NONLINEAR VIBRATION OF CIRCULAR SANDWICH PLATE UNDER THE UNIFORMED LOAD

The differential equations of the axisymmetric large amplitude free vibration for circular sandwich plates under static load are derived, and a set of nonlinearly coupled algebraic and differential eigenvalue equations of the problem are formulated following an assumed time mode approach suggested. The analytic solutions are presented and a relation for amplitude frequency-load of the plates with edge clamped is derived by modified iteration method. The effects of static load on vibrations of plates are investigated.

NON-LINEAR DYNAMIC BEHAVIOR OF THERMOELASTIC CIRCULAR PLATE WITH VARYING THICKNESS SUBJECTED TO NONCONSERVATIVE LOADING

The non-linear dynamic behaviors of thermoelastic circular plate with varying thickness subjected to radially uniformly distributed follower forces are considered. Two coupled non-linear differential equations of motion for this problem are derived in terms of the transverse deflection and radial displacement component of the mid-plane of the plate. Using the Kantorovich averaging method, the differential equation of mode shape of the plate is derived, and the eigenvalue problem is solved by using shooting method. The eigencurves for frequencies and critical loads of the circular plate with unmovable simply supported edge and clamped edge are obtained. The effects of the variation of thickness and temperature on the frequencies and critical loads of the thermoelastic circular plate subjected to radially uniformly distributed follower forces are then discussed.

BENDING SOLUTION OF A RECTANGULAR PLATE WITH ONE EDGE BUILT－IN AND ONE CORNER POINT SUPPORTED SUBJECTED TO UNIFORM LOAD

In this paper, using of the superposition principle. the bending solution ofrectangular plate with one edge built-in and one corner point supported subjected touniform load is derived. The results indicate the method has the advantages of rabidconvergence and high precision.

Experimental study on the stability of plate anchors in clay under cyclic loading

Although the bearing capacity of plate anchors in clay has been studied extensively, the results considering the effects of offshore cyclic loading are relatively rare. In the present study, 1g model tests are carried out to investigate the effect of cyclic loading on the bearing capacity of plate anchors in clay. The ultimate pullout capacity of plate anchors in clay decreases as the accumulated plastic shear strain grows due to the strain-softening of clay under cyclic loading. The load-displacement curves of these tests are presented and the effects of overburden stress and cyclic loading amplitude on the strain-softening behavior are discussed.

Axisymmetrical Nonlinear Bending and Buckling of a Circular Plate Under Large Load

With the terms of the exact series solution taken as trial functions, the method of point collocation was used to calculate the large deflection of a circular plate. The axisymmetrical bending formulae were developed for the calculation of a circular plate subjected to polynomial distributed loads, a concentrated load at the center, uniform radial forces and moments along the edge or their combinations. The support may be elastic. The buckling load was calculated. Under action of uniformly distributed load, central load or their compound load, solutions were compared with those obtained by other methods. Buckling beyond critical thrust was compared with that calculated by the power series method. The method presented in this paper has advantages of wide convergent range, high precision and short computing time. Moreover, the computing time is nearly independent of the complexity of the loads.

Nonlinear Resonance of the Rotating Circular Plate under Static Loads in Magnetic Field

The rotating circular plate is widely used in mechanical engineering, meanwhile the plates are often in the electromagnetic field in modern industry with complex loads. In order to study the resonance of a rotating circular plate under static loads in magnetic field, the nonlinear vibration equation about the spinning circular plate is derived according to Hamilton principle. The algebraic expression of the initial deflection and the magneto elastic forced disturbance differential equation are obtained through the application of Galerkin integral method. By mean of modified Multiple scale method, the strongly nonlinear amplitude-frequency response equation in steady state is established. The amplitude frequency characteristic curve and the relationship curve of amplitude changing with the static loads and the excitation force of the plate are obtained according to the numerical calculation. The influence of magnetic induction intensity, the speed of rotation and the static loads on the amplitude and the nonlinear characteristics of the spinning plate are analyzed. The proposed research provides the theory reference for the research of nonlinear resonance of rotating plates in engineering.

Nonlinear vibration and buckling of circular sandwich plate under complex load

The nonlinear vibration fundamental equation of circular sandwich plate under uniformed load and circumjacent load and the loosely clamped boundary condi- tion were established by von Karman plate theory, and then accordingly exact solution of static load and its numerical results were given. Based on time mode hypothesis and the variational method, the control equation of the space mode was derived, and then the amplitude frequency-load character relation of circular sandwich plate was obtained by the modified iteration method. Consequently the rule of the effect of the two kinds of load on the vibration character of the circular sandwich plate was investigated. When circumjacent load makes the lowest natural frequency zero, critical load is obtained.

