2-D crustal structure and velocity ratio are obtained by processing S-wave data from two wide-angle reflec-tion/refraction profiles in and around Jiashi in northeastern Pamir, with the result of P-wave data taken into...2-D crustal structure and velocity ratio are obtained by processing S-wave data from two wide-angle reflec-tion/refraction profiles in and around Jiashi in northeastern Pamir, with the result of P-wave data taken into con-sideration. The result shows that: 1) Average crustal velocity ratio is obviously higher in Tarim block than in West Kunlun Mts. and Tianshan fold zone, which reflects its crustal physical property of 'hardness' and stability. The relatively low but normai velocity ratio (Poisson's ratio) of the lower crust indicates that the 'downward thrusting' of Tarim basin is the main feature of crustal movement in this area. 2) The rock layer in the upper crust of Tianshan fold zone is relatively 'soft', which makes it prone to rupture and stress energy release. This is the primary tectonic factor for the concentration of small earthquakes in this area. 3) Jiashi is located right over the apex or the inflection point of the updoming lower crustal interface C and the crust-mantle boundary, which is the deep struc-tural background for the occurrence of strong earthquakes. The alternate variation of vp/vs near the block bounda-ries and the complicated configuration of the interfaces in the upper and middie part of the upper crust form a par-ticular structural environment for the Jiashi strong earthquake swarm. vp/vs is comparatively high and shear modulus is low at the focal region, which may be the main reason for the low stress drop of the Jiashi strong earthquake swarm.展开更多
We report on the single crystal growth and superconducting properties of PbTaSe2 with the non-centrosymmetric crystal structure. By using the chemicM vapor transport technique, centimeter-size single crystals are succ...We report on the single crystal growth and superconducting properties of PbTaSe2 with the non-centrosymmetric crystal structure. By using the chemicM vapor transport technique, centimeter-size single crystals are success- fully obtained. The measurement of temperature dependence of electricaJ resistivity p(T) in both normal and superconducting states indicates a quasi-two-dimensional electronic state in contrast to that of polycrystalline samples. Specific heat C(T) measurement reveals a bulk superconductivity with Tc ≈ 3.75K and a specific heat jump ratio of 1.42. All these results are in agreement with a moderately electron-phonon coupled, type-g Bardeen-Cooper-Schrieffer superconductor.展开更多
From the viewpoints of coexistence theory of the slag structure, the investigation on the structural units of MnO-SiO2 system and the chemical reactions between them has been carried out. The relationships between the...From the viewpoints of coexistence theory of the slag structure, the investigation on the structural units of MnO-SiO2 system and the chemical reactions between them has been carried out. The relationships between the physical propenies of the slag and the mass action concentrations of its have been set up at certain temperature and slag composition range, which based on the thermodynamic data of the chemtical reactions between the units and the method of linear regression. The calculated data from the model are in good agreement with the measured results. These calculated values are more accurate and systematic than those from other expirical and semi-expirical formulas used at present.展开更多
Biochar is widely used to improve soil physical properties and carbon sequestration. However, few studies focuse on the impact of maize stalk biochar on labile organic carbon(LOC) pool and the relationship between phy...Biochar is widely used to improve soil physical properties and carbon sequestration. However, few studies focuse on the impact of maize stalk biochar on labile organic carbon(LOC) pool and the relationship between physical properties and LOC fractions. A field positioning experiment was performed in Mollisols region of Northeast China to evaluate the influence of maize stalk biochar on the spatial distribution and temporal changes of physical properties and LOC fractions. Maize stalk biochar treatments included C1(1.5 kg·hm^(-2)), C2(3 kg·hm^(-2)), C3(15 kg·hm^(-2)), C4(30 kg·hm^(-2)), and CK(0). The results showed that maize stalk biochar increased soil water contents(SWC) and soil porosity(SP), but reduced bulk density(BD). Maize stalk biochar reduced dissolved organic carbon(DOC) contents in the 0-20 cm soil layer, ranging from 0.25 g·kg^(-1) to 0.31 g·kg^(-1) in harvest period, while increased in the 20-40 cm soil layer. In addition, the application of biochar had a significant impact on the spatial distribution and temporal change of SWC, BD, SP, DOC, hot-water extractable carbon(HWC), acid hydrolyzed organic carbon(AHC Ⅰ, Ⅱ), and readily oxidized organic carbon(ROC). High amounts of maize stalk biochar up-regulated the contents of soil organic carbon SOC, HWC, AHC Ⅰ, AHC Ⅱ, and ROC. In addition, SWC and SP were the key physical factors to affect LOC fractions. In conclusions, maize stalk biochar could improve physical properties, and then influence LOC fractions, and maize stalk biochar could be used as an organic amendment for restoring degraded soils governed by their rates of addition.展开更多
In recent years,the exploration of seabed has been intensified,but the submarine soils of silt and sand in the Yellow Sea area have not been well investigated so far.In this study,the physical and mechanical propertie...In recent years,the exploration of seabed has been intensified,but the submarine soils of silt and sand in the Yellow Sea area have not been well investigated so far.In this study,the physical and mechanical properties of silt and sand from the Yellow Sea were measured using a direct shear apparatus and their microstructures were observed using a scanning electron microscope.The test results suggest that the shear strength of silt and sand increases linearly with the increase of normal stress.Based on the direct shear test,the scanning electron microscope was used to observe the section surface of sand.It is observed that the section surface becomes rough,with many“V”‐shaped cracks.Many particles appear on the surface of the silt structure and tend to be disintegrated.The X‐ray diffraction experiment reveals that the sand and silt have different compositions.The shear strength of sand is slightly greater than that of silt under high stress,which is related to the shape of soil particles and the mineral composition.These results can be a reference for further study of other soils in the Yellow Sea;meanwhile,they can serve as soil parameters for the stability and durability analyses of offshore infrastructure construction.展开更多
Salvaged cow horns from slaughterhouses have been transformed into fine particles for a physical characterization that has led us to determine the humidity rate (2.34% ± 0.054%), the actual density situated betwe...Salvaged cow horns from slaughterhouses have been transformed into fine particles for a physical characterization that has led us to determine the humidity rate (2.34% ± 0.054%), the actual density situated between 0.586 g/cm<sup>3</sup> and 0.732 g/cm<sup>3</sup>, the swelling rate (12%), and one chemical characterization that permitted us to determine the rate of dry matters (97.05%), of mineral matters (2.5%), of protein matters (94.52%). From these weak values, it can easily be seen that cow horn case doesn’t absorb much water and improve the mechanical characteristics of the composite;the high rate of protein shows that keratin which is the structural molecule favors its gripping as reinforcing element in the manufacturing of composite materials.展开更多
