Preparation of Manganese Oxide and Its Adsorption Properties

The in-situ oxidation of manganese sulfate solution with H2O_(2),sodium hypochlorite,potassium permanganate and oxygen as oxidants was investigated by means of SEM,EDS,XRD,BET and infrared analysis,and the effects of different oxidants on the morphology,phase composition,surface properties and specific surface area of manganese oxides were investigated.The experimental results show that the diameter of manganese oxide particles prepared with H_(2)O_(2)is the smallest,about 50 nm,and the specific surface area is the largest,63.8764 m^(2)/g.It has the advantages of abundant surface hydroxyl groups,no introduction of other impurities and large adsorption potential.It is most suitable to be used as an oxidant for oxidizing manganese sulfate solution to prepare manganese oxide by in-situ oxidation.Nano manganese oxide prepard by H_(2)O_(2)in-situ oxidation method is used as adsorbent to adsorb cobalt and nickel impurities in manganese sulfate.When the reaction pH is 6,the reaction time is 30min and the amount of adsorbent is 1.0 g,the adsorption rates of cobalt and nickel impurities in 100ml manganese sulfate solution are 97.59%and 97.67%,respectively.The residual amounts of cobalt and nickel meet the industrial process standard of first-class products(Co,Ni w/%≤0.005)of high-purity manganese sulfate(Hg/t4823-2015)for batteries.The study plays a guiding role in the preparation and regulation of manganese oxide,and provides a new method with high efficiency,purity and adsorbent availability for the preparation of high-purity manganese sulfate solution.

Influence of Plastic and Coconut Shell (Cocos nucifera L.) on the Physico-Mechanical Properties of the 8/6 Composite Rafter

In this paper, the authors aim to propose the use of waste plastics as a binder in a coconut shell reinforcement for the development of an 8/6 size composite rafter to replace the natural 8/6 size backbone in construction. Following a study into the choice of the best proportions, a total of 30 size 8/6 composite rafters with different proportions of 20%, 25%, 30%, 35%, 40% and 50% plastic content were developed. All the 8/6 composite rafters were subjected to mechanical (3-point bending strength and Monnin hardness) and physical (bulk density and water absorption) characterization analyses. The results show that flexural strength increases from 27.56 MPa to 33.30 MPa for proportions ranging from 20% to 35% plastic content. Above 35% plastic, the strength drops to 19.60 MPa for a 50% plastic content. Similarly, the Monnin hardness drops from 9 mm to 5 mm when the plastic content varies from 20 to 50%. As for the results of the physical characterisation, the values obtained for apparent density vary from 0.89 to 1 for proportions varying from 20% to 35% plastic content and drop to 0.94 for 50% plastic content. As for water absorption, values drop from 6.82% to 2.45% when the plastic content increases from 20% to 50%. These mechanical strengths stabilise at 35% plastic content. The development of an 8/6 chevron composite material based on plastic and coconut shell could therefore be a way of recovering waste and solving the problem of deforestation.

Effect of molasses binder on the physical and mechanical properties

Molasses was used as an alternative binder to the bentonite binder. The change in moisture absorption by pellets prepared with different iron ores and different molasses contents were investigated. Iron ore properties exerted the major effect on pellet behavior and final pellet quality. The absorbed moisture content of pellets prepared without binder, bentonite-added pellets, and molasses-added pellets were in the range of 7.72%–9.95%, 9.62%–10.84%, and 6.14%-6.69%, respectively. The wet pellet compressive strength of molasses-added pellets(43–230 N/pellet) was superior to that of bentonite-added pellets(9.47–11.92 N/pellet). The compressive strength of dried molasses-modified pellets increased to 222–394 N/pellet, which is currently the highest value achieved for dried pellets.

Review of the influence of freeze-thaw cycles on the physical and mechanical properties of soil

Seasonally frozen soil is a four-phase material and its physical-mechanical properties are more complex compared to the unfrozen soil. Its physical properties changes during the freeze-thaw process; repeated fieeze-thaw cycles change the characteristics of soil, which can render the soil from an unstable state to a new dynamic equilibrium state. The freezing process changes the structttre coupled between the soil particle arrangements, which will change the mechanical properties of the soil. The method of significance and interaction between different fac tors should be considered to measure the influence on the propties of soil under freeze-thaw cycles.

