The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct ...The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct virtual elements and stress servo control to approximately replace the hydraulic support problem,this paper establishes a new numerical model of hydraulic support with the same working characteristics as the actual hydraulic support by integrating numerical simulation software Rhino,Griddle and FLAC3D,which can realize the simulation of different working conditions.Based on this model,the influence mechanism of the supporting strength of hydraulic support on surrounding rock stress regulation and coal stability in front of the top coal caving face in extra thick coal seam were researched.Firstly,under different support intensity,the abutment pressure of the bearing coal and the coal in front of it presents the “three-stage”evolution characteristics.The influence range of support intensity is 15%–30%.Secondly,1.5 MPa is the upper limit of impact that the support strength can have on the front coal failure area.Thirdly,within a displacement range of 2.76 m from the coal wall,a support strength of1.5 MPa provides optimal control of the horizontal displacement of the coal.展开更多
The deformation and fracture evolution mechanisms of the strata overlying mines mined using sublevel caving were studied via numerical simulations.Moreover,an expression for the normal force acting on the side face of...The deformation and fracture evolution mechanisms of the strata overlying mines mined using sublevel caving were studied via numerical simulations.Moreover,an expression for the normal force acting on the side face of a steeply dipping superimposed cantilever beam in the surrounding rock was deduced based on limit equilibrium theory.The results show the following:(1)surface displacement above metal mines with steeply dipping discontinuities shows significant step characteristics,and(2)the behavior of the strata as they fail exhibits superimposition characteristics.Generally,failure first occurs in certain superimposed strata slightly far from the goaf.Subsequently,with the constant downward excavation of the orebody,the superimposed strata become damaged both upwards away from and downwards toward the goaf.This process continues until the deep part of the steeply dipping superimposed strata forms a large-scale deep fracture plane that connects with the goaf.The deep fracture plane generally makes an angle of 12°-20°with the normal to the steeply dipping discontinuities.The effect of the constant outward transfer of strata movement due to the constant outward failure of the superimposed strata in the metal mines with steeply dipping discontinuities causes the scope of the strata movement in these mines to be larger than expected.The strata in the metal mines with steeply dipping discontinuities mainly show flexural toppling failure.However,the steeply dipping structural strata near the goaf mainly exhibit shear slipping failure,in which case the mechanical model used to describe them can be simplified by treating them as steeply dipping superimposed cantilever beams.By taking the steeply dipping superimposed cantilever beam that first experiences failure as the key stratum,the failure scope of the strata(and criteria for the stability of metal mines with steeply dipping discontinuities mined using sublevel caving)can be obtained via iterative computations from the key stratum,moving downward toward and upwards away from the goaf.展开更多
In order to comprehend the dynamic disaster mechanism induced by overburden rock caving during the advancement of a coal mining face, a physical simulation model is constructed basing on the geological condition of th...In order to comprehend the dynamic disaster mechanism induced by overburden rock caving during the advancement of a coal mining face, a physical simulation model is constructed basing on the geological condition of the 21221 mining face at Qianqiu coal mine in Henan Province, China. This study established, a comprehensive monitoring system to investigate the interrelations and evolutionary characteristics among multiple mechanical parameters, including mining-induced stress, displacement, temperature, and acoustic emission events during overburden rock caving. It is suggested that, despite the uniformity of the overburden rock caving interval, the main characteristic of overburden rock lies in its uneven caving strength. The mining-induced stress exhibits a reasonable interrelation with the displacement, temperature, and acoustic emission events of the rock strata. With the advancement of the coal seam, the mining-induced stress undergoes four successive stages: gentle stability, gradual accumulation, high-level mutation, and a return to stability. The variations in other mechanical parameters does not synchronize with the signifcant changes in mining-induced stress. Before the collapse of overburden rock occurs, rock strata temperature increment decreases and the acoustic emission ringing counts surges with the increase of rock strata displacement and mining-induced stress. Therefore, the collaborative characteristics of mining-induced stress, displacement, temperature, and acoustic emission ringing counts can be identifed as the precursor information or overburden rock caving. These results are in good consistent with on-site situation in the coal mine.展开更多
Hanging roofs or high hang-ups.a common problem in sublevel caving mining,usually result in a large ore loss and undermine mining safety.This paper analyzed the formation of a hanging roof and showed that increased co...Hanging roofs or high hang-ups.a common problem in sublevel caving mining,usually result in a large ore loss and undermine mining safety.This paper analyzed the formation of a hanging roof and showed that increased confining pressure and reduced free surface were its main characteristics.In order to break down a hanging roof,a new method based on shock wave collision and stress superposition was developed.In this method,two blastholes containing multi-primer at different positions are simultaneously initiated at first.By doing this,a new free surface and a swell room can be created.After these holes are fired,a long delay time is given to the next blasthole so that the fragments from the first twohole blasting have enough time to fall down.This new method was applied to three hanging roofs in one production area,and all of them were successfully broken down.Field inspection indicated that almost no damage was caused in the nearby drifts/tunnels due to the new method.In addition,the far field vibrations were found to be smaller than the maximum vibrations induced by some other blasts.展开更多
Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving(LTCC) mining technology is studied by using self-developed three-dimensional(3D) test device. The loose top-c...Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving(LTCC) mining technology is studied by using self-developed three-dimensional(3D) test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.展开更多
It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal...It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.展开更多
