Lateral clavicle fracture-plating options and considerations

Clavicle fractures are among the most prevalent types of fractures with numerous treatment strategies that have evolved over time.In the realm of lateral-third clavicle fracture management,several surgical methods are available,with plate and screw constructs being one of the most frequently employed options.Within this construct,numerous choices exist for fixing the fracture.This editorial provides an overview of the common plate options utilized in the management of distal third clavicle fractures underscoring the critical considerations and approaches that guide clinicians in selecting the most appropriate fixation techniques,considering the complex landscape of clavicle fractures and their challenging management.

The principle and amelioration of lithium plating in fast-charging lithium-ion batteries

Fast charging is restricted primarily by the risk of lithium(Li)plating,a side reaction that can lead to the rapid capacity decay and dendrite-induced thermal runaway of lithium-ion batteries(LIBs).Investigation on the intrinsic mechanism and the position of Li plating is crucial to improving the fast rechargeability and safety of LIBs.Herein,we investigate the Li plating behavior in porous electrodes under the restricted transport of Li^(+).Based on the theoretical model,it can be concluded that the Li plating on the anodeseparator interface(ASI)is thermodynamically feasible and kinetically advantageous.Meanwhile,the prior deposition of metal Li on the ASI rather than the anode-current collector interface(ACI)is verified experimentally.In order to facilitate the transfer of Li^(+)among the electrode and improve the utilization of active materials without Li plating,a bilayer asymmetric anode composed of graphite and hard carbon(GH)is proposed.Experimental and simulation results suggest that the GH hybrid electrode homogenizes the lithiated-rate throughout the electrode and outperforms the pure graphite electrode in terms of the rate performance and inhibition of Li plating.This work provides new insights into the behavior of Li plating and the rational design of electrode structure.

Formation mechanism of electroless plating nickel-based composite coating on highly active rare earth magnesium alloys and its corrosion resistance and adhesion performance

The process of preparing anodic oxide film containing active sites and electroless nickel plating on highly active rare earth magnesium alloy was developed.The formation mechanism of electroless nickel plating on active anodic oxide film and the structure and properties of the composite coating were studied by several surface and electrochemical techniques.The results showed that Ag nanograins with an average size of 10 nm were embedded into the anodic oxide film with pores of 0.1−2μm.Ag nanoparticles provided a catalytic site for the deposition of Ni-B alloy,and the Ni crystal nucleus was first grown in horizontal mode and then in cylindrical mode.The corrosion potential of the composite coating increased by 1.37 V and the corrosion current reduced two orders of magnitude due to the subsequent deposition of Ni-P alloy.The high corrosion resistance was attributed to the misaligning of these micro defects in the three different layers and the amorphous structure of the Ni-P alloy in the outer layer.These findings provide a new idea for electroless nickel plating on anodic oxide film.

Early Treatment Outcome of Humeral Shaft Fracture Non-Union in Adults: Comparative Study of Plating versus Interlocking Nailing

Background: Fractures of humeral shaft in adults are common injuries. Humeral shafts non-union either from late presentation after initial treatment by traditional bone setters or failed non-operative orthodox care is a major problem in this part of the world. This non-union is a major treatment challenge with increased cost of care and morbidity in this part of the world. Humeral shaft non-union can be treated with locked intra-medullary nailing (LIMN) or dynamic compression plating (DCP). Study on comparison of these methods of fixation in this part of the world is scarce in literature search, hence the reason for this study. Objective: The objectives of this study are: (1) to compare early clinical outcome following fixation of humeral shaft fracture nonunion with DCP versus LIMN;(2) to compare the time of radiologic fracture union of DCP with LIMN;(3) to compare complications following fixation of humeral shaft fracture nonunion with DCP versus LIMN. Patients and Methods: This was a randomized control study done for 2 years in which fifty adult patients with humeral shaft non-union were recruited. The patients were grouped into 2 (P = DCP & N = LIMN). Forty five of the patients completed the follow up periods of the study and then analyzed. The P group had ORIF with DCP while the N group had ORIF with LIMN. Both groups had grafting with cancellous bones. Each patient was followed up for a period of 6 months at the time which radiographic union is expected. Any patient without clinical and/or radiographic evidence of union after six months of surgery was diagnosed as having recurrent non-union. The data generated was analyzed using SPSS Version 23. The results were presented in charts and tables. The paired t-test was used while considering p value Result: Forty five patients completed follow up. There was a male preponderance (4:1), right humerus predominated (3:2). Motor vehicular accidents were the commonest cause of the fractures (62%). Most non-union fractures occurred at the level of the middle 3rd of the humeral shaft (60%). Failed TBS treatment was the commonest indication for the osteosynthesis (71%). More patients had plating (53%) compared to 47% who had LIMN. Most patients (93.4%) had union between 3 to 6 months irrespective of fixation type with no significant statistical difference between the union rate of DCP and LIMN (p value 0.06) with similar functional outcome and complication rates irrespective of the type of fixation. Conclusion: This study showed that the success rates in term of fracture union, outcome functional grades and complication rates were not directly dependent on the types of the fixation: plating or locked intra-medullary nailing.

