Laminates with alternating layers of NiCoCrAlY and NiCr were fabricated by using electron beam physical vapor deposition (EB-PVD) method. The influence of the substrate temperature on morphology of the laminates was i...Laminates with alternating layers of NiCoCrAlY and NiCr were fabricated by using electron beam physical vapor deposition (EB-PVD) method. The influence of the substrate temperature on morphology of the laminates was investigated. The results show that in order to produce NiCoCrAlY/NiCr laminates with lower porosity, higher substrate temperature is required. The mechanical properties of the as-deposited samples and heat-treated samples were examined using tensile tests. The stress-strain curve of the as-deposited laminate shows a typical characteristic of multilayered materials and the fracture behavior is improved by annealing the samples at high temperatures. The tensile strength of the samples annealed at 760℃ is 658.4MPa, and the elongation reaches 6.2%.展开更多
By using physical vapor deposition(PVD)to grow metallic nanorods,the characteristic length is controllable,which can be identified by two different growth modes:Mode I and Mode II.In Mode I,the growth of metallic nano...By using physical vapor deposition(PVD)to grow metallic nanorods,the characteristic length is controllable,which can be identified by two different growth modes:Mode I and Mode II.In Mode I,the growth of metallic nanorods is dominated by the monolayer surface steps.Whereas in Mode II,the growth mechanism is mainly determined by the multilayer surface steps.In this work,we focused on the analysis of the physical process of Mode I,in which the adatoms diffuse on the monolayer surface at beginning,then diffuse down to the next monolayer surface,and finally result in the metallic nanorods growth.Based on the physical process,both the variations of the characteristic length and the numerical solutions were theoretically proposed.In addition,the twodimensional(2 D)lattice kinetic Monte Carlo simulations were employed to verify the theoretical derivation of the metallic nanorods growth.Our results pay a new way for modifying the performance of metallic nanorods-based applications and devices.展开更多
A two-dimensional Kinetic Monte Carlo method has been developed for simulating the physical vapor deposition of thin Cu films on Cu substrate. An improved embedded atom method was used to calculate the interatomic pot...A two-dimensional Kinetic Monte Carlo method has been developed for simulating the physical vapor deposition of thin Cu films on Cu substrate. An improved embedded atom method was used to calculate the interatomic potential and determine the diffusion barrier energy and residence time. Parameters, including incident angle,deposition rate and substrate temperature, were investigated and discussed in order to find their influences on the thin film morphology.展开更多
Ti-Al thin sheet with dimension of 450 mm×450 mm×0.2 mm was prepared by electron beam physical vapor deposition(EB-PVD) technology. The surface and cross-section pattern of as-deposited sample were studied b...Ti-Al thin sheet with dimension of 450 mm×450 mm×0.2 mm was prepared by electron beam physical vapor deposition(EB-PVD) technology. The surface and cross-section pattern of as-deposited sample were studied by SEM and AFM,and then the composition and phase were analysed by XRD and EPMA. Finally,the effect on deposit by re-evaporation of Al was explored by calculating the ratio of re-evaporating capacity with depositing capacity of Al on the substrate. The results indicate that the evaporation process with Nb addition into the molten pool makes it earlier to reach the steady-state. The existing equiaxed crystal and columnar crystal along the cross-sectional may be caused by the transformation latent heat released during the transition course of atoms from gaseous state to solid state. The effect on deposit by re-evaporation of Al can be neglected because the re-evaporating capacity of Al is far below that of the depositing capacity.展开更多
The TiAl-based alloys sheet with 150 mm×100 mm×0.4 mm and the TiAl/Nb laminated composites with 150 mm×100 mm×0.2 mm were fabricated by using electron beam-physical vapor deposition(EB-PVD) method,...The TiAl-based alloys sheet with 150 mm×100 mm×0.4 mm and the TiAl/Nb laminated composites with 150 mm×100 mm×0.2 mm were fabricated by using electron beam-physical vapor deposition(EB-PVD) method, respectively. The microstructure and properties of the sheet were investigated by AFM, SEM and EDS. The results show that the TiAl based alloys sheet has a good surface quality, and its microstructure is columnar crystal. The component of the alloys indicates a regular and periodical gradient change which leads to the spontaneous delamination along the normal direction of substrate. In the TiAl/Nb laminated composites alternating overlaid by TiAl of 24 layers and Nb of 23 layers, the interface of each layer evenly distributed throughout the cross-section is transparent, and the interlayer spacing is about 8μm. The component of TiAl layers also changes regularly along the normal direction of substrate, but no delamination phenomenon is found. The TiAl/Nb laminated composites have better ductility than the TiAl-based alloys sheet.展开更多
