Genetic Analysis of Structural Styles in the Makran Accretionary Wedge–Insight from Physical Simulations

The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the formation mechanism of shallow normal faults, remain unclear. Meanwhile, the factors affecting the continuity of plane faults must be comprehensively discussed. Clarifying the development characteristics and deformation mechanisms of the Makran accretionary wedge is crucial to effectively guide the exploration of gas hydrate deposits in the area. This study aims to interpret seismic data to identify typical structures in the Makran accretionary wedge, including deep imbricate thrust faults, shallow and small normal faults, wedge-shaped piggyback basins, mud diapirs with fuzzy and disorderly characteristics of reflection, décollements with a northward tilt of 1° – 2°, and large seamounts. Physical simulation-based experiments are performed to comprehensively analyze the results of the plane, section, and slices of the wedge. Results reveal that the distances between and shapes of thrust faults in the deep parts of the Makran accretionary wedge are controlled by the bottom décollement. The uplift of the thrust fault-related folds and the upwelling of the mud diapirs primarily contribute to the formation of small normal faults in the shallow part of the area. The mud diapirs originate from plastic material at the bottom, while those that have developed in the area near the trench are larger. Seamounts and mud diapirs break the continuity of fault plane distribution.

Numerical and physical simulations of array laterolog in deviated anisotropic formation

Due to the tremendous amount of high-resolution measurement information,array laterolog is widely used in evaluations of deviated anisotropic reservoirs.However,the precision of a complementary numerical simulation should be improved as high as the core of fine-scale reservoir evaluation.Therefore,the 3D finite element method(3D-FEM)is presented to simulate the array laterolog responses.Notably,a downscaled physical simulation system is introduced to validate and calibrate the precision of the 3D-FEM.First,the size of the downscaled system is determined by COMSOL.Then,the surrounding and investigated beds are represented by a sodium chloride solution and planks soaked in solution,respectively.Finally,a half-space measurement scheme is presented to improve the experimental efficiency.Moreover,the corresponding sensitivity function and separation factor are established to analyze the effects of the formation anisotro py and dipping angle on the array laterolog responses.The numerical and experimental results indicate that the half-space method is practical,and the mean relative error between the numerical and experimental results is less than 5%,which indicates that the numerical simulation is accurate.With the proposed approach,the reversal angle of array laterolog response curves in anisotropic formations can be observed,and this range is determined to be 50°-62°.

Mechanical behaviors of backfill-rock composites: Physical shear test and back-analysis

The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.

An online physical simulation method for enhanced oil recovery by air injection in shale oil

In order to understand the mechanism of air flooding shale oil, an online physical simulation method for enhanced shale oil recovery by air injection was established by integrating CT scanning and nuclear magnetic resonance(NMR). The development effect of shale oil by air flooding under different depletion pressures, the micro-production characteristics of pore throats with different sizes and the mechanism of shale oil recovery by air flooding were analyzed. The effects of air oxygen content, permeability, gas injection pressure, and fractures on the air flooding effect in shale and crude oil production in pores with different sizes were analyzed. The recovery of shale oil can be greatly improved by injecting air into the depleted shale reservoir, but the oil displacement efficiency and the production degree of different levels of pore throats vary with the injection timing. The higher the air oxygen content and the stronger the low-temperature oxidation, the higher the production degree of pores with different sizes and the higher the shale oil recovery. The higher the permeability and the better the pore throat connectivity, the stronger the fluid flow capacity and the higher the shale oil recovery. As the injection pressure increases, the lower limit of the production degree of pore throats decreases, but gas channeling may occur to cause a premature breakthrough;as a result, the recovery increases and then decreases. Fractures can effectively increase the contact area between gas and crude oil, and increase the air sweep coefficient and matrix oil drainage area by supplying oil to fractures through the matrix, which means that a proper fracturing before air injection can help to improve the oil displacement effect under a reasonable production pressure difference.

