The relationships between the microstructure, the composition, the friction temperature and the form of a new kind of friction material which is a glass fibre resin friction materials (GFRF) are studied through a seri...The relationships between the microstructure, the composition, the friction temperature and the form of a new kind of friction material which is a glass fibre resin friction materials (GFRF) are studied through a series of tests on machine as EPMA, STM, DTG-DTA,an optical microscope and a friction test machine. The tests show that the rising rate in temperature and the heat conductivity of GFRF are lower than that of asbestos friction material. In GFRF, the heat-decline is slowed down or even eliminated. the distribution of heat- stress is improved and the life span is extended. Raising the temperature of resin resolution and enhancing the stickness between resin and glass fibre are the two important procedures to improve the friction and wear performance of GFRF.A discription about the friction and wear mechanism of GFRF is given in this paper.展开更多
Titanium has been increasingly applied to biomedical application because of its improved mechanical characteristics, corrosion resistance and biocompatibility. However their application remains limited, due to the low...Titanium has been increasingly applied to biomedical application because of its improved mechanical characteristics, corrosion resistance and biocompatibility. However their application remains limited, due to the low strength and poor wear resistance of unalloyed titanium. The purpose of this study is to evaluate the friction and wear behavior of high-strength titanium alloys: Ti-6Al-7Nb used in femoral stem (total hip prosthesis). The oscillating friction and wear tests have been carried out in ambient air with oscillating tribotester in accord with standards ISO 7148, ASTM G99-95a, ASTM G 133-95 under different conditions of normal applied load (3, 6 and 10 N) and sliding speed (1, 15 and 25 mm.s-1), and as a counter pair we used the ball of 100C 6, 10 mm of diameter. The surface morphology of the titanium alloys has been characterized by SEM, EDAX, micro hardness, roughness analysis measurements. The behavior observed for both samples suggests that the wear and friction mechanism during the test is the same for Ti alloys, and to increase resistance to wear and friction of biomedical titanium alloys used in total hip prosthesis (femoral stems) the surface coating and treatment are required.展开更多
To simulate the wear and corrosion behavior of high-strength EH47 hull steel in a complicated marine environment in which seawater,sea ice,and sea sand coexist,accelerated wear and corrosion tests were performed in a ...To simulate the wear and corrosion behavior of high-strength EH47 hull steel in a complicated marine environment in which seawater,sea ice,and sea sand coexist,accelerated wear and corrosion tests were performed in a laboratory setting using a tribometer.The effect of large loads on the behavior of abrasion and corrosion in a 3.5wt%NaCl solution with ice and sand to simulate a marine environment were investigated.The experimental results showed that the coefficient of friction(COF)decreases with increasing working load;meanwhile,the loading force and sand on the disk strongly influence the COF.The mechanisms of friction and the coupling effect of abrasion and corrosion in the 3.5wt%NaCl solution with sand were the wear and corrosion mechanisms;furthermore,the wear mechanism exerted the predominant effect.展开更多
The use of asbestos material is being avoided to manufacture the brake pads as it is harmful and toxic in nature. Further it leads to various health issues like asbestosis, mesothelioma and lung cancers. These brake p...The use of asbestos material is being avoided to manufacture the brake pads as it is harmful and toxic in nature. Further it leads to various health issues like asbestosis, mesothelioma and lung cancers. These brake pads can be replaced by natural fibers like Palm kernel (0-50%), Nile roses (0-15%) and Wheat (0-10%) with additives like aluminum oxide (5%-20%) and graphite powder (10%-35%). Phenolic resin of 35% is utilized as a binder. Particulated Nile roses are used to increase the friction coefficient and wheat powder is used to reduce the wear rate. Aluminum oxide and graphite are abrasive in nature. This helps to make brake pads with high friction co-efficient and less wear rate with low noise pollution. The wear of the proposed composites have been investigated at different speeds. Various tests like wear on pin-ondisc apparatus, hardness on the Rockwell hardness apparatus and oil absorption test have been conducted. Phenolic resin produces good bonding nature to fiber. Thus, Fibers found to have performed palatably among all commercial brake pads. The objective of the research indicates that Palm kernal shell could be a conceivable alternative for asbestos in friction coating materials.展开更多
With the development of green tribology in the shipping industry,the application of water lubrication gradually replaces oil lubrication in stern bearings and thrust bearings.In terms of large-scale and high-speed shi...With the development of green tribology in the shipping industry,the application of water lubrication gradually replaces oil lubrication in stern bearings and thrust bearings.In terms of large-scale and high-speed ships,water-lubricated bearings with high performance are more strictly required.However,due to the lubricating medium,water-lubricated bearings have many problems such as friction,wear,vibration,noise,etc.This review focuses on the performance of marine water-lubricated bearings and their failure prevention mechanism.Furthermore,the research of marine water-lubricated bearings is reviewed by discussing its lubrication principle,test technology,friction and wear mechanism,and friction noise generation mechanism.The performance enhancement methods have been overviewed from structure optimization and material modification.Finally,the potential problems and the perspective of water-lubricated bearings are given in detail.展开更多
文摘The relationships between the microstructure, the composition, the friction temperature and the form of a new kind of friction material which is a glass fibre resin friction materials (GFRF) are studied through a series of tests on machine as EPMA, STM, DTG-DTA,an optical microscope and a friction test machine. The tests show that the rising rate in temperature and the heat conductivity of GFRF are lower than that of asbestos friction material. In GFRF, the heat-decline is slowed down or even eliminated. the distribution of heat- stress is improved and the life span is extended. Raising the temperature of resin resolution and enhancing the stickness between resin and glass fibre are the two important procedures to improve the friction and wear performance of GFRF.A discription about the friction and wear mechanism of GFRF is given in this paper.
