Pit Bearing Capacity Effect on Status of Soil Plug During Pile Driving in Ocean Engineering

Foundation piles of the offshore oil platforms in the Bohai Bay are usually longer than 100 m with a diameter larger than 2 m. Driving such long and large-sized piles into the ground is a difficult task. It needs a comprehensive consider ation of the pile dimensions, soil properties and the hammer energy. Thoughtful drivability analysis has to be performed in the design stage. It has been shown that judging whether the soil column inside the pile is fully plugged, which makes the pile behave as close-ended, strongly influences the accuracy of drivability analysis. Engineering practice repeatedly indicates that the current methods widely used for soil plug judgment often give incorrect results, leading the designers to make a wrong decision. It has been found that this problem is caused by the ignorance of the bearing capacity provided by the soil surrounding the pile. Based on the Terzaghi＇s bearing capacity calculation method for deep foundation, a new approach for judging soil plug status is put forward, in which the surcharge effect has been considered and the dynamic effect coefficient is included. This approach has been applied to some practical engineering projects successfully, which may give more reasonable results than the currently used method does.

Ultimate Lateral Capacity of Rigid Pile in c–φ Soil

To date no analytical solution of the pile ultimate lateral capacity for the general c–φ soil has been obtained. In the present study, a new dimensionless embedded ratio was proposed and the analytical solutions of ultimate lateral capacity and rotation center of rigid pile in c–φ soils were obtained. The results showed that both the dimensionless ultimate lateral capacity and dimensionless rotation center were the univariate functions of the embedded ratio. Also,the ultimate lateral capacity in the c–φ soil was the combination of the ultimate lateral capacity（f;） in the clay, and the ultimate lateral capacity（f;） in the sand. Therefore, the Broms chart for clay, solution for clay（φ=0） put forward by Poulos and Davis, solution for sand（c=0） obtained by Petrasovits and Awad, and Kondner’s ultimate bending moment were all proven to be the special cases of the general solution in the present study. A comparison of the field and laboratory tests in 93 cases showed that the average ratios of the theoretical values to the experimental value ranged from 0.85 to 1.15. Also, the theoretical values displayed a good agreement with the test values.

Regressive approach for predicting bearing capacity of bored piles from cone penetration test data

In this study, th e least sq u are su p p o rt v ecto r m achine （LSSVM） alg o rith m w as applied to predicting th ebearing capacity o f b ored piles e m b ed d ed in sand an d m ixed soils. Pile g eo m etry an d cone p e n e tra tio nte s t （CPT） resu lts w ere used as in p u t variables for pred ictio n o f pile bearin g capacity. The d ata u se d w erecollected from th e existing litera tu re an d consisted o f 50 case records. The application o f LSSVM w ascarried o u t by dividing th e d ata into th re e se ts： a train in g se t for learning th e pro b lem an d obtain in g arelationship b e tw e e n in p u t variables an d pile bearin g capacity, and testin g an d validation sets forevaluation o f th e predictive an d g en eralization ability o f th e o b tain ed relationship. The predictions o f pilebearing capacity by LSSVM w ere evaluated by com paring w ith ex p erim en tal d ata an d w ith th o se bytrad itio n al CPT-based m eth o d s and th e gene ex pression pro g ram m in g （GEP） m odel. It w as found th a t th eLSSVM perform s w ell w ith coefficient o f d eterm in atio n , m ean, an d sta n d ard dev iatio n equivalent to 0.99,1.03, an d 0.08, respectively, for th e testin g set, an d 1, 1.04, an d 0.11, respectively, for th e v alidation set. Thelow values o f th e calculated m ean squared e rro r an d m ean ab so lu te e rro r indicated th a t th e LSSVM w asaccurate in p redicting th e pile bearing capacity. The results o f com parison also show ed th a t th e p roposedalg o rith m p red icted th e pile bearin g capacity m ore accurately th a n th e trad itio n al m eth o d s including th eGEP m odel.