Changqing old oilfield Jurassic reservoir's average calibration recovery is 24.7%,with geological reserves recovery of 16.6%,water cut of 65.2%.And most of Jurassic reservoirs are in the middle and later field lif...Changqing old oilfield Jurassic reservoir's average calibration recovery is 24.7%,with geological reserves recovery of 16.6%,water cut of 65.2%.And most of Jurassic reservoirs are in the middle and later field life,part of them has entered the high water cut and high recovery stage.Traditional water flooding way for improving oil recovery becomes more difficult,and new method has to be considered.Maling oilfield BS district is a typical representative,with high water cut of 90.8%,high recovery percent of 26.1%and low oil recovery rate of 0.25%.To explore the new way to improve oil recovery,the polymer and surfactant(SP for short)important pilot test has been developed.The low permeability reservoir indoor core data in high water cut stage and inspection well results indicate that the reservoir permeability,pore combination characteristics and pore type changed greatly after long-term water flooding development.These changes bring more difficulties to the continue development,especially the high injection pressure,which can cause other problems for well pattern infilling and EOR.This paper takes the high injection pressure problem of Maling BS district Jurassic reservoir for example,analyzes the physical property change law on the following aspects:the development mode in the past,core analysis,formation sensitivity,interstitial matter,well test interpretation results,in order to help to further effective development and provide important parameters for tertiary oil recovery technique for similar reservoirs and others.展开更多
Solid physical properties are vital for the design, optimization, and scale-up of gas–liquid–solid multiphase reactors. The complex and interactional effects of the solid physical properties, including particle diam...Solid physical properties are vital for the design, optimization, and scale-up of gas–liquid–solid multiphase reactors. The complex and interactional effects of the solid physical properties, including particle diameter, density, wettability, and sphericity, on the hydrodynamic behaviors in a new external airlift loop reactor(EALR) integrating mixing and separation are decoupled in this work. Two semi-empirical equations are proposed and validated to predict the overall gas holdup and liquid circulating velocity satisfactorily, and then the individual influence of such solid physical properties is further investigated. The results demonstrate that both the overall gas holdup in the riser and the liquid circulating velocity in the downcomer increase with the contact angle, but decrease with particle size, density, and sphericity.Additionally, the impact of the particle size on the liquid circulating velocity is also profoundly revealed on a micro-level considering the particle size distribution. Moreover, the axial solid concentration distribution is discussed, and the uniformity of the slurry is described by the mixing index of the solid particles. The results show that a more homogeneous mixture can be achieved by adding finer particles other than attaining violent turbulence. Therefore, this work lays a foundation for the design, scale-up, and industrialization of the EALRs.展开更多
Knowledge about the spatial distribution of the soil physical and mechanical properties is crucial for soil management,water yield,and sustainability at the watershed scale;however,the lack of soil data hinders the ap...Knowledge about the spatial distribution of the soil physical and mechanical properties is crucial for soil management,water yield,and sustainability at the watershed scale;however,the lack of soil data hinders the application of this tool,thus urging the need to estimate soil properties and consequently,to perform the spatial distribution.This research attempted to examine the proficiency of three machine learning methods(RF:Random Forest;Cubist:Regression Tree;and SVM:Support Vector Machine)to predict soil physical and mechanical properties,saturated hydraulic conductivity(Ks),Cohesion measured by fall-cone at the saturated(Psat)and dry(Pdry)states,hardness index(HI)and dry shear strength(SS)by integrating environmental variables and soil features in the Zayandeh-Rood dam watershed,central Iran.To determine the best combination of input variables,three scenarios were examined as follows:scenarioⅠ,terrain attributes derivative from a digital elevation model(DEM)+remotely sensed data;scenarioⅡ,covariates of scenarioⅠ+selected climatic data and some thematic maps;scenarioⅢ,covariates in scenarioⅡ+intrinsic soil properties(Clay,Silt,Sand,bulk density(BD),soil organic matter(SOM),calcium carbonate equivalent(CCE),mean weight diameter(MWD)and geometric weight diameter(GWD)).The results showed that for Ks,Psat Pdry and SS,the best performance was found by the RF model in the third scenario,with R2=0.53,0.32,0.31 and 0.41,respectively,while for soil hardness index(HI),Cubist model in the third scenario with R2=0.25 showed the highest performance.For predicting Ks and Psat,soil characteristics(i.e.clay and soil SOM and BD),and land use were the most important variables.For predicting Pdry,HI,and SS,some topographical characteristics(Valley depth,catchment area,mltiresolution of ridge top flatness index),and some soil characteristics(i.e.clay,SOM and MWD)were the most important input variables.The results of this research present moderate accuracy,however,the methodology employed provides quick and costeffective information serving as the scientific basis for decision-making goals.展开更多
The element geochemical characteristics and diagenetic alteration products of tuffaceous components in sandstone reservoirs of Paleogene Wenchang Formation in typical subsags of the Huizhou-Lufeng area of the Zhu I De...The element geochemical characteristics and diagenetic alteration products of tuffaceous components in sandstone reservoirs of Paleogene Wenchang Formation in typical subsags of the Huizhou-Lufeng area of the Zhu I Depression,Pearl River Mouth Basin,were identified through microscopic analysis and quantitative analysis of main and trace elements.The impacts of dissolution of different tuffaceous components on physical properties of reservoirs were discussed through quantitative characterization of reservoir physical properties.The results show that there are mainly four types of tuffaceous components in the study area,which are acidic,intermediate,basic and alkaline tuffaceous components.The acidic tuffaceous components evolved in a process of strong alteration and weak dissolution of alteration products,with a large amount of kaolinite precipitated during alteration to disenable the improvement of porosity and permeability.The intermediate and alkaline tuffaceous components evolved in a process of strong dissolution of tuffaceous components and strong alteration of residual tuffaceous components;the dissolution of tuffaceous components created intergranular pores,but the alteration products such as autogenic quartz,apatite and illite deteriorated the pore structure;ultimately,the dissolution of tuffaceous components resulted in the increase of porosity but no increase of permeability of the reservoir.The basic tuffaceous components dominantly evolved in a process of dissolution of tuffaceous components to strong dissolution of alteration products;both tuffaceous components between particles and laumontite generated from alteration can be strongly dissolved to create pores;thus,the dissolution of tuffaceous components can significantly increase the physical properties of the reservoir.展开更多
