those of ACF, improved adsorption and photocatalytic activity toward Rhodamine B （RhB） were observed for TiO2/ACF composite fiber. The Rhodamine B could be removed efficiently by TiO2/ACF composite fibers, and the TiO2 loading amount had a significant effect on the photocatalytic activity of TiO2/ACF composite fibers.

具有直接Z型光催化机制的非金属BC4N/aza-CMP异质双层的光催化固氮性能

我们设计了一种不含金属的二维双层异质结构BC_(4)N/aza-CMP,该体系可在水溶液中将N2分子通过光催化作用还原为氨.通过密度泛函理论和非绝热分子动力学方法,我们发现该异质结构中的光生载流子遵循直接Z型迁移机制.这将有效分离光生电荷并使氮还原反应和氧发生反应分别在BC_(4)N层和aza-CMP层上进行,实现反应位点的空间分离.值得一提的是,BC_(4)N上的B原子可以有效吸附N2分子并激活N≡N键,这将降低氮还原反应的过电势并促进随后的质子化进程,且该异质双层具有适宜的带隙和带边位置,能够有效吸收太阳光并提供充足的驱动力来触发氧化还原反应,实现无任何牺牲剂辅助的光催化氨合成.本工作将为直接Z型固氮光催化剂的设计提供重要借鉴,并促进太阳能驱动的氨合成的发展.

Sodium-doped carbon nitride nanotubes for efficient visible light-driven hydrogen production

Sodium-doped carbon nitride nanotubes （Nax-CNNTs） were prepared by a green and simple two-step method and applied in photocatalytic water splitting for the first time. Transmission electron microscopy （TEM） element mapping and X-ray photoelectron spectroscopy （XPS） measurements confirm that sodium was successfully introduced in the carbon nitride nanotubes （CNNTs）, and the intrinsic structure of graphitic carbon nitride （g-C3N4） was also maintained in the products. Moreover, the porous structure of the CNNTs leads to relatively large specific surface areas. Photocatalytic tests indicate that the porous tubular structure and Na＋ doping can synergistically enhance the hydrogen evolution rate under visible light （λ 〉 420 nm） irradiation in the presence of sacrificial agents, leading to a hydrogen evolution rate as high as 143 μmol·h-1 （20 mg catalyst）. Moreover, other alkali metal-doped CNNTs, such as Lix-CNNTs and Kx-CNNTs, were tested; both materials were found to enhance the hydrogen evolution rate, but to a lower extent compared with the Nax-CNNTs. This highlights the general applicability of the present method to prepare alkali metal-doped CNNTs; a preliminary mechanism for the photocatalytic hydrogen evolution reaction in the Nax-CNNTs is also proposed.