Microstructure and mechanical properties of TiN/TiAlN multilayer coatings deposited by arc ion plating with separate targets

TiN/TiAlN multilayer coatings were prepared by arc ion plating with separate targets. In order to decrease the unfavorable macroparticles, a straight magnetized filter was used for the low melting aluminium target. The results show that the output plasmas of titanium target without filter and aluminium target with filter reach the substrate with the same order of magnitude. Meanwhile, the number of macropartieles in TiN/TiAlN multilayer coatings deposited with separate targets is only 1/10-1/3 of that deposited with alloy target reported in literature. Al atom addition may lead to the decrease of peak at （200） lattice plane and strengthening of peak at （111） and （220） lattice planes. The measured hardness of TiN/TiAlN multilayer coatings accords with the mixture principle and the maximum hardness is HV2495. The adhesion strength reaches 75 N.

Electroless Ni-P plating on Mg-Li alloy by two-step method

Pretreated Mg-Li alloy sheets were pre-plated in a NiCO3？2Ni（OH）2？4H2O solution to form a thin Ni-P alloy film and then plating in a NiSO4？6H2O solution was carried out to obtain a protective coating.The surface morphology,structure and corrosion resistance of the coating were studied.The results showed that a flat,bright and compact plating layer,which was integrated into the matrix metal,was obtained.The P content of the Ni-P coating reached 13.56%（mass fraction）.The hardness value of the Ni-P coating was about HV 549.The polarization curve showed that the corrosion potential of the Ni-P coating reached ？0.249 V（vs SCE）.A long passivation region was found on the polarization curve,and this phenomenon indicated that the coating has an excellent anti-corrosion property.

Structure and effects of electroless Ni-Sn-P transition layer during acid electroless plating on magnesium alloys

An electroless ternary Ni-Sn-P transition layer with high corrosion resistance was applied for acid electroless nickel plating on magnesium alloys. The surface morphologies and microstructure of the traditional alkaline electroless Ni-P and novel Ni-Sn-P transition layers were compared by SEM and XRD, and the bonding strengths between the transition layers and AZ31 magnesium alloys were tested. The corrosion resistance of the samples was analyzed by porosity test, potentiodynamic polarization, electrochemical impedance spectroscopy（EIS） in acid electroless solution at p H 4.5 and immersion test in 10% HCl. The results indicate that the transition layer is essential for acid electroless plating Ni-P coatings on magnesium alloys. Under the same thin thickness（-6 μm）, the electroless Ni-Sn-P transition layer possesses superior properties to the traditional Ni-P transition layer, including high amorphization, smooth and dense surface without pores, enhanced bonding strength and corrosion resistance. Most importantly, acid electroless Ni-P coatings can be successfully deposited on magnesium alloys by using Ni-Sn-P transition layer.

Effect of immersion Ni plating on interface microstructure and mechanical properties of Al/Cu bimetal

A nickel-based coating was deposited on the pure Al substrate by immersion plating,and the Al/Cu bimetals were prepared by diffusion bonding in the temperature range of 450-550 ℃.The interce microstructure and fracture surface of Al/Cu joints were studied by scanning electron microscopy（SEM） and X-ray diffraction（XRD）.The mechanical properties of the Al/Cu bimetals were measured by tensile shear and microhardness tests.The results show that the Ni interiayer can effectively eliminate the formation of Al-Cu intermetallic compounds.The Al/Ni interface consists of the Al3Ni and Al3Ni2 phases,while it is Ni-Cu solid solution at the Ni/Cu interce.The tensile shear strength of the joints is improved by the addition of Ni interiayer.The joint with Ni interiayer annealed at 500 ℃ exhibits a maximum value of tensile shear strength of 34.7 MPa.

