1 Scope This standard specifies the definition, classification, technical requirements, test methods, inspection rules, packing, marking, transportation and quality certificate of corundum block containing plastic ph...1 Scope This standard specifies the definition, classification, technical requirements, test methods, inspection rules, packing, marking, transportation and quality certificate of corundum block containing plastic phase.展开更多
Additive manufacturing technology based on laser powder bed fusion(LPBF)offers a novel approach for fabricating bulk metallic glass(BMG)products without restriction in size and geometry.Nevertheless,the BMGs prepared ...Additive manufacturing technology based on laser powder bed fusion(LPBF)offers a novel approach for fabricating bulk metallic glass(BMG)products without restriction in size and geometry.Nevertheless,the BMGs prepared by LPBF usually suffered from less plasticity and poorer fracture toughness as compared to their cast counterparts due to partial crystallization in heat-affected zones(HAZs).Since crystallization in HAZs is hard to avoid completely in LPBF BMGs,it is desirable to design a suitable alloy system,in which only ductile crystalline phase,instead of brittle intermetallics,is formed in HAZs.This unique structure could effectively increase the toughness/plasticity of the LPBF BMGs.To achieve this goal,a quaternary BMG system with a composition of Zr_(47.5)Cu_(45.5)Al_(5)Co_(2)is adopted and subjected to LPBF.It is found that nearly a single phase of B_(2)-ZrCu is precipitated in HAZs,while a fully amorphous phase is formed in molten pools(MPs).This B_(2)phase reinforced BMG composite exhibits excellent mechanical properties with enhanced plasticity and toughness.Furthermore,it is easy to modulate the mechanical properties by altering the amount of the B_(2)phase via adjusting the laser energy input.Finally,the best combination of strength,plasticity,and notch toughness is obtained in the BMG composite containing 27.4%B_(2)phase and 72.6%amorphous phase,which exhibits yield strength(σ_(s))of 1423 MPa,plastic strain(ε_(p))of 4.65%,and notch toughness(K_(q))of 53.9 MPa m 1/2.Furthermore,a notable strain-hardening is also observed.The improvement of plasticity/toughness and appearance of strain-hardening behavior are mainly due to the martensite phase transformation from the B_(2)phase to the Cm phase during plastic deformation(i.e.,the phase transformation-induced plasticity effect).The current work provides a guide for making advanced BMGs and BMG composites by additive manufacturing.展开更多
An interaction between ferrite recrystallization and austenite transformation in low-carbon steel occurs when recrystallization is delayed until the intercritical temperature range by employing high heating rate. The ...An interaction between ferrite recrystallization and austenite transformation in low-carbon steel occurs when recrystallization is delayed until the intercritical temperature range by employing high heating rate. The kinetics of recrystallization and transformation is affected by high heating rate and such an interaction. In this study, different levels of strain are applied to low-carbon steel using a severe plastic deformation method. Then, ultra-rapid annealing is performed at different heating rates of 200–1100°C/s and peak temperatures of near critical temperature. Five regimes are proposed to investigate the effects of heating rate, strain, and temperature on the interaction between recrystallization and transformation. The microstructural evolution of severely deformed low-carbon steel after ultra-rapid annealing is investigated based on the proposed regimes. Regarding the intensity and start temperature of the interaction, different microstructures consisting of ferrite and pearlite/martensite are formed. It is found that when the interaction is strong, the microstructure is refined because of the high kinetics of transformation and recrystallization. Moreover, strain shifts an interaction zone to a relatively higher heating rate. Therefore, severely deformed steel should be heated at relatively higher heating rates for it to undergo a strong interaction.展开更多
The effects of Laves phase formation and growth on creep rupture behaviors of P92 steel at 883 K were studied.The microstructural evolution was characterized using scanning electron microscopy and transmission electro...The effects of Laves phase formation and growth on creep rupture behaviors of P92 steel at 883 K were studied.The microstructural evolution was characterized using scanning electron microscopy and transmission electron microscopy.Kinetic modeling was carried out using the software DICTRA.The results indicated Fe_2(W,Mo)Laves phase has formed during creep with 200 MPa applied stress at 883 Kfor 243 h.The experimental results showed a good agreement with thermodynamic calculations.The plastic deformation of laths is the main reason of creep rupture under the applied stress beyond 160 MPa,whereas,creep voids initiated by coarser Laves phase play an effective role in creep rupture under the applied stress lower than 160 MPa.Laves phase particles with the mean size of 243 nm lead to the change of creep rupture feature.Microstructures at the vicinity of fracture surface,the gage portion and the threaded ends of creep rupture specimens were also observed,indicating that creep tensile stress enhances the coarsening of Laves phase.展开更多