With the increasing scarcity of Earth’s resources and the development of space science and technology,the exploration, development, and utilization of deep space-specific material resources(minerals, water ice, volat...With the increasing scarcity of Earth’s resources and the development of space science and technology,the exploration, development, and utilization of deep space-specific material resources(minerals, water ice, volatile compounds, etc.) are not only important to supplement the resources and reserves on Earth but also provide a material foundation for establishing extraterrestrial research bases. To achieve large depth in-situ condition-preserved coring(ICP-Coring) in the extreme lunar environment, first, lunar rock simulant was selected(SZU-1), which has a material composition, element distribution, and physical and mechanical properties that are approximately equivalent to those of lunar mare basalt. Second, the influence of the lunar-based in-situ environment on the phase, microstructure, and thermal physical properties(specific heat capacity, thermal conductivity, thermal diffusivity, and thermal expansion coefficient)of SZU-1 was explored and compared with the measured lunar rock data. It was found that in an air atmosphere, low temperature has a more pronounced effect on the relative content of olivine than other temperatures, while in a vacuum atmosphere, the relative contents of olivine and anorthite are significantly affected only at temperatures of approximately-20 and 200 ℃. When the vacuum level is less than100 Pa, the contribution of air conduction can be almost neglected, whereas it becomes dominant above this threshold. Additionally, as the testing temperature increases, the surface of SZU-1 exhibits increased microcracking, fracture opening, and unevenness, while the specific heat capacity, thermal conductivity,and thermal expansion coefficient show nonlinear increases. Conversely, the thermal diffusivity exhibits a nonlinear decreasing trend. The relationship between thermal conductivity, thermal diffusivity, and temperature can be effectively described by an exponential function(R^(2)>0.98). The research results are consistent with previous studies on real lunar rocks. These research findings are expected to be applied in the development of the test and analysis systems of ICP-Coring in a lunar environment and the exploration of the mechanism of machine-rock interaction in the in-situ drilling and coring process.展开更多
This study characterized and compared the physical and emulsifying properties of pea protein(PP)and its modified proteins(ultrasound treated-PP(PPU),flaxseed gum(FG)treated PP(PPFG)and ultrasound treated-PPFG(PPFGU))....This study characterized and compared the physical and emulsifying properties of pea protein(PP)and its modified proteins(ultrasound treated-PP(PPU),flaxseed gum(FG)treated PP(PPFG)and ultrasound treated-PPFG(PPFGU)).The results showed FG triggered the formation of loosely attached complex with PP via physical modification under gentle magnetic stirring at pH 7.0,while ultrasound played an important role in reducing protein size,increasing surface hydrophobicity and molecular fluidity onto oil-water interface.So ultrasound further enhanced the interaction of PP with FG,and produced the PPFGU complex with smaller droplet size,higherζ-potential and lower turbidity.Further,combination of FG and ultrasound improved the physical properties of PP with higher viscosity,stiffer gels(defined as higher elastic modulus),stronger hydrophobic properties,better thermal stability,and fast protein absorption rate.Therefore,the PPFGU coarse emulsion performed highest emulsifying activity index(EAI)and emulsion stability index(ESI)that the stabilized nanoemulsion obtained smallest droplet size,higherζ-potential,and longest storage stability.The combination of FG and ultrasonic treatment will be an effective approach to improving the emulsifying property and thermal stability of PP,which can be considered as a potential plant-based emulsifier applied in the food industry.展开更多
Cements are widely developed in clastic rock-originated weathering crust(CWC)reservoirs in the Kexia region along the northwestern margin of the Junggar Basin and significantly affect reservoir physical properties and...Cements are widely developed in clastic rock-originated weathering crust(CWC)reservoirs in the Kexia region along the northwestern margin of the Junggar Basin and significantly affect reservoir physical properties and oil and gas distribution in this area.Focusing on the CWC reservoirs at the top of both the Permian Jiamuhe Formation and the Triassic Karamay Formation,this study analyzed the types and characteristics of cements in the reservoirs and explored their effects on reservoir physical properties based on thin sections,SEM images,XRD results,and tests of physical properties.The main results are as follows.The cements in the CWC reservoirs in Kexia region mainly consist of carbonate minerals(41.5%),clay minerals(27.8%)and zeolite minerals(30%),as well as small amount of siliceous minerals.Among them,the carbonate minerals are dominated by siderite and calcite,the clay minerals mainly include kaolinite,interstratified illite/smectite(I/S)and chlorite,and the zeolite minerals primarily comprise heulandite and laumontite.These different types of multiphase cements are generally paragenetic or associated and affect reservoir physical properties to different degrees.Specifically,the carbonate and clay cements of the early diagenetic stage reduced the reservoirs’average porosity from 21%to 15%.The dissolution of some carbonate and zeolite cements in the early A substage of the middle diagenetic stage restored the average porosity to 18%,and the cementation in the late A substage decreased the average porosity to 13%again,of which about 4%was reduced by carbonate cements.The average porosity of the CWC reservoirs gradually decreased to the current value of approximately 10%in the B substage of the middle diagenetic stage.The impact of cementation on the CWC reservoirs can reach as far as 70 m below the unconformity.Moreover,the types and contents of cements vary with their depth below the unconformity surface,leading to the development of multiple zones with high cement content and the differentiated oil and gas distribution.展开更多
The accurate assessment of soil properties is a crucial factor for composing and implementing reclamation plans. The main objective of this study was to evaluate soil chemical and physical properties and calculate the...The accurate assessment of soil properties is a crucial factor for composing and implementing reclamation plans. The main objective of this study was to evaluate soil chemical and physical properties and calculate the chemical and fertility index for assisting land reclamation in Toshka area. The Toshka area is located between latitudes 31°32'N and 31°36'N and longitudes 32°40'E and 32°60'E. GIS was used to select 16 sites. The results revealed the soil has undesirable characteristics. The soil pH ranged from slightly alkaline to moderately alkaline. Furthermore, it was characterized as saline (with a ECe of 4.65 - 11.45 dS⋅m<sup>−1</sup>) and moderately calcareous soil (with CaCO<sub>3</sub> at 11.85% - 17.20%). The soil had a low soil organic matter content which did not exceed 0.18%. The soil was dominated by a sandy loam texture (62.50%) followed by a sandy clay loam texture (18.75%). The bulk density, total soil porosity and saturated hydraulic conductivity values varied with 1.38 - 1.55 Mg⋅cm<sup>−3</sup>, 41.85% - 48.45% and 1.20 - 3.34 cm⋅h<sup>−1</sup>, respectively. The chemical index ranged from low to moderate quality. The correlations between the parameters osculated between negative and positive. Therefore, the soil may be reclaimed if the soil properties are improved and crop selection is optimized for this soil.展开更多