Effects of Polypropylene Fibers on the Physical and Mechanical Properties of Recycled Aggregate Concrete

The viability of using polypropylene fibers(PPF) in concrete was largely studied. Yet, few of the existing research studies investigated the effects of PPF on the properties of concrete containing recycled concrete aggregate(RCA). Mixes with different RCA replacement ratios and different PPF content were designed and tested. The test results showed that the addition of PPF did not change significantly the compressive strength and the density of the concrete, but slightly decreased its modulus of elasticity and Poisson’s ratio. The drop in the splitting tensile strength and the flexural strength due to RCA inclusions was to a large extent compensated by the PPF addition. The water absorption decreased and the percent voids increased with increased PPF addition. Correlations between the RCA content, the PPF content and the properties of concrete were studied. Useful regression models were proposed to predict the properties of concrete in relevant ranges of RCA and PPF content.

Effects of sintering atmosphere on the physical and mechanical properties of modified BOF slag glass

This study proposes an efficient way to utilize all the chemical components of the basic oxygen fttrnace （BOF） slag to prepare high value-added glass-ceramics. A molten modified BOF slag was converted from the melting BOF slag by reducing it and separating out iron component in it, and the modified BOF slag was then quenched in water to form glasses with different basicities. The glasses were subsequently sintered in the temperature range of 600-1000℃ in air or nitrogen atmosphere for 1 h. The effects of different atmospheres on the physical and mechanical properties of sintered samples were studied by using differential scanning calorimetry （DSC）, X-ray diffraction （XRD） and scanning electron microscopy （SEM） and by conducting experiment on evaluating the sintering shrinkage, water absorption and bulk density. It is found that the kinetics of the sintering process is significantly affected by sintering atmosphere. In particular, compared with sintering in air atmosphere, sintering in N2 atmosphere promotes the synergistic growth of pyroxene and melilite crystalline phases, which can contribute to better mechanical properties and denser microstructure.

Predicting uniaxial compressive strength of serpentinites through physical,dynamic and mechanical properties using neural networks

The uniaxial compressive strength(UCS)of intact rock is one of the most important parameters required and determined for rock mechanics studies in engineering projects.The limitations and difficulty of conducting tests on rocks,specifically on thinly bedded,highly fractured,highly porous and weak rocks,as well as the fact that these tests are destructive,expensive and time-consuming,lead to development of soft computing-based techniques.Application of artificial neural networks(ANNs)for predicting UCS has become an attractive alternative for geotechnical engineering scientists.In this study,an ANN was designed with the aim of indirectly predicting UCS through the serpentinization percentage,and physical,dynamic and mechanical characteristics of serpentinites.For this purpose,data obtained in earlier experimental work from central Greece were used.The ANN-based results were compared with the experimental ones and those obtained from previous analysis.The proposed ANN-based formula was found to be very efficient in predicting UCS values and the samples could be classified with simple physical,dynamic and mechanical tests,thus the expensive,difficult,time-consuming and destructive mechanical tests could be avoided.

Investigation of Different Washing Effects on Physical and Mechanical Properties of Cotton Knitted Garments

This paper deals with three types of washing (enzyme, softener, Silicone) effects on 100% cotton Single Jersey T-shirt, Slub Single Jersey T-shirt, Double Lacoste (5% Lycra) Polo shirt, Single jersey CVC (T-shirt) and PC single Jersey (T-shirt). Typical industrial washing procedures and techniques were followed and then physico-mechanical properties were analyzed under standard condition. It is observed that after washing, weight of each garments has increased from 5% to 36%;stitch length of the constituted fabric has decreased from 1% to 10% approximately;CPI has increased 23% for CVC fabric only for enzyme treatment and for other process it has a little bit or no wash effects. Same effects found for WPI except 100% cotton and Double Lacoste. Shrinkage property both for lengthwise and widthwise remains the same except CVC and Double Lacoste knitted garments and spirality has almost unchanged except 100% cotton and slub fabric. Both the dry and wet rubbing properties have improved after any types of wash except 100% cotton on Silicone wash. Water absorbency property has increased;pH of all the samples is under controlled and lies between 4.5 and 5.0. But there is no significant change of colorfastness to wash and stain after these washing treatments.