The coatings of W-Ti carbides on the surface of diamond was obtained by using physical vapor deposition (PVD), during which WO3 powders pre-treated with hydrofluoric acid were reduced by titanium hydride in vacuum at ...The coatings of W-Ti carbides on the surface of diamond was obtained by using physical vapor deposition (PVD), during which WO3 powders pre-treated with hydrofluoric acid were reduced by titanium hydride in vacuum at 850 ℃. The resistance of diamond to corrosion at high-temperature was investigated. The formation of W-Ti carbides on the surface of diamond was verified by X-ray diffraction analysis, the interface state between diamond and matrix in metaLbase diamond composite was observed by scanning electron microscope. The results showed that the carbide coating is easy to be formed at low deposition temperature on the surface of diamond, while the resistance of diamond to corrosion at highutemperature and the strength of bonding between diarnond and metal matrix are effectively improved.展开更多
Over the past years, great achievements have been made in the development of coating technologies for surface improvement of aluminum alloys. Despite these achievements, the role in the market strongly depends on the ...Over the past years, great achievements have been made in the development of coating technologies for surface improvement of aluminum alloys. Despite these achievements, the role in the market strongly depends on the ability of surface coating technology under technical and economic considerations to meet the increased demands for heavy tribological applications of aluminum alloys. Microplasma oxidation (MPO) technology has recently been studied as a novel and effective means to provide thick and hard ceramic coating with improved properties such as excellent load-bearing and wear resistance properties on aluminum alloys. The present work covers the evaluation of the performances of current single and duplex coatings combining MPO, physical vapor deposition (PVD), and plasma assisted chemical vapor deposition (PACVD) coatings on aluminum alloys. It suggests that the MPO coating is a promising candidate for design engineers to apply aluminum alloys to heavy load-bearing applications. The prospective future for the research on MPO coatings is introduced as well.展开更多
Cathodic arc evaporation is a well-established physical vapor deposition technique which is characterized by a high degree of ionization and high deposition rate. So far, this technique has been mainly used for the de...Cathodic arc evaporation is a well-established physical vapor deposition technique which is characterized by a high degree of ionization and high deposition rate. So far, this technique has been mainly used for the deposition of tribological coatings. In this study, anti-corrosive and electrical conductive carbon-based coatings with a metallic interlayer were prepared on stainless steel substrates as surface modification for metallic bipolar plates. Hereby, the influence of the deposition temperature during the deposition of the carbon top layer was investigated. Raman spectroscopy revealed differences in the microstructure at 200°C compared to 300°C and 100°C. Measurements of the interfacial contact resistance showed that the deposited coatings significantly improve the electrical conductivity. There are only minor differences between the different carbon top layers. The corrosion resistance of the coatings was studied via potentiodynamic polarization at room temperature and 80°C. Experiments showed that the coating with a carbon top layer deposited at 200°C, considerably reduces the current density and thus corrosion of the substrate is suppressed.展开更多
Zinc alloy coating attracted much attention due to its high anti-corrosive properties.Particularly,zinc alloy coatings containing magnesium was considered a promising metallic alloy due to a remarkable improvement of ...Zinc alloy coating attracted much attention due to its high anti-corrosive properties.Particularly,zinc alloy coatings containing magnesium was considered a promising metallic alloy due to a remarkable improvement of corrosion resistance.The proper magnesium content for Zn-Mg alloy coatings was studied.The samples were prepared using thermal evaporation method.The influence of Zn-Mg alloy coating on corrosion resistance was evaluated using immersion test,potentiodynamic test,and galvanic test in 3% NaCl solution at room temperature.The results show that the corrosion resistance of Zn-Mg alloy coatings is strongly dependent on magnesium content.Corrosion potential decreases with increasing magnesium content,whereas current density increases up to 15% magnesium content,and passivity region was found only in Zn-Mg coatings.展开更多