Soil physical properties are important indicators of the potential for agricultural production.Our objective was to evaluate the effects of long-term inputs of green manures on physical properties of a reddish paddy s...Soil physical properties are important indicators of the potential for agricultural production.Our objective was to evaluate the effects of long-term inputs of green manures on physical properties of a reddish paddy soil(Fe-Typic Hapli-Stagnic Anthrosols) under a double cropping system.The common cropping pattern before the study was early-late rice-fallow(winter).The field treatments included rice-rice-fallow(R-R-WF),rice-rice-rape(R-R-RP),rice-rice-Chinese milk vetch(RR-MV),and rice-rice-ryegrass(R-R-RG).The rape,Chinese milk vetch and ryegrass were all incorporated as green manures 15 d before early rice transplanting during the following year.The soil bulk density in all green manure treatments was significantly reduced compared with the winter fallow treatment.Soil porosity with green manure applications was significantly higher than that under the winter fallow.The green manure treatments had higher 0.25-5 mm water stable aggregates and aggregates stabilities in the plow layer(0-15 cm depth) compared with the fallow treatment.The mean weight diameter(MWD) and normalized mean weight diameter(NMWD) of aggregates in the green manure treatment were larger than that with the winter fallow.Soil given green manure retained both a higher water holding capacity in the plow layer soil,and a larger volume of moisture at all matric potentials(-10,-33 and-100 kPa).We conclude that the management of double-rice fields in southern central China should be encouraged to use green manures along with chemical fertilizers to increase SOC content,improve soil physical properties and soil fertility.展开更多
The coalbed methane (CBM) resources in North China amounts up to 60% of total resources in China. North China is the most important CBM accumulation area in China. The coal beds of the Upper Paleozoic Taiyuan and Shan...The coalbed methane (CBM) resources in North China amounts up to 60% of total resources in China. North China is the most important CBM accumulation area in China. The coal beds of the Upper Paleozoic Taiyuan and Shanxi formations have a stable distribution. The coal reservoir of target areas such as Jincheng, Yanquan-Shouyang, Hancheng, Liulin, etc. have good CBM-bearing characteristics, high permeability and appropriate reservoir pressure, and these areas are the preferred target areas of CBM developing in China. The coal reservoirs of Wupu, Sanjiaobei, Lu'an, Xinmi, Anyang-Hebi, Jiaozuo, Xinggong and Huainan also have as good CBM-bearing characteristics, but the physical properties of coal reservoirs vary observably. So, further work should be taken to search for districts with high pressure, high permeability and good CBM-bearing characteristics. Crustal stresses have severe influence on the permeability of coal reservoirs in North China. From west to east, the crustal stress gradient increases, while the coal reservoirs permeability decreases.展开更多
The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The co...The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The corresponding physical properties of 37. 91% CAO-43.09% SiO2-5% Al2O3-5% MgO-2% Li20-7% B2O3 mould fluxes were as follows: the melting point was 909℃, the flowing temperature was 1 160℃, the viscosity and surface tension at 1300 ℃ were 0. 4 Pa · s and 0.32 N/m respectively, which could meet the demands for certain kinds of steels for mould fluxes in continuous casting.展开更多
Sludge,solid waste of sewage treatment plants,poses a threat as a secondary pollution if it is not handled properly.In this study,artifical ceramsite filter material(ACFM)for water treatment,was obtained from sludge b...Sludge,solid waste of sewage treatment plants,poses a threat as a secondary pollution if it is not handled properly.In this study,artifical ceramsite filter material(ACFM)for water treatment,was obtained from sludge by high-temperature sintering process,and then it’s physical properties,leaching toxicity and sintering mechanisms were investigated.The results showed that the preferred conditions for the preparation of ACFM were that the mass ratio of sludge,river sediment and fly ash was 5∶4∶1,preheated at 400℃for 20 min and sintered at 1 150℃for 5 min.After the optimal sintering conditions treatment,the physical properties of the rate of breaking and wear,solubility in hydrochloric acid,silt carrying capacity,void fraction and Brunauer-Emmett-Teller(BET)specific surface area of ACFM were 0.2%,0.01%,0.2%,71.1%and 0.75×104cm2/g,respectively.The results confirmed that the ACFM’s physical properties were totally aligned to the requirements of China’s industry standard(CJ/T 299—2008).The leaching toxicity results indicated that the leaching contents of heavy metals,such as Cr,Zn and Cu,were much lower than the thresholds of China’s national standards(GB 5085.3—2007 and GB 8978—1996).展开更多
The micaceous weathered granitic soil(WGS)is frequently encountered in civil engineering worldwide,unfortunately little information is available regarding how mica affects the physico-mechanical behaviors of WGS.This ...The micaceous weathered granitic soil(WGS)is frequently encountered in civil engineering worldwide,unfortunately little information is available regarding how mica affects the physico-mechanical behaviors of WGS.This study prepares reconstituted WGS with different mica contents by removing natural mica in theWGS,and then mixes it with commercial mica powders.The geotechnical behavior as well as the microstructures of the mixtures are characterized.The addition of mica enables the physical indices of WGS to be specific combinations of coarser gradation and high permeability but high Atterberg limits.However,high mica content in WGS was found to be associated with undesirable mechanical properties,including increased compressibility,disintegration,and swelling potential,as well as poor compactability and low effective frictional angle.Microstructural analysis indicates that the influence of mica on the responses of mixtures originates from the intrinsic nature of mica as well as the particle packing being formed withinWGS.Mica exists in the mixture as stacks of plates that form a spongy structure with high compressibility and swelling potential.Pores among the plates give the soil high water retention and high Atterberg limits.Large pores are also generated by soil particles with bridging packing,which enhances the permeability and water-soil interactions upon immersion.This study provides a microlevel understanding of how mica dominates the behavior of WGS and provides new insights into the effective stabilization and improvement of micaceous soils.展开更多
Different kinds of base oils with different viscosity were analyzed in this paper, including eight mineral base oils, alkylnaphthalene and three synthetic PAO oils. The influence of different hydrocarbon molecules on ...Different kinds of base oils with different viscosity were analyzed in this paper, including eight mineral base oils, alkylnaphthalene and three synthetic PAO oils. The influence of different hydrocarbon molecules on physical properties of mineral base oils was investigated, such as density(d), kinematic viscosity(KV), viscosity index(VI), etc. Possible reasons for some inconsistent phenomena in data processing were also theoretically analyzed in detail. The refractive indexes(RI), d and molecular weight(M) decrease linearly with the increase of paraffinic content other than KV, which declines exponentially. There are no clear relationships between physical properties of base oils and naphthenic content while polycyclic alkanes show a strong correlation with M and KV. The influence of aromatics on physical properties of base oils is just the opposite of paraffin's. VI of the base oils with low aromatics content increases linearly as their paraffinic contents rise when their carbon numbers are approximately equal. However, base oils with high aromatics content follow an utterly different rule, in which VI declines dramatically linearly with the increase in polycyclic aromatic content, which is the essential reason why naphthenic base oils all have terrible viscosity-temperature characteristics while paraffinic base oils usually do not.展开更多
基金State Key Basic Development and Programming Project (G1998040702)the Project (9691307) from Ministry of Science and Technology and China Seismological Bureau.
