Dynamically Photocrosslinking of Polypropylene/EPDM Blends as a Thermoplastic Elastomer

The mechanical properties and the crystal morphological structures of the dynamically photocrosslinked polypropylene(PP)/ethylene-propylene-diene terpolymer(EPDM) blends have been studied by means of mechanical tests, wide-angle X-ray diffraction(WAXD), and differential scanning calorimetry(DSC). The dynamically photocrosslinking of the PP/EPDM blends can improve the mechanical properties considerably, especially the notched Izod impact strength at low temperatures. The data obtained from the mechanical tests show that the notched Izod impact strength of the dynamically photocrosslinked sample with 30% EPDM at -20 ℃ is about six times that of the uncrosslinked sample with the same EPDM component. The results from the gel content, the results of WAXD, and the DSC measurements reveal the enhanced mechanism of the impact strength for the dynamically photocrosslinked PP/EPDM blends as follows: (1) There exists the crosslinking of the EPDM phase in the photocrosslinked PP/EPDM blends; (2) The β-type crystal structure of PP is formed and the content of α-type crystal decreases with increasing the EPDM component; (3) The graft copolymer of PP-g-EPDM is formed at the interface between the PP and EPDM components. All the above changes of the crystal morphological structures are favorable for increasing the compatibility and enhancing the toughness of the PP/EPDM blends at low temperatures.

A STUDY ON THE DEGRADATION MECHANISM OF PHOTOCROSSLINKING PRODUCTS FORMED BY CYCLIZED POLYISOPRENE-DIAZIDE SYSTEM UNDER THE INFLUENCE OF ALKYL BENZENE SULFONIC ACIDS

The degradation mechanism of photocrosslinking products formed by cyclized polyisoprene-diazide system under the influence of the different alkyl benzene sulfonic acids was studied. The effects of alkyl chain length and the concentration of alkyl benzene sulfonic acids on the rate of degradation reaction were discussed. It was found that in the initial stage of degradation, the cyclicity ratio and the average fused ring number did not change considerably, but the percentage of uncyclized parts content varied significantly. The suitable mechanism was supposed.

Systematic study on fabrication of hollow poly(vinyl cinnamate)particles by particulate interfacial photocrosslinking

Hollow polymer particles are widely used in various industries as coatings and thermal insulation materials.The encapsulation capabilities of various functional molecules and/or nanomaterials also provide access to applications such as drug delivery,heat storage,and catalysis,as well as self-healing materials.In this study,we successfully fabricated hollow polymer particles from poly(vinyl cinnamate)(PVC)particles using LED light(λ=265 nm)through interfacial photocrosslinking.Furthermore,we systematically studied the effect of various parameters(solid contents of parent particles,photoirradiation time,photoirradiation power,and polymer chain length)on the polymer shell thickness of the hollow PVC particles fabricated by interfacial photocrosslinking.These findings are expected to further promote the use of hollow polymer particles in pharmaceutical and material applications.

The Photochemical Study of HSA and BSA with Resonance Light Scattering and Fluorescence Spectra

The resonance light-scattering (RLS) of human serum albumin (HSA) and bovine serum albumin (BSA) is reported for the first time, and applied to study photochemical reaction of HSA and BSA. The fact of photocrosslinking self-association effect in HSA and BSA solutions is identified by the enhancement of RLS. The fluorescence quenching at about 350 nm and 700 nm proves that tryptophan (Trp) residues are one of the photochemical activity sites in HSA and BSA molecules. The Rayleigh scattering (RS) spectra of HSA and BSA that were neglected in fluorescence spectra before are found at about 296 nm, 592 nm and 888 nm for the first time, and are of adventageous to studying the aggregation of HSA or BSA. The possible photochemical reaction mechanism is also proposed.

RECENT DEVELOPMENTS IN PHOTOINITIATED CROSSLINKING OF POLYETHYLENE AND ITS INDUSTRIAL APPLICATIONS

The recent developments in the photoinitiated cross-linking of polyethylene and the significant breakthrough of its industrial application are reviewed. The enhanced photo-initiation system, the dynamics of photoinitiated crosslinking, the optimum conditions, the crystal morphological structures and related properties, and the photo- and thermo-oxidation stability of photocrosslinked polyethylene (XLPE) materials have been elucidated systematically. A new technique for producing photocrosslinked XLPE-insulated wire and cable is described in detail. It can be expected that the future applications of photocrosslinking technique of polyolefins will be very promising.