Two-dimensional(2D) PbI_2 flakes have been attracting intensive attention as one potential candidate for the modern optoelectronics. However, suffered from the instability of kinetics-driven growth, the fabricated 2D ...Two-dimensional(2D) PbI_2 flakes have been attracting intensive attention as one potential candidate for the modern optoelectronics. However, suffered from the instability of kinetics-driven growth, the fabricated 2D PbI_2 flakes have a wide dimensional distribution even under the same conditions. Herein, a novel facile space confined physical vapor deposition(PVD) process is provided to synthesize uniform triangle PbI_2 flakes with high quality. The confined space provides a relatively stable growth environment that renders more control on the growth kinetics, leading to highly uniform triangle PbI_2 flakes with the average size of 5 mm and thickness of 17 nm. Moreover, as-fabricated PbI_2-based photodetectors show promising stable and flexible optoelectronic performances to 470 nm light, including high responsivity(0.72 AW^(-1)), large on/off ratio up to 900, fast photoresponse speed(rise time of 13.5 ms and decay time of 20 ms) and high detectivity(1.04×10^(10) Jones). The well-controllable growth of the uniform triangle PbI_2 flakes and the detailed exploration of their optoelectronic properties are particularly valuable for their further practical applications.展开更多
Plasma spray–physical vapor deposition(PS–PVD)is a unique technology that enables highly tailorable functional films and coatings with various rare metal elements to be processed.This technology bridges the gap betw...Plasma spray–physical vapor deposition(PS–PVD)is a unique technology that enables highly tailorable functional films and coatings with various rare metal elements to be processed.This technology bridges the gap between conventional thermal spray and vapor deposition and provides a variety of coating microstructures composed of vapor,liquid,and solid deposition units.The PS–PVD technique serves a broad range of applications in the fields of thermal barrier coatings(TBCs),environmental barrier coatings(EBCs),oxygen permeable films,and electrode films.It also represents the development direction of high-performance TBC/EBC preparation technologies.With the PS–PVD technique,the composition of the deposition unit determines the microstructure of the coating and its performance.When coating materials are injected into a nozzle and transported into the plasma jet,the deposition unit generated by a coating material is affected by the plasma jet characteristics.However,there is no direct in situ measurement method of material transfer and deposition processes in the PS–PVD plasma jet,because of the extreme conditions of PS–PVD such as a low operating pressure of*100 Pa,temperatures of thousands of degrees,and a thin and high-velocity jet.Despite the difficulties,the transport and transformation behaviors of the deposition units were also researched by optical emission spectroscopy,observation of the coating microstructure and other methods.This paper reviews the progress of PS–PVD technologies considering the preparation of advanced thermal barrier coatings from the perspective of the transport and transformation behaviors of the deposition units.The development prospects of new high-performance TBCs using the PS–PVD technique are also discussed.展开更多
Thickness and component distributions of large-area thin films are an issue of in-ternational concern in the field of material processing. The present work employs experiments and direct simulation Monte Carlo (DSMC) ...Thickness and component distributions of large-area thin films are an issue of in-ternational concern in the field of material processing. The present work employs experiments and direct simulation Monte Carlo (DSMC) method to investigate three-dimensional low-density, non-equilibrium jets of yttrium and titanium vapor atoms in an electron-beams physical vapor deposition (EBPVD) system furnished with two or three electron-beams, and obtains their deposition thickness and component distributions onto 4-inch and 6-inch mono-crystal silicon wafers. The DSMC results are found in excellent agreement with our measurements, such as evaporation rates of yttrium and titanium measured in-situ by quartz crystal reso-nators, deposited film thickness distribution measured by Rutherford backscat-tering spectrometer (RBS) and surface profilometer and deposited film molar ratio distribution measured by RBS and inductively coupled plasma atomic emission spectrometer (ICP-AES). This can be taken as an indication that a combination of DSMC method with elaborate measurements may be satisfactory for predicting and designing accurately the transport process of EBPVD at the atomic level.展开更多
