Assessment of Point and Nonpoint Sources Pollution in Songhua River Basin,Northeast China by Using Revised Water Quality Model

Individual participation of pollutants in the pollution load should be estimated even if roughly for the appropriate environmental management of a river basin.It is difficult to identify the sources and to quantify the load, especially in modeling nonpoint source.In this study a revised model was established by integrating point and nonpoint sources into one-dimensional Streeter-Phelps(S-P) model on the basis of real-time hydrologic data and surface water quality monitoring data in the Jilin Reach of the Songhua River Basin.Chemical oxygen demand(COD) and ammonia nitrogen(NH 3-N) loads were estimated.Results showed that COD loads of point source and nonpoint source were 134 958 t/yr and 86 209 t/yr, accounting for 61.02% and 38.98% of total loads, respectively.NH 3-N loads of point source and nonpoint source were 16 739 t/yr and 14 272 t/yr, accounting for 53.98% and 46.02%, respectively.Point source pollution was stronger than nonpoint source pollution in the study area at present.The water quality of upstream was better than that of downstream of the rivers and cities.It is indispensable to treat industrial wastewater and municipal sewage out of point sources, to adopt the best management practices to control diffuse pollutants from agricultural land and urban surface runoff in improving water quality of the Songhua River Basin.The revised S-P model can be successfully used to identify pollution source and quantify point source and nonpoint source loads by calibrating and validating.

Numerical Calculation of Seafloor Synthetic Seismograms Caused by Low Frequency Point Sound Source

Elastic wave on seafloor caused by low frequency noise radiated from ship is called ship seismic wave which can be used to identify ship target. In order to analyze the wave components and the propagating properties of ship seismic wave, the numerical calculation of synthetic seismograms on seafloor aroused by a low frequency point sound source is carried out using a wave number integration technique combined with inverse Fourier transform. According to the numerical example of hard seafloor, the time series of seismic wave on seafloor are mostly composed of interface waves and normal mode waves. Each normal mode wave has a well defined low cut-off frequency, while the interface wave doesn't have. The frequency dispersion of normal mode wave is obvious when frequency is lower than 100Hz, while the interface wave is dispersive only in the infra-sound frequency range. The time series of seismic wave is dominated by the interface wave when the source frequency is less than the minimal cut-off frequency of normal mode wave.

Three-dimensional steady-state closed form solution for multilayered fluid-saturated anisotropic finite media due to surface/internal point source

A three-dimensional(3 D)steady-state solution of fluid saturated anisotropic finite media is presented.The eigenequation method and the pseudo-Stroh formalism are used to obtain the exact solution for homogeneous saturated finite media.The propagator matrix method is introduced to deal with the corresponding multilayered poroelastic media.The poroelastic solutions due to surface or internal point fluid source are obtained.The comparison of the results of the saturated isotropic media in a half space and those obtained by the finite element method is given to illustrate the accuracy of the solution in a finite domain.Numerical solutions of a sandwich poroelastic medium are presented to analyze its hydromechanical behaviors.Two ratios of the horizontal permeability to vertical permeability and different source positions are investigated.The results show that the fluid parameters and source positions have great influence on the hydromechanical behaviors of the layered media.

Evaluation of Red Blood Cell Contribution to Platelet Activation in the Bulk Applying Red Blood Cell—Platelet Thrombus as a Point Source Model

In this study, a point source mathematical model is proposed to describe the diffusion of adenosine di-phosphate (ADP) from either damaged red blood cell (RBC) or activated platelet. The convective diffusion equation is reduced to describe the suggested problem. The final differential equation is solved using Laplace transforms and ADP concentration profiles around the source are obtained. Thrombi of 5 to 20 μm3 containing platelets and a range of red blood cells (RBCs) (0%, 25%, 50%, 75%, 100%) concentrations are used to apply the model. Reported ADP concentrations in the literature are used and its dynamic release from the point source is calculated. Results suggest that RBC chemical contribution to platelet aggregation in the bulk is much less than that of platelet (almost) negligible. However, the physical effect of RBCs is dominant in the bulk through augmentation of released ADP and platelets diffusivities. Moreover, the chemical contribution reported in previous studies is suggested to be as a result of interaction of RBC with the surface under the influence of shear stresses in the boundary region.