Understanding the characteristics of drawing body shape is essential for optimization of drawing parameters in longwall top coal caving mining.In this study,both physical experiments and theoretical analysis are emplo...Understanding the characteristics of drawing body shape is essential for optimization of drawing parameters in longwall top coal caving mining.In this study,both physical experiments and theoretical analysis are employed to investigate these characteristics and derive a theoretical equation for the drawing body shape along the working face in an inclined seam.By analyzing the initial positions of drawn marked particles,the characteristics of the drawing body shape for different seam dip angles are obtained.It is shown that the drawing body of the top coal exhibits a shape-difference and volume-symmetry characteristic,on taking a vertical line through the center of support opening as the axis of symmetry,the shapes of the drawing body on the two sides of this axis are clearly different,but their volumes are equal.By establishing theoretical models of the drawing body in the initial drawing stage and the normal drawing stage,a theoretical equation for the drawing body in an inclined seam is proposed,which can accurately describe the characteristics of the drawing body shape.The shape characteristics and volume symmetry of the drawing body are further analyzed by comparing the results of theoretical calculations and numerical simulations.It is shown that one side of the drawing body is divided into two parts by an inflection point,with the lower part being a variation development area.This variation development area increases gradually with increasing seam dip angle,resulting in an asymmetry of the drawing body shape.However,the volume symmetry coefficient fluctuates around 1 for all values of the seam dip angle variation,and the volumes of the drawing body on the two sides are more or less equal as the variation development volume is more or less equal to the cut volume.Both theoretical calculations and numerical simulations confirm that the drawing body of the top coal exhibits the shape-difference and volume-symmetry characteristic.展开更多
During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was establish...During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was established to determine the relationship between the location of the stope roof and the caving surface,enabling the mathematical computation of the top caving angle(φ).The drilling method was employed to measure the top caving angle on two extra-thick fully mechanized coal caving faces under the conditions of three geological structures,namely,no geological structure,igneous rock structure,and fault structure.The results show that the value of top caving angle could be accurately estimated on-site with the 9-parameter 3D top coal caving surface model built with the drilling method.This method is a novel on-site measurement that can be easily applied.Our findings reveal that the characteristics of the coal-rock in the two mining faces are different;yet their caving angles follow the ruleφ_(igneous rock structure)<φ_(no geological structure)<φ_(fault structure).Finally,through the data fitting with two indexes(the top coal uniaxial compressive strength and the top caving angle),it is found that the relationship between the two indexes satisfies an exponential decay function.展开更多
The stability control of gob-side entry retaining in fully mechanized caving face is a typical challenge in many coal mines in China.The rotation and subsidence of the lateral cantilever play a critical role in a coal...The stability control of gob-side entry retaining in fully mechanized caving face is a typical challenge in many coal mines in China.The rotation and subsidence of the lateral cantilever play a critical role in a coal mine,possibly leading to instability in a coal seam wall or a gob-side wall due to its excessive rotation subsidence.Hence,the presplitting blasting measures in the roof was implemented to cut down the lower main roof and convert it to caved immediate roof strata,which can significantly reduce the rotation space for the lateral cantilever and effectively control its rotation.Firstly,the compatible deformation model was established to investigate the quantitative relationship between the deformation of the coal seam wall and the gob-side wall and the subsidence of the lateral cantilever.Then,the instability judgments for the coal seam wall and gob-side wall were revealed,and the determination method for the optimal roof cutting height were obtained.Furthermore,The Universal Distinct Element Code numerical simulation was adopted to investigate the effect of roof-cutting height on the stability of the retained entry.The numerical simulation results indicated that the deformation of the roadway could be effectively controlled when the roofcutting height reached to 18 m,which verified the theoretical deduction well.Finally,a field application was performed at the No.3307 haulage gateway in the Tangan coal mine,Ltd.,Shanxi Province,China.The field monitoring results showed that the blasting roof cutting method could effectively control the large deformation of surrounding rocks,which provided helpful references for coal mine safety production under similar conditions.展开更多
Effective control of roof strata is very important for trouble free operation and regular face advance in mechanised longwall workings. It is now technically possible to exploit coal seams in difficult geomining condi...Effective control of roof strata is very important for trouble free operation and regular face advance in mechanised longwall workings. It is now technically possible to exploit coal seams in difficult geomining conditions with the help of newer innovations in longwall face machineries. A reliable assessment of caving behaviour and support capacity requirement helps in selecting supports of adequate capacity and making operational preparedness for timely and confident solution of impending problems.This paper reviews the mechanism of roof caving and the conventional approaches of caving behaviour and support requirement in the context of major strata control experiences gained worldwide. The review shows that a number of approaches are being used for advance prediction of caving behaviour and support capacity requirement in a variety of geo-mining conditions. The theoretical explanation of the mechanism of roof caving and the design function of roof supports have been worked out through staged development of approaches, their evaluation followed by their gradual modification and enrichment of synthesized findings. This process is still continuing with consistently improved understanding through growing field experiences in the larger domain of geo-mining conditions and state-of-art strata analysis and monitoring techniques. These attempts have contributed significantly to improving the level of understanding and reducing the gap of uncertainty in planning and design of longwall operation in a given geo-mining condition.展开更多