Over-plating工艺过程的变网格数值模拟(英文)

考察了over-plating工艺中不同线距、线宽条件下的电沉积规律。利用数值模拟方法对图形结构轮廓和电沉积速度之间的相互影响进行了分析,同时采用变网格方法来适应电沉积过程中结构轮廓的不断变化。数值模拟结果表明:当线距/线宽较大( >12)时,相邻图形的电沉积速度受到的影响很小,图形的横向和纵向的电沉积速度逐渐趋于一致;而当线距/线宽较小( <6)时,相邻电沉积图形之间相互影响显著,线距/线宽越小,纵向电沉积速度和横向电沉积速度之比越大,因此相邻电沉积图形中间区域可能产生空洞,从而出现电镀缺陷的情形。对于上述工艺缺陷,可以通过增加辅助导电层进行消除,实验结果表明效果良好。

A New Activation Method for Electroless Metal Plating: Palladium Laden via Bonding with Self-Assembly Monolayers

A new activation method has been developed for electroless copper plating on silicon wafer based on palladium chemisorption on SAMs of APTS without SnCl2 sensitization and roughening condition. A closely packed electroless copper film with strong adhesion is successfully formed by AFM observation. XPS study indicates that palladium chemisorption occurred via palladium chloride bonding to the pendant amino group of the SAMs.

XPS AND UPS STUDIES OF THE INTERFACIAL INTERACTION IN Ni ZrO 2 COMPOSITE PLATING

The interfacial interaction existing in the Ni ZrO 2 composite plating has been investigated. The experimental results show that no new phases were formed in the interfacial regions between matrix Ni and ZrO 2 particles, but an orbital interaction through the mutual overlap of the d orbits does exist in the interfacial regions between Ni atoms and Zr 3+ ions.

Study on Misplating Problems of Composed of Wool and Lycra Plated Knitted Fabrics

By a great deal of experiments,the misplating problemsof plated knitted fabrics composed of wool and Lycra arediscussed and analyzed.The factors affecting the mis-plating problems on manually operated flat knitting ma-chine include the construction and adjustment of a plat-ing feeder,wool yarn count,feeding tension,takedowntension and the ground fabric structures.Some usefulresults can be derived from these works.

Electroless plating and growth kinetics of Ni-P alloy film on SiC_p/Al composite with high SiC volume fraction

After Sn/Pd activating, the SiCp/Al composite with 65% SiC (volume fraction) was coated by electroless Ni?P alloy plating. Surface morphology of the composite and its effect on the Ni?P alloy depositing process and bonding action of Ni and P atoms in the Ni?P alloy were studied. The results show that inhomogeneous distribution of the Sn/Pd activating points results in preferential deposition of the Ni?P alloy particles on the Al alloy and rough SiC particle surfaces and in the etched caves. The Ni?P alloy film has an amorphous structure where chemical bonding between Ni and P atoms exists. After a continuous Ni?P alloy film formed, electroless Ni?P alloy plating is not affected by surface morphology and characteristics of the SiCp/Al composite any longer, but by the electroless plating process itself. The Ni?P alloy film follows linear growth kinetics with an activation energy of 68.44 kJ/mol.

Ion-Conductive-Polymer-Film Actuators with Pt Electrodes Selectively Grown using Non-Electrolyzed Plating

Organic soft actuators are of special interest in many fields including intravascular neurosurgery. Ion conductive polymer film （ICPF） actuators have been one of the strong candidates. The ICPF investigated here was a cation-exchange membrane （Nation 117, Du Pont）. When a voltage is given between the metal eIectrodes of an ICPF actuator, the ICPF actuator bends in the water due to the motion of Li＋ cations with associated water. In order to increase the freedom of the deformation of the ICPF actuator, structures of independent electrode pairs were proposed. The electrodes were selectively deposited by non-electrokvzed plating including the Pt [（NH3）6]^4＋ deposition process in a [Pt（NH3）6]Cl4 solution and the reduction process in a NaBH4 solution. Here, an elastomer adhesive tape with a fine electrode patterns was used performances were reported in detail. as a mask. The actuators processing conditions and their actuator