PREPARATION AND PHOTOSENSITIVITY OF WATER SOLUBLE PHENOLIC RESINS CONTAINING ACRYLOYL AND QUATERNARY AMMONIUM CHLORIDE GROUPS

New water soluble and photocrosslinkable prepolymers containing acrylate and quaternary ammonium salt groups were synthesized from epoxy phenolic resin via ring-opening reaction with acrylic acid and with aqueous solution of triethylamine hydrochloride successively. The second reaction needs no phase transfer catalyst to accelerate, since the product formed can act as a phase transfer catalyst. The prepolymer obtained contains both photocrosslinkable acrylate groups and hydrophilic quaternary ammonium salt groups. Optimum conditions for these reactions were studied. The photosensitivity of the prepolymer was also investigated. The effects of different photoinitiators, different crosslinkable diluent monomers and amine accelerator on the photosensitivity of the prepolymer were compared. The photoinitiator of hydrogen abstraction type is still effective without using amine or alcohol as accelerator, because the prepolymer contains a H beside the OH groups formed in the ring-opening reactions.

PHOTOINITIATED CROSSLINKING OF EPDM/INORGANIC FILLER BLENDS AND CHARACTERIZATION OF RELATED PROPERTIES

Photoinitiated crosslinking of ethylene-propylene-diene terpolymer （EPDM） blends filled with calcium carbonate, talc and calcined kaolin （CK） in the presence of benzil dimethyl ketal as photoinitiator and trimethylolpropane triacrylate as crosslinker and their related properties have been studied by different analytical methods, The results from gel content and heat extension determination show that the efficiency ofphotocrosslinking of EPDM increases with increasing the content of diene and its molecular weight. The EPDM blends with 100 phr different inorganic fillers can be photocrosslinked to gel content of above 60% by 5 s UV-irradiation under optimum conditions. Under the same conditions of irradiation, the orders of photocrosslinking rate and final gel content are EPDM/CaCO3 〉 EPDM/talc 〉 EPDM/CK. The data from thermogravimetric analysis, dynamic mechanical thermal analysis, electrical properties, mechanical tests and scanning electron microscopy show that UV irradiation crosslinking apparently enhances the thermal stability, mechanical properties and electrical properties of the photocrosslinked EPDM/inorganic filler samples. Although the attenuated total-reflection FTIR data show that inorganic fillers can promote the surface photo-oxidation of EPDM/inorganic filler samples with increasing the irradiation time, the above related properties of the photocrosslinked EPDM blends irradiated within 5 s are enough to satisfy many applications in the cable industry.

REACTION MECHANISM OF BENZOPHENONE-PHOTOINITIATED CROSSLINKING OF POLYETHYLENE

The radical intermediates, the crosslink microstructures, and the reaction mechanism of benzophenone (BP)-photoinitiated crosslinking of low-density polyethylene (LDPE) and model compounds (MD) have been reviewed in detail. The spin-trapping electron spin resonance (ESR) spectra obtained from the LDPE/BP systems with spin-trap agents show that two kinds of polymer radical intermediates are mainly formed: tertiary carbon and secondary carbon radicals. The spin-trapping ESR studies of MD/BP systems give further evidence that photocrosslinking reactions of PE predominantly take place a sites of tertiary carbon, secondary carbon, and especially allylic carbon when available. The high resolution C-13-NMR spectra obtained from LDPE and MD systems show that the crosslink microstructures have H- and Y-type links and that their concentrations are of the same order. The fluorescence, ESR, C-13 and H-1-NMR spectra from the PE and MD systems demonstrate that the main photoreduction product of BP (PPB) is benzpinacol formed by the recombination of two diphenylhydroxymethyl (K-.) radical intermediates. Two new PPB products: an isomer of benzpinacol with quinoid structure, 1-phenylhydroxymethylene-4-diphenylhydroxymethyl-2,5-cyclobexadiene and three kinds of alpha-alkyl-benzhydrols have been detected and identified. These results provide new experimental evidence for elucidating the reaction mechanism in the BP-photoinitiated crosslinking of polyethylene.