Physical vapor deposition method was employed to deposit antimony telluride （Sb2Te3） crystals in a dual-zone furnace. The microstructure, surface topography and composition of samples were characterized using X-ray ...Physical vapor deposition method was employed to deposit antimony telluride （Sb2Te3） crystals in a dual-zone furnace. The microstructure, surface topography and composition of samples were characterized using X-ray diffraction, atomic force and scanning electron microscopy. Seebeck coefficient （Sic）, electrical conductivity （σ⊥c） as well as power factor （PF） were enhanced for pure Sb2Te3 samples upon annealing, and the samples annealed at 473 K exhibited the highest PF of 3.16 × 10^-3 W m-1K-2 with an enhancement of 22% in the figure of merit （Z）. When the delivered dose of 60Co gamma radiation was increased from 0 to 30 kGy in the stoichiometric crystals, σ⊥c decreased due to the decrease in mobility. As a result of the increase in S, PF and Z improved by 12.11 and 13.7%, respectively, in the 30 kGy gamma- irradiated crystals. Both RH （BIIc） and S⊥c were positive, suggesting that the prepared Sb2Te3 crystals retained the p-type semiconductivity after these treatments.展开更多
文摘Laminates with alternating layers of NiCoCrAlY and NiCr were fabricated by using electron beam physical vapor deposition (EB-PVD) method. The influence of the substrate temperature on morphology of the laminates was investigated. The results show that in order to produce NiCoCrAlY/NiCr laminates with lower porosity, higher substrate temperature is required. The mechanical properties of the as-deposited samples and heat-treated samples were examined using tensile tests. The stress-strain curve of the as-deposited laminate shows a typical characteristic of multilayered materials and the fracture behavior is improved by annealing the samples at high temperatures. The tensile strength of the samples annealed at 760℃ is 658.4MPa, and the elongation reaches 6.2%.
文摘By using physical vapor deposition(PVD)to grow metallic nanorods,the characteristic length is controllable,which can be identified by two different growth modes:Mode I and Mode II.In Mode I,the growth of metallic nanorods is dominated by the monolayer surface steps.Whereas in Mode II,the growth mechanism is mainly determined by the multilayer surface steps.In this work,we focused on the analysis of the physical process of Mode I,in which the adatoms diffuse on the monolayer surface at beginning,then diffuse down to the next monolayer surface,and finally result in the metallic nanorods growth.Based on the physical process,both the variations of the characteristic length and the numerical solutions were theoretically proposed.In addition,the twodimensional(2 D)lattice kinetic Monte Carlo simulations were employed to verify the theoretical derivation of the metallic nanorods growth.Our results pay a new way for modifying the performance of metallic nanorods-based applications and devices.
文摘A two-dimensional Kinetic Monte Carlo method has been developed for simulating the physical vapor deposition of thin Cu films on Cu substrate. An improved embedded atom method was used to calculate the interatomic potential and determine the diffusion barrier energy and residence time. Parameters, including incident angle,deposition rate and substrate temperature, were investigated and discussed in order to find their influences on the thin film morphology.
基金Project(NCET2004) supported by the Program for New Century Excellent Talents in University, China
文摘Ti-Al thin sheet with dimension of 450 mm×450 mm×0.2 mm was prepared by electron beam physical vapor deposition(EB-PVD) technology. The surface and cross-section pattern of as-deposited sample were studied by SEM and AFM,and then the composition and phase were analysed by XRD and EPMA. Finally,the effect on deposit by re-evaporation of Al was explored by calculating the ratio of re-evaporating capacity with depositing capacity of Al on the substrate. The results indicate that the evaporation process with Nb addition into the molten pool makes it earlier to reach the steady-state. The existing equiaxed crystal and columnar crystal along the cross-sectional may be caused by the transformation latent heat released during the transition course of atoms from gaseous state to solid state. The effect on deposit by re-evaporation of Al can be neglected because the re-evaporating capacity of Al is far below that of the depositing capacity.
基金Projects(90205034, 90405016) supported by the National Natural Science Foundation of China
文摘The TiAl-based alloys sheet with 150 mm×100 mm×0.4 mm and the TiAl/Nb laminated composites with 150 mm×100 mm×0.2 mm were fabricated by using electron beam-physical vapor deposition(EB-PVD) method, respectively. The microstructure and properties of the sheet were investigated by AFM, SEM and EDS. The results show that the TiAl based alloys sheet has a good surface quality, and its microstructure is columnar crystal. The component of the alloys indicates a regular and periodical gradient change which leads to the spontaneous delamination along the normal direction of substrate. In the TiAl/Nb laminated composites alternating overlaid by TiAl of 24 layers and Nb of 23 layers, the interface of each layer evenly distributed throughout the cross-section is transparent, and the interlayer spacing is about 8μm. The component of TiAl layers also changes regularly along the normal direction of substrate, but no delamination phenomenon is found. The TiAl/Nb laminated composites have better ductility than the TiAl-based alloys sheet.