Estimation of Axial Pile Bearing Capacity According to Shear Strength Parameters of Soil

At pesent, it is very popular to estimate pile bearing capacity by use of empirical formula and physical indexes of soil provided in the design codes for civil construction in China. This paper attempts to apply mechanical indexes of soil and semi-empirical formulas, which are based on soil mechanical theories and were summarized and presented by Meyerhof in 1976, to calculate the axial pile bearing capacity. Loading test results of 24 single piles in Tianjin area have been collected and compared with the proposed calulation approach.

Study of the Bearing Capacity at the Variable Cross-Section of A Riser- Surface Casing Composite Pile

Reducing the cost of offshore platform construction is an urgent issue for marginal oilfield development.The offshore oil well structure includes a riser and a surface casing.The riser,surface casing and oil well cement can be considered special variable cross-section piles.Replacing or partially replacing the steel pipe pile foundation with a variable cross-section pile to provide the required bearing capacity for an offshore oil platform can reduce the cost of foundation construction and improve the economic efficiency of production.In this paper,the finite element analysis method is used to investigate the variable cross-section bearing mode of composite piles composed of a riser and a surface casing in saturated clay under a vertical load.The calculation formula of the bearing capacity at the variable section is derived based on the theory of spherical cavity expansion,the influencing factors of the bearing capacity coefficient N_(c) are revealed,and the calculation method of N_(c) is proposed.By comparing the calculation results with the results of the centrifuge test,the accuracy and applicability of the calculation method are verified.The results show that the riser composite pile has a rigid core in the soil under the variable cross-section,which increases the bearing capacity at the variable cross-section.

Uplift Pile Test in Rocks and Its Bearing Capacity

This paper reports in situ tension test and laboratory model test for large diameter, manually digging anchorage piles in the 2nd Luzhou Changjiang Bridge. Tension behavior, uplift bearing capacity and influence of rock characteristics on bearing capacity are discussed. Proposes are presented with respect to issues related to the construction and design of uplift piles.

3D FE Analysis of Effect of Ground Subsidence and Piled Spacing on Ultimate Bearing Capacity of Piled Raft and Axial Force of Piles in Piled Raft

The effects of ground subsidence and piled spacing on axial force of piles in squared piled rafts were investigated using numerical analysis. Two cases of piled rafts in soft clay including case 1 (s = 2d) and case 2 (s = 4d) with s and d were piled spacing and piled diameter respectively were considered in this study. Undrained (without ground water pumping) and drained (with ground water pumping) conditions were applied in each case in order to evaluate variations of ultimate bearing capacity of piled raft and axial force of the piles in piled raft. The results showed that ultimate bearing capacity increased about 25% for undrained condition and about 32% for drained condition when piled spacing increased from 2d to 4d. In the same piled spacing, axial force of the piles increased about 9% for piled spacing of 2d and 7% for piled spacing of 4d when drained condition was applied. When piled spacing increased 2 times (2d to 4d), the axial force of piles increased about 7% for undrained condition and about 5% for drained condition.

Evaluation of the Ultimate Capacity of Friction Piles

The precise prediction of maximum load carrying capacity of bored piles is a complex problem because the load is a function of a large number of factors. These factors include method of boring, method of concreting, quality of concrete, expertise of the construction staff, the ground conditions and the pile geometry. To ascertain the field performance and estimate load carrying capacities of piles, in-situ pile load tests are conducted. Due to practical and time constraints, it is not possible to load the pile up-to failure. In this study, field pile load test data is analyzed to estimate the ultimate load for friction piles. The analysis is based on three pile load test results. The tests are conducted at the site of The Cultural and Recreational Complex project in Port Said, Egypt. Three pile load tests are performed on bored piles of 900 mm diameter and 50 m length. Geotechnical investigations at the site are carried out to a maximum depth of 60 m. Ultimate capacities of piles are determined according to different methods including Egyptian Code of practice (2005), Tan-gent-tangent, Hansen (1963), Chin (1970), Ahmed and Pise (1997) and Decourt (1999). It was concluded that approxi- mately 8% of the ultimate load is resisted by bearing at the base of the pile, and that up to 92% of the load is resisted by friction along the shaft. Based on a comparison of pile capacity predictions using different method, recommendations are made. A new method is proposed to calculate the ultimate capacity of the pile from pile load test data. The ultimate capacity of the bored piles predicted using the proposed method appears to be reliable and compares well to different available methods.

