Effects of Ce in novel bronze and its plasma sprayed coating

A novel aluminum bronze over the Cu-Al binary alloy eutectoid Cu-14Al-4.5Fe was prepared by a jointly-charging one-melting technique and conventional sand casting. The bronze coatings were atmospherically plasma sprayed on the 45# medium carbon steel substrate. The effect of rare earth Ce on the microstructures and Vickers hardness of the cast alloy and coatings were characterized by scanning electron microscopy, X-ray diffraction, electronic probe microanalysis, transmission electron microscopy and microhardness measurements. The results indicate that the hardness of both as-cast alloy and coating are enhanced by the addition of 0.6% Ce due to the refinement of κ phases which are well distributed in the matrix. The rapid solidification in the plasma spray processing retains Fe-supersaturated in the Al-bronze alloy coatings, which avoids the formation of eutectoid （α＋γ2） phase and stacking faults are found in the coatings with Ce added, accordingly improves the mechanical properties.

Formation process of composite plasma electrolytic oxidation coating containing zirconium oxides on AM50 magnesium alloy

The formation processes of a composite ceramic coating on AM50 magnesium alloy prepared by plasma electrolytic oxidation （PEO） in a K 2 ZrF 6 electrolyte solution were studied by scanning electron microscope （SEM） and energy dispersive X-ray spectroscope （EDX）. Electrochemical impedance spectroscopy （EIS） tests were used to study the variation of the corrosion resistance of the coating during the PEO treatment. The results show that the coating formed on Mg alloy is mainly composed of MgO and MgF 2 when the applied voltage is lower than the sparking voltage, and zirconium oxides start to be deposited on Mg substrate after the potential exceeding the sparking voltage. The corrosion resistance of the coating increases with increasing the applied voltage.

HOT CORROSION OF A PLASMA SPRAYED CoNiCrAlTaSiY COATING

Hot corrosion(HC) of the APS(atomospheric plasma spraying)CoNiCrAlTaSiY coating on a nickel-base superalloy GH864 has been studied. The effect of laser-treatment on hot corrosion resistance was also examined.It was shown that CoNiCrAlTaSiY coating had superior properties in resistance to hot corrosion due to the readiness of the formation of a protective Cr2O3 scale on the coating surface.A model for the mechanism of hot corrosion of this coating has been suggested. Hot corrosion resistance of this coating was significantly increased by the laser treatment simply because the surface of the as sprayed coating was densified by the high power laser beam.

Iridium Coating Deposited by Double Glow Plasma Technique——Effect of Glow Plasma on Structure of Coating at Single Substrate Edge

Double glow plasma technique has a high deposition rate for preparing iridium coating. However, the glow plasma can influence the structure of the coating at the single substrate edge. In this study, the iridium coating was prepared by double glow plasma on the surface of single niobium substrate. The microstructure of iridium coating at the substrate edge was observed by scanning electron microscopy. The composition of the coating was confirmed by energy dispersive spectroscopy and X-ray diffraction. There was a boundary between the coating and the substrate edge. The covered area for the iridium coating at the substrate edge became fewer and fewer from the inner area to the outer flange-area. The bamboo sprout-like particles on the surface of the substrate edge were composed of elemental niobium. The substrate edge was composed of the Nb coating and there was a transition zone between the Ir coating and the Nb coating. The interesting phenomenon of the substrate edge could be attributed to the effects of the bias voltages and the plasma cloud in the deposition chamber. The substrate edge effect could be mitigated or eliminated by adding lots of small niobium plates around the substrate in a deposition process.

Effect of Laser Remelting on the Microstructure and Corrosion Resistance of Plasma Sprayed Fe-based Coating

Fe-based amorphous and nanocrystalline coatings were fabricated by air plasma spraying. The coatings were further treated by laser remelting process to improve their microstructure and properties. The corrosion resistance of the as-sprayed and laser-remelted coatings in 3.5wt% NaC1 and 1 mol/L HCI solutions was evaluated by electrochemical polarization analysis. It was found that laser-remelted coating appeared much denser than the as-sprayed coating. However, laser-remelted coating contains much more nanocrystalline grains than the as-sprayed coatings, resulting from the lower cooling rate in laser remelting process compared with plasma spraying process. Electrochemical polarization results indicated that the laser-remelted coating has great corrosion resistance than the as-sprayed coating because of its dense structure.