THE ELASTO-PLASTIC STRAIN ANALYSIS OF NOTCHED PLATE UNDER CYCLIC LOADING—AN APPLICATION OF PLASTIC ANISOTROPIC HARDENING THEORY

In order to predict the life of engineering structures, it is necessary to investigate the strain distribution in notched members. In gineral, the Uauschinger Effect of materials under cyclic loading is not negligible, and so the anisolropic hardening model has been suggested. From the comparison between the calculated and experimental results in this paper, we can see that even the linear kinematic hardening model is quite suitable for strain analysis under cyclic loading.

BENDING OF CORNER-SUPPORTED RECTANGULAR PLATE UNDER CONCENTRATED LOAD

In this paper the solution for the bending of corner-supported rectangular plate under concentrated load at any point (α/2, η) of the middle line of the plate is given by means of a conception called modified simply supported edges and the method of superposition. Some numerical example is presented. The solution obtained by this method checks very nicely with what was obtained by G.T. Shih[3] by means of spline finite element method when η=d/2. This shows that this method of solution is satisfactory.

Lateral load-carrying capacity analyses of composite shear walls with double steel plates and filled concrete with binding bars

A method is developed to predict the lateral load-carrying capacity of composite shear walls with double steel plates and filled concrete with binding bars(SCBs). Nonlinear finite element models of SCBs were established by using the finite element tool, Abaqus. Tie constraints were used to connect the binding bars and the steel plates. Surface-to-surface contact provided by the Abaqus was used to simulate the interaction between the steel plate and the core concrete. The established models could predict the lateral load-carrying capacity of SCBs with a reasonable degree of accuracy. A calculation method was developed by superposition principle to predict the lateral load-carrying capacity of SCBs for the engineering application. The concrete confined by steel plates and binding bars is under multi-axial compression; therefore, its shear strength was calculated by using the Guo-Wang concrete failure criterion. The shear strength of the steel plates of SCBs was calculated by using the von Mises yielding criterion without considering buckling. Results of the developed method are in good agreement with the testing and finite element results.

ON THE LIAPUNOV’S STABILITY OF A CLAMPED ORTHOTROPIC ROUND PLATE UNDER RADIAL AXISYMMETRICAL IMPACTLOAD

Liapunov's 2nd method is applied to analyse the Stability of a ciamped poleorthotropic round plate acted by a radial axisymmetrical impact load on its periphery. The analysis is carried cut under the assumptions of small deflection and elasticity The impact load is supposed to have a step impulsive form. A sufficient stability condition is given.

Experimental study on the wave loads of twin-plate breakwaterunder oblique waves

In this study, systematic physical model tests were performed to investigate the wave forces on the twin-plate breakwater under irregular waves. Based on the experimental results, the effects of the relative plate width B/L,wave height Hs/D and incident angle θ0 on the wave forces were analyzed and discussed. The results showed that:(1) The envelopes of the total wave pressure were generally symmetrical along the direction of plate width under the incident angles(θ0) being 0°, 15°, 30°, 45° and 60°. In particular, the envelopes of wave pressure atθ0=30° were larger than all other cases.(2) The synchronous pressure distribution of the breakwater under oblique wave action was more complicated comparing to the normal incident waves.(3) Based on data analysis, an empirical formula was obtained to estimate the total vertical force of the twin-plate breakwater.This empirical formula can be a good reference for the design basis of engineering applications under specified wave conditions.

Comparison Between Two Solutions Based on the Relationship of Load-deflection Character of a Large Deflection Rubber Circular Plate

The rubber circular plate is considered as a kind of membrane. Based on the character that there exists no bending moment inside a membrane, the geometric behavior of the rubber circular plate in expanding state was described with the aid of a group of mathematic method. The relationship between deflection and load was attained by means of calculating stress and strain inside the curved surface of rubber plate. Meantime, based on Hencky method, the relationship between deflection and load was attained and considered as the Hencky solution. The different results given rise by the two different resolving methods were compared. The deviation results from the Hencky method was discussed, and a kind of correcting method was put forward.