Effect of carbon nanotube on physical and mechanical properties of natural fiber/glass fiber/cement composites

The objective of this investigation was to introduce a cement-based composite of higher quality. For this purpose new hybrid nanocomposite from bagasse fiber,glass fiber and multi-wall carbon nanotubes（MWCNTs）were manufactured. The physical and mechanical properties of the manufactured composites were measured according to standard methods. The properties of the manufactured hybrid nanocomposites were dramatically better than traditional composites. Also all the reinforced composites with carbon nanotube, glass fiber or bagasse fiber exhibited better properties rather than neat cement.The results indicated that bagasse fiber proved suitable for substitution of glass fiber as a reinforcing agent in the cement composites. The hybrid nanocomposite containing10 % glass fiber, 10 % bagasse fiber and 1.5 % MWCNTs was selected as the best compound.

BEHAVIOR OF OXYGEN IN DG^(TM) INVAR-Cu ALLOYS AND ITS EFFECTS ON MECHANICAL AND PHYSICAL PROPERTIES

ＴｈｅＤＧＴＭｉｎｖａｒＣｕｌｏｗｅｘｐａｎｓｉｏｎａｎｄｈｉｇｈｃｏｎｄｕｃｔｉｖｉｔｙａｌｏｙｓｗｅｒｅｆｉｒｓｔｄｅｖｅｌｏｐｅｄｂｙｔｈｅＤｅｐａｒｔｍｅｎｔｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｅｒｉｎｇｏｆｔｈｅＣｅ...

Physical and mechanical properties of Klainedoxa gabonensis with engineering potential

Adequate information is sparse for many tropical timbers on their engineering applications, which make their international promotion difficult. The physical and mechanical properties of Klainedoxa gabonensis Pierre ex Engl. （a lesserutilized species） and Entandrophragma cylindricum were compared. K. gabonensis contained more moisture with greater density at 12 % moisture content than E. cylindricum and had a tangential-radial ratio for swelling and shrinkage of 1.31-1.38 and 1.58-1.63, respectively, within acceptable thresholds for engineering/structural timbers. For K. gabonensis, shear parallel to grain was 32.2 ± 0.4-33.5 ±1 N mm^-2; compressive parallel to grain, 80.7 ± 1.4-90.6± 1 N mm^-2; modulus of rupture, 204± 4.0-214 ± 4.0 N mm^-2 and modulus of elasticity, 28,932 ± 664-29,493 ±822 N mm^-2. These properties were superior to those of E. cylindricum [（15.5 ± 0.9）- （15.6 ± 0.6）, （56.4 ± 4.5）-（63.6 ± 1.2）, （99.4 ± 4.7）- （121.3 ± 10.6）, and （9987.4 ± 207）-（10,051 ± 258） N mm^-2, respectively] and compared well with those of several traditional timbers for conslruction and furniture production. Its use would contribute to minimize pressure on the primary timbers in the forests and widen the raw material base for wooden products.

SYSTEMATIC STUDY OF PHYSICAL AND MECHANICAL PROPERTIES OF IMPORTANT CHINESE WOODS

In this paper,the physical and mechanical properties of important Chinese woodswere studied by using the methods of variable analysis, regression analysis,correlation analysis,principle component analysis and so on systematically.The results showed synthetical characteristicof the physical and mechanical properties of Chinese woods.Some opinions of former authors wererevised and some new laws were discovered.That is helpful to study of the physical and mechanicalproperties of woods.

