Teaching Status and Teaching Reform Ideas of Physical Chemistry Experiments for Food Quality and Safety Major

Physical chemistry experiments are an important branch of chemical experiments.In view of problems and shortcomings in physical chemistry experiment teaching of food quality and safety major in Chengdu University,the teaching methods of physical chemistry experiment course of food quality and safety major were explored and practiced,aiming to arouse students enthusiasm for experiments and cultivate their ability of independent learning,comprehensive thinking and independent problem solving.

Experimental Study on Hydrodynamic Load Characteristics for A Typical Cross-Section of A Submerged Floating Tunnel

The typical cross-sectional form of a submerged floating tunnel plays a significant role in the dynamic response of the tunnel itself,which directly affects the overall design.In this work,a series of experiments involving wave action on a submerged floating tube cross section is reported to study its hydrodynamic load characteristics.Two typical cross section tube cylinders,circular and rectangular,are chosen.Experiments are carried out in a wave flume with waves of relatively low Keulegan-Carpenter(KC)numbers.Three relative depths of submergence of 0,0.25 and 0.5 are chosen.The measured wave forces in regular waves are used to analyze the horizontal force,vertical force and torque,and then the drag coefficient(Cd)and inertia coefficient(Cm)are derived.The results show that the drag coefficients at low KC numbers are large and decrease sharply with increasing KC number.The inertial coefficient Cm values in the vertical direction are about 70%larger than those in the horizontal direction.With an increase in aspect ratio(the ratio of the height to width of the structure),the ratio of inertia coefficient in the horizontal direction to that in the vertical direction increases remarkably.The inertia force coefficient is very sensitive to the submerged water depth and aspect ratio.The existing results may overestimate the actual force value.

Reform and Practice of University Physics Experimental Teaching Based on OBE Concept

Aiming at the problems of unclear teaching objectives,obsolete content,and single method in the experimental teaching of university physics at our university,we have implemented a series of reform initiatives.It mainly includes clarifying the student-centered teaching objectives,optimizing the experimental content,innovating the teaching methods,improving the assessment and evaluation system,and improving the experimental conditions[1,2].After the implementation of the reform,the learning effectiveness of students has been significantly improved,the teaching level of teachers has been significantly enhanced,the curriculum system has been optimized,the efficiency of teaching management has been enhanced,and social recognition has been strengthened.Practice shows that the teaching reform based on the outcome-based education concept effectively improves the quality of university physics experimental teaching and lays the foundation for cultivating innovative talents.

Three-Dimensional Finite Element Numerical Simulation and Physical Experiment for Magnetism-Stress Detecting in Oil Casing

The casing damage has been a big problem in oilfield production. The current detection methods mostly are used after casing damage, which is not very effective. With the rapid development of China's offshore oil industry, the number of offshore oil wells is becoming larger and larger. Because the cost of offshore oil well is very high, the casing damage will cause huge economic losses. What's more, it can also bring serious pollution to marine environment. So the effective methods of detecting casing damage are required badly. The accumulation of stress is the main reason for the casing damage. Magnetic anisotropy technique based on counter magnetostriction effect can detect the stress of casing in real time and help us to find out the hidden dangers in time. It is essential for us to prevent the casing damage from occurring. However, such technique is still in the development stage. Previous studies mostly got the relationship between stress and magnetic signals by physical experiment, and the study of physical mechanism in relative magnetic permeability connecting the stress and magnetic signals is rarely reported. The present paper uses the ANSYS to do the three-dimensional finite element numerical simulation to study how the relative magnetic permeability works for the oil casing model. We find that the quantitative relationship between the stress' s variation and magnetic induction intensity's variation is: Δδ =K* ΔB, K = 8.04×109, which is proved correct by physical experiment.

The Design and Implementation of Virtual Physics Experiment System based on VB Programming

This paper used the virtual reality modeling language （VRML） to establish the 3D virtual experiment instrument model, and by using the visual programming language VB to design and develop a interactive virtual realization experiment platform, the interface has friendly interface, stable operation, strong practicability like with the Windows style, is a kind of reform for the traditional physics experiment teaching mode. The system has practical use value, also has reference value for the reform and modernization of other experimental courses.