Melting and floating processes of inorganic materials in molten steel:Visualization physical simulation and mathematical modelling

It has been demonstrated that heat absorption method by using the inorganic material rod to cool the molten steel can significantly reduce the macrosegregation level of the large steel ingot.However,owing to the opacity of the molten steel,the physical mechanism of the heat absorption method is not clear.In this work,a transparent hydraulic physical model with water and paraffin wax was built to simulate the melting and floating processes of inorganic materials in the molten steel.A mathematical simulation was also carried out to analyze the connection between the actual ingot and the physical model.Results show that it is feasible to simulate the molten steel and inorganic materials with water and paraffin wax.With the help of the physical model,the process of the melting of paraffin wax and its floating to the surface of water were clearly observed,during which the temperature of water at some characteristic positions in the mold was recorded.The visualization findings demonstrate that the melting and floating processes of paraffin wax can help to bring the heat from the center of the mold to the top surface more quickly,which reduces the superheat and significantly accelerates the cooling rate of water.The experimental results show that for the water with a certain superheat,the use of a larger mass of paraffin wax can accelerate the cooling of the water,but there is a risk of incomplete melting of the paraffin wax.A higher superheat of water will lead to a quicker melting rate for a given mass of paraffin wax,while a lower superheat leads to the incomplete melting of paraffin wax as well.

Action mechanisms of abnormal fluid pressure on physical properties of deep reservoirs: A case study on Jurassic Toutunhe Formation in the southern margin of Junggar Basin, NW China

Considering the action mechanisms of overpressure on physical changes in skeleton particles of deep reservoir rocks and the differences in physical changes of skeleton particles under overpressure and hydrostatic pressure, the sandstone of the Jurassic Toutunhe Formation in the southern margin of Junggar Basin was taken as an example for physical modeling experiment to analyze the action mechanisms of overpressure on the physical properties of deep reservoirs. (1) In the simulated ultra-deep layer with a burial depth of 6000-8000 m, the mechanical compaction under overpressure reduces the remaining primary pores by about a half that under hydrostatic pressure. Overpressure can effectively suppress the mechanical compaction to allow the preservation of intergranular primary pores. (2) The linear contact length ratio under overpressure is always smaller than the linear contact length ratio under hydrostatic pressure at the same depth. In deep reservoirs, the difference between the mechanical compaction degree under overpressure and hydrostatic pressure shows a decreasing trend, the effect of abnormally high pressure to resist the increase of effective stress is weakened, and the degree of mechanical compaction is gradually close to that under hydrostatic pressure. (3) The microfractures in skeleton particles of deep reservoirs under overpressure are thin and long, while the microfractures in skeleton particles of deep reservoirs under hydrostatic pressure are short and wide. This difference is attributed to the probable presence of tension fractures in the rocks containing abnormally high pressure fluid. (4) The microfractures in skeleton particles under overpressure were mainly formed later than that under hydrostatic pressure, and the development degree and length of microfractures both extend deeper. (5) The development stages of microfractures under overpressure are mainly controlled by the development stages of abnormally high pressure and the magnitude of effective stress acting on the skeleton particles. Moreover, the development stages of microfractures in skeleton particles are more than those under hydrostatic pressure in deep reservoir. The multi-stage abnormally high pressure plays an important role in improving the physical properties of deep reservoirs.

Numerical simulation and physical analysis for dynamic behaviors of P/M TiAl alloy in hot-packed forging process

The hot forging of large-scale P/M TiAl alloy billet deformation was investigated based on a joint application of Deform-3D-based numerical simulation and physical simulation techniques.The temperature dependence on the thermal and mechanical properties of the billet was considered and the optimum hot working temperature of packed TiAl alloy was 1150-1200 °C.Based on the simulation,the material flow and thermo mechanical field variables,such as stress,strain,and temperature distribution were obtained and the relationships of load—displacement and load—time were figured out.To verify the validity of the simulation results,the experiments were also carried out in a forging plant,and a pancake with diameter of 150 mm was obtained exhibiting a regular shape.