FLOW PROPERTIES OF A DUSTY-GAS POINT SOURCE IN A SUPERSONIC FREE STREAM

By using Lagrangian method, the flow properties of a dusty-gas point source in a supersonic free stream were studied and the particle parameters in the near-symmetry-axis region were obtained . It is demonstrated that fairly inertial particles travel along oscillating and intersecting trajectories between the bow and termination shock waves . In this region, formation of ' mufti- layer structure' in panicle distribution with alternating low- and high density layers is revealed. Moreover, sharp accumulation of particles occurs near the envelopes of particle trajectories .

CONCENTRATION DISTRIBUTION OF FRACTIONAL ANOMALOUS DIFFUSION CAUSED BY AN INSTANTANEOUS POINT SOURCE

The Fox function expression and the analytic expression for the concentration distribution of fractional anomalous diffusion caused by an instantaneous point source in n-dimensional space (n= 1, 2 or 3) are derived by means of the condition of mass conservation , the time-space similarity of the solution , Mellin transform and the properties of the Fox function . And the asymptotic behaviors for the solutions are also given .

Simulation and analysis of point-source surface wave fields

The complexity of near surface intensifies the diversity of seismic wave fields, which makes study on near surface wavefields important in many aspects. The strong absorption of low velocity layer can affect the resolution of seismic data, and free boundary can cause surface wave. Considering the above problems, we focus on the Rayleigh wavefields simulation using finite-difference wave equation of higher-order staggered grids and PML boundary conditions. Free boundary, buried source and overlying low velocity layer are taken into consideration and point explosion source is adopted. Through some numerical simulation with different parameters, we quantitatively analyze relationship between wave intensity and source depth, as well as the energy variation with propagation and obtain some practical knowledge and conclusions.

Development of point source method and its practical significance

The advantages of Reichardt＇s hypothesis in dealing with single and multiple circular jets in a stagnant environment are highlighted. The stages involved in the development of the point source method, an offshoot of the new hypothesis, are presented, Previous results of experiments on multiple circular jets in a stagnant environment justify the method of superposition. As a prelude to discussion of multiple jets in a co-flowing stream, results on the excess-velocity decay, the growth of the shear layer, and the dilutions for a single jet based on Reichardt＇s hypothesis are presented. The spreading hypothesis is generalized by introducing a link factor kl to account for the co-flowing stream. The distribution of excess-momentum flux uAu is shown to be Gaussian in nature. Based on the principle of superposition, the decay of the maximum excess velocity and the dilution are predicted for odd and even numbers of jets in an array. The predictions seem to be in good agreement with observed data.

Distributional Relations on Impulse Radiating Surface and Point Type Sources

The electromagnetic field relations are demonstrated on impulse radiating surface and point type sources, which are characterized by first and second order singularities at rest in a Schwartz-Sobolev space setting. The investigation starts with a general introduction to Schwartz-Sobolev distributions, the electromagnetic field equations and various modes of impulsive radiation. This is followed by an outline of temporal distributional relations in arbitrary media and distributional derivative operations on an arbitrary regular surface, all of which are employed in an investigation of impulse radiation mechanism on single and double layer sources. Similar steps are followed in a description of point distributions and investigation of impulse radiation mechanism on electric and magnetic point dipoles.

Cross-Correlation Detection of Point Sources in the WMAP First Year Data

We apply a Cross-Correlation （CC） method developed previously for detecting gamma-ray point sources to the WMAP first year data by using the Point-Spread Function of WMAP and obtain a full sky CC coefficient map. We find that the CC method is a powerful tool to examine the WMAP foreground residuals which can be further cleaned accord- ingly. Evident foreground signals are found in the WMAP foreground cleaned maps and the Tegmark cleaned map. In this process 101 point sources are detected, and 26 of them are new sources additional to the originally listed WMAP 208 sources. We estimate the flux of these new sources and verify them by another method. As a result, a revised mask file based on the WMAP first year data is produced by including these new sources.