Plates, Beams and Shells Reinforced by CNTs or GPLs: A Review on Their Structural Behavior and Computational Methods

Since the initial observation of carbon nanotubes(CNTs)and graphene platelets(GPLs)in the 1990 and 2000s,the demand for high-performance structural applications and multifunctional materials has driven significant interest in composite structures reinforced with GPLs and CNTs.Incorporating these nanofillers into matrix materials markedly enhances the mechanical properties of the structures.To further improve efficiency and functionality,func-tionally graded(FG)distributions of CNTs and GPLs have been proposed.This study presents an extensive review of computational approaches developed to predict the global behavior of composite structural components enhanced with CNT and GPL nanofillers.The analysis focuses on key structural elements,such as plate-type configurations,cylindrical and curved shells,and beams,emphasizing the computational techniques utilized to simulate their mechanical behavior.The utilization of three-dimensional elasticity theories and equivalent single-layer(ESL)frameworks,which are widely employed in the modeling and analysis of these composites,is comprehensively discussed.Additionally,the paper examines various mechanical performance aspects,including static,buckling,post-buckling,vibrational,and dynamic responses for the mentioned structures.The unique features of hybrid nanocomposites,combining CNTs and GPLs,are also analyzed.Furthermore,the study delves into the fabrication and processing techniques of these materials,with a particular focus on strategies to mitigate nanofiller agglomeration.The review extends to cover thermal and electrical properties,durability under environmental exposure,fatigue resistance,and vibration-damping characteristics.In conclusion,the paper underscores the necessity for ongoing advancements in computational modeling to facilitate improved design,analysis,and optimization of nanocomposite structures.Future research opportunities in this rapidly advancing domain are also outlined.

Propagating subduction initiation of the Caroline Plate at the Mussau Trench

New seismic imaging from the Mussau Trench confirms that,under horizontal compression on an oceanic plate boundary,it is within the young and weak oceanic plate that a trench will develop,and it is the young plate,not so long after its birth,that starts to subduct toward the old plate.The Mesozoic Pacific Plate cannot easily bend,under the joint horizontal compression and vertical gravity pull,even with a pre-existing weak zone in place and with a large age offset across the plate boundary.The bending of the Caroline Plate near the northern end of the Mussau Trench started only after a long-time span of trench migration,and/or after a prolonged transition from initial compression to trench development.Highly contrasting trench deformation and sedimentary accretion between two parallel seismic sections support an evident migration of underthrusting or significant longitudinal heterogeneity along the trench.The swift transition from underthrusting to non-thrusting can be explained by a counter-clockwise rotation of the Caroline Plate.That miniature accretionary wedges develop even before the subduction initiates imply strong compression and uplifting before the underthrusting can kick-start.Rotation of the Caroline Plate have been halted as the Mussau Trench is seismically rather quiet and the Lyra Trough to the east shows relaxational extension.

Tectonic modes of mantle convection and their implications for Earth's tectonic evolution based on three-dimensional numerical simulations