Designing physical experiment about characters of fuel cells

Currently, proton exchange membrane fuel cells are the most widely used fuel cell technology, In this article the function of fuel cells is briefly introduced. Certain characters of fuel cells are investigated through measuring the relation between electric current, voltage and product. A series of physics experiments using fuel cells is designed.

Experimental observation on water entry of a sphere in regular wave

This paper presents a novel experiment to observe the whole water entry process of a free-falling sphere into a regular wave.A time-accurate synchronizing system modulates the moment elaborately to ensure the sphere impacting onto the water surface at the desirable wave phase.Four high-speed cameras focus locally to measure the high-precision size of the cavity evolution.Meanwhile,the aggregated field view of the camera array covers both the splash above the free surface and the entire cavity in the wave.The detailed methodologies are described and verified for the hardware set-up and the image post-processing.The theoretical maximum deviation is 1.7%on the space scale.The integral morphology of the cavity is captured precisely in the coordinate system during the sphere penetrates through the water at four representative wave phases and the still water.The result shows that the horizontal velocity of the fluid particle in the wave impels the cavity and changes the shape distinctly.Notably,the wave motion causes the cavity to pinch offearlier at the wave trough phase and later at the wave crest phase than in the still water.The wave motion influences the falling process of the sphere slightly in the present parameters.

The influence of inter-band rock on rib spalling in longwall panel with large mining height

In order to improve rib stability,failure criteria and instability mode of a thick coal seam with inter-band rock layer are analysed in this study.A three-dimensional mechanical model is established for the rib by considering the rock layer.A safety factor is defined foy the rib,and it is observed that the safety factor exhibits a positive correlation with the thickness and strength of the inter-band rock.A calculation method for determining critical parameters of the rock layer is presented to ensure the rib stability.It is revealed that incomplete propagation of the fracture at the hard rock constitutes a fundamental prerequisite for ensuring the rib stability.The influence of the position of the inter-band rock in the coal seam on failure mechanism of the rib was thoroughly investigated by developing a series of physical models for the rib at the face area.The best position for the inter-band rock in the coal seam is at a height of 1.5 m away from the roof line,which tends to provide a good stability state for the rib.For different inter-band rock positions,two ways of controlling rib by increasing supports stiffness and flexible grouting reinforcement are proposed.

Sliding and damming properties of granular debris with different geometric configurations and grain size distributions

Granular debris plays a significant role in determining damming deposit characteristics. An indepth understanding of how variations in grain size distribution(GSD) and geometric configurations impact the behavior of granular debris during the occurrence of granular debris is essential for precise assessment and effective mitigation of landslide hazards in mountainous terrains. This research aims to investigate the impact of GSD and geometric configurations on sliding and damming properties through laboratory experiments. The geometric configurations were categorized into three categories based on the spatial distribution of maximum volume: located at the front(Type Ⅰ), middle(Type Ⅱ), and rear(Type Ⅲ) of the granular debris. Our experimental findings highlight that the sliding and damming processes primarily depend on the interaction among the geometric configuration, grain size, and GSD in granular debris. Different sliding and damming mechanisms across various geometric configurations induce variability in motion parameters and deposition patterns. For Type Ⅰ configurations, the front debris functions as the critical and primary driving component, with energy dissipation primarily occurring through inter-grain interactions. In contrast, Type Ⅱ configurations feature the middle debris as the dominant driving component, experiencing hindrance from the front debris and propulsion from the rear, leading to complex alterations in sliding motion. Here, energy dissipation arises from a combination of inter-grain and grain-substrate interactions. Lastly, in Type Ⅲ configurations, both the middle and rear debris serve as the main driving components, with the rear sliding debris impeded by the front. In this case, energy dissipation predominantly results from grainsubstrate interaction. Moreover, we have quantitatively demonstrated that the inverse grading in damming deposits, where coarse grain moves upward and fine grain moves downward, is primarily caused by grain sorting due to collisions among the grains and between the grain and the base. The impact of grain on the horizontal channel further aids grain sorting and contributes to inverse grading. The proposed classification of three geometric configurations in our study enhances the understanding of damming properties from the view of mechanism, which provides valuable insights for related study about damming granular debris.