This review details the state of the art in research on top coal drawing mechanisms in Longwall top coal caving(LTCC)by examining the relevant literature over the last two decades.It startswith an introduction of the ...This review details the state of the art in research on top coal drawing mechanisms in Longwall top coal caving(LTCC)by examining the relevant literature over the last two decades.It startswith an introduction of the brief history and basic procedures of LTCC.The framework of research on the drawing mechanism,basic concepts,and some theoretical models of LTCC are detailed in sect.research framework of top coal drawingmechanism.The authors note that theTop coal drawbody(TCD),Top coal boundary(TCB)and Top coal recovery ratio(TCRR)are key factors in the drawingmechanism.TheBody-boundary-ratio(BBR)research system has been the classic framework for research over the last 20 years.The modified Bergmark-Roos model,which considers the effects of the supporting rear canopy,flowing velocity of top coal,and its shape factor,is optimal for characterizing the TCD.A 3Dmodel to describe the TCB that considers the thicknesses of the coal seam and roof strata is reviewed.In sect.physical testing and numerical simulation,the physical tests and numerical simulations in the literature are classified for ease of bibliographical review,and classic conclusions regarding the drawing mechanism of top coal are presented and discussedwith elaborate illustrations and descriptions.The deflection of the TCDis noted,and is caused by the shape of the rear canopy.The inclined coal seam always induces a largerTCD,and a deflection in theTCDhas also been observed in it.The effects of the drawing sequence and drawing interval on the TCRR are reviewed,where a long drawing interval is found to lead to significant loss of top coal.Its flowing behavior and velocity distribution are also presented.Sect.practical applications of drawingmechanisms forLTCCmines 4 summarizes over 10 cases where the TCRRof LTCCmines improved due to the guidance of the drawing mechanism.The final section provides a summary of the work here and some open questions.Prospective investigations are highlighted to give researchers guidance on promising issues in future research on LTCC.展开更多
The size distribution of the broken top coal blocks is an important factor,affecting the recovery ratio and the efficiency of drawing top coal in longwall top coal caving(LTCC)mining panel.The standard deviation of to...The size distribution of the broken top coal blocks is an important factor,affecting the recovery ratio and the efficiency of drawing top coal in longwall top coal caving(LTCC)mining panel.The standard deviation of top coal block size(dt)is one of the main parameters to reflect the size distribution of top coal.To find the effect of dt on the caving mechanism,this study simulates experiments with 9 different dt by using discrete element software PFC.The dt is divided into two stages:uniform distribution stage(UDS)whose dt is less than 0.1(Schemes 1–5),and nonuniform distribution stage(NDS)whose dt is more than 0.1(Schemes 6–9).This research mainly investigates the variation of recovery ratio,drawing body shape,boundary of top coal,and contact force between particles in the two stages,respectively.The results showed that with the increasing dt,the recovery ratio of the panel increases first and then decreases in UDS.It is the largest in Scheme 3,which mainly increases the drawing volume at the side of starting drawing end.However,the recovery ratio decreases first and then increases quickly in NDS,and it is the largest in Scheme 9,where the drawing volume at the side of finishing drawing end are relatively higher.In UDS,the major size of top coal is basically medium,while in NDS,the size varies from medium to small,and then to large,with a distinct difference in shape and volume of the drawing body.When the major size of top coal is medium and small,the cross-section width of the initial boundary of top coal at each height is relatively small.Conversely,when the top coal size is large,the initial boundary of top coal has a larger opening range,the rotating angle of lower boundary is relatively small in the normal drawing stage,which is conducive to the development of drawing body and reduces the residual top coal,and the maximum particle velocity and the particles movement angle are both larger.This study lays a foundation for the prediction of recovery ratio,and suggests that the uniform top coal is more manageable and has a larger recovery ratio.展开更多
In order to realize the modernized miningmanagementi the authors. based on the practice of a specified mine, developed the application software of the broken ore drawing data management system for sublevel caving thro...In order to realize the modernized miningmanagementi the authors. based on the practice of a specified mine, developed the application software of the broken ore drawing data management system for sublevel caving through the study on FOXBASE computer language. This paper elabo-rates the overall conception of this system , indicates the main task which should he completed in this system and introduces its module structure and main functions.展开更多
Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-c...Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.展开更多
This paper analyzes the gas source of the horizontally sectioned fully mechanized caving face in the steeply inclined and extra-thick seam of Adaohai Coal Mine, and numerically simulates the stress distribution and pr...This paper analyzes the gas source of the horizontally sectioned fully mechanized caving face in the steeply inclined and extra-thick seam of Adaohai Coal Mine, and numerically simulates the stress distribution and pressure relief of the lower section coal after the upper section working face is mined. It theoretically analyzed the reasonable layout of the drainage boreholes, and designed the drainage borehole layout accordingly. In the upper and lower section of the working face, the actual drainage effect of the boreholes was inspected, and the air exhaust gas volume in the working face was statistically analyzed. It was confirmed that the layout of boreholes was reasonable, the gas control effect of working face was greatly improved and fully met the needs of safe mining. The control effect was greatly improved and the need for safe mining was fully met, and thus a gas drainage technology suitable for the coal seam storage conditions and mining technology of the Adaohai Coal Mine was found. That is to say: the gas emission from the working face of the section mining mainly comes from its lower coal body. Pre-draining the lower coal body of the section and depressurizing gas interception and drainage are the key to effectively solve the problem of gas emission from the working face. Drainage boreholes in the working face of the section should be arranged at high and low positions. The high-level boreholes are located about 2 m from the top of the working face, and the high-level boreholes are about 9 m away from the top of the working face. Through the pre drainage of high and low-level boreholes in advance and the interception and pressure relief drainage, the gas control in the horizontal sublevel fully mechanized caving mining face in steep and extra thick coal seam can realize a virtuous cycle.展开更多
Longwall Top Coal Caving has been considered as one of the most effective technologies for the extraction of underground thick coal seams. A large number of studies on the applicability of Longwall Top Coal Caving int...Longwall Top Coal Caving has been considered as one of the most effective technologies for the extraction of underground thick coal seams. A large number of studies on the applicability of Longwall Top Coal Caving into new mine sites have linked the success of its application to the geo mechanical understanding of the cavability of the top coal. The paper aims to improve the knowledge of the top coal cavability evaluation. A range of parameters that affect the top coal cavability were first identified. Afterward, a number of cavability assessment methods and classifications were reviewed. The result is important in that it assists researchers in developing an advanced and reliable tool for the top coal cavability evaluation.展开更多
Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole...Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole photography technique and the seismic CT scanner technique, the deformation and failure of overlying strata of fully mechanized caving face in shallow coal seam were studied and the failure development of overburden was determined. Results show that the full view borehole photography can reveal the characteristics of strata, and the seismic CT scanner can reflect the characteristics of strata between the boreholes. The combined measurement technique can effectively determine the height of fractured and caved zones. The top end of the caved zone in Yangwangou coal mine employing the top coal caving longwall mining was at the depth of 171 m and fractured zone was at the depth of 106-110 m. The results provide a theoretic foundation for controlling the overburden strata in the shallow buried top coal caving panel.展开更多
AS a foreigner anywhere, it is important to make an effort to experience the cultural heritage of the city you are in. In Paris you should visit Montmartre, in London you can't miss Buckingham Palace, and before you ...AS a foreigner anywhere, it is important to make an effort to experience the cultural heritage of the city you are in. In Paris you should visit Montmartre, in London you can't miss Buckingham Palace, and before you leave Sydney, a trip to the Blue Mountains is essential, For Beiiing, the unquestionable birthplace of Chinese culture is buried deep within the city's ancient hutongs.展开更多
With a history of more than 100 years, Chuquicamata has become one of the largest open pits in the world. Its current depth of 1100 m, length of 4500 m and width of 3000 m, resulting in haulage distances of over 11,00...With a history of more than 100 years, Chuquicamata has become one of the largest open pits in the world. Its current depth of 1100 m, length of 4500 m and width of 3000 m, resulting in haulage distances of over 11,000 m from pit bottom to the processing plant or waste dumps, with waste/ore ratio greater than 4 and much lower grades, are effectively determining its profitable limit by the end of this decade. Currently, there are over 4300 Mt of geological resources containing 0.7% of copper and 340 ppm (1 ppm = 1 g/t) of molybdenum below the final pit shell. The corresponding orebody geometry is 3000 m northsouth, 300-800 m eastwest and the drilling campaign suggested the existence of more than 900 m of mineable ore from the final pit bottom. This is in spite of the fact that the Chuquicamata orebody is still open at depth. The business case to continue with the mining of the Chuquicamata orebody is to change from the current large open pit to a novel macroblock variant block caving geometry. This requires a production rate of 140,000 t/d (50 Mt per annum), with a continuous material handling system to achieve the 7-year ramp-up to full production. The resolution of a number of known technical, operational and logistical challenges outside current industry practises which Chuquicamata will face over its projected 40-year mine life is therefore essential. These challenges include simultaneous operations of open pit and underground macroblocks and from the initial lift to the second lift, rapid ramp-up and optimum sequencing of the planned macroblocks, early dilution from the west fault and late dilution from potential slope failures, and the potential for major operational hazards. An equally important issue to be addressed is cultural given that the mining history in the northern region of Chile, which includes Chuquicamata, is predominantly open pit. This paper presents a synopsis of the main challenges that the Chuquicamata underground project will face in order to meet the objectives of its corresponding business case. Those discussed and how they were resolved are: simultaneous operations, rapid ramp-up and optimum sequencing of the planned macroblocks, and early and late dilutions. The project is an example of the fact that there are no recipes or cook books in cave mining.展开更多
New method for handling roof of the base successive mining is proposed, which is induction caving in the roof. The key is that it is made certain to the station of the space-time in the induction caving roof, as the s...New method for handling roof of the base successive mining is proposed, which is induction caving in the roof. The key is that it is made certain to the station of the space-time in the induction caving roof, as the stress is released with the mining process. And applying the catastrophe theory, the influencing factors of induction caving roof are studied in the emptied areas, such as the mechanical property of the surrounding rock, the area of the gob,the scope and dimension of tensile stress. The results show that the key factor is the area of the gob to the method of the induction caving roof. Then according to the geology and the ore characteristic, the three dimension FEM mechanical model is built in Tongkeng Mine, the laws of the tensile stress are analyzed to the space and the time in the roof with the mining, then it is rational design to the mine step and time of the handing the roof.展开更多
基金supported by Distinguished Youth Funds of National Natural Science Foundation of China (No.51925402)National Natural Science Foundation of China (Nos.51904203 and 52174125)+4 种基金the China Postdoctoral Science Foundation (No.2021M702049)the Tencent Foundation or XPLORER PRIZEShanxi Science and Technology Major Project Funds (No.20201102004)Shanxi-Zheda Institute of Advanced Materials and Chemical Engineering (No.2021SX-TD001)Open Fund Research Project Supported by State Key Laboratory of Strata Intelligent Control and Green Mining Co-founded by Shandong Province and the Ministry of Science and Technology (No.SICGM202209)。
文摘The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct virtual elements and stress servo control to approximately replace the hydraulic support problem,this paper establishes a new numerical model of hydraulic support with the same working characteristics as the actual hydraulic support by integrating numerical simulation software Rhino,Griddle and FLAC3D,which can realize the simulation of different working conditions.Based on this model,the influence mechanism of the supporting strength of hydraulic support on surrounding rock stress regulation and coal stability in front of the top coal caving face in extra thick coal seam were researched.Firstly,under different support intensity,the abutment pressure of the bearing coal and the coal in front of it presents the “three-stage”evolution characteristics.The influence range of support intensity is 15%–30%.Secondly,1.5 MPa is the upper limit of impact that the support strength can have on the front coal failure area.Thirdly,within a displacement range of 2.76 m from the coal wall,a support strength of1.5 MPa provides optimal control of the horizontal displacement of the coal.