文摘The coatings of W-Ti carbides on the surface of diamond was obtained by using physical vapor deposition (PVD), during which WO3 powders pre-treated with hydrofluoric acid were reduced by titanium hydride in vacuum at 850 ℃. The resistance of diamond to corrosion at high-temperature was investigated. The formation of W-Ti carbides on the surface of diamond was verified by X-ray diffraction analysis, the interface state between diamond and matrix in metaLbase diamond composite was observed by scanning electron microscope. The results showed that the carbide coating is easy to be formed at low deposition temperature on the surface of diamond, while the resistance of diamond to corrosion at highutemperature and the strength of bonding between diarnond and metal matrix are effectively improved.
文摘Over the past years, great achievements have been made in the development of coating technologies for surface improvement of aluminum alloys. Despite these achievements, the role in the market strongly depends on the ability of surface coating technology under technical and economic considerations to meet the increased demands for heavy tribological applications of aluminum alloys. Microplasma oxidation (MPO) technology has recently been studied as a novel and effective means to provide thick and hard ceramic coating with improved properties such as excellent load-bearing and wear resistance properties on aluminum alloys. The present work covers the evaluation of the performances of current single and duplex coatings combining MPO, physical vapor deposition (PVD), and plasma assisted chemical vapor deposition (PACVD) coatings on aluminum alloys. It suggests that the MPO coating is a promising candidate for design engineers to apply aluminum alloys to heavy load-bearing applications. The prospective future for the research on MPO coatings is introduced as well.
文摘Cathodic arc evaporation is a well-established physical vapor deposition technique which is characterized by a high degree of ionization and high deposition rate. So far, this technique has been mainly used for the deposition of tribological coatings. In this study, anti-corrosive and electrical conductive carbon-based coatings with a metallic interlayer were prepared on stainless steel substrates as surface modification for metallic bipolar plates. Hereby, the influence of the deposition temperature during the deposition of the carbon top layer was investigated. Raman spectroscopy revealed differences in the microstructure at 200°C compared to 300°C and 100°C. Measurements of the interfacial contact resistance showed that the deposited coatings significantly improve the electrical conductivity. There are only minor differences between the different carbon top layers. The corrosion resistance of the coatings was studied via potentiodynamic polarization at room temperature and 80°C. Experiments showed that the coating with a carbon top layer deposited at 200°C, considerably reduces the current density and thus corrosion of the substrate is suppressed.
基金supported by the Smart Coating Steel Development Center,World Premier Materials (WPM) Program of the Ministry of Knowledge Economy of Korea and Korea Maritime University
文摘Zinc alloy coating attracted much attention due to its high anti-corrosive properties.Particularly,zinc alloy coatings containing magnesium was considered a promising metallic alloy due to a remarkable improvement of corrosion resistance.The proper magnesium content for Zn-Mg alloy coatings was studied.The samples were prepared using thermal evaporation method.The influence of Zn-Mg alloy coating on corrosion resistance was evaluated using immersion test,potentiodynamic test,and galvanic test in 3% NaCl solution at room temperature.The results show that the corrosion resistance of Zn-Mg alloy coatings is strongly dependent on magnesium content.Corrosion potential decreases with increasing magnesium content,whereas current density increases up to 15% magnesium content,and passivity region was found only in Zn-Mg coatings.
基金supported by the National Natural Science Foundation of China (51472097, 91622117, 21501060, and 51727809)the National Key Research and Development Program (2016YFB0401100)+1 种基金the National Basic Research Program of China (2015CB932600)the Fundamental Research Funds for the Central University (2017KFKJXX007, 2015ZDTD038)
文摘Two-dimensional(2D) PbI_2 flakes have been attracting intensive attention as one potential candidate for the modern optoelectronics. However, suffered from the instability of kinetics-driven growth, the fabricated 2D PbI_2 flakes have a wide dimensional distribution even under the same conditions. Herein, a novel facile space confined physical vapor deposition(PVD) process is provided to synthesize uniform triangle PbI_2 flakes with high quality. The confined space provides a relatively stable growth environment that renders more control on the growth kinetics, leading to highly uniform triangle PbI_2 flakes with the average size of 5 mm and thickness of 17 nm. Moreover, as-fabricated PbI_2-based photodetectors show promising stable and flexible optoelectronic performances to 470 nm light, including high responsivity(0.72 AW^(-1)), large on/off ratio up to 900, fast photoresponse speed(rise time of 13.5 ms and decay time of 20 ms) and high detectivity(1.04×10^(10) Jones). The well-controllable growth of the uniform triangle PbI_2 flakes and the detailed exploration of their optoelectronic properties are particularly valuable for their further practical applications.