Permeability Estimation of Shale Oil Reservoir with Laboratory-derived Data: A Case Study of the Chang 7 Member in Ordos Basin

The shale oil reservoir within the Yanchang Formations of Ordos Basin harbors substantial oil and gas resources and has recently emerged as the primary focus of unconventional oil and gas exploration and development.Due to its complex pore and throat structure,pronounced heterogeneity,and tight reservoir characteristics,the techniques for conventional oil and gas exploration and production face challenges in comprehensive implementation,also indicating that as a vital parameter for evaluating the physical properties of a reservoir,permeability cannot be effectively estimated.This study selects 21 tight sandstone samples from the Q area within the shale oil formations of Ordos Basin.We systematically conduct the experiments to measure porosity,permeability,ultrasonic wave velocities,and resistivity at varying confining pressures.Results reveal that these measurements exhibit nonlinear changes in response to effective pressure.By using these experimental data and effective medium model,empirical relationships between P-and S-wave velocities,permeability and resistivity and effective pressure are established at logging and seismic scales.Furthermore,relationships between P-wave impedance and permeability,and resistivity and permeability are determined.A comparison between the predicted permeability and logging data demonstrates that the impedance–permeability relationship yields better results in contrast to those of resistivity–permeability relationship.These relationships are further applied to the seismic interpretation of shale oil reservoir in the target layer,enabling the permeability profile predictions based on inverse P-wave impedance.The predicted results are evaluated with actual production data,revealing a better agreement between predicted results and logging data and productivity.

Formation mechanism of fault accommodation zones under combined stress in graben basin:Implications from geomechanical modeling

A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,indicating the potential exploration target and petroleum accumulation areas.This study aims to analyze the formation mechanism and development of fault accommodation zones under combined stress by a numerical simulation method considering geomechanical modeling.Using three-dimensional(3-D)seismic interpretation and fractal dimension method,exampled with the Dongxin fault zone,the fault activity and fault combination pattern were conducted to quantitatively characterize the activity difference in fault accommodation zones.Combined with mechanical experiment test,a geomehcanical model was established for fault accommodation zones in a graben basin.Integrating the paleostress numerical simulations and structural physical simulation experiment,the developmental characteristics and genetic mechanism of fault accommodation zones were summarized.Influenced by multi movements and combined stresses,three significant tectonic evolution stages of the Dongxing Fault Zone(DXFZ)were distinguished:During the E_(s)^(3)sedimentary period,the large difference in the stress,strain,and rupture distribution in various faults were significant,and this stage was the key generation period for the prototype of the DXFZ,including the FAZ between large-scale faults.During the E_(s)^(2)sedimentary period,the EW-trending symmetric with opposite dipping normal faults and the NE-SW trending faults with large scale were furtherly developed.The junction area of two secondary normal faults were prone to be ruptured,performing significant period for inheriting and developing characteristics of fault accommodation zones.During the Es1 sedimentary period,the high-order faults in the DXFZ exhibited the obvious fault depressions and strike-slip activity,and the fault accommodation zones were furtherly inherited and developed.This stage was the molded and formative period of the FAZ,the low-order faults,and the depression in the DXFZ.

Maximum initial primary wave model for low-Froude-number reservoir landslides based on wave theory

The impulse waves induced by large-reservoir landslides can be characterized by a low Froude number.However,systematic research on predictive models specifically targeting the initial primary wave is lacking.Taking the Shuipingzi 1#landslide that occurred in the Baihetan Reservoir area of the Jinsha River in China as an engineering example,this study established a large-scale physical model(with dimensions of 30 m×29 m×3.5 m at a scale of 1:150)and conducted scaled experiments on 3D landslide-induced impulse waves.During the process in which a sliding mass displaced and compressed a body of water to generate waves,the maximum initial wave amplitude was found to be positively correlated with the sliding velocity and the volume of the landslide.With the increase in the water depth,the wave amplitude initially increased and then decreased.The duration of pressure exertion by the sliding mass at its maximum velocity directly correlated with an elevated wave amplitude.Based on the theories of low-amplitude waves and energy conservation,while considering the energy conversion efficiency,a predictive model for the initial wave amplitude was derived.This model could fit and validate the functions of wavelength and wave velocity.The accuracy of the initial wave amplitude was verified using physical experiment data,with a prediction accuracy for the maximum initial wave amplitude reaching 90%.The conversion efficiency(η)directly determined the accuracy of the estimation formula.Under clear conditions for landslide-induced impulse wave generation,estimating the value ofηthrough analogy cases was feasible.This study has derived the landslide-induced impulse waves amplitude prediction formula from the standpoints of wave theory and energy conservation,with greater consideration given to the intrinsic characteristics in the formation process of landslide-induced impulse waves,thereby enhancing the applicability and extensibility of the formula.This can facilitate the development of empirical estimation methods for landslide-induced impulse waves toward universality.