Development of high-performance phase transformation electrodes in lithium ion batteries requires comprehensive studies on stress-mediated lithiation involving migration of the phase interface. It brings out many coun...Development of high-performance phase transformation electrodes in lithium ion batteries requires comprehensive studies on stress-mediated lithiation involving migration of the phase interface. It brings out many counter-intuitive phenomena, especially in nanoscale electrodes, such as the slowing down migration of phase interface, the vanishing of miscibility gap under high charge rate, and the formation of surface crack during lithiation. However, it is still a challenge to simulate the evolution of stress in arbitrarily-shaped nanoscale electrodes, accompanied with phase transformation and concurrent plastic deformation. This article gives a brief review of our efforts devoted to address these issues by developing phase field model and simulation. We demonstrate that the miscibility gap of two-phase state is affected not only by stress but also by surface reaction rate and particle size. In addition, the migration of phase interface slows down due to stress. It reveals that the plastic deformation generates large radial expansion, which is responsible for the transition from surface hoop compression to surface hoop tension that may induce surface crack during lithiation. We hope our effort can make a contribution to the understanding of stress-coupled kinetics in phase transformation electrodes.展开更多
Billets of Mg-9Al-3Zn-1Mn-6Ca-2Nd alloy were produced by spray-deposition(the Osprey process).Effect of rolling deformation(T = 350?C, ε = 5%, 10%, and 15%, respectively) on microstructure and texture evolution ...Billets of Mg-9Al-3Zn-1Mn-6Ca-2Nd alloy were produced by spray-deposition(the Osprey process).Effect of rolling deformation(T = 350?C, ε = 5%, 10%, and 15%, respectively) on microstructure and texture evolution of the Mg-9Al-3Zn-1Mn-6Ca-2Nd alloy was investigated by scanning electron microscopy(SEM), transmission electron microscopy(TEM) and X-ray diffraction(XRD). Results show that at pass reduction of ε = 5%, 10% and 15% at 350?C respectively, Mg-Nd-Zn typed 24R-LPSO structure was formed in(Ca, Nd)Al2phase(C15 Laves phase). With the increase in pass reduction(i.e. 5%, 10% and 15%), the texture pole density level of basal texture(0002) changed little and pyramidal texture(10 1ˉ3) were increased.In contrast, those of prismatic texture {101ˉ0} 〈11 2ˉ0〉 were increased initially and followed by a reduction, indicating texture randomization in the grain-refined Mg alloy. The combined contribution of LPSO phase and C15 phase was key to randomize the texture of the grain-refined Mg alloy. It was noted that the microcosmic plastic deformation of LPSO phase and nanometer-sized dispersed C15 phase impeded dislocation movement, led to dislocation tangles, and facilitated recrystallization.展开更多
文摘1 Scope This standard specifies the definition, classification, technical requirements, test methods, inspection rules, packing, marking, transportation and quality certificate of corundum block containing plastic phase.
基金supported by the National Natural Science Foundation of China(Grant Nos.52192604 and 52201181)the Key R&D Program of Hubei(No.2022BAA023).
文摘Additive manufacturing technology based on laser powder bed fusion(LPBF)offers a novel approach for fabricating bulk metallic glass(BMG)products without restriction in size and geometry.Nevertheless,the BMGs prepared by LPBF usually suffered from less plasticity and poorer fracture toughness as compared to their cast counterparts due to partial crystallization in heat-affected zones(HAZs).Since crystallization in HAZs is hard to avoid completely in LPBF BMGs,it is desirable to design a suitable alloy system,in which only ductile crystalline phase,instead of brittle intermetallics,is formed in HAZs.This unique structure could effectively increase the toughness/plasticity of the LPBF BMGs.To achieve this goal,a quaternary BMG system with a composition of Zr_(47.5)Cu_(45.5)Al_(5)Co_(2)is adopted and subjected to LPBF.It is found that nearly a single phase of B_(2)-ZrCu is precipitated in HAZs,while a fully amorphous phase is formed in molten pools(MPs).This B_(2)phase reinforced BMG composite exhibits excellent mechanical properties with enhanced plasticity and toughness.Furthermore,it is easy to modulate the mechanical properties by altering the amount of the B_(2)phase via adjusting the laser energy input.Finally,the best combination of strength,plasticity,and notch toughness is obtained in the BMG composite containing 27.4%B_(2)phase and 72.6%amorphous phase,which exhibits yield strength(σ_(s))of 1423 MPa,plastic strain(ε_(p))of 4.65%,and notch toughness(K_(q))of 53.9 MPa m 1/2.Furthermore,a notable strain-hardening is also observed.The improvement of plasticity/toughness and appearance of strain-hardening behavior are mainly due to the martensite phase transformation from the B_(2)phase to the Cm phase during plastic deformation(i.e.,the phase transformation-induced plasticity effect).The current work provides a guide for making advanced BMGs and BMG composites by additive manufacturing.