THEORETICAL ANALYSIS ON THE AUTOPLOIDY BETWEEN THE TWELVE YUAN (SOURCE) POINTS AND THEIR CORRESPONDING ZANGFU-ORGANS

In the present paper, the authors make a theoretical analysis on the autoploidy between the twelve Yuan （source） points and their corresponding Zangfu-organs from 1 ） historical development, 2） correlation, 3） clinical application, 4） experimental research results about the relationship between Yuan points and the Zangfu-organs, and between meridians and Zangfu-organs, and 5） literature description. The twelve Yuan points have an important role in clinical diagnosis and treatment of diseases, and a close association with the Zangfu-organs.

Optical Design and Stray Light Analysis of the Space Infrared Optical System

This article describes a novel configuration design for a re-imaging off-axis catadioptric space infrared optical system,and in order to satisfy the signal noise ratio requirements of the system,the stray light of the system is necessary to analyze and restrain. The optical system with a focal length of 1 200 mm,an entrance pupil diameter of 600 mm,an F-number of 2,a field of view of 3°× 0. 15°,a working wave band of 8 μm-10 μm,and the image quality of the optical system almost approach to diffraction limits in all field of view.Then the mathematical models of stray light are built,and the suppressive structure is established to eliminate the effect of stray light. Finally,TraceP ro is used to analyze and simulate stray light with and without the suppressive structure,and also get the results of the PST curves. The results indicate that appropriate optical system and suppressive structure can highly reduce the stray light of the space infrared optical system.

An Optical Fractional Fourier Transform System

An alternative way to perform fractional Fourier transform is proposed. The system is illuminated by a divergent beam. It has one more degree of freedom in arrangement than the previous system. Mathematically, the choice of focal length of one of the two lenses depends on an easily adjustable parameter which determines the location of illuminating point source.

A land use regression model incorporating data on industrial point source pollution

Advancing the understanding of the spatial aspects of air pollution in the city regional environment is an area where improved methods can be of great benefit to exposure assessment and policy support. We created land use regression （LUR） models for SO2, NO2 and PMI0 for Tianjin, China. Traffic volumes, road networks, land use data, population density, meteorological conditions, physical conditions and satellite-derived greenness, brightness and wetness were used for predicting SOa, NO2 and PMt0 concentrations. We incorporated data on industrial point sources to improve LUR model performance. In order to consider the impact of different sources, we calculated the PSIndex, LSIndex and area of different land use types （agricultural land, industrial land, commercial land, residential land, green space and water area） within different buffer radii （1 to 20 kin）. This method makes up for the lack of consideration of source impact based on the LUR model. Remote sensing-derived variables were significantly correlated with gaseous pollutant concentrations such as SO2 and NO2. R2 values of the multiple linear regression equations for SO2, NO2 and PM10 were 0.78, 0.89 and 0.84, respectively, and the RMSE values were 0.32, 0.18 and 0.21, respectively. Model predictions at validation monitoring sites went well with predictions generally within 15% of measured values. Compared to the relationship between dependent variables and simple variables （such as traffic variables or meteorological condition variables）, the relationship between dependent variables and integrated variables was more consistent with a linear relationship. Such integration has a discernable influence on both the overall model prediction and health effects assessment on the spatial distribution of air pollution in the city region.

Focal mechanism caused by fracture or burst of a coal pillar

As a regional, real-time and dynamic method, microseismic monitoring technology is quite an appropriate technology for forecasting geological hazards, such as rock bursts, mine tremors, coal and gas outbursts and can even be used to prevent or at least reduce these disasters. The study of the focal mechanisms of different seismic sources is the prerequisite and basis for forecasting rock burst by microseismic monitoring technology. Based on the analysis on the mechanism and fracture course of coal pillars where rock bursts occur mostly, the equivalent point source model of the seismicity caused by a coal pillar was created. Given the model, the seismic displacement equation of a coal pillar was analyzed and the seismic mechanism was pointed out by seismic wave theory. The course of the fracture of the coal pillar was simulated closely in the laboratory and the equivalent microseismic signals of the fractures of the coal pillar were acquired using a TDS-6 experimental system. The results show that, by the pressure and friction of a medium near the seismic source, both a compression wave and a shear wave will be emitted and shear fracture will be induced at the moment of breakage. The results can be used to provide an academic basis to forecast and prevent rock bursts or tremors in a coal pillar.