基金financially supported by the National Key R&D Plan(No.2017YFB0306103)the Fundamental Research Funds for the Central Universitiesthe National Program for Support of Top-notch Young Professionals。
文摘Plasma spray–physical vapor deposition(PS–PVD)is a unique technology that enables highly tailorable functional films and coatings with various rare metal elements to be processed.This technology bridges the gap between conventional thermal spray and vapor deposition and provides a variety of coating microstructures composed of vapor,liquid,and solid deposition units.The PS–PVD technique serves a broad range of applications in the fields of thermal barrier coatings(TBCs),environmental barrier coatings(EBCs),oxygen permeable films,and electrode films.It also represents the development direction of high-performance TBC/EBC preparation technologies.With the PS–PVD technique,the composition of the deposition unit determines the microstructure of the coating and its performance.When coating materials are injected into a nozzle and transported into the plasma jet,the deposition unit generated by a coating material is affected by the plasma jet characteristics.However,there is no direct in situ measurement method of material transfer and deposition processes in the PS–PVD plasma jet,because of the extreme conditions of PS–PVD such as a low operating pressure of*100 Pa,temperatures of thousands of degrees,and a thin and high-velocity jet.Despite the difficulties,the transport and transformation behaviors of the deposition units were also researched by optical emission spectroscopy,observation of the coating microstructure and other methods.This paper reviews the progress of PS–PVD technologies considering the preparation of advanced thermal barrier coatings from the perspective of the transport and transformation behaviors of the deposition units.The development prospects of new high-performance TBCs using the PS–PVD technique are also discussed.
基金the National Natural Science Foundation of China (Grant Nos. 90205024, 10502051 and 10621202)
文摘Thickness and component distributions of large-area thin films are an issue of in-ternational concern in the field of material processing. The present work employs experiments and direct simulation Monte Carlo (DSMC) method to investigate three-dimensional low-density, non-equilibrium jets of yttrium and titanium vapor atoms in an electron-beams physical vapor deposition (EBPVD) system furnished with two or three electron-beams, and obtains their deposition thickness and component distributions onto 4-inch and 6-inch mono-crystal silicon wafers. The DSMC results are found in excellent agreement with our measurements, such as evaporation rates of yttrium and titanium measured in-situ by quartz crystal reso-nators, deposited film thickness distribution measured by Rutherford backscat-tering spectrometer (RBS) and surface profilometer and deposited film molar ratio distribution measured by RBS and inductively coupled plasma atomic emission spectrometer (ICP-AES). This can be taken as an indication that a combination of DSMC method with elaborate measurements may be satisfactory for predicting and designing accurately the transport process of EBPVD at the atomic level.
文摘Physical vapor deposition method was employed to deposit antimony telluride （Sb2Te3） crystals in a dual-zone furnace. The microstructure, surface topography and composition of samples were characterized using X-ray diffraction, atomic force and scanning electron microscopy. Seebeck coefficient （Sic）, electrical conductivity （σ⊥c） as well as power factor （PF） were enhanced for pure Sb2Te3 samples upon annealing, and the samples annealed at 473 K exhibited the highest PF of 3.16 × 10^-3 W m-1K-2 with an enhancement of 22% in the figure of merit （Z）. When the delivered dose of 60Co gamma radiation was increased from 0 to 30 kGy in the stoichiometric crystals, σ⊥c decreased due to the decrease in mobility. As a result of the increase in S, PF and Z improved by 12.11 and 13.7%, respectively, in the 30 kGy gamma- irradiated crystals. Both RH （BIIc） and S⊥c were positive, suggesting that the prepared Sb2Te3 crystals retained the p-type semiconductivity after these treatments.