Preparation and properties of the Ni-Al/Fe-Al intermetallics composite coating produced by plasma cladding

A novel approach to produce an intermetallic composite coating was put forward.The microstructure,microhardness,and dry-sliding wear behavior of the composite coating were investigated using X-ray diffraction （XRD）,scanning electron microscopy （SEM）,energy dispersive spectrum （EDS） analysis,microhardness test,and ball-on-disc wear experiment.XRD results indicate that some new phases FeAl,Fe0.23Ni0.77Al,and Ni3Al exit in the composite coating with the Al2O3 addition.SEM results show that the coating is bonded with carbon steel metallurgically and exhibits typical rapid directional solidification structures.The Cr7C3 carbide and intermetallic compounds co-reinforced composite coating has a high average hardness and exhibits an excellent wear resistance under dry-sliding wear test compared with the Cr7C3 carbide-reinforced composite coating.The formation mechanism of the intermetallic compounds was also investigated.

Microstructure and corrosion resistance of Fe/Mo composite amorphous coatings prepared by air plasma spraying

Fe/Mo composite coatings were prepared by air plasma spraying （APS） using Fe-based and Mo-based amorphous and nanocrys- talline mixed powders. Microstructural studies show that the composite coatings present a layered structure with low porosity due to adding the self-bonded Mo-based alloy. Corrosion behaviors of the composite coatings, the Fe-based coatings and the Mo-based coatings were in- vestigated by electrochemical measurements and salt spray tests. Electrochemical results show that the composite coatings exhibit a lower polarization current density and higher corrosion potentials than the Fe-based coating when tested in 3.5wt% NaC1 solutions, indicating supe- rior corrosion resistance compared with the Fe-based coating. Also with the increase in addition of the Mo-based alloy, a raised corrosion re- sistance, inferred by an increase in corrosion potential and a decrease in polarization current density, can be found. The results of salt spray tests again show that the corrosion resistance is enhanced by adding the Mo-based alloy, which helps to reduce the porosity of the composite coatings and enhance the stability of the passive films.

Excellent plasma electrolytic oxidation coating on AZ61 magnesium alloy under ordinal discharge mode

In the preparation of plasma electrolytic oxidation(PEO)coating,the rapid heating of freely-happened electron avalanche under traditional discharge(TD)mode inevitably results in a strong eruption of electric breakdown melt.The PEO coating is loose and invariably composed of a very thin inner dense layer and an outer loose layer,as a result of which its properties and application have been limited greatly.In this work,for purpose of weakening the eruption of breakdown melt,thickening the inner dense layer,densifying the outer loose layer and improving the performance of PEO coating,ordinal discharge(OD)mode of PEO coating is developed by regulating the mass ratio of MgF_(2) to MgO(α)and voltage in the PEO investigation on AZ61 magnesium alloy in KF-KOH electrolyte.The formation mechanism under different discharge mode,electrochemical corrosion and wear of PEO coatings are investigated.The results show that the suitableαand voltage for effective OD are 1.3 and 130 V under which the freely-happened electron avalanche in MgF_(2) under TD mode can be restricted by the adequate adjacent MgO.Compared with TD mode,the inner dense layer,in which the(10¯1)plane of MgF_(2) is parallel to the(111)plane of MgO at their well-knit semi-coherent interface,is thickened to 2.4∼7.2 times,the corrosion potential(E_(corr))improvement is enlarged to 3.6∼13.2 times and the corrosion current intensity(I_(corr))is reduced from 10.8∼9.499 to 0.433(10^(−6) A/cm^(2)).The outer loose layer is densified and the wear rate is lessened 65.5%∼89.8%by the evident melioration in surface porosity,impedance and hardness.This work deepens the understanding about the discharge of PEO coating and provides an available OD mode for preparing excellent PEO coating.

Fatigue Delamination Characteristics of Plasma Sprayed Coatings under Fretting

The fretting wear behavior of plasma spraying CoCrW and Cr3C2-NiCr coatings were investigated. The results showed both plasma spraying coatings were inferior to K417 nickel superalloy in the fretting wear resistance. The characterized fatigue delamination of the plasma sprayed coatings was evidently different from that of the homogeneous materials. The lamellar cohesion, oxide inclusions and porosity were critical factors that controlled the fretting wear resistance. In the view of contact mechanics, the fretting wear behavior of plasma spraying coatings was characterized.