Response of carrying capacity of piles induced by adjacent Metro tunneling

Construction of tunnels in urban areas requires assessment of the impact of tunneling on the stability and integrity of existing pile foundations.We have focused our attention to the analysis of the carrying capacity of pile foundations provided by the impact of construction of urban tunnels on adjacent pile foundations,under the engineering background of the construction of the # 2 Line of the Guangzhou subway.It is carried out using a fast Lagrangian analysis of a continuum in a 3D numerical code,which is an elastoplastic three-dimensional finite difference model,to simulate the response of piles under the entire process of metro tunneling(deactivation of soil element and activation of the lining).The adjacent stratum around the tunnel is classified into three regions:Zone I(upper adjacent stratum of tunnel),Zone II(45°-upper-lateral adjacent stratum of tunnel) and Zone III(lateral adjacent stratum of tunnel).In each region one typical pile is chosen to be calculated and analyzed in detail.Numerical simulations are mainly conducted at three points of each pile shaft:the side-friction force of the pile,the tip resistance of the pile and the axial loading of the pile.A contrasting analysis has been conducted both in the response of typical piles in different regions and from computer calculated values with site monitoring values.The results of numerical simulations show that the impact on carrying capacity of the piles lies mainly in the impact of construction of urban tunnels on the side-friction forces and the tip resistance of piles.The impact differs considerably among the different strata zones where the pile tips are located.The complicated rules of side-friction force and tip resistance of piles has resulted in complicated rules of pile axial loading thus,in the end,it impacts the carrying capacity of pile-foundations.It is necessary to take positive measures,such as stratum grouting stabilization or foundation underpinning,etc,to deal with the carrying capacity and the settlement of pile-foundations.The results are of value to similar engineering projects.

Vertical bearing capacity of pile based on load transfer model

The load transfer analytical method is applied to study the bearing mechanism of piles with vertical load in this paper. According to the different hardening rules of soil or rock around the pile shaft, such as work-softening, ideal elasto-plastic and work-hardening, a universal tri-linear load transfer model is suggested for the development of side and tip resistance by various types of soil (rock) with the consideration of sediment at the bottom of the pile. Based on the model, a formula is derived for the relationship between the settlement and load on the pile top to determine the vertical bearing capacity, taking into account such factors as the characteristics of the stratum, the side resistance along the shaft, and tip resistance under the pile tip. A close agreement of the calculated results with the measured data from a field test pile lends confidence to the future application of the present approach in engineering practice.

Finite element analysis of effect of soil displacement on bearing capacity of single friction pile

Effect of soil displacement on friction single pile in the cases of tunneling,surcharge load and uniform soil movement was discussed in details with finite element method.Lateral displacement of the pile caused by soil displacement reached about 90% of the total displacement,which means that P-Δ effect of axial load can be neglected.The maximum moment of pile decreased from 159 kN·m to 133 kN·m in the case of surcharge load when the axial load increased from 0 to the ultimate load.When deformation of pile caused by soil displacement is large,axial load applied on pile-head plays the role of reducing the maximum bending moment in concrete pile to some extent.When pile is on one side of the tunnel,soil displacements around the pile are all alike,which means that the soil pressures around the pile do not decrease during tunneling.Therefore,Q-s curve of the pile affected by tunneling is very close to that of pile in static loading test.Bearing capacities of piles influenced by surcharge load and uniform soil movement are 2480 kN and 2630 kN,respectively,which are a little greater than that of the pile in static loading test(2400 kN).Soil pressures along pile increase due to surcharge load and uniform soil movement,and so do the shaft resistances along pile,as a result,when rebars in concrete piles are enough,bearing capacity of pile affected by soil displacement increases compared with that of pile in static loading test.