Selected physical and chemical properties of mechanically extracted neem seed oil sourced as a preservative for ligno-cellulose in south-western Nigeria

Most of the seeds produced by neem （Azadirachta indica A. Juss） trees in Nigeria are currently underutilized. Hence, relevant literature provides only limited information conceming many of the seed oils from this country, especially where it concems the potential applications of these oils as preservatives for ligno-cellulose against bio-deterioration. Using standard procedures therefore, this study was carried out to evaluate and document selected physical and chemical properties of neem seed oil （NSO）, mechanically extracted using a cold press at 31.03 N-mm^-2 pressure and a room temperature of 25 ± 2℃. The results show that oil yield was 38.42% with a specific gravity of 0.91 ± 0.01. The amount of acid was 18.24 ± 1.31 mg KOH.g^-1 and that of iodine 93.12 ± 2.01 g-100 g^- 1, while saponification and peroxide values were 172.88 ± 2.06 and 1.42 ± 0.04 mg·g^-1 respectively. The implication of the values obtained, particularly those for the chemical properties, as they concern the potential application of NSO as a preservative for ligno-eellulose, is likely that it may be useful in this regard since the values may support some of the documented anti-microbial properties of the oil, although other physical and chemical properties that may affect this potential are recommended for investigations. Conclusions and other recommendations follow in line with the results of the study.

Effect of Waste Marble Powder on Physical and Mechanical Properties of Concrete

The emission of greenhouse gases from cement production is an obstacle for sustainable development of construction industry.The use of waste materials in constructions instead of cement could be a feasible solution to green construction.Waste marble powder with good cementing property can be used in concrete partially replace cement.In this research,the effects of using waste marble powder on the physical and mechanical properties of concrete have been studied.Three groups of particle size and five levels of replacement ratio(5%,10%,15%,20%,25%)for each group have been designed.During the different stage of hydration process,the microstructure,phase composition and thermal properties of marble-cement paste have been investigated,the influence of particle size of marble powder on these properties has been discussed.The compressive strength and stressstrain relation were tested for different series prepared by partially replacing cement at proportions of 5%–25%separately.From the data analysis,it was observed that the using of waste marble powder would affect the hydration products and further affect the mechanical properties of concrete,the addition of marble powder that partially replace the cement at particular proportions in concrete is feasible.

Physical and Mechanical Properties of Antifungal Ionic Liquid-Incorporated Dental Tissue Conditioner

Denture stomatitis and fungal infection are commonly found in long-time denture wearer. Ionic liquids have been used as plasticizer and also possess antimicrobial activity. In this study, ionic liquid in form of 1-Decyl-3-methy-limidazolium chloride was incorporated into tissue conditioner (GC Soft-liner TM) to improve antifungal activity. Physical and mechanical properties were evaluated. Compliance was carried out using penetration test according to ISO 10139-1. Weight change, water absorption and solubility were determined by weight measurement. Conventional and nystatin-incorporated tissue conditioner served as controls. Results showed that ionic liquid-incorporated tissue conditioner significantly decreased fungal formation, both in material suspension and on material surface. The penetration depth of all groups tended to reduce over time with no significant difference at each time point. After water immersion, ionic liquid- and nystatin-incorporated tissue conditioner gained weight while conventional group showed weight loss. The percentage of water absorption of conventional group was significantly lower than ionic liquid and nystatin group, while the percentage of water solubility of nystatin group was significantly higher than others. Our work indicated that antifungal ionic liquid-incorporated tissue conditioner met the standard criteria in terms of material compliance. However, further studies including dynamic viscoelastic property are needed before clinical trial or application.

Study on the Structural Characteristics and Physical and Mechanical Properties of Phoebe bournei Thinning Wood

The artificial afforestation of precious Phoebe bournei has been carried out in China.During the cultivation process,thinning wood will be produced.The properties of thinning wood might vary greatly with matured wood and require evaluation for better utilization.The objective of the present study aims to determine the wood structure,fiber morphology,and physical and mechanical properties of the Phoebe bournei thinning wood to help us understand the wood properties and improve its utility value.Three 14-year-old Phoebe bournei were cut from Jindong Forestry Farm of Hunan Province,China.The wood structure and fiber morphology were observed and analyzed with a light microscope and scanning electron microscope.The physical and mechanical properties were tested according to the Chinese national standards.The results showed as follows:(1)The Phoebe bournei thinning wood has a beautiful wood figure and fine texture,whereas the heartwood has not yet formed.(2)It is a diffuse-porous hardwood with small and less pores as well as fine wood rays.(3)The wood fiber is medium length and extremely thin wall thickness.(4)It is low in density and has excellent dimensionally stability.(5)The wood mechanical properties belong to the low to medium class and the comprehensive strength of wood belongs to the medium-strength class.It is concluded that Phoebe bournei thinning wood is suitable for wood carving,handicraft,high-end furniture,and decorative furniture parts.