Calculating the number of radial cracks around a wellbore fractured by liquid CO2 phase transition blasting technology

Integrating liquid CO_(2)phase transition blasting(LCPTB)technology with hydraulic fracturing(HF)methods can help reduce wellbore damage,create multiple radial fractures,and establish a complex fracture network.This approach significantly increases the recovery efficiency of low-permeability oil and gas fields.Accurately calculating the number of fractures caused by LCPTB is necessary to predict production enhancement effects and optimize subsequent HF designs.However,few studies are reported on large-scale physical model experiments in terms of a method for calculating the fracture number.This study analyzed the initiation and propagation of cracks under LCPTB,derived a calculation formula for crack propagation radius under stress waves,and then proposed a new,fast,and accurate method for calculating the fracture number using the principle of mass conservation.Through ten rock-breaking tests using LCPTB,the study confirmed the effectiveness of the proposed calculation approach and elucidated the variation rule of explosion pressure,rock-breaking scenario,and the impact of varying parameters on fracture number.The results show that the new calculation method is suitable for fracturing technologies with high pressure rates.Recommendations include enlarging the diameter of the fracturing tube and increasing the liquid CO2 mass in the tube to enhance fracture effectiveness.Moreover,the method can be applied to other fracturing technologies,such as explosive fracturing(EF)within HF formations,indicating its broader applicability and potential impact on optimizing unconventional resource extraction technologies.

Experimental Investigation of Wave Load and Run-up on the Composite Bucket Foundation Influenced by Regular Waves

In the design of wind turbine foundations for offshore wind farms, the wave load and run-up slamming on the supporting structure are the quantities that need to be considered. Because of a special arc transition, the interaction between the wave field and the composite bucket foundation(CBF) becomes complicated. In this study, the hydrodynamic characteristics, including wave pressure, load, upwelling, and run-up, around the arc transition of a CBF influenced by regular waves are investigated through physical tests at Shandong Provincial Key Laboratory of Ocean Engineering, Ocean University of China. The distributions of the wave pressures and upwelling ratios around the CBF are described, and the relationship between the wave load and the wave parameters is discussed. New formulae based on the velocity stagnation head theory with linear wave theory and the second-order Stokes wave theory for wave kinematics are proposed to estimate the wave run-up. Moreover, the multiple regression method with nonlinear technology is employed to deduce an empirical formula for predicting run-up heights. Results show that the non-dimensional wave load increases with the increase in the values of the wave scattering parameter and relative wave height. The wave upwelling height is high in front of the CBF and has the lowest value at an angle of 135? with the incoming wave direction. The performance of the new formulae proposed in this study is compared using statistical indices to demonstrate that a good fit is obtained by the multiple regression method and the analytical model based on the velocity stagnation head theory is underdeveloped.

Numerical simulation of non-Archie electrophysical property of saturated rock with lattice Boltzmann method

The electrophysical property of saturated rocks is very important for reservoir identification and evaluation. In this paper, the lattice Boltzmann method （LBM） was used to study the electrophysical property of rock saturated with fluid because of its advantages over conventional numerical approaches in handling complex pore geometry and boundary conditions. The digital core model was constructed through the accumulation of matrix grains based on their radius distribution obtained by the measurements of core samples. The flow of electrical current through the core model saturated with oil and water was simulated on the mesoscopic scale to reveal the non-Archie relationship between resistivity index and water saturation （I-Sw）. The results from LBM simulation and laboratory measurements demonstrated that the I-Sw relation in the range of low water saturation was generally not a straight line in the log-log coordinates as described by the Archie equation. We thus developed a new equation based on numerical simulation and physical experiments. This new equation was used to fit the data from laboratory core measurements and previously published data. Determination of fluid saturation and reservoir evaluation could be significantly improved by using the new equation.