基金Financial support for this work was provided by the Youth Fund Program of the National Natural Science Foundation of China (No. 42002292)the General Program of the National Natural Science Foundation of China (No. 42377175)the General Program of the Hubei Provincial Natural Science Foundation, China (No. 2023AFB631)
文摘The deformation and fracture evolution mechanisms of the strata overlying mines mined using sublevel caving were studied via numerical simulations.Moreover,an expression for the normal force acting on the side face of a steeply dipping superimposed cantilever beam in the surrounding rock was deduced based on limit equilibrium theory.The results show the following:(1)surface displacement above metal mines with steeply dipping discontinuities shows significant step characteristics,and(2)the behavior of the strata as they fail exhibits superimposition characteristics.Generally,failure first occurs in certain superimposed strata slightly far from the goaf.Subsequently,with the constant downward excavation of the orebody,the superimposed strata become damaged both upwards away from and downwards toward the goaf.This process continues until the deep part of the steeply dipping superimposed strata forms a large-scale deep fracture plane that connects with the goaf.The deep fracture plane generally makes an angle of 12°-20°with the normal to the steeply dipping discontinuities.The effect of the constant outward transfer of strata movement due to the constant outward failure of the superimposed strata in the metal mines with steeply dipping discontinuities causes the scope of the strata movement in these mines to be larger than expected.The strata in the metal mines with steeply dipping discontinuities mainly show flexural toppling failure.However,the steeply dipping structural strata near the goaf mainly exhibit shear slipping failure,in which case the mechanical model used to describe them can be simplified by treating them as steeply dipping superimposed cantilever beams.By taking the steeply dipping superimposed cantilever beam that first experiences failure as the key stratum,the failure scope of the strata(and criteria for the stability of metal mines with steeply dipping discontinuities mined using sublevel caving)can be obtained via iterative computations from the key stratum,moving downward toward and upwards away from the goaf.
基金supported by the State Key Research Development Program of China(2022YFC3004602)Independent Research fund of Joint NationalLocal Engineering Research Centre for Safe and Precise Coal Mining(Anhui University of Science and Technology)(EC2022001)+2 种基金the National Natural Science Foundation of China(41872205)Beijing Natural Science Foundation(8202041)the Fundamental Research Funds for the Central Universities(2022YJSLJ08,2022JCCXNY03).
文摘In order to comprehend the dynamic disaster mechanism induced by overburden rock caving during the advancement of a coal mining face, a physical simulation model is constructed basing on the geological condition of the 21221 mining face at Qianqiu coal mine in Henan Province, China. This study established, a comprehensive monitoring system to investigate the interrelations and evolutionary characteristics among multiple mechanical parameters, including mining-induced stress, displacement, temperature, and acoustic emission events during overburden rock caving. It is suggested that, despite the uniformity of the overburden rock caving interval, the main characteristic of overburden rock lies in its uneven caving strength. The mining-induced stress exhibits a reasonable interrelation with the displacement, temperature, and acoustic emission events of the rock strata. With the advancement of the coal seam, the mining-induced stress undergoes four successive stages: gentle stability, gradual accumulation, high-level mutation, and a return to stability. The variations in other mechanical parameters does not synchronize with the signifcant changes in mining-induced stress. Before the collapse of overburden rock occurs, rock strata temperature increment decreases and the acoustic emission ringing counts surges with the increase of rock strata displacement and mining-induced stress. Therefore, the collaborative characteristics of mining-induced stress, displacement, temperature, and acoustic emission ringing counts can be identifed as the precursor information or overburden rock caving. These results are in good consistent with on-site situation in the coal mine.
文摘Hanging roofs or high hang-ups.a common problem in sublevel caving mining,usually result in a large ore loss and undermine mining safety.This paper analyzed the formation of a hanging roof and showed that increased confining pressure and reduced free surface were its main characteristics.In order to break down a hanging roof,a new method based on shock wave collision and stress superposition was developed.In this method,two blastholes containing multi-primer at different positions are simultaneously initiated at first.By doing this,a new free surface and a swell room can be created.After these holes are fired,a long delay time is given to the next blasthole so that the fragments from the first twohole blasting have enough time to fall down.This new method was applied to three hanging roofs in one production area,and all of them were successfully broken down.Field inspection indicated that almost no damage was caused in the nearby drifts/tunnels due to the new method.In addition,the far field vibrations were found to be smaller than the maximum vibrations induced by some other blasts.
基金financially supported by the Coal Joint Funds of the National Natural Science Foundation of China(No.U1361209)the National Basic Research Program of China(973 Program)(No.2013CB227903)
文摘Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving(LTCC) mining technology is studied by using self-developed three-dimensional(3D) test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.
基金sponsored by the National Natural Science Foundation of China(No.51374092)
文摘It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.