文摘2-D crustal structure and velocity ratio are obtained by processing S-wave data from two wide-angle reflec-tion/refraction profiles in and around Jiashi in northeastern Pamir, with the result of P-wave data taken into con-sideration. The result shows that: 1) Average crustal velocity ratio is obviously higher in Tarim block than in West Kunlun Mts. and Tianshan fold zone, which reflects its crustal physical property of 'hardness' and stability. The relatively low but normai velocity ratio (Poisson's ratio) of the lower crust indicates that the 'downward thrusting' of Tarim basin is the main feature of crustal movement in this area. 2) The rock layer in the upper crust of Tianshan fold zone is relatively 'soft', which makes it prone to rupture and stress energy release. This is the primary tectonic factor for the concentration of small earthquakes in this area. 3) Jiashi is located right over the apex or the inflection point of the updoming lower crustal interface C and the crust-mantle boundary, which is the deep struc-tural background for the occurrence of strong earthquakes. The alternate variation of vp/vs near the block bounda-ries and the complicated configuration of the interfaces in the upper and middie part of the upper crust form a par-ticular structural environment for the Jiashi strong earthquake swarm. vp/vs is comparatively high and shear modulus is low at the focal region, which may be the main reason for the low stress drop of the Jiashi strong earthquake swarm.
基金Supported by the National Basic Research Program of China under Grant Nos 2015CB921303,2011CBA00100 and 2012CB821404the Strategic Priority Research Program(B) of Chinese Academy of Sciences under Grant Nos XDB07020100and XDB07020200the National Natural Science Foundation of China under Grant No 11174350
文摘We report on the single crystal growth and superconducting properties of PbTaSe2 with the non-centrosymmetric crystal structure. By using the chemicM vapor transport technique, centimeter-size single crystals are success- fully obtained. The measurement of temperature dependence of electricaJ resistivity p(T) in both normal and superconducting states indicates a quasi-two-dimensional electronic state in contrast to that of polycrystalline samples. Specific heat C(T) measurement reveals a bulk superconductivity with Tc ≈ 3.75K and a specific heat jump ratio of 1.42. All these results are in agreement with a moderately electron-phonon coupled, type-g Bardeen-Cooper-Schrieffer superconductor.
文摘From the viewpoints of coexistence theory of the slag structure, the investigation on the structural units of MnO-SiO2 system and the chemical reactions between them has been carried out. The relationships between the physical propenies of the slag and the mass action concentrations of its have been set up at certain temperature and slag composition range, which based on the thermodynamic data of the chemtical reactions between the units and the method of linear regression. The calculated data from the model are in good agreement with the measured results. These calculated values are more accurate and systematic than those from other expirical and semi-expirical formulas used at present.
基金Supported by the National Natural Science Foundation of China Project(31770582)。
文摘Biochar is widely used to improve soil physical properties and carbon sequestration. However, few studies focuse on the impact of maize stalk biochar on labile organic carbon(LOC) pool and the relationship between physical properties and LOC fractions. A field positioning experiment was performed in Mollisols region of Northeast China to evaluate the influence of maize stalk biochar on the spatial distribution and temporal changes of physical properties and LOC fractions. Maize stalk biochar treatments included C1(1.5 kg·hm^(-2)), C2(3 kg·hm^(-2)), C3(15 kg·hm^(-2)), C4(30 kg·hm^(-2)), and CK(0). The results showed that maize stalk biochar increased soil water contents(SWC) and soil porosity(SP), but reduced bulk density(BD). Maize stalk biochar reduced dissolved organic carbon(DOC) contents in the 0-20 cm soil layer, ranging from 0.25 g·kg^(-1) to 0.31 g·kg^(-1) in harvest period, while increased in the 20-40 cm soil layer. In addition, the application of biochar had a significant impact on the spatial distribution and temporal change of SWC, BD, SP, DOC, hot-water extractable carbon(HWC), acid hydrolyzed organic carbon(AHC Ⅰ, Ⅱ), and readily oxidized organic carbon(ROC). High amounts of maize stalk biochar up-regulated the contents of soil organic carbon SOC, HWC, AHC Ⅰ, AHC Ⅱ, and ROC. In addition, SWC and SP were the key physical factors to affect LOC fractions. In conclusions, maize stalk biochar could improve physical properties, and then influence LOC fractions, and maize stalk biochar could be used as an organic amendment for restoring degraded soils governed by their rates of addition.
基金Natural Science Foundation of Jiangsu Province,Grant/Award Number:BK20210527National Natural Science Foundation of China,Grant/Award Number:42107158Training Program for Innovation and Entrepreneurship,China University of Mining and Technology。
文摘In recent years,the exploration of seabed has been intensified,but the submarine soils of silt and sand in the Yellow Sea area have not been well investigated so far.In this study,the physical and mechanical properties of silt and sand from the Yellow Sea were measured using a direct shear apparatus and their microstructures were observed using a scanning electron microscope.The test results suggest that the shear strength of silt and sand increases linearly with the increase of normal stress.Based on the direct shear test,the scanning electron microscope was used to observe the section surface of sand.It is observed that the section surface becomes rough,with many“V”‐shaped cracks.Many particles appear on the surface of the silt structure and tend to be disintegrated.The X‐ray diffraction experiment reveals that the sand and silt have different compositions.The shear strength of sand is slightly greater than that of silt under high stress,which is related to the shape of soil particles and the mineral composition.These results can be a reference for further study of other soils in the Yellow Sea;meanwhile,they can serve as soil parameters for the stability and durability analyses of offshore infrastructure construction.
文摘Salvaged cow horns from slaughterhouses have been transformed into fine particles for a physical characterization that has led us to determine the humidity rate (2.34% ± 0.054%), the actual density situated between 0.586 g/cm<sup>3</sup> and 0.732 g/cm<sup>3</sup>, the swelling rate (12%), and one chemical characterization that permitted us to determine the rate of dry matters (97.05%), of mineral matters (2.5%), of protein matters (94.52%). From these weak values, it can easily be seen that cow horn case doesn’t absorb much water and improve the mechanical characteristics of the composite;the high rate of protein shows that keratin which is the structural molecule favors its gripping as reinforcing element in the manufacturing of composite materials.