Five tectonic modes of mantle convection are obtained and analyzed with three-dimensional numerical models in a spherical shell domain.The five tectonic convective modes are non-plate mobile-lid,plate-like mobile-lid,episodic plate-like mobile-lid,episodic stagnant-lid,and stagnant-lid convective modes,respectively.The typical characteristics of these five tectonic modes and their numerical classification criteria based on plateness,mobility,and their standard deviations are presented and discussed.The results show that the yield stress of the lithosphere has profound effects on the tectonic convective modes.With the gradual increase of yield stress,the tectonic mode of mantle convection changes from one to another sequentially through the aforementioned five modes.Additionally,as the Rayleigh number increases,the range of yield stress for the platelike mobile-lid convective mode decreases,and the dimensionless transition stress between different tectonic modes increases.Specifically,the dimensional transition stress between the non-plate mobile-lid convective mode and plate-like mobile-lid convective mode increases with the increase of Rayleigh number,but decreases between other tectonic modes.Furthermore,we find that the transition stress between different tectonic modes is inversely proportional to the internal heating rate,with the transition stress decreasing as the internal heating rate increases.The fitting analysis of the transition stress between tectonic modes shows that Earth's current plate tectonics correspond to a lithospheric yield stress of 150–250 MPa,which aligns with the strength of serpentinized mantle rock determined by experimental petrography.If the Archean mantle was 300℃warmer than it is today,then the Earth was in an episodic stagnant-lid convective mode.The tectonic evolution of the Earth's surface is closely related to the lithospheric strength and the process of thermal evolution.If the lithospheric strength was only 150 MPa,plate tectonics in the early mantle rapid cooling model would have begun before 3.8 Ga,and plate tectonics in the late mantle rapid cooling model would have begun at approximately 1.5 Ga.However,at a lithospheric strength of 200 MPa,plate tectonics in the late mantle rapid cooling model would have begun later than 0.95 Ga,and plate tectonics in the early mantle rapid cooling model would have begun at approximately 2 Ga.The early Earth was in the episodic stagnant-lid convective mode,which means that subduction might still have occurred at that time.The presence of the episodic plate-like mobile-lid convective mode in Earth's later history indicates that there might also have been intermittent surface stagnation during plate tectonics,which may provide an explanation for the quiet period of tectonic activity at approximately 1.0 Ga on Earth.This indicates that tectonic inactivity during a geological period is not an indicator that plate tectonics did not begin.

Homogenization pretreatment and electroless Ni-P plating on AZ91D magnesium alloy

Electroless nickel plating on AZ91D substrate with a new and eco-friendly pretreatment process based on tuning an electrochemical homogeneous surface was investigated. The morphology, deposition process, chemical composition and microstructure of Ni-P coating were studied. It is indicated that β phases are selectively removed, producing a microstructural homogeneous surface and the subsequent uniform and compact Zn immersion layer. A defect-free and well adhesive Ni-P coating can be successfully obtained due to its uniform nucleation and growth based on such pretreatment. Potentiodynamic polarization and electrochemical impedance spectroscopy （EIS） tests reveal that Ni-P coating could significantly improve the corrosion resistance of AZ91D substrate.

Recovery of Copper（II） and Nickel（II） from Plating Wastewater by Solvent Extraction

The solvent extraction technology, was applied to recover Cu^2＋ and Ni^2＋ from plating wastewater.Lix984N was chosen as the extractant due to-its gooff extraction performance. The influence parame-ters were examlned. The results show that the separation of Cu^2＋ and Ni＂ from sulphate medium can be realized by adjusting pH value with the help of Lix984N. For extracting Cu^2＋ and Ni^2＋, the optimal pH values are 4 and 10.5, and the maximal extraction percentages are 92.9% and 93.0%, respectively .With recovered Cu^2＋ and Ni^2＋ stripped in 170g.L^ -1 and 200 g.L^-1 H2SO4 medium, the stripping percentages of Cu^2＋ and Ni^2＋ are 92.9% and 93.0%, respectively. This method is simple and can be used to recover Cu^2＋ and Ni^2＋ from plating wastewater. And a flow sheet for separation of Cu^2＋ and Ni^2＋ is presented.

Ti/(Ti,Cr)N/CrN multilayer coated 316L stainless steel by arc ion plating as bipolar plates for proton exchange membrane fuel cells

Arc ion plating (AIP) is applied to form Ti/(Ti,Cr)N/CrN multilayer coating on the surface of 316L stainless steel (SS316L) as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The characterizations of the coating are analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Interfacial contact resistance (ICR) between the coated sample and carbon paper is 4.9 m Omega cm(2) under 150 N/cm(2), which is much lower than that of the SS316L substrate. Potentiodynamic and potentiostatic tests are performed in the simulated PEMFC working conditions to investigate the corrosion behaviors of the coated sample. Superior anticorrosion performance is observed for the coated sample, whose corrosion current density is 0.12 mu A/cm(2). Surface morphology results after corrosion tests indicate that the substrate is well protected by the multilayer coating. Performances of the single cell with the multilayer coated SS316L bipolar plate are improved significantly compared with that of the cell with the uncoated SS316L bipolar plate, presenting a great potential for PEMFC application. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.