基金The authors gratefully acknowledge financial support from the Natural Science Foundation of China(51674264.51574244)the National Key R&D Plan of China(2018YFC0604501)+1 种基金the China Postdoctoral Science Foundation(2018M631622)Special acknowledgements are also given to the China Scholarship Council(CSC).
文摘Understanding the characteristics of drawing body shape is essential for optimization of drawing parameters in longwall top coal caving mining.In this study,both physical experiments and theoretical analysis are employed to investigate these characteristics and derive a theoretical equation for the drawing body shape along the working face in an inclined seam.By analyzing the initial positions of drawn marked particles,the characteristics of the drawing body shape for different seam dip angles are obtained.It is shown that the drawing body of the top coal exhibits a shape-difference and volume-symmetry characteristic,on taking a vertical line through the center of support opening as the axis of symmetry,the shapes of the drawing body on the two sides of this axis are clearly different,but their volumes are equal.By establishing theoretical models of the drawing body in the initial drawing stage and the normal drawing stage,a theoretical equation for the drawing body in an inclined seam is proposed,which can accurately describe the characteristics of the drawing body shape.The shape characteristics and volume symmetry of the drawing body are further analyzed by comparing the results of theoretical calculations and numerical simulations.It is shown that one side of the drawing body is divided into two parts by an inflection point,with the lower part being a variation development area.This variation development area increases gradually with increasing seam dip angle,resulting in an asymmetry of the drawing body shape.However,the volume symmetry coefficient fluctuates around 1 for all values of the seam dip angle variation,and the volumes of the drawing body on the two sides are more or less equal as the variation development volume is more or less equal to the cut volume.Both theoretical calculations and numerical simulations confirm that the drawing body of the top coal exhibits the shape-difference and volume-symmetry characteristic.
基金This work was supported by the Science and Technology Innovation Project of Higher Education in Shanxi Province(No.2019L0754)Central Guiding Local Science and Technology Development Fund project(No.YDZJSX2021B021)the Datong Science and Technology Plan Project(No.2019122).
文摘During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was established to determine the relationship between the location of the stope roof and the caving surface,enabling the mathematical computation of the top caving angle(φ).The drilling method was employed to measure the top caving angle on two extra-thick fully mechanized coal caving faces under the conditions of three geological structures,namely,no geological structure,igneous rock structure,and fault structure.The results show that the value of top caving angle could be accurately estimated on-site with the 9-parameter 3D top coal caving surface model built with the drilling method.This method is a novel on-site measurement that can be easily applied.Our findings reveal that the characteristics of the coal-rock in the two mining faces are different;yet their caving angles follow the ruleφ_(igneous rock structure)<φ_(no geological structure)<φ_(fault structure).Finally,through the data fitting with two indexes(the top coal uniaxial compressive strength and the top caving angle),it is found that the relationship between the two indexes satisfies an exponential decay function.
基金supported by National Natural Science Foundation of China(Nos.51734009,51904290)the Natural Science Foundation of Jiangsu Province,China(BK20180663).
文摘The stability control of gob-side entry retaining in fully mechanized caving face is a typical challenge in many coal mines in China.The rotation and subsidence of the lateral cantilever play a critical role in a coal mine,possibly leading to instability in a coal seam wall or a gob-side wall due to its excessive rotation subsidence.Hence,the presplitting blasting measures in the roof was implemented to cut down the lower main roof and convert it to caved immediate roof strata,which can significantly reduce the rotation space for the lateral cantilever and effectively control its rotation.Firstly,the compatible deformation model was established to investigate the quantitative relationship between the deformation of the coal seam wall and the gob-side wall and the subsidence of the lateral cantilever.Then,the instability judgments for the coal seam wall and gob-side wall were revealed,and the determination method for the optimal roof cutting height were obtained.Furthermore,The Universal Distinct Element Code numerical simulation was adopted to investigate the effect of roof-cutting height on the stability of the retained entry.The numerical simulation results indicated that the deformation of the roadway could be effectively controlled when the roofcutting height reached to 18 m,which verified the theoretical deduction well.Finally,a field application was performed at the No.3307 haulage gateway in the Tangan coal mine,Ltd.,Shanxi Province,China.The field monitoring results showed that the blasting roof cutting method could effectively control the large deformation of surrounding rocks,which provided helpful references for coal mine safety production under similar conditions.
文摘Effective control of roof strata is very important for trouble free operation and regular face advance in mechanised longwall workings. It is now technically possible to exploit coal seams in difficult geomining conditions with the help of newer innovations in longwall face machineries. A reliable assessment of caving behaviour and support capacity requirement helps in selecting supports of adequate capacity and making operational preparedness for timely and confident solution of impending problems.This paper reviews the mechanism of roof caving and the conventional approaches of caving behaviour and support requirement in the context of major strata control experiences gained worldwide. The review shows that a number of approaches are being used for advance prediction of caving behaviour and support capacity requirement in a variety of geo-mining conditions. The theoretical explanation of the mechanism of roof caving and the design function of roof supports have been worked out through staged development of approaches, their evaluation followed by their gradual modification and enrichment of synthesized findings. This process is still continuing with consistently improved understanding through growing field experiences in the larger domain of geo-mining conditions and state-of-art strata analysis and monitoring techniques. These attempts have contributed significantly to improving the level of understanding and reducing the gap of uncertainty in planning and design of longwall operation in a given geo-mining condition.