Western fault zone of South China Sea and its physical simulation evidences

The western fault zone of the South China Sea is a strike-slip fault system and consists of four typical strike-slip faults. It is the western border of the South China Sea. The formation of the system is due to the extrusion of Indo - China Peninsula caused by the collision of India with Tibet and the spreading of the South China Sea in Cenozoic. There are five episodes of tectonic movement along this fault zone, which plays an important role in the Cenozoic evolution of the South China Sea. By the physical modeling experiments, it can be seen the strike-slip fault undergoes the sinistral and dextral movement due to the relative movement velocity change between the South China Sea block and the Indo - China block. The fault zone controls the evolution of the pull basins locating in the west of the South China Sea.

Overlying strata movement of recovering standing pillars with solid backfilling by physical simulation

To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.The results show that:(i) The covering-rock mechanics of the overly strata comes from "two-arch structures + hinged girder + bend beam" to "backfilling material + hinged girder + bent beam" by increasing the fill ratio from 0%to 85%,the beginning of overlying strata movement appears later and the total duration of subsidence velocity increased from zero to the highest value increases.The trend of "single polarization" of the subsidence velocity curves becomes noticeable and the velocity variation trend becomes stable,(ii) The equiponderate aeolian sand was added to improve the anti-pressure ability of the loess,and the corresponding ground processing & transportation system was designed.

Physical Model of Drying Shrinkage of Recycled Aggregate Concrete

We prepared concretes（RC0, RC30, and RC100） with three different mixes. The poresize distribution parameters of RAC were examined by high-precision mercury intrusion method（MIM） and nuclear magnetic resonance（NMR） imaging. A capillary-bundle physical model with random-distribution pores（improved model, IM） was established according to the parameters, and dry-shrinkage strain values were calculated and verified. Results show that in all pore types, capillary pores, and gel pores have the greatest impacts on concrete shrinkage, especially for pores 2.5-50 and 50-100 nm in size. The median radii are 34.2, 31, and 34 nm for RC0, RC30, and RC100, respectively. Moreover, the internal micropore size distribution of RC0 differs from that of RC30 and RC100, and the pore descriptions of MIM and NMR are consistent both in theory and in practice. Compared with the traditional capillary-bundle model, the calculated results of IM have higher accuracy as demonstrated by experimental verifi cation.

Hydrodynamic Performance of A Dual-Floater Integrated System Com-bining Hybrid WECs and Floating Breakwaters

The high investment and low return of wave energy converters(WECs)seriously hamper their large-scale commercial application.The integration of WECs and floating breakwaters is conducive to enhance the competitiveness of wave energy conversion.The objective of this paper is to investigate the hydrodynamic performance of a WEC-breakwater integrated system combining an upstream oscillating water column(OWC)and a downstream oscillating buoy(OB)via numerical simulations and physical experiments.A nonlinear numerical wave flume using Star-CCM+software is employed to obtain calculated results,where a tiny transverse gap is set between the flume wall and the block surface to simulate a similar two-dimensional(2D)model.The corresponding physical experiments are also carried out in a practical wave flume to verified the numerical results.The comparison of the isolated and hybrid system shows that the hybrid design leads to the decreased conversion efficiency of each WEC,but improves the transmission performance of the hybrid system.The wave resonance between two devices causes the abrupt reduction of OWC efficiency and a positive correlation exists with the OB efficiency.The total efficiency of the hybrid system is raised by an optimal opening ratio,a shallow OWC draft and a short spacing distance.Except for the OWC draft,other design parameters have weak effect on the wave attenuation of the hybrid system.This paper can help understand hydrodynamics of the hybrid WECs integrated with breakwaters and improve their performances.

Experiments on Channel Evolution due to Dam Removal in Taiwan

Due to safety concerns and habitat restoration for landlocked salmon,a 13-m high check dam on Chijiawan Creek was removed in late May 2011 in Taiwan.We conducted experiments to understand channel evolution of different scenarios.We further compared our experimental results of riverbed elevation changes with the analytical solutions derived from the diffusion equation and field dynamics as well after the creek experienced the first flood event.The results indicated that magnitude of discharges and notch size are dominant factors in resulting channel evolution.While the largest differences between grain size distribution are associated with discharge,the largest differences in net change in upstream volume are associated with notch size.While the theoretical equation could help understand the channel change after dam removal,it only explained the evolution closer to the dam.The physical experiments,on the other hand,provided insights especially with regard to comparing alternative proposed management actions.The discrepancies between predicted and actual outcome highlight more needed inputs for future dam-removal assessments.