Static load test and load transfer mechanism study of squeezed branch and plate pile in collapsible loess foundation

As a special geological phenomenon, the character of collapsible loess foundation is collapsible when penetrated by water. This character leads to the soil losing load bearing capacity largely and may lead to foundation failure. Pile is a popular foundation used in collapsible loess. The squeezed branch and plate pile is a new type of pile developed in recent years and has not be used in a project before. In this paper three squeezed branch and plate piles are tested in collapsible loess after immersion processing. The results may be used for reference in similar construction project, and to provide theoretical references for de- signing of the squeezed branch and plate piles in engineering practice.

AXISYMMETRIC BENDING FOR THICK LAMINATED CIRCULAR PLATE UNDER A CONCENTRATED LOAD

Based upon the fundamental equations of three dimensional elasticity, the state equation for axisymmetric bending of laminated transversely isotropic circular plate is established and the concentrated force on plate surface is expanded into Fourier_Bessel's series, therefore, an analytical solution for the problem is presented. Every fundamental equation of three dimensional elasticity can be exactly satisfied by the solution and all the independent elastic constants can be taken into account fully, furthermore, the continuity conditions between plies can also be satisfied.

ANALYSIS OF SHAKEDOWN OF FG BREE PLATE SUBJECTED TO COUPLED THERMAL-MECHANICAL LOADINGS

The static and kinematic shakedown of a functionally graded （FG） Bree plate is analyzed. The plate is subjected to coupled constant mechanical load and cyclically varying temperature. The material is assumed linearly elastic and nonlinear isotropic hardening with elastic modulus,yield strength and the thermal expansion coeffcient varying exponentially through the thickness of the plate. The boundaries between the shakedown area and the areas of elasticity,incremental collapse and reversed plasticity are determined,respectively. The shakedown of the counterpart made of homogeneous material with average material properties is also analyzed. The comparison between the results obtained in the two cases exhibits distinct qualitative and quantitative difference,indicating the importance of shakedown analysis for FG structures. Since FG structures are usually used in the cases where severe coupled cyclic thermal and mechanical loadings are applied,the approach developed and the results obtained are significant for the analysis and design of such kind of structures.

NONLINEAR VIBRATION OF CIRCULAR SANDWICH PLATES UNDER CIRCUMJACENT LOAD

Based on von Karman plate theory, the issue about nonlinear vibration for circular sandwich plates under circumjacent load with the loosely clamped boundary condition was researched. Nonlinear differential eigenvalue equations and boundary conditions of the problem were formulated by variational method and then their exact static solution can be got. The solution was derived by modified iteration method, so the analytic relations between amplitude and nonlinear oscillating frequency for circular sandwich plates were obtained. When circumjacent load makes the lowest natural frequency zero, critical load is obtained.

LARGE DEFLECTION PROBLEM OF CIRCULAR PLATES WITH VARIABLE THICKNESS UNDER THE ACTION OF COMBINED LOADS

By using the modified iteration method of large deflection theory of plates with variable thichness[1], we solve the problem of circular plates with variable thickness subjected to combined loads under the boundary conditions of the clamped edges and get comparatively more accurate second-order approximate analytical solution. If the results of this paper are degraded into the special cases, the results coinciding with those of papers [1,2] can be obtained. In this paper, the characteristic curves are plotted and some comparisons are made. The results of this paper are satisfactory.

Effect of electrode Pt-loading and cathode flow-field plate type on the degradation of PEMFC

The electrode Pt-loading has an effect on the number of active sites and the thickness of catalyst layer,which has huge influence on the mass transfer and water management during dynamic process in PEMFCs. In this study, membrane electrode assemblies with different Pt-loadings were prepared, and PEMFCs were assembled using those membrane electrode assemblies with traditional solid plate and water transport plate as cathode flow-field plates, respectively. The performance and electrochemical surface area of cells were characterized to evaluate the membrane electrode assemblies degradation after rapid currentvariation cycles. Scanning electron microscope and transmission electron microscope were used to investigate the decay of catalyst layers and Pt/C catalyst. With the increase of Pt-loading, the performance degradation of membrane electrode assemblies will be mitigated. But higher Pt-loading means thicker catalyst layer, which leads to a longer pathway of mass transfer, and it may result in carbon material corrosion in membrane electrode assemblies. The decay of Pt/C catalyst in cathode is mainly caused by the corrosion of carbon support, and the degradation of anode Pt/C catalyst is a consequence of migration and aggregation of Pt particles. And using water transport plate is beneficial to alleviating the age of cathode Pt/C catalyst.