Study of deep transportation and plugging performance of deformable gel particles in porous media

Deformable gel particles(DGPs) possess the capability of deep profile control and flooding. However, the deep migration behavior and plugging mechanism along their path remain unclear. Breakage, an inevitable phenomenon during particle migration, significantly impacts the deep plugging effect. Due to the complexity of the process, few studies have been conducted on this subject. In this paper, we conducted DGP flow experiments using a physical model of a multi-point sandpack under various injection rates and particle sizes. Particle size and concentration tests were performed at each measurement point to investigate the transportation behavior of particles in the deep part of the reservoir. The residual resistance coefficient and concentration changes along the porous media were combined to analyze the plugging performance of DGPs. Furthermore, the particle breakage along their path was revealed by analyzing the changes in particle size along the way. A mathematical model of breakage and concentration changes along the path was established. The results showed that the passage after breakage is a significant migration behavior of particles in porous media. The particles were reduced to less than half of their initial size at the front of the porous media. Breakage is an essential reason for the continuous decreases in particle concentration, size, and residual resistance coefficient. However, the particles can remain in porous media after breakage and play a significant role in deep plugging. Higher injection rates or larger particle sizes resulted in faster breakage along the injection direction, higher degrees of breakage, and faster decreases in residual resistance coefficient along the path. These conditions also led to a weaker deep plugging ability. Smaller particles were more evenly retained along the path, but more particles flowed out of the porous media, resulting in a poor deep plugging effect. The particle size is a function of particle size before injection, transport distance, and different injection parameters(injection rate or the diameter ratio of DGP to throat). Likewise, the particle concentration is a function of initial concentration, transport distance, and different injection parameters. These models can be utilized to optimize particle injection parameters, thereby achieving the goal of fine-tuning oil displacement.

Formation mechanism of fault accommodation zones under combined stress in graben basin:Implications from geomechanical modeling

A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,indicating the potential exploration target and petroleum accumulation areas.This study aims to analyze the formation mechanism and development of fault accommodation zones under combined stress by a numerical simulation method considering geomechanical modeling.Using three-dimensional(3-D)seismic interpretation and fractal dimension method,exampled with the Dongxin fault zone,the fault activity and fault combination pattern were conducted to quantitatively characterize the activity difference in fault accommodation zones.Combined with mechanical experiment test,a geomehcanical model was established for fault accommodation zones in a graben basin.Integrating the paleostress numerical simulations and structural physical simulation experiment,the developmental characteristics and genetic mechanism of fault accommodation zones were summarized.Influenced by multi movements and combined stresses,three significant tectonic evolution stages of the Dongxing Fault Zone(DXFZ)were distinguished:During the E_(s)^(3)sedimentary period,the large difference in the stress,strain,and rupture distribution in various faults were significant,and this stage was the key generation period for the prototype of the DXFZ,including the FAZ between large-scale faults.During the E_(s)^(2)sedimentary period,the EW-trending symmetric with opposite dipping normal faults and the NE-SW trending faults with large scale were furtherly developed.The junction area of two secondary normal faults were prone to be ruptured,performing significant period for inheriting and developing characteristics of fault accommodation zones.During the Es1 sedimentary period,the high-order faults in the DXFZ exhibited the obvious fault depressions and strike-slip activity,and the fault accommodation zones were furtherly inherited and developed.This stage was the molded and formative period of the FAZ,the low-order faults,and the depression in the DXFZ.

Experiment of dynamic seepage of tight/shale oil under matrix fracture coupling

A physical simulation method with a combination of dynamic displacement and imbibition was established by integrating nuclear magnetic resonance(NMR)and CT scanning.The microscopic production mechanism of tight/shale oil in pore throat by dynamic imbibition and the influencing factors on the development effect of dynamic imbibition were analyzed.The dynamic seepage process of fracking-soaking-backflow-production integration was simulated,which reveals the dynamic production characteristics at different development stages and their contribution to enhancing oil recovery(EOR).The seepage of tight/shale reservoirs can be divided into three stages:strong displacement and weak imbibition as oil produced rapidly by displacement from macropores and fractures,weak displacement and strong imbibition as oil produced slowly by reverse imbibition from small pores,and weak displacement and weak imbibition at dynamic equilibrium.The greater displacement pressure results in the higher displacement recovery and the lower imbibition recovery.However,if the displacement pressure is too high,the injected water is easy to break through the front and reduce the recovery degree.The higher the permeability,the greater the imbibition and displacement recovery,the shorter the time of imbibition balance,and the higher the final recovery.The fractures can effectively increase the imbibition contact area between matrix and water,reduce the oil-water seepage resistance,promote the oil-water displacement between matrix and fracture,and improve the oil displacement rate and recovery of the matrix.The soaking after fracturing is beneficial to the imbibition replacement and energy storage of the fluid;also,the effective use of the carrying of the backflow fluid and the displacement in the mining stage is the key to enhancing oil recovery.