Sedimentation retention basin utilization for best management practice

Approaches to the artificial impoundment and theoretical design of sedimentation retention basin are reviewed with particular attention to best management practice(BMP) to control agriculture and surface runoff. Sediments retention basins are the small version of farm pond used where a criteria of farm pond is not met. Such basin traps the pollutants and suspended solids prior to entry into streams and lakes. The study is focused with special reference to the assessment and control of non point source pollution(NPSP) from the sub basin area of Tai Lake in the Xishan County of Wuxi City of China. The author suggested two different approaches to conduct this study including theoretical design for sedimentation retention basin and computation of flow, sediment transport and deposition during the artificial impoundment of retention basin for BMP's utilization. Theoretical design will provide a useful function as a first line defense against the movement of sediments and transport of pollutants into the Tai Lake while the assessment of sediments deposition will help to make its proper use and periodic cleanup.

The simulation of ultrasonic beams with a Gaussian beam equivalent point source model

Point Sources and Gaussian beams are used frequently as fundamental building blocks for developing ultrasonic beam models. Both these models have different weaknesses that limit their effectiveness. Here, we will show that one can develop a Gaussian Beam Equivalent Point Source （GBEPS） model that removes those weaknesses and combines the accuracy and versatility of the point source models with much of the speed and well-behaved nature of Gaussian beam models. We will demonstrate the efficiency and versatility of this new GBEPS model in simulating the beams generated from ultrasonic phased arrays, using as few as one Gaussian beam per element of the array. A single element GBEPS model will be shown to be as accurate as a point source model even when substantial beam focusing or steering is present in the array or where the array beam is transmitted through an interface. At the same time the GBEPS model will be shown to be several orders of magnitude faster than the point source model.

General Solutions of Thermoelastic Plane Problems of Two-Dimensional Quasicrystals

The thermoelastic plane problems of two-dimensional decagonal quasicrystals(QCs)are systematically investigated.By introducing a displacement function,the problem of thermoelastic plane problems can be simplified to an eighth-order partial differential governing equation,and then general solutions are presented through an operator method.By virtue of the Almansi′s theorem,the general solutions are further established,and all expressions for the phonon,phason and thermal fields are described in terms of the potential functions.As an application of the general solution,for a steady point heat source in a semi-infinite quasicrystal plane,the closed form solutions are presented by four newly induced harmonic functions.

An end-to-end 3D seismic simulation of underground structures due to point dislocation source by using an FK-FEM hybrid approach

Based on the domain reduction idea and artificial boundary substructure method,this paper proposes an FK-FEM hybrid approach by integrating the advantages of FK and FEM(i.e.,FK can efficiently generate high-frequency three translational motion,while FEM has rich elements types and constitutive models).An advantage of this approach is that it realizes the entire process simulation from point dislocation source to underground structure.Compared with the plane wave field input method,the FK-FEM hybrid approach can reflect the spatial variability of seismic motion and the influence of source and propagation path.This approach can provide an effective solution for seismic analysis of underground structures under scenario of earthquake in regions where strong earthquakes may occur but are not recorded,especially when active faults,crustal,and soil parameters are available.Taking Daikai subway station as an example,the seismic response of the underground structure is simulated after verifying the correctness of the approach and the effects of crustal velocity structure and source parameters on the seismic response of Daikai station are discussed.In this example,the influence of velocity structure on the maximum interlayer displacement angle of underground structure is 96.5%and the change of source parameters can lead to the change of structural failure direction.