文摘Changqing old oilfield Jurassic reservoir's average calibration recovery is 24.7%,with geological reserves recovery of 16.6%,water cut of 65.2%.And most of Jurassic reservoirs are in the middle and later field life,part of them has entered the high water cut and high recovery stage.Traditional water flooding way for improving oil recovery becomes more difficult,and new method has to be considered.Maling oilfield BS district is a typical representative,with high water cut of 90.8%,high recovery percent of 26.1%and low oil recovery rate of 0.25%.To explore the new way to improve oil recovery,the polymer and surfactant(SP for short)important pilot test has been developed.The low permeability reservoir indoor core data in high water cut stage and inspection well results indicate that the reservoir permeability,pore combination characteristics and pore type changed greatly after long-term water flooding development.These changes bring more difficulties to the continue development,especially the high injection pressure,which can cause other problems for well pattern infilling and EOR.This paper takes the high injection pressure problem of Maling BS district Jurassic reservoir for example,analyzes the physical property change law on the following aspects:the development mode in the past,core analysis,formation sensitivity,interstitial matter,well test interpretation results,in order to help to further effective development and provide important parameters for tertiary oil recovery technique for similar reservoirs and others.
基金supported by the National Natural Science Foundation of China (21878318, 22108285)the DNL Cooperation Fund, CAS (DNL201902)+2 种基金“Transformational Technologies for Clean Energy and Demonstration”, Strategic Priority Research Program of the Chinese Academy of Sciences (CAS) (XDA21060400)Shandong Energy Institute, Single-Cell Center Project (SCZ-16, SCZ17)Director Innovation Fund of Synthetic Biology Technology Innovation Center of Shandong Province (sdsynbio-2020-ZH-02)。
文摘Solid physical properties are vital for the design, optimization, and scale-up of gas–liquid–solid multiphase reactors. The complex and interactional effects of the solid physical properties, including particle diameter, density, wettability, and sphericity, on the hydrodynamic behaviors in a new external airlift loop reactor(EALR) integrating mixing and separation are decoupled in this work. Two semi-empirical equations are proposed and validated to predict the overall gas holdup and liquid circulating velocity satisfactorily, and then the individual influence of such solid physical properties is further investigated. The results demonstrate that both the overall gas holdup in the riser and the liquid circulating velocity in the downcomer increase with the contact angle, but decrease with particle size, density, and sphericity.Additionally, the impact of the particle size on the liquid circulating velocity is also profoundly revealed on a micro-level considering the particle size distribution. Moreover, the axial solid concentration distribution is discussed, and the uniformity of the slurry is described by the mixing index of the solid particles. The results show that a more homogeneous mixture can be achieved by adding finer particles other than attaining violent turbulence. Therefore, this work lays a foundation for the design, scale-up, and industrialization of the EALRs.
基金the Iranian National Science Foundation(INSF)for the financial support of this research under Project Number 4004169Isfahan University of Technology。
文摘Knowledge about the spatial distribution of the soil physical and mechanical properties is crucial for soil management,water yield,and sustainability at the watershed scale;however,the lack of soil data hinders the application of this tool,thus urging the need to estimate soil properties and consequently,to perform the spatial distribution.This research attempted to examine the proficiency of three machine learning methods(RF:Random Forest;Cubist:Regression Tree;and SVM:Support Vector Machine)to predict soil physical and mechanical properties,saturated hydraulic conductivity(Ks),Cohesion measured by fall-cone at the saturated(Psat)and dry(Pdry)states,hardness index(HI)and dry shear strength(SS)by integrating environmental variables and soil features in the Zayandeh-Rood dam watershed,central Iran.To determine the best combination of input variables,three scenarios were examined as follows:scenarioⅠ,terrain attributes derivative from a digital elevation model(DEM)+remotely sensed data;scenarioⅡ,covariates of scenarioⅠ+selected climatic data and some thematic maps;scenarioⅢ,covariates in scenarioⅡ+intrinsic soil properties(Clay,Silt,Sand,bulk density(BD),soil organic matter(SOM),calcium carbonate equivalent(CCE),mean weight diameter(MWD)and geometric weight diameter(GWD)).The results showed that for Ks,Psat Pdry and SS,the best performance was found by the RF model in the third scenario,with R2=0.53,0.32,0.31 and 0.41,respectively,while for soil hardness index(HI),Cubist model in the third scenario with R2=0.25 showed the highest performance.For predicting Ks and Psat,soil characteristics(i.e.clay and soil SOM and BD),and land use were the most important variables.For predicting Pdry,HI,and SS,some topographical characteristics(Valley depth,catchment area,mltiresolution of ridge top flatness index),and some soil characteristics(i.e.clay,SOM and MWD)were the most important input variables.The results of this research present moderate accuracy,however,the methodology employed provides quick and costeffective information serving as the scientific basis for decision-making goals.
基金Supported by the China National Natural Science Foundation(41872140)Taishan Scholars and Young Experts Project(201909061)+1 种基金Qingdao Marine Science and Technology Pilot Special Fund for National Laboratory in Shandong Province(2021QNLM020001)Central University Innovation Fund(20CX06067A).
文摘The element geochemical characteristics and diagenetic alteration products of tuffaceous components in sandstone reservoirs of Paleogene Wenchang Formation in typical subsags of the Huizhou-Lufeng area of the Zhu I Depression,Pearl River Mouth Basin,were identified through microscopic analysis and quantitative analysis of main and trace elements.The impacts of dissolution of different tuffaceous components on physical properties of reservoirs were discussed through quantitative characterization of reservoir physical properties.The results show that there are mainly four types of tuffaceous components in the study area,which are acidic,intermediate,basic and alkaline tuffaceous components.The acidic tuffaceous components evolved in a process of strong alteration and weak dissolution of alteration products,with a large amount of kaolinite precipitated during alteration to disenable the improvement of porosity and permeability.The intermediate and alkaline tuffaceous components evolved in a process of strong dissolution of tuffaceous components and strong alteration of residual tuffaceous components;the dissolution of tuffaceous components created intergranular pores,but the alteration products such as autogenic quartz,apatite and illite deteriorated the pore structure;ultimately,the dissolution of tuffaceous components resulted in the increase of porosity but no increase of permeability of the reservoir.The basic tuffaceous components dominantly evolved in a process of dissolution of tuffaceous components to strong dissolution of alteration products;both tuffaceous components between particles and laumontite generated from alteration can be strongly dissolved to create pores;thus,the dissolution of tuffaceous components can significantly increase the physical properties of the reservoir.
基金supported by the National Natural Science Foundation of China(Nos.U2013603 and 52225403)the Program for Guangdong Introducing Innovative and Entrepreneurial Teams(No.2019ZT08G315)the Shenzhen National Science Fund for Distinguished Young Scholars(No.RCJC20210706091948015).