3D human nonalcoholic hepatic steatosis and fibrosis models

This study presents a simple and robust three-dimensional human hepatic tissue model to emulate steatotic and fibrotic conditions and provide an in vitro model for drug testing and mechanistic studies.Using a photolithographic biofabrication method with a photomask featuring hexagonal units,liver cells,including a human hepatic cell line(HepG2-C3A)and a human hepatic stellate cell line(LX-2)were embedded in gelatin methacryloyl hydrogel.Hepatic steatosis was induced by supraphysiological concentration of free fatty acids;hepatic fibrosis was induced by transforming growth factor-β1.Induction of steatosis was confirmed by Oil Red O and BODIPY staining and was inhibited with toyocamycin and obeticholic acid.Induction of fibrosis was confirmed by immunostaining for collagen type I and alpha smooth muscle actin and inhibited by rapamycin and curcumin treatment.This model was further preliminarily validated using primary human hepatocytes in a similar setup.These constructs provide a viable,biologically relevant,and higher throughput model of hepatic steatosis and fibrosis and may facilitate the study of the mechanisms of disease and testing of liver-directed drugs.

KINETICS AND MECHANISM OF PHOTOINDUCED POLYMERIZATION BY α,α-DIMETHOXY-α-PHENYL ACETOPHENONE

α,α-dimethoxy-α-Phenyl acetophenone (DMPA) is an efficient and thermally stable photoinitiator. Here its spectral characteristics in the transient state were shown. The transient species were identified as a benzoyl radical and a dimethoxyi benzyl radical that played a primary initiation role in polymerization. The kinetics and mechanism of the bulk polymerization of MMA were investigated. The exponent of DMPA concentration and k_p/k_1^(1/2) value were found to be 0.5 and 0.066 mol(-1/2)l^(1/2)s^(-1/2), respectively. The existence of oxygen led to obtain the polymer with higher molecular weight, which can be attributed to the occurrence of the subsequent polymerization induced by active polymer end group. In the photocrosslinking reaction, the dependence of DMPA content on initial rate has been found. A principal reason is that the sample contained higher percentage of DMPA has higher light-absorbed efficiency. In solid film, higher concentration of DMPA is permitted to be used because there is little excited state self-quenching effect in the rigid medium.

Biomimetic microchannel network with functional endothelium formed by sacrificial electrospun fibers inside 3D gelatin methacryloyl(GelMA)hydrogel models

Three-dimensional(3D)hydrogel models play a crucial role in tissue engineering for promoting tissue regeneration.A biomimetic microchannel network system in the 3D hydrogel model is necessary for optimal cellular function.This report describes the preparation of a biomimetic hydrogel scaffold with an internal microchannel network,using electrospinning techniques and the sacrificial template method for 3D cell culture.Microchannels and cavities were created within the gelatin methacryloyl(GelMA)hydrogel by sacrificing polyvinyl alcohol(PVA)electrospun fibers(>10µm),resulting in the creation of microvessel-like channels.Mechanical characterizations,swelling properties,and biodegradation analysis were conducted to investigate the feasibility of a biomimetic microchannel network hydrogel scaffold for 3D cell culture applications.Compared to pure GelMA hydrogel,the hydrogel with microchannels promoted cell proliferation,adhesion,and endothelial tube formation.Moreover,the results confirmed that the biomimetic microchannel network scaffold had a major impact on the distribution and arrangement of human umbilical vein endothelial cells(HUVECs)and can enable the formation of artificial microvasculature by the culture of HUVECs and cell media perfusion.

MMP-2 and upconverted UV dual-mediated drug sequential delivery and on-site immobilization for enhanced multidrugresistant cancer therapy