基金the research board of the Sharif University of Technology for financial support and the provision of the research facilities used in this work
文摘An interaction between ferrite recrystallization and austenite transformation in low-carbon steel occurs when recrystallization is delayed until the intercritical temperature range by employing high heating rate. The kinetics of recrystallization and transformation is affected by high heating rate and such an interaction. In this study, different levels of strain are applied to low-carbon steel using a severe plastic deformation method. Then, ultra-rapid annealing is performed at different heating rates of 200–1100°C/s and peak temperatures of near critical temperature. Five regimes are proposed to investigate the effects of heating rate, strain, and temperature on the interaction between recrystallization and transformation. The microstructural evolution of severely deformed low-carbon steel after ultra-rapid annealing is investigated based on the proposed regimes. Regarding the intensity and start temperature of the interaction, different microstructures consisting of ferrite and pearlite/martensite are formed. It is found that when the interaction is strong, the microstructure is refined because of the high kinetics of transformation and recrystallization. Moreover, strain shifts an interaction zone to a relatively higher heating rate. Therefore, severely deformed steel should be heated at relatively higher heating rates for it to undergo a strong interaction.
基金Item Sponsored by National Natural Science Foundation of China(51201061,51475315)China Postdoctoral Science Foundation(2015M571804)Natural Science Foundation of Jiangsu Province of China(BK20150329)
文摘The effects of Laves phase formation and growth on creep rupture behaviors of P92 steel at 883 K were studied.The microstructural evolution was characterized using scanning electron microscopy and transmission electron microscopy.Kinetic modeling was carried out using the software DICTRA.The results indicated Fe_2(W,Mo)Laves phase has formed during creep with 200 MPa applied stress at 883 Kfor 243 h.The experimental results showed a good agreement with thermodynamic calculations.The plastic deformation of laths is the main reason of creep rupture under the applied stress beyond 160 MPa,whereas,creep voids initiated by coarser Laves phase play an effective role in creep rupture under the applied stress lower than 160 MPa.Laves phase particles with the mean size of 243 nm lead to the change of creep rupture feature.Microstructures at the vicinity of fracture surface,the gage portion and the threaded ends of creep rupture specimens were also observed,indicating that creep tensile stress enhances the coarsening of Laves phase.
基金supported by the National Natural Science Foundation of China (Grant no. 11472262)the Strategic Priority Research Program of the Chinese Academy of Sciences (Grant no. XDB22040502)+1 种基金the Collaborative Innovation Center of Suzhou Nano Science and Technologythe Fundamental Research Funds for the Central Universities
文摘Development of high-performance phase transformation electrodes in lithium ion batteries requires comprehensive studies on stress-mediated lithiation involving migration of the phase interface. It brings out many counter-intuitive phenomena, especially in nanoscale electrodes, such as the slowing down migration of phase interface, the vanishing of miscibility gap under high charge rate, and the formation of surface crack during lithiation. However, it is still a challenge to simulate the evolution of stress in arbitrarily-shaped nanoscale electrodes, accompanied with phase transformation and concurrent plastic deformation. This article gives a brief review of our efforts devoted to address these issues by developing phase field model and simulation. We demonstrate that the miscibility gap of two-phase state is affected not only by stress but also by surface reaction rate and particle size. In addition, the migration of phase interface slows down due to stress. It reveals that the plastic deformation generates large radial expansion, which is responsible for the transition from surface hoop compression to surface hoop tension that may induce surface crack during lithiation. We hope our effort can make a contribution to the understanding of stress-coupled kinetics in phase transformation electrodes.
基金financial support by the National Natural Science Foundation of China (No. 51364032)
文摘Billets of Mg-9Al-3Zn-1Mn-6Ca-2Nd alloy were produced by spray-deposition(the Osprey process).Effect of rolling deformation(T = 350?C, ε = 5%, 10%, and 15%, respectively) on microstructure and texture evolution of the Mg-9Al-3Zn-1Mn-6Ca-2Nd alloy was investigated by scanning electron microscopy(SEM), transmission electron microscopy(TEM) and X-ray diffraction(XRD). Results show that at pass reduction of ε = 5%, 10% and 15% at 350?C respectively, Mg-Nd-Zn typed 24R-LPSO structure was formed in(Ca, Nd)Al2phase(C15 Laves phase). With the increase in pass reduction(i.e. 5%, 10% and 15%), the texture pole density level of basal texture(0002) changed little and pyramidal texture(10 1ˉ3) were increased.In contrast, those of prismatic texture {101ˉ0} 〈11 2ˉ0〉 were increased initially and followed by a reduction, indicating texture randomization in the grain-refined Mg alloy. The combined contribution of LPSO phase and C15 phase was key to randomize the texture of the grain-refined Mg alloy. It was noted that the microcosmic plastic deformation of LPSO phase and nanometer-sized dispersed C15 phase impeded dislocation movement, led to dislocation tangles, and facilitated recrystallization.