Ultimate end bearing capacity of rock-socketed pile based on generalized nonlinear unified strength criterion

In order to study the mechanism of bearing behavior at the tip of a pile embedded in rock,the generalized nonlinear unified strength criterion and slip line principle for resolving the differential equation systems which govern the stress field were applied to derive the ultimate end bearing capacity based on some reasonable hypothesis and failure plane model.Both numerical simulation and test results were compared with the theoretic solution.The results show good consistency with each other and verify the validity of the present approach.The depth effect with respective to embedment ratio and other influence factors like geological strength index,intermediate principal stress,overburden factor,and damage on end bearing capacity were discussed in the analytical solution.The results show that the proposed yield criterion can be much better for investigating the ultimate end bearing performance of rock-socketed pile.The end bearing capacity increases with embedment ratio and the increasing degree is influenced intensely by the above parameters.Furthermore,ignoring intermediate stress effect would underestimate the strength properties of the rock material and lead to a very conservative estimation value.

Evaluation of ultimate bearing capacity of Y-shaped vibro-pile

Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's and ЪерезанцевВГ's methods for ultimate bearing capacity evaluation were proposed by considering the stress strength induced by friction resistance at pile head level of Y-pile. A new method to calculate the ultimate bearing capacity of Y-pile was also proposed based on the assumptions of soil failure mode at the tip of Y-pile and the use of Mohr-Coulomb soil yield criterion and Vesic compressive correction coefficient with the induced stresses in the ground. Based on the comparisons with the field static load test results, it is found that the improved Terzaghi's method gives higher ultimate capacity, while the other two methods shows good agreement with the field results.

Bearing capacity and mechanical behavior of CFG pile composite foundation

CFG pile (i.e., pile constructed by granular materials of cement, fly-ash and gravel) composite foundation is applied in subsoil treatment widely and successfully. In order to have a further study of this kind of subsoil treatment technology, the influencing factors and calculation methods of the vertical bearing capacity of single CFG pile and the CFG pile composite foundation were discussed respectively. And based on the obtained solutions, effects by the cushion and measurements to reduce negative friction area were analyzed. Moreover, the developing law of settlement and bearing capacity eigenvalue controlled by the material strength with the increase of load were given for the CFG composite foundation. The in-situ static load test was tested for CFG pile. The results of test show that the maximum test load or half of the ultimate load is used from all the points of test, the average bearing capacity eigenvalue of single pile is 390 kN, and slightly greater than the design value of bearing capacity. The bearing capacity eigenvalues of composite foundation for 3 piles are greater than 300 kPa, and the mechanical properties of CFG pile composite foundation are almost identical in the case of the same load and cushion thickness. The pile-soil stress ratio and the load-sharing ratio can be adjusted through setting up cushion thickness.

Analysis of bearing capacity of pile foundation in discontinued permafrost regions

Piles are the main building foundation in permafrost regions. Thawing the permafrost foundation would have a negative effect on a pile, and may cause damage to the building. This paper focuses on the effects of negative friction force due to the melt of permafrost, and presents four calculated methods for bearing capacity of a pile. An engineering station was taken as an example, where the lengths of a pile were compared based on four methods. Finally, quick field load tests were carried out, and some meaningful conclusions are presented. Thus, these analytical results can be used to design a pile for permafrost regions.

ON THE DRIVING BEHAVIOR，VARIABLE－DIAMETEREFFECT AND BEAKING CAPACITY OF DRIVENCAST－IN－SITU PILE WITHFLAT

ＯＮＴＨＥＤＲＩＶＩＮＧＢＥＨＡＶＩＯＲ，ＶＡＲＩＡＢＬＥ－ＤＩＡＭＥＴＥＲＥＦＦＥＣＴＡＮＤＢＥＡＫＩＮＧＣＡＰＡＣＩＴＹＯＦＤＫＩＶＥＮＣＡＳＴ－ＩＮ－ＳＩＴＵＰＩＬＥＷＩＴＨＦＬＡＴＯＶＥＲＳＩＺＥＴＩＰＳｈｉＰｅｉｄｏｎｇ，ＦｕＺｈｅｎｑｉｕ...