Controlled drug delivery holds great potential for effective tumor treatment owing to the merits of overcoming drug resistance and improving therapeutic efficacy while minimizing systemic toxicity.However,accurate and controllable delivery of chemotherapeutics into tumor tissue with high efficiency remains a huge challenge.Taking advantage of the UV-emitting characteristics of upconversion nanoparticles(UCNPs),herein we for the first time report an MMP-2 enzyme and near infrared(NIR)dual-mediated sequential drug delivery and in-situ immobilization(ENDDI)system that is fabricated by decorating UCNPs with MMP-2 responsive and photocrosslinkable peptide bearing anticancer drug doxorubicin(DOX)for overcoming multidrug resistance.Upon cleavage with tumor-specific MMP-2,the peptide fragment containing a photolabile benzophenone(BP)and DOX could be released and in-situ immobilized within the tumor through the covalent crosslinking reaction between BP and neighboring biomolecules under the excitation of converted UVemission from UCNPs,which remarkably blocks the exocytosis of DOX leading to prolonged drug retention,achieving significant suppression of DOX-resistant breast tumors.Our current dual stimuli-mediated sequential drug delivery and in-situ immobilization represent a generalizable strategy for the effective treatment of multidrug resistant tumors.

Quick photofabrication of functional nanospheres from de novo designed peptides for NIR fluorescence and MR imaging

Combining the noncovalent and covalent interactions,a series of peptide amphiphiles were designed de novo and synthesized to architect functional assemblies by means of photochemistry.The strand of peptide sequence was structurally capped with photoactive tyrosine-tyrosine(YY)motifs at both termini,and the spacing was filled by alternating of hydrophilic D(L-aspartate)and hydrophobic X(ε-aminocaproic acid)structure.Upon visible-light irradiation,these de novo designed peptides underwent rapid photocrosslinking within merely 10 min.Interestingly,the modulation of alternating D-X pairs in occupying spacer would adjust molecular amphiphilicity,regulate charge distribution,and control particle size and loading capacity of peptide nanospheres(PNS)in aqueous media.With entirely peptide-based matrix,this PNS system could host cationic indicators of fluorescent rhodamine and magnetic GdIII for exemplar near infrared(NIR)fluorescence and magnetic resonance(MR)imaging,which paves a pathway to biomaterial and biomedical applications using de novo designed peptides.

Photocrosslinkable Col/PCL/Mg composite membrane providing spatiotemporal maintenance and positive osteogenetic effects during guided bone regeneration

Guided bone regeneration membranes have been effectively applied in oral implantology to repair bone defects.However,typical resorbable membranes composed of collagen(Col)have insufficient mechanical properties and high degradation rate,while non-resorbable membranes need secondary surgery.Herein,we designed a photocrosslinkable collagen/polycaprolactone methacryloyl/magnesium(Col/PCLMA/Mg)composite membrane that provided spatiotemporal support effect after photocrosslinking.Magnesium particles were added to the PCLMA solution and Col/PCLMA and Col/PCLMA/Mg membranes were developed;Col membranes and PCL membranes were used as controls.After photocrosslinking,an interpenetrating polymer network was observed by scanning electron microscopy(SEM)in Col/PCL and Col/PCL/Mg membranes.The elastic modulus,swelling behavior,cytotoxicity,cell attachment,and cell proliferation of the membranes were evaluated.Degradation behavior in vivo and in vitro was monitored according to mass change and by SEM.The membranes were implanted into calvarial bone defects of rats for 8 weeks.The Col/PCL and Col/PCL/Mg membranes displayed much higher elastic modulus(p<0.05),and a lower swelling rate(p<0.05),than Col membranes,and there were no differences in cell biocompatibility among groups(p>0.05).The Col/PCL and Col/PCL/Mg membranes had lower degradation rates than the Col membranes,both in vivo and in vitro(p<0.05).The Col/PCL/Mg groups showed enhanced osteogenic capability compared with the Col groups at week 8(p<0.05).The Col/PCL/Mg composite membrane represents a new strategy to display space maintenance and enhance osteogenic potential,which meets clinical needs.

Photocrosslinkable Polynorbornene-based Block Copolymers with Enhanced Dielectric and Thermal Properties