文摘Titanium has been increasingly applied to biomedical application because of its improved mechanical characteristics, corrosion resistance and biocompatibility. However their application remains limited, due to the low strength and poor wear resistance of unalloyed titanium. The purpose of this study is to evaluate the friction and wear behavior of high-strength titanium alloys: Ti-6Al-7Nb used in femoral stem (total hip prosthesis). The oscillating friction and wear tests have been carried out in ambient air with oscillating tribotester in accord with standards ISO 7148, ASTM G99-95a, ASTM G 133-95 under different conditions of normal applied load (3, 6 and 10 N) and sliding speed (1, 15 and 25 mm.s-1), and as a counter pair we used the ball of 100C 6, 10 mm of diameter. The surface morphology of the titanium alloys has been characterized by SEM, EDAX, micro hardness, roughness analysis measurements. The behavior observed for both samples suggests that the wear and friction mechanism during the test is the same for Ti alloys, and to increase resistance to wear and friction of biomedical titanium alloys used in total hip prosthesis (femoral stems) the surface coating and treatment are required.
基金This work was financially supported by the National Natural Science Foundation of China(Nos.51474127 and 51671100)the State Key Laboratory of Metal Material for Marine Equipment and Application-University of Science and Technology Liaoning co-project,China(Nos.SKLMEA-USTL 2017010 and 201905).
文摘To simulate the wear and corrosion behavior of high-strength EH47 hull steel in a complicated marine environment in which seawater,sea ice,and sea sand coexist,accelerated wear and corrosion tests were performed in a laboratory setting using a tribometer.The effect of large loads on the behavior of abrasion and corrosion in a 3.5wt%NaCl solution with ice and sand to simulate a marine environment were investigated.The experimental results showed that the coefficient of friction(COF)decreases with increasing working load;meanwhile,the loading force and sand on the disk strongly influence the COF.The mechanisms of friction and the coupling effect of abrasion and corrosion in the 3.5wt%NaCl solution with sand were the wear and corrosion mechanisms;furthermore,the wear mechanism exerted the predominant effect.
文摘The use of asbestos material is being avoided to manufacture the brake pads as it is harmful and toxic in nature. Further it leads to various health issues like asbestosis, mesothelioma and lung cancers. These brake pads can be replaced by natural fibers like Palm kernel (0-50%), Nile roses (0-15%) and Wheat (0-10%) with additives like aluminum oxide (5%-20%) and graphite powder (10%-35%). Phenolic resin of 35% is utilized as a binder. Particulated Nile roses are used to increase the friction coefficient and wheat powder is used to reduce the wear rate. Aluminum oxide and graphite are abrasive in nature. This helps to make brake pads with high friction co-efficient and less wear rate with low noise pollution. The wear of the proposed composites have been investigated at different speeds. Various tests like wear on pin-ondisc apparatus, hardness on the Rockwell hardness apparatus and oil absorption test have been conducted. Phenolic resin produces good bonding nature to fiber. Thus, Fibers found to have performed palatably among all commercial brake pads. The objective of the research indicates that Palm kernal shell could be a conceivable alternative for asbestos in friction coating materials.
基金financially supported by the National Key R&D Program of China(No.2018YFE0197600)National Natural Science Foundation of China(No.52071244).
文摘With the development of green tribology in the shipping industry,the application of water lubrication gradually replaces oil lubrication in stern bearings and thrust bearings.In terms of large-scale and high-speed ships,water-lubricated bearings with high performance are more strictly required.However,due to the lubricating medium,water-lubricated bearings have many problems such as friction,wear,vibration,noise,etc.This review focuses on the performance of marine water-lubricated bearings and their failure prevention mechanism.Furthermore,the research of marine water-lubricated bearings is reviewed by discussing its lubrication principle,test technology,friction and wear mechanism,and friction noise generation mechanism.The performance enhancement methods have been overviewed from structure optimization and material modification.Finally,the potential problems and the perspective of water-lubricated bearings are given in detail.