Discussion on the application prospect of the transient electromagnetic method based on the dual launcher and mine advanced detection

The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.

Production of Artificial Fog in the PAVIN Fog and Rain Platform: In Search of Big Droplets Fog

In fog, visibility is reduced. This reduction in visibility is measured by the meteorological optical range (MOR), which is important for studying human perception and various sensors in foggy conditions. The Cerema PAVIN Fog & Rain platform is capable of producing calibrated fog in order to better analyses it and understand its consequences. The problem is that the droplets produced by the platform are not large enough to resemble real fog. This can have a major impact on measurements since the interaction between electromagnetic waves and fog depends on the wavelength and diameter of the droplets. To remedy this, Cerema is building a new platform with new equipment capable of generating fog. This study analyses different nozzles and associated usage parameters such as the type of water used and the pressure used. The aim is to select the best nozzle with the associated parameters for producing large-diameter droplets and therefore more realistic fog.

Similarity criteria and coal-like material in coal and gas outburst physical simulation

Coal and gas outburst is one of the main gas hazards in coal mines. However, due to the risks of the coal and gas outburst, the field test is difficult to complete. Therefore, an effective approach to studying the mechanism and development of outburst is to conduct the similar physical simulation. However, the similarity criteria and similar materials in outburst are the key factors which restrict the development of physical simulation. To solve those problems, this paper has established similarity criteria base on mechanics model, solid-fluid coupling model and energy model, and presented high similar materials. Combining with three groups of similar number, and considering similar mechanical parameters and deformation and failure regularity, the similarity criteria of outburst is determined on the basis of the energy model. According to those criteria, we put forward a similar material consists of pulverized coal, cement, sand, activated carbon, and water. The similar material has high compressive strength and the accordant characteristics with the raw coal, include density, porosity, adsorption, desorption. The new research is promising for preventing and controlling gas hazards in the future.

Physical Simulation and Experimental Examination of ε-Cu Particles Dissolution Evolution During Welding of Copper Precipitation Strengthening Steel

The kinetics of ε-Cu particles dissolution in the matrix during welding of a copper-precipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness meas urement. The ε-Cu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000℃, which resulted in the decrease in the number density of ε-Cu particles and hardness in the heat affected zone （HAZ）. The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.

Physical Simulation of Mold-Filling Processing of Thin-Walled Castings under Traveling Magnetic Field

Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physical simulation method using gallium melt and fast speed photography. Flow morphology and its formation mechanism were obtained and discussed for thin-walled casting. The influences of magnetic field density on the filling ability, filling velocity and mold filling time have been studied. The differences in filling capability between gravity casting and casting under the traveling magnetic field have been compared. The results indicate that the mold filling ability of the gallium melt increases greatly under the condition of traveling magnetic field; the filling time is shortened from 18 s under gravity field to 3 s under the traveling magnetic field and average flow rate of the melt increases from 1.6 to 8.68 cm3/s; the change law of the cross-section morphology of the gallium melt during the mold filling is that at first, the cross-section area does not change, then it decreases gradually. When the front of the melt reaches the end of the mold cavity, the front melt will backfill the mold; the wider the width of mold cavity, the better the mold filling ability. The mold filling ability of gallium melt in mold with upper magnetic conductor is better than that without upper magnetic conductor.

Sweet spot prediction in tight sandstone reservoir based on well-bore rock physical simulation

To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.