基金This work is funded by the National Natural Science Foundation of China(Grant No.51934008,51674264 to Jiachen Wang,Grant No.51974320 to Shengli Yang)Fundamental Research Funds for the Central Universities(Grant No.06500182 to Zhengyang Song)Funds from State Key Laboratory of Coal Resources in Western China(SKLCRKF20-07 to Zhengyang Song).
文摘This review details the state of the art in research on top coal drawing mechanisms in Longwall top coal caving(LTCC)by examining the relevant literature over the last two decades.It startswith an introduction of the brief history and basic procedures of LTCC.The framework of research on the drawing mechanism,basic concepts,and some theoretical models of LTCC are detailed in sect.research framework of top coal drawingmechanism.The authors note that theTop coal drawbody(TCD),Top coal boundary(TCB)and Top coal recovery ratio(TCRR)are key factors in the drawingmechanism.TheBody-boundary-ratio(BBR)research system has been the classic framework for research over the last 20 years.The modified Bergmark-Roos model,which considers the effects of the supporting rear canopy,flowing velocity of top coal,and its shape factor,is optimal for characterizing the TCD.A 3Dmodel to describe the TCB that considers the thicknesses of the coal seam and roof strata is reviewed.In sect.physical testing and numerical simulation,the physical tests and numerical simulations in the literature are classified for ease of bibliographical review,and classic conclusions regarding the drawing mechanism of top coal are presented and discussedwith elaborate illustrations and descriptions.The deflection of the TCDis noted,and is caused by the shape of the rear canopy.The inclined coal seam always induces a largerTCD,and a deflection in theTCDhas also been observed in it.The effects of the drawing sequence and drawing interval on the TCRR are reviewed,where a long drawing interval is found to lead to significant loss of top coal.Its flowing behavior and velocity distribution are also presented.Sect.practical applications of drawingmechanisms forLTCCmines 4 summarizes over 10 cases where the TCRRof LTCCmines improved due to the guidance of the drawing mechanism.The final section provides a summary of the work here and some open questions.Prospective investigations are highlighted to give researchers guidance on promising issues in future research on LTCC.
基金supported by the National Key R&D Plan of China,China(Grant No.2018YFC0604501)the Natural Science Foundation of China,China(Grant Nos.51934008,51674264,51904305)the Research Fund of the State Key Laboratory of Coal Resources and Safe Mining,CUMT,China(Grant No.SKLCRSM19KF023).
文摘The size distribution of the broken top coal blocks is an important factor,affecting the recovery ratio and the efficiency of drawing top coal in longwall top coal caving(LTCC)mining panel.The standard deviation of top coal block size(dt)is one of the main parameters to reflect the size distribution of top coal.To find the effect of dt on the caving mechanism,this study simulates experiments with 9 different dt by using discrete element software PFC.The dt is divided into two stages:uniform distribution stage(UDS)whose dt is less than 0.1(Schemes 1–5),and nonuniform distribution stage(NDS)whose dt is more than 0.1(Schemes 6–9).This research mainly investigates the variation of recovery ratio,drawing body shape,boundary of top coal,and contact force between particles in the two stages,respectively.The results showed that with the increasing dt,the recovery ratio of the panel increases first and then decreases in UDS.It is the largest in Scheme 3,which mainly increases the drawing volume at the side of starting drawing end.However,the recovery ratio decreases first and then increases quickly in NDS,and it is the largest in Scheme 9,where the drawing volume at the side of finishing drawing end are relatively higher.In UDS,the major size of top coal is basically medium,while in NDS,the size varies from medium to small,and then to large,with a distinct difference in shape and volume of the drawing body.When the major size of top coal is medium and small,the cross-section width of the initial boundary of top coal at each height is relatively small.Conversely,when the top coal size is large,the initial boundary of top coal has a larger opening range,the rotating angle of lower boundary is relatively small in the normal drawing stage,which is conducive to the development of drawing body and reduces the residual top coal,and the maximum particle velocity and the particles movement angle are both larger.This study lays a foundation for the prediction of recovery ratio,and suggests that the uniform top coal is more manageable and has a larger recovery ratio.
文摘In order to realize the modernized miningmanagementi the authors. based on the practice of a specified mine, developed the application software of the broken ore drawing data management system for sublevel caving through the study on FOXBASE computer language. This paper elabo-rates the overall conception of this system , indicates the main task which should he completed in this system and introduces its module structure and main functions.
基金supported by the Natural Science Foundation of China,China(Grant No.51904305)the Research Fund of the State Key Laboratory of Coal Resources and Safe Mining,China University of Mining and Technology(Grant No.SKLCRSM19KF023)+2 种基金the Fundamental Research Funds for the Central Universities(Grant No.2022YQNY03)the Research Fund of Key Laboratory of Safety and High-efficiency Coal Mining,Ministry of Education(Grant No.JYBSYS2021204)the Open Fund of State Key Laboratory of Coal Resources and Safe Mining(Grant No.SKLCRSM21KFA09).
文摘Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.