Block copolymers poly（endo-N-3,5-bis（trifluoromethyl）biphenyl-norbornene-pyrrolidine）-block-poly（exo-N-（cinnamoyloxyethyl）-7-oxanorborn-5-ene-2,3-dicarboximide）（endo-PTNP-b-exo-PCONBI） and poly（exo-N-3,5-bis（trifluoromethyl）biphenyl-norbornene-pyrrolidine）-block-poly（exo-N-（cinnamoyloxyethyl）-7-oxanorborn-5-ene-2,3-dicarboximide）（exo-PTNP-b-exo-PCONBI） were synthesized by ring-opening metathesis polymerization. The endo- or exoPTNP served as the high dielectric functional chain, and exo-PCONBI acted as the crosslinking segment. The endo-PTNPb-exo-PCONBI, in which endo-PTNP has a high content of trans double bond and adopts isotactic configuration, shows a dielectric constant（？） of 15.5, whereas exo-PTNP-b-exo-PCONBI, in which exo-PTNP has 67% trans double bonds and atactic microstructure, displays relatively low ？ of 7.1. The cinnamate groups in exo-PCONBI were crosslinked to form three-dimensional network by cycloaddition reaction under UV irradiation. Exposed to UV-light for 10 min, the cinnamate group in polymer films has a crosslinking conversion of 36%, as determined by UV-Vis absorption measurements. By photocrosslinking, the polymer film has an increased ？ of 16.6, a dielectric loss of 0.03, an elevated glass-transition temperature of 137 ？C, and an enhanced decomposition temperature of 405 ？C, compared to those of polymer films without irradiation.

POLYETHYLENE CROSSLINKED WITH ULTRAVIOLET LIGHT

It was first proposed by Oster in 1956 that polyethylene could be crosslinked with ultraviolet fight in the presence of some photosensitizers. But the photocrossfinking method was not used in industry for a long period because the penetration of the light is limited. The recent work done by Rnby et al. is outstanding in the improvement on this method, and it is competitive to the high-energy irradiation method and the thermalchemistry method. Therefore, the photocrosslinking has a promising prospect in application now. This note is a brief introduction to the results about the theoretical analysis and

In situ sol-gel synthesis of hyaluronan derivatives bio-nanocomposite hydrogels

The main driving idea of the present study was the comparison between two different chemical modifications of hyaluronic acid(HA)followed by the development of nanocomposite hydrogels directly in situ by biomineralization of photocrosslinkable HA polymers through sol-gel synthesis.In this way,it has been possible to overcome some limitations due to classical approaches based on the physical blending of inorganic fillers into polymer matrix.To this aim,methacrylated and maleated HA,synthesized with similar degree of substitution(DS)were compared in terms of mechanical and physico-chemical properties.The success of in situ biomineralization was highlighted by reflect Fourier transform infrared spectroscopy and thermogravimetric analysis.Furthermore,mechanical characterization demonstrated the reinforcing effect of inorganic fillers evidencing a strong correlation with DS.The swelling behavior resulted to be correlated with filler concentration.Finally,the cytotoxicity tests revealed the absence of toxic components and an increase of cell proliferation over culture time was observed,highlighting these bio-nanocomposite hyaluronan derivatives as biocompatible hydrogel with tunable properties.

Bioprinting and regeneration of auricular cartilage using a bioactive bioink based on microporous photocrosslinkable acellular cartilage matrix

Tissue engineering provides a promising strategy for auricular reconstruction.Although the first international clinical breakthrough of tissue-engineered auricular reconstruction has been realized based on polymer scaffolds,this approach has not been recognized as a clinically available treatment because of its unsatisfactory clinical efficacy.This is mainly since reconstruction constructs easily cause inflammation and deformation.In this study,we present a novel strategy for the development of biological auricle equivalents with precise shapes,low immunogenicity,and excellent mechanics using auricular chondrocytes and a bioactive bioink based on biomimetic microporous methacrylate-modified acellular cartilage matrix(ACMMA)with the assistance of gelatin methacrylate(GelMA),poly(ethylene oxide)(PEO),and polycaprolactone(PCL)by integrating multi-nozzle bioprinting technology.Photocrosslinkable ACMMA is used to emulate the intricacy of the cartilage-specific microenvironment for active cellular behavior,while GelMA,PEO,and PCL are used to balance printability and physical properties for precise structural stability,form the microporous structure for unhindered nutrient exchange,and provide mechanical support for higher shape fidelity,respectively.Finally,mature auricular cartilage-like tissues with high morphological fidelity,excellent elasticity,abundant cartilage lacunae,and cartilage-specific ECM deposition are successfully regenerated in vivo,which provides new opportunities and novel strategies for the fabrication and regeneration of patient-specific auricular cartilage.