Axial Load Capacity of Cast in Place Piles from SPT and CPTU Data

This paper aims to deal with the assessment of axial load capacity for cast in place pile foundations, which are made by the earth drill method, by using the data taken from Standard Penetration Tests (SPTs) and Piezocone Penetration Tests (CPTUs). These tests were carried out as part of the investigation program for P.N.G. Terminal-Power Plant, near Semani beach, in Hoxhara marsh, in the western part of Albania. The design of axial load capacity of piles is based on empirical formula using SPT and CPTU values. This study presents the results of axial load capacity analysis of cast in place piles by different analytical calculation methods, which are based on in situ tests results, and also referring to the Building Standard Law of Japan. In the end of our work, differences between calculations methods by using different in situ tests results are shown in tables and graphs.

Infuencing Factors of Load Carrying Capacity and Cooperative Work Laws of Metro Uplift Piles

The buoyancy of groundwater can reduce the foundation bearing capa-city and cause the metro tunnels to float as a whole,which threatens the safety of structures seriously.Therefore,uplift piles are set up to improve the structural sta-bility.In this paper,FLAC3D software is used to establish the calculation models of pile foundation.The bearing failure process of uplift piles was simulated to study the influencing factors on single pile load bearing capacity as well as the cooperative work laws of pile groups.The load-displacement curves of pile top under different length-diameter ratios,pile soil interface characteristics and pile types are obtained,respectively.The results showed that,increasing the length-diameter ratio and the pile-soil interface roughness properdly can improve the bear-ing capacity of uplift piles.Besides,changing the shapes of constant pile section can also improve it,which has the most significant effect concerning of saving material cost.In the loading process of pile groups,the ultimate bearing capacity of corner pile is the biggest,the side pile is the next,and the center pile is the smallest.The de formation characteristics of pile top are as follows:the center pile is the biggest,the side pile is the next,and comer pile is the smallest.Combined with the results,the uplift resistance of group piles can be enhanced pertinently,and the conclusions provide guidance for the design and construction of up lift piles in the actual engineer.

New Method for Prediction Pile Capacity Executed by Continuous Flight Auger (CFA)

A study of piles is quit complex and the estimation of carrying capacity is calculated from theoretical formula and load test results. The design resistance may be calculated using conventional static pile design theory. The pile founding depths should be predetermined before installation from a site geotechnical investigation. To ascertain the field performance and estimate load carrying capacities of piles, in-situ pile load tests should be conducted. In this study, field pile load test data is analyzed to estimate the ultimate load for end bearing piles. The investigated site is about 100 × 110 m located in Alexandria, Egypt. Geotechnical investigations at the site are carried out to a maximum depth of 45 m. Four borings have been done in field. The tests are conducted at the site for two skelton structure buildings to be constructed on raft foundation rested on piles executed by continuous flight auger. Four pile load tests are performed on 600 mmdiameters and 27 mlengths. Ultimate capacities of piles are determined according to different methods. It is concluded that the percentage of friction load carried by the shaft along the pile length is about 46% of total load while the percentage of load carried by the end bearing is 54% of total load. A new proposed method by the author is presented to calculate the ultimate capacity of pile from pile load test. The proposed method depends on the settlement of pile without taken into consideration the elastic deformation. An empirical formula is presented from the relationship between stress and settlement of pile due to friction and end bearing only after deducting the elastic deformation. However, the obtained results for the ultimate capacity of end bearing piles are considered to be more accurate than other methods. The proposed method appears to give bitter results that agrees well with the theoretical predictions. The proposed method is easier, quicker and more reliable.

Grouted Pile and Its Bearing Capacity

The grouting method applied in bored pile is an improvement to the conventional bored pile. Load tests have proved that grouting under the bored pile tip is an effective method to enhance the bearing capacity of the pile and to reduce the pile settlement. In this paper, the grouting technology is described and pile load test results are discussed. In order to put the grouting method into design practice, the authors analyze the working mechanism of soil compaction. And, based on the theory of cavities expansion in soil mass, approximate formulae are proposed for estimating the bearing capacity of the grouted pile. The theoretical prediction agrees well with the load test results.