文摘This paper analyzes the gas source of the horizontally sectioned fully mechanized caving face in the steeply inclined and extra-thick seam of Adaohai Coal Mine, and numerically simulates the stress distribution and pressure relief of the lower section coal after the upper section working face is mined. It theoretically analyzed the reasonable layout of the drainage boreholes, and designed the drainage borehole layout accordingly. In the upper and lower section of the working face, the actual drainage effect of the boreholes was inspected, and the air exhaust gas volume in the working face was statistically analyzed. It was confirmed that the layout of boreholes was reasonable, the gas control effect of working face was greatly improved and fully met the needs of safe mining. The control effect was greatly improved and the need for safe mining was fully met, and thus a gas drainage technology suitable for the coal seam storage conditions and mining technology of the Adaohai Coal Mine was found. That is to say: the gas emission from the working face of the section mining mainly comes from its lower coal body. Pre-draining the lower coal body of the section and depressurizing gas interception and drainage are the key to effectively solve the problem of gas emission from the working face. Drainage boreholes in the working face of the section should be arranged at high and low positions. The high-level boreholes are located about 2 m from the top of the working face, and the high-level boreholes are about 9 m away from the top of the working face. Through the pre drainage of high and low-level boreholes in advance and the interception and pressure relief drainage, the gas control in the horizontal sublevel fully mechanized caving mining face in steep and extra thick coal seam can realize a virtuous cycle.
基金supported by the UNSW Australia-Vietnam Ministry of Education and Training(MOET)Scholarship Program
文摘Longwall Top Coal Caving has been considered as one of the most effective technologies for the extraction of underground thick coal seams. A large number of studies on the applicability of Longwall Top Coal Caving into new mine sites have linked the success of its application to the geo mechanical understanding of the cavability of the top coal. The paper aims to improve the knowledge of the top coal cavability evaluation. A range of parameters that affect the top coal cavability were first identified. Afterward, a number of cavability assessment methods and classifications were reviewed. The result is important in that it assists researchers in developing an advanced and reliable tool for the top coal cavability evaluation.
基金provided by the National Natural Science Foundation of China(No.51674132)the State Key Research Development Program of China(No.2016YFC0801407-2)+3 种基金the Research Fund of The State Key Laboratory of Coal Resources and Safe Mining,CUMT(No.SKLCRSM15KF04)Natural Science Foundation of Liaoning Province(No.2015020614)Liaoning BaiQianWan Talents Program(No.201575)the Research Fund of State and Local Joint Engineering Laboratory for Gas Drainage & Ground Control of Deep Mines(Henan Polytechnic University)(No.G201602)
文摘Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole photography technique and the seismic CT scanner technique, the deformation and failure of overlying strata of fully mechanized caving face in shallow coal seam were studied and the failure development of overburden was determined. Results show that the full view borehole photography can reveal the characteristics of strata, and the seismic CT scanner can reflect the characteristics of strata between the boreholes. The combined measurement technique can effectively determine the height of fractured and caved zones. The top end of the caved zone in Yangwangou coal mine employing the top coal caving longwall mining was at the depth of 171 m and fractured zone was at the depth of 106-110 m. The results provide a theoretic foundation for controlling the overburden strata in the shallow buried top coal caving panel.
文摘AS a foreigner anywhere, it is important to make an effort to experience the cultural heritage of the city you are in. In Paris you should visit Montmartre, in London you can't miss Buckingham Palace, and before you leave Sydney, a trip to the Blue Mountains is essential, For Beiiing, the unquestionable birthplace of Chinese culture is buried deep within the city's ancient hutongs.
文摘With a history of more than 100 years, Chuquicamata has become one of the largest open pits in the world. Its current depth of 1100 m, length of 4500 m and width of 3000 m, resulting in haulage distances of over 11,000 m from pit bottom to the processing plant or waste dumps, with waste/ore ratio greater than 4 and much lower grades, are effectively determining its profitable limit by the end of this decade. Currently, there are over 4300 Mt of geological resources containing 0.7% of copper and 340 ppm (1 ppm = 1 g/t) of molybdenum below the final pit shell. The corresponding orebody geometry is 3000 m northsouth, 300-800 m eastwest and the drilling campaign suggested the existence of more than 900 m of mineable ore from the final pit bottom. This is in spite of the fact that the Chuquicamata orebody is still open at depth. The business case to continue with the mining of the Chuquicamata orebody is to change from the current large open pit to a novel macroblock variant block caving geometry. This requires a production rate of 140,000 t/d (50 Mt per annum), with a continuous material handling system to achieve the 7-year ramp-up to full production. The resolution of a number of known technical, operational and logistical challenges outside current industry practises which Chuquicamata will face over its projected 40-year mine life is therefore essential. These challenges include simultaneous operations of open pit and underground macroblocks and from the initial lift to the second lift, rapid ramp-up and optimum sequencing of the planned macroblocks, early dilution from the west fault and late dilution from potential slope failures, and the potential for major operational hazards. An equally important issue to be addressed is cultural given that the mining history in the northern region of Chile, which includes Chuquicamata, is predominantly open pit. This paper presents a synopsis of the main challenges that the Chuquicamata underground project will face in order to meet the objectives of its corresponding business case. Those discussed and how they were resolved are: simultaneous operations, rapid ramp-up and optimum sequencing of the planned macroblocks, and early and late dilutions. The project is an example of the fact that there are no recipes or cook books in cave mining.
基金Project(50490274) supported by the National Nature Science Foundation of China
文摘New method for handling roof of the base successive mining is proposed, which is induction caving in the roof. The key is that it is made certain to the station of the space-time in the induction caving roof, as the stress is released with the mining process. And applying the catastrophe theory, the influencing factors of induction caving roof are studied in the emptied areas, such as the mechanical property of the surrounding rock, the area of the gob,the scope and dimension of tensile stress. The results show that the key factor is the area of the gob to the method of the induction caving roof. Then according to the geology and the ore characteristic, the three dimension FEM mechanical model is built in Tongkeng Mine, the laws of the tensile stress are analyzed to the space and the time in the roof with the mining, then it is rational design to the mine step and time of the handing the roof.