文摘With the increasing scarcity of Earth’s resources and the development of space science and technology,the exploration, development, and utilization of deep space-specific material resources(minerals, water ice, volatile compounds, etc.) are not only important to supplement the resources and reserves on Earth but also provide a material foundation for establishing extraterrestrial research bases. To achieve large depth in-situ condition-preserved coring(ICP-Coring) in the extreme lunar environment, first, lunar rock simulant was selected(SZU-1), which has a material composition, element distribution, and physical and mechanical properties that are approximately equivalent to those of lunar mare basalt. Second, the influence of the lunar-based in-situ environment on the phase, microstructure, and thermal physical properties(specific heat capacity, thermal conductivity, thermal diffusivity, and thermal expansion coefficient)of SZU-1 was explored and compared with the measured lunar rock data. It was found that in an air atmosphere, low temperature has a more pronounced effect on the relative content of olivine than other temperatures, while in a vacuum atmosphere, the relative contents of olivine and anorthite are significantly affected only at temperatures of approximately-20 and 200 ℃. When the vacuum level is less than100 Pa, the contribution of air conduction can be almost neglected, whereas it becomes dominant above this threshold. Additionally, as the testing temperature increases, the surface of SZU-1 exhibits increased microcracking, fracture opening, and unevenness, while the specific heat capacity, thermal conductivity,and thermal expansion coefficient show nonlinear increases. Conversely, the thermal diffusivity exhibits a nonlinear decreasing trend. The relationship between thermal conductivity, thermal diffusivity, and temperature can be effectively described by an exponential function(R^(2)>0.98). The research results are consistent with previous studies on real lunar rocks. These research findings are expected to be applied in the development of the test and analysis systems of ICP-Coring in a lunar environment and the exploration of the mechanism of machine-rock interaction in the in-situ drilling and coring process.
基金financially supported by grants from the Key Scientific Research Projects of Hubei Province(2020BCA086)the National Key Research and Development Program of China(2017YFD0400200)+3 种基金Wuhan Application Fundamental Frontier Project of China(2020020601012270)the National Natural Science Foundation of China(31771938)the China Agriculture Research System of MOF and MARAthe Wuhan Achievement Transformation Project(2019030703011505)。
文摘This study characterized and compared the physical and emulsifying properties of pea protein(PP)and its modified proteins(ultrasound treated-PP(PPU),flaxseed gum(FG)treated PP(PPFG)and ultrasound treated-PPFG(PPFGU)).The results showed FG triggered the formation of loosely attached complex with PP via physical modification under gentle magnetic stirring at pH 7.0,while ultrasound played an important role in reducing protein size,increasing surface hydrophobicity and molecular fluidity onto oil-water interface.So ultrasound further enhanced the interaction of PP with FG,and produced the PPFGU complex with smaller droplet size,higherζ-potential and lower turbidity.Further,combination of FG and ultrasound improved the physical properties of PP with higher viscosity,stiffer gels(defined as higher elastic modulus),stronger hydrophobic properties,better thermal stability,and fast protein absorption rate.Therefore,the PPFGU coarse emulsion performed highest emulsifying activity index(EAI)and emulsion stability index(ESI)that the stabilized nanoemulsion obtained smallest droplet size,higherζ-potential,and longest storage stability.The combination of FG and ultrasonic treatment will be an effective approach to improving the emulsifying property and thermal stability of PP,which can be considered as a potential plant-based emulsifier applied in the food industry.
基金supported by the Shandong Province Natural Science Foundation of China(Grant no.ZR2021MD077)the National Major Science and Technology Project of China(Grant no.2017ZX05001-001-006).
文摘Cements are widely developed in clastic rock-originated weathering crust(CWC)reservoirs in the Kexia region along the northwestern margin of the Junggar Basin and significantly affect reservoir physical properties and oil and gas distribution in this area.Focusing on the CWC reservoirs at the top of both the Permian Jiamuhe Formation and the Triassic Karamay Formation,this study analyzed the types and characteristics of cements in the reservoirs and explored their effects on reservoir physical properties based on thin sections,SEM images,XRD results,and tests of physical properties.The main results are as follows.The cements in the CWC reservoirs in Kexia region mainly consist of carbonate minerals(41.5%),clay minerals(27.8%)and zeolite minerals(30%),as well as small amount of siliceous minerals.Among them,the carbonate minerals are dominated by siderite and calcite,the clay minerals mainly include kaolinite,interstratified illite/smectite(I/S)and chlorite,and the zeolite minerals primarily comprise heulandite and laumontite.These different types of multiphase cements are generally paragenetic or associated and affect reservoir physical properties to different degrees.Specifically,the carbonate and clay cements of the early diagenetic stage reduced the reservoirs’average porosity from 21%to 15%.The dissolution of some carbonate and zeolite cements in the early A substage of the middle diagenetic stage restored the average porosity to 18%,and the cementation in the late A substage decreased the average porosity to 13%again,of which about 4%was reduced by carbonate cements.The average porosity of the CWC reservoirs gradually decreased to the current value of approximately 10%in the B substage of the middle diagenetic stage.The impact of cementation on the CWC reservoirs can reach as far as 70 m below the unconformity.Moreover,the types and contents of cements vary with their depth below the unconformity surface,leading to the development of multiple zones with high cement content and the differentiated oil and gas distribution.
文摘The accurate assessment of soil properties is a crucial factor for composing and implementing reclamation plans. The main objective of this study was to evaluate soil chemical and physical properties and calculate the chemical and fertility index for assisting land reclamation in Toshka area. The Toshka area is located between latitudes 31°32'N and 31°36'N and longitudes 32°40'E and 32°60'E. GIS was used to select 16 sites. The results revealed the soil has undesirable characteristics. The soil pH ranged from slightly alkaline to moderately alkaline. Furthermore, it was characterized as saline (with a ECe of 4.65 - 11.45 dS⋅m<sup>−1</sup>) and moderately calcareous soil (with CaCO<sub>3</sub> at 11.85% - 17.20%). The soil had a low soil organic matter content which did not exceed 0.18%. The soil was dominated by a sandy loam texture (62.50%) followed by a sandy clay loam texture (18.75%). The bulk density, total soil porosity and saturated hydraulic conductivity values varied with 1.38 - 1.55 Mg⋅cm<sup>−3</sup>, 41.85% - 48.45% and 1.20 - 3.34 cm⋅h<sup>−1</sup>, respectively. The chemical index ranged from low to moderate quality. The correlations between the parameters osculated between negative and positive. Therefore, the soil may be reclaimed if the soil properties are improved and crop selection is optimized for this soil.