Impact of mica on geotechnical behavior of weathered granitic soil using macro and micro investigations

The micaceous weathered granitic soil(WGS)is frequently encountered in civil engineering worldwide,unfortunately little information is available regarding how mica affects the physico-mechanical behaviors of WGS.This study prepares reconstituted WGS with different mica contents by removing natural mica in theWGS,and then mixes it with commercial mica powders.The geotechnical behavior as well as the microstructures of the mixtures are characterized.The addition of mica enables the physical indices of WGS to be specific combinations of coarser gradation and high permeability but high Atterberg limits.However,high mica content in WGS was found to be associated with undesirable mechanical properties,including increased compressibility,disintegration,and swelling potential,as well as poor compactability and low effective frictional angle.Microstructural analysis indicates that the influence of mica on the responses of mixtures originates from the intrinsic nature of mica as well as the particle packing being formed withinWGS.Mica exists in the mixture as stacks of plates that form a spongy structure with high compressibility and swelling potential.Pores among the plates give the soil high water retention and high Atterberg limits.Large pores are also generated by soil particles with bridging packing,which enhances the permeability and water-soil interactions upon immersion.This study provides a microlevel understanding of how mica dominates the behavior of WGS and provides new insights into the effective stabilization and improvement of micaceous soils.

Effect of Ultrasound and Xylanase Treatment on the Physical-Mechanical Properties of Bleached Eucalyptus Kraft Pulp

The modification on the fiber structure of bleached eucalyptus kraft pulp is a very attractive alternative for improve- ments in the properties of paper production. The enzymatic treatment by xylanases and ultrassonic treatments modify the characteristics of the fibers, has been reported. Therefore, the purpose of this study was to evaluate the influence of ultrasonic waves as a facilitator of the action of enzymes (hemicellulase) by modifying the physicochemical nature of fiber eucalyptus Kraft pulp, in order to improve the physical and mechanical properties of the paper. But it was observed the that idea of ultrasound acts as facilitator for action of enzymes can’t be affirmed, since in most properties XA-1 and XA-2 were equal statistically. It may be noted that the junction of ultrasound and xylanase provided improves on tensile index, specific elastic modulus and tensile energy absorption and a decrease of tear index on the mechanical properties of handsheet and it increased the opacity when the ultrasound was applied before xylanase.

Characterization of the Physical and Mechanical Properties of the Harrat Ash Shaam Basalt (HASB)/Northeast Jordan

Due to the mass demand for excellent construction materials for infrared and super structures in Jordan, intensive field and laboratory works were carried out to determine the quality of basalt as a source for construction uses or as aggregate materials. Representative basaltic samples were collected from four quarries in Harrat Ash Shaam Basalt (HASB), northeast Jordan (Al-Azraq, Tel-Hassan, Q’a-Khanna and Al-Aritayin). Necessary and accentual quality control tests were carried out on 17 samples of basalt to determine the physical and mechanical properties of target samples, whereas petrographic and chemical analysis for some representative samples have been carried out using a polarizing microscope and X-ray fluorescence (XRF). This study aims to focus on the main engineering characteristics of the basalt rocks and to shed some light on their properties. This work represents the results of petrographic and chemical analysis, tests of abrasion, absorption, specific gravity, unit weight and void ratio, sieve analysis (gradation), soundness, flakiness and elongation indices, pulse velocity and compressive strength. Petrographic studies show that the basalt is characterized by a presence mainly of calcic-plagioclase feldspar, pyroxene-augite and olivine. The composition of the basaltic samples reflects ultrabasic-basic (Basanite-Tholeiitic basalt type). The basalt is characterized by higher specific gravity, lower absorption and medium abrasion loss values, and resistance to corrosion, with medium to high compressive strength. The results of the studied physical and mechanical properties of the basalt that have been tested comply with the standard requirements. In most of the studies, basalt has good physical and mechanical properties that can be used for engineering applications.