Study of beat phenomenon on a pile-supported pipeline system subjected to wave loading

Classical beat phenomenon has been observed in most combined systems. The focus of this paper is to provide a better understanding of this phenomenon in an offshore pile-supported pipeline system. The beat phenomeon is caused by the coupling movement of the pipeline and its vertical pile support under certain conditions. It can induce excessive vibration and cause fatigue failure at pipe elbow. However, in some circumstances it does not exist. Numerical results in both frequency and time domains are presented to elucidate this phenomenon in a combined pipeline system. The conclusions of this paper could give constructive guidance to future design of simply supported pipeline systems.

Novel Manufacturing Technology of Hyperbolic Plates for Shipbuilding

On the basis of the principle of dieless hydrobulging technology, a novel hydrobulging technology for manufacturinghyperbolic plates is proposed. First, a toroidal pipe elbow or a partial toroidal pipe elbow is formed, then the single hydrobulgedstructure can be cut up into some desired plates. It is proved by experiments and finite element simulation that manufacturingtechnology of hyperbolic plates adopting integrated hydrobulging forming technology is feasible.

Flow-induced Noise and Vibration Analysis of a Piping Elbow with/without a Guide Vane

The effect of a guide vane installed at the elbow on flow-induced noise and vibration is investigated in the range of Reynolds numbers from 1.70×10^5 to 6.81×10^5, and the position of guide vane is determined by publications. The turbulent flow in the piping elbow is simulated with large eddy simulation （LES）. Following this, a hybrid method of combining LES and Lighthill＇s acoustic analogy theory is used to simulate the hydrodynamic noise and sound sources are solved as volume sources in code Actran. In addition, the flow-induced vibration of the piping elbow is investigated based on a fluid-structure interaction （FSI） code. The LES results indicate that the range of vortex zone in the elbow without the guide vane is larger than the case with the guide vane, and the guide vane is effective in reducing flow-induced noise and vibration in the 90° piping elbow at different Reynolds numbers.

Influence and optimization of swirler parameters on elbow wear of deep coal fluidization pipeline transportation system

Elbow wear is a major threat to the multiphase pipeline transportation industry,which has a negative impact on the stable operation of the transportation system.In order to find the wear reduction methods of elbows in the fluidization pipeline transportation system for 2000-meter-deep coal resources,the swirler was installed upstream of the elbows,and wear simulations and tests of three kinds of elbows were carried out.The results showed that the maximum wear rate(MWR)of elbows increased and then decreased along the elbow angle.Due to the different directions of gravity,the heavy wear position(HWP)of the horizontal-vertical(H-V)elbow was in front of the vertical-horizontal(V-H)elbow.Because the downstream portion of the horizontal-horizontal(H-H)elbow was still a horizontal pipe,the HWP of the H-H elbow almost covered the whole elbow.The swirler placed upstream of the elbows could make the particles at the elbow move to the intrados of the elbows,resulting in less collision between the particles and the extrados of the elbows,thus reducing the wear of the elbows.The wear reduction effects of swirlers on three different elbows were favorably connected with the guide vane angle(GVA)and negatively correlated with the guide vane length(GVL),decreased first and then increased as the guide vane height(GVH)increased,and were little affected by the guide vane number(GVN)and the guide vane thickness(GVT).The mathematical models between the MWR of the elbows and guide vane parameters were established.By bench tests,the wear reduction effect of three kinds of elbows under the optimal guide vane parameters was 58.4%,76.9%,and 78.6%,respectively.The errors between the bench test results and the simulation results were around 10%.

Limit Analysis of Defect-Free Pipe Elbow Under Internal Pressure With Mean Yield Criterion

With mean yield（MY）criterion,an analytical solution of the collapse load for a defect-free pipe elbow under internal pressure is first obtained.It is a function of ratio of thickness to radius t0/r0,strain hardening exponent n,curvature influence factor mand ultimate tensile strength.The collapse load increases with the increase of m,and it is the same as the burst pressure of straight pipe if m=1is assumed.The MY-based solution is compared with those based on Tresca,Mises and twin shear stress（TSS）yield criteria,and the comparison indicates that Tresca and twin shear stress yield criteria predict a lower bound and an upper bound to the collapse load respectively.However,the MY-based solution lies just between the TSS and Tresca solutions,and almost has the same precision with the Mises solution.

Numerical simulation of water-slag elbow erosion-inhibiting by regulating the slag injection position with a novel preceding rotating sheet structure

The elbow erosion seriously jeopardizes the safe and stable operation of water–slag discharge pipeline of the coal gasification system.This work simulated water–slag elbow characteristics with various slag injection positions by simulating five simplified and representative erosion categories,including A-type horizontal-vertical elbow with an upstream flow,B-type horizontal-vertical elbow with a downstream flow,C-type vertical-horizontal elbow with an upstream flow,D-type vertical-horizontal elbow with a downstream flow and E-type horizontal-horizontal elbow.Compared with the C/D-type elbow,where particles were injected uniformly,the A-type elbow and E-type elbow were found to increase erosion rate,while the B-type elbow decreases erosion rate.An interesting discovery is that the elbow erosion rate is relatively low for small particles when particles are injected from the middle and bottom positions of the inlet section of the elbow.Based on the observation,a novel preceding rotating sheet structure was developed to regulate the particle injection position.It shows an excellent anti-erosion performance by reducing the maximum erosion rate of particles with diameters of 50,100,and 200μm by 23%,35%,and 43%,respectively.