基金supported by Special Fund for Agro-scientific Research in the Public Interest(201103005)Ministry of Agriculture,China and the International Plant Nutrition Institute(IPNI,Hunan-14)
文摘Soil physical properties are important indicators of the potential for agricultural production.Our objective was to evaluate the effects of long-term inputs of green manures on physical properties of a reddish paddy soil(Fe-Typic Hapli-Stagnic Anthrosols) under a double cropping system.The common cropping pattern before the study was early-late rice-fallow(winter).The field treatments included rice-rice-fallow(R-R-WF),rice-rice-rape(R-R-RP),rice-rice-Chinese milk vetch(RR-MV),and rice-rice-ryegrass(R-R-RG).The rape,Chinese milk vetch and ryegrass were all incorporated as green manures 15 d before early rice transplanting during the following year.The soil bulk density in all green manure treatments was significantly reduced compared with the winter fallow treatment.Soil porosity with green manure applications was significantly higher than that under the winter fallow.The green manure treatments had higher 0.25-5 mm water stable aggregates and aggregates stabilities in the plow layer(0-15 cm depth) compared with the fallow treatment.The mean weight diameter(MWD) and normalized mean weight diameter(NMWD) of aggregates in the green manure treatment were larger than that with the winter fallow.Soil given green manure retained both a higher water holding capacity in the plow layer soil,and a larger volume of moisture at all matric potentials(-10,-33 and-100 kPa).We conclude that the management of double-rice fields in southern central China should be encouraged to use green manures along with chemical fertilizers to increase SOC content,improve soil physical properties and soil fertility.
基金These research results are a part of the National Key Foundation Research Development an d Plan ning Program of China(No.2002CB2ll702)National Natural Science Foundation of China(No.40272069)
文摘The coalbed methane (CBM) resources in North China amounts up to 60% of total resources in China. North China is the most important CBM accumulation area in China. The coal beds of the Upper Paleozoic Taiyuan and Shanxi formations have a stable distribution. The coal reservoir of target areas such as Jincheng, Yanquan-Shouyang, Hancheng, Liulin, etc. have good CBM-bearing characteristics, high permeability and appropriate reservoir pressure, and these areas are the preferred target areas of CBM developing in China. The coal reservoirs of Wupu, Sanjiaobei, Lu'an, Xinmi, Anyang-Hebi, Jiaozuo, Xinggong and Huainan also have as good CBM-bearing characteristics, but the physical properties of coal reservoirs vary observably. So, further work should be taken to search for districts with high pressure, high permeability and good CBM-bearing characteristics. Crustal stresses have severe influence on the permeability of coal reservoirs in North China. From west to east, the crustal stress gradient increases, while the coal reservoirs permeability decreases.
基金Item Sponsored by National Natural Science Foundation of China (50474037) Jiangsu Province Natural Science Foundation forUniversity of China (04BJK430022)
文摘The flux agents in common mould fluxes were fluoride and sodium oxide, which would do great harm to environments. B2O3 was selected as flux. The physical properties of B2O3-containing mould fluxes were studied. The corresponding physical properties of 37. 91% CAO-43.09% SiO2-5% Al2O3-5% MgO-2% Li20-7% B2O3 mould fluxes were as follows: the melting point was 909℃, the flowing temperature was 1 160℃, the viscosity and surface tension at 1300 ℃ were 0. 4 Pa · s and 0.32 N/m respectively, which could meet the demands for certain kinds of steels for mould fluxes in continuous casting.
基金Specialized Research Fund for the Doctoral Program of Higher Education of China(No.20130075110006)Education Innovation Project of Shanghai,China(No.12ZZ069)Natural Science Foundation of Shanghai,China(No.11ZR1400400)
文摘Sludge,solid waste of sewage treatment plants,poses a threat as a secondary pollution if it is not handled properly.In this study,artifical ceramsite filter material(ACFM)for water treatment,was obtained from sludge by high-temperature sintering process,and then it’s physical properties,leaching toxicity and sintering mechanisms were investigated.The results showed that the preferred conditions for the preparation of ACFM were that the mass ratio of sludge,river sediment and fly ash was 5∶4∶1,preheated at 400℃for 20 min and sintered at 1 150℃for 5 min.After the optimal sintering conditions treatment,the physical properties of the rate of breaking and wear,solubility in hydrochloric acid,silt carrying capacity,void fraction and Brunauer-Emmett-Teller(BET)specific surface area of ACFM were 0.2%,0.01%,0.2%,71.1%and 0.75×104cm2/g,respectively.The results confirmed that the ACFM’s physical properties were totally aligned to the requirements of China’s industry standard(CJ/T 299—2008).The leaching toxicity results indicated that the leaching contents of heavy metals,such as Cr,Zn and Cu,were much lower than the thresholds of China’s national standards(GB 5085.3—2007 and GB 8978—1996).
基金The financial supports of the National Natural Science Foundation of China(Grant No.42177148)the opening fund of State Key Laboratory of Geohazard Prevention and Geo-environment Protection(Grant No.SKLGP 2023K011)Postdoctoral Research Project of Guangzhou(Grant No.20220402)are gratefully thanked.
文摘The micaceous weathered granitic soil(WGS)is frequently encountered in civil engineering worldwide,unfortunately little information is available regarding how mica affects the physico-mechanical behaviors of WGS.This study prepares reconstituted WGS with different mica contents by removing natural mica in theWGS,and then mixes it with commercial mica powders.The geotechnical behavior as well as the microstructures of the mixtures are characterized.The addition of mica enables the physical indices of WGS to be specific combinations of coarser gradation and high permeability but high Atterberg limits.However,high mica content in WGS was found to be associated with undesirable mechanical properties,including increased compressibility,disintegration,and swelling potential,as well as poor compactability and low effective frictional angle.Microstructural analysis indicates that the influence of mica on the responses of mixtures originates from the intrinsic nature of mica as well as the particle packing being formed withinWGS.Mica exists in the mixture as stacks of plates that form a spongy structure with high compressibility and swelling potential.Pores among the plates give the soil high water retention and high Atterberg limits.Large pores are also generated by soil particles with bridging packing,which enhances the permeability and water-soil interactions upon immersion.This study provides a microlevel understanding of how mica dominates the behavior of WGS and provides new insights into the effective stabilization and improvement of micaceous soils.
文摘Different kinds of base oils with different viscosity were analyzed in this paper, including eight mineral base oils, alkylnaphthalene and three synthetic PAO oils. The influence of different hydrocarbon molecules on physical properties of mineral base oils was investigated, such as density(d), kinematic viscosity(KV), viscosity index(VI), etc. Possible reasons for some inconsistent phenomena in data processing were also theoretically analyzed in detail. The refractive indexes(RI), d and molecular weight(M) decrease linearly with the increase of paraffinic content other than KV, which declines exponentially. There are no clear relationships between physical properties of base oils and naphthenic content while polycyclic alkanes show a strong correlation with M and KV. The influence of aromatics on physical properties of base oils is just the opposite of paraffin's. VI of the base oils with low aromatics content increases linearly as their paraffinic contents rise when their carbon numbers are approximately equal. However, base oils with high aromatics content follow an utterly different rule, in which VI declines dramatically linearly with the increase in polycyclic aromatic content, which is the essential reason why naphthenic base oils all have terrible viscosity-temperature characteristics while paraffinic base oils usually do not.