Microstructure evolution and mechanical properties of Ti-B-N coatings deposited by plasma-enhanced chemical vapor deposition

Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analysis,X-ray photoelectron spectroscopy,scanning electron microscope,and high-resolution transmission electron microscope,the influences of B content on the microstructure and properties of Ti B N coatings were investigated systematically.The results indicated that the microstructure and mechanical properties of Ti-B-N coatings largely depend on the transformation from FCC-TiN phase to HCP-TiB2 phase.With increasing B content and decreasing N content in the coatings,the coating microstructure evolves gradually from FCC-TiN/a-BN to HCP-TiB2 /a-BN via FCC-TiN+HCP-TiB2/a-BN.The highest microhardness of about 34 GPa is achieved,which corresponds to the nanocomposite Ti-63%B-N (mole fraction) coating consisting of the HCP-TiB2 nano-crystallites and amorphous BN phase.The lowest friction-coefficient was observed for the nanocomposite Ti-41%B-N (mole fraction) coating consisting of the FCC-TiN nanocrystallites and amorphous BN

Abrasive wear behavior of cast iron coatings plasma-sprayed at different mild steel substrate temperatures

Three kinds of cast iron coatings were prepared by atmospheric plasma spraying. During the spraying, the mild steel substrate temperature was controlled to be averagely 50, 180, and 240℃, respectively. Abrasive wear tests were conducted on the coatings under a dry friction condition. It is ibund that the abrasive wear resistance is enhanced with the substrate temperature increasing. SEM observations show that the wear losses of the coatings during the wear tests mainly result from the spalling of the splats. Furthermore, the improved wear resis- tance of the coatings mainly owes to the formation of oxides and the enhancement in the mechanical properties with the substrate temperature increasing.

Microstructure studies of air-plasma-spray-deposited CoNiCrAlY coatings before and after thermal cyclic loading for high-temperature application

In the present study, bond-coats for thermal barrier coatings were deposited via air plasma spraying（APS） techniques onto Inconel 800 and Hastelloy C-276 alloy substrates. Scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, X-ray diffraction（XRD）, and atomic force microscopy（AFM） were used to investigate the phases and microstructure of the as-sprayed, APS-deposited Co Ni Cr Al Y bond-coatings. The aim of this work was to study the suitability of the bond-coat materials for high temperature applications. Confirmation of nanoscale grains of the γ/γ′-phase was obtained by TEM, high-resolution TEM, and AFM. We concluded that these changes result from the plastic deformation of the bond-coat during the deposition, resulting in Co Ni Cr Al Y bond-coatings with excellent thermal cyclic resistance suitable for use in high-temperature applications. Cyclic oxidative stability was observed to also depend on the underlying metallic alloy substrate.

Effect of Thermal Treatment on the Grain Growth of Nanostructured YSZ Thermal Barrier Coating Prepared by Air Plasma Spraying

A nanostructured thermal barrier coating is prepared by air plasma spraying using the 8wt% Y_2O_3 partially stabilized zirconia nano-powder with an average grain size of 40 nm. The microstructure and phase composition of feedstock nano-powder and coating are investigated using SEM, TEM and XRD. It is found that the as-sprayed zirconia coating has an average grain size of 67 nm and mainly consistes of metastable tetragonal phase, together with some monoclinic phase and tetragonal phase. Thermal treatment results show that the grains of the nanostructured coating grow slightly below 900℃, whereas over 1000℃ the gains grow rapidly and monoclinic phase noticeably appeares.

Structure and Oxidation Behavior of a Plasma Sprayed Yttrium Silicates Coated SiC-C/C with a Glass Outer Sealant from 1573K to 1873K

Different compositions of yttrium silicates coatings were deposited on SiC-C/C by plasma spraying and an outer borosilicate glass was applied on the yttrium silicates coatings surfaces. The structure of the multi-layer coatings was characterized by XRD and SEM analyses. High temperature oxidation behavior of the multi-layer coatings coated C/C composites was investigated. Results show that SiC/2SiO2 Y2O3/1.5SiO2 Y203/ SiO2 Y2O3/glass multi-layer coating has better high temperature oxidation resistance, protecting carbon/ carbon composites from oxidation at 1 773 K in air for 164 h with the weight loss of 1.65%. The oxidation weight loss of the coated C/C with time accorded with parabolic rule in the temperature range 1 573 K-1 873 K; and the corresponding oxidation activation energy of the coated carbon/carbon composites is 132.2 kJ/mol.

Nanostructured yttria stabilized zirconia coatings deposited by air plasma spraying

Nanostructured yttria partially stabilized zirconia coatings were deposited by air plasma spraying with reconstituted nanosized powder. The microstructures and phase compositions of the powder and the as-sprayed nanostructured coatings were characterized by transmission electron microscopy(TEM), scanning electron microscopy(SEM) and X-ray diffraction(XRD). The results demonstrate that the microstructure of as-sprayed nanostructured zirconia coating exhibits a unique tri-modal distribution including the initial nanostructure of the powder, equiaxed grains and columnar grains. Air plasma sprayed nanostructured zirconia coatings consist of only the nontransformable tetragonal phase, though the reconstituted nanostructured powder shows the presence of the monoclinic, the tetragonal and the cubic phases. The mean grain size of the coating is about 42 nm.