Physical simulation of rock burst induced by stress waves

The behavior of stress wave propagation in rock walls and the process of rock bursts were simulated by application tests of material similar to rock. Results show that 1) the attenuation characteristics of stress waves were related to the material proper-ties, stress waves attenuate more quickly in soft material and 2) when the explosion load was applied at the top of the roadway, the number and the length of the cracks increased with a decrease in the distance between the explosive point and roof of the roadway. When the distance was 280 mm, only some chips appeared near the source, when the distance was 210 mm, some small cracks started to appear near the road-rib and when the distance was reduced to 140 mm, larger cracks appeared at the road-rib. It can be concluded that, under a given stress the number of cracks is closely related to the intensity of stress waves. The cracks in the sur-rounding rock can be reduced by controlling the intensity of the stress waves and rock bursts can be avoided to some extent by pre-venting the formation of layered crack structures. A new experimental approach has been provided for studying rock bursts by using physical simulation.

A Physical Simulation Test for the RockBurst in Tunnels

According to the test results of the physical and mechanical properties of similar materials in various quality mixture, a type of material with obvious tendency of rockburst was selected to produce a large-size model to simulate rockburst phenomena in tunnels. The prototype model comes from a typical section of diversion tunnels in Jinping Hydropower Station in China. The simulation of excavating tunnels is carried out by opening a hole in the model after loading. The modeling results indicated that under the condition of normal stresses in the model boundaries the arch top, spandrel and side walls of the tunnel produced an obvious jump reaction of stress and strain and the acoustic emission counts of the surrounding rock also increased rapidly in a different time period after the "tunnel" excavation, showing the clear features of rockburst. The spalling, buckling and breaking occurred in the surrounding rock of model in conditions of over loading. It is concluded that the modeling tunnel segment in Jinping Hydropower Station is expected to form the tensile rockburst with the pattern of spalling, buckling and breaking.

Physical modeling of spent-nuclearfuel container

A new physical simulation model was developed to simulate the casting process of the ductile iron heavy section spent-nuclear-fuel container.In this physical simulation model,a heating unit with DR24 Fe-Cr-Al heating wires was used to compensate the heat loss across the non-natural surfaces of the sample,and a precise and reliable casting temperature controlling/monitoring system was employed to ensure the thermal behavior of the simulated casting to be similar to the actual casting.Also,a mould system was designed,in which changeable mould materials can be used for both the outside and inside moulds for different applications.The casting test was carried out with the designed mould and the cooling curves of central and edge points at different isothermal planes of the casting were obtained.Results show that for most isothermal planes,the temperature control system can keep the temperature differences within 6 ℃ between the edge points and the corresponding center points,indicating that this new physical simulation model has high simulation accuracy,and the mould developed can be used for optimization of casting parameters of spent-nuclear-fuel container,such as composition of ductile iron,the pouring temperature,the selection of mould material and design of cooling system.In addition,to maintain the spheroidalization of the ductile iron,the force-chilling should be used for the current physical simulation to ensure the solidification of casting in less than 2 h.

Physical simulation of hydrodynamic conditions in high rank coalbed methane reservoir formation

In order to select highly productive and enriched areas of high rank coalbed methane reservoirs, based on hydrologic geology as one of the main factors controlling coalbed methane （CBM） reservoir formations, the effect of hydrodynamic forces controlling CBM reservoir formations was studied by a physical simulation experiment in which we used CBM reservoir simulation facilities. The hydrodynamic conditions of high coal rank reservoirs in the Qinshui basin were analyzed. Our experiment shows the following results： under strong hydrodynamic alternating action, 6C~ of coalbed methane reservoir changed from the start at -2.95% ~ -3.66%, and the lightening process occurred in phases; the CI-I4 volume reduced from 96.35% to 12.42%; the CO2 vo- lume decreased from 0.75% in sample 1 to 0.68% in sample 2, then rose to 1.13% in sample 3; the N2 volume changed from 2.9% in sample 1 to 86.45% in sample 3. On one hand, these changes show the complexity of CBM reservoir formation; on the other hand, they indicate that strong hydrodynamic actions have an unfavorable impact on CBM reservoir formation. It was found that the gas volume and hydrodynamic intensity were negatively correlated and low hydrodynamic flow conditions might result in highly productive and enriched areas of high rank CBM.