Preparation and characterization of nanostructured Al_2O_3-13wt.%TiO_2 ceramic coatings by plasma spraying

Nanostructured and conventional Al2O3-13wt.%TiO2 ceramic coatings were prepared by plasma spraying with nanostructured agglomerated and conventional powders, respectively. The microstructure and microhardness of the coatings were investigated using scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and microhardness measurement. Meanwhile, the friction and wear behaviors were analyzed and compared using a ball-on-disk tribometer. The results show that the conventional coating has lamellar stacking characteristic and has some pores. However, the nanostructured coating shows a bimodal microstructure, which is composed of both fully melted regions and partially melted regions. According to the microstructural difference, the partially melted regions can be divided into liquid-phase sintered regions （a three-dimensional net or skeleton-like structure： Al2O3-rich submicron particles embedded in the TiO2-rich matrix） and solid-phase sintered regions （remained nanoparticles）. The microstructural characteristics of the liquid-phase sintered region are formed due to the selective melting of TiO2 nanoparticles during plasma spraying. On the other hand, the TiO2 and Al2O3 nanoparticles of the solid-phase sintered regions are all unmelted during plasma spraying. Due to the existence of nanostructured microstructures, the nanostructured coating has a higher microhardness, a lower friction coefficient, and a better wear resistance than the conventional coating.

Protection Performance of Plasma Sprayed Al_(2)O_(3)-13 wt%TiO_(2) Coating Sealed with an Organic-inorganic Hybrid Agent

An organic-inorganic hybrid sealing agent was fabricated and used in the plasma sprayed Al_(2)O_(3)-13 wt%TiO_(2)coating,and conventional silicone agent was also used for comparison.Protection performance of the coatings was comprehensively evaluated based on both anti-corrosion and anti-biofouling properties.The results reveal that the sealing treatment is remarkably useful to decrease the porosity of the coating,and the porosity of the coating sealed with the hybrid agent is only 0.035%.Immersion corrosion test and Tafel polarization test reveal that the sealed coating with the hybrid agent exhibits a better corrosion resistance by compared with the coating sealed with silicone agent.The corrosion current density i_(corr) of the hybrid agent sealed coating is only 0.7×10^(-6)A·cm^(-2).Moreover,anti-biofouling tests both in the outdoor analogue hydraulic environment and in the natural marine environment prove that the mentioned novel coating presents a better combination of corrosion resistance and anti-biofouling property by compared with the other coatings,and it could be used as a protection of metal components in the marine environment.

Plasma Spray Forming of Nanostructured Composite Coatings

The nanostructure composite coating is obtained via plasma spraying of Al2O3-13 wt pct TiO2 powder. Brittle and hard lamella results from melted nanostructured powder. Ductile nanostructured matrix forms from unmelted nanostructured particles. Through the adjustment of constituent and nanostructure, hardness/strength and toughness/ductility are balanced and overall properties of the structure composite are achieved.

Characterization of NbSi_2–Al_2O_3 nanocomposite coatings prepared with plasma spraying mechanically alloyed powders

The present study characterized NbSi2-Al2O3 nanocomposite powders plasma-sprayed on Ti-6Al-4Vsubstrates. The powders were agglomerated to obtain suitable particle sizes for spraying. The agglomerated powders were then plasma-sprayed using atmospheric plasma spraying. The structural transformations of the powders along with the morphological and mechanical changes of the coatings were examined by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, and hard- ness testing. The results showed that after plasma spraying, the grain size increased, and the lattice strain decreased. However, the grain size of this compound after spraying was still in the nanometer range. The coating was uniform and exhibited good adhesion to the substrate. The microhardness and fracture toughness of the nanocomposite coating were higher than those of a nanostructured NbSi2 coating.

Primary Results of Lithium Coating for the Improvement of Plasma Performance in EAST

First lithium coating associated with ion cyclotron range of frequency （ICRF） plasma was performed successfully in EAST. Results in reduction of both residual impurity and deuterium in the vacuum vessel were obtained. Particularly the partial pressure of deuterium after the lithium coating was reduced by about a factor of 5. Impurity radiation in the plasma was reduced and electron temperature increased by about 50%. Moreover, reproducible plasma discharges with high parameters, such as higher plasma current and density, could be easily obtained. These results showed that plasma performance was improved. Even though only 2 g of lithium were injected, the effective lifetime of the Li film was raised up to 40 shots.