Improving performance of optical fibre chaotic communication by dispersion compensation techniques

This paper numerically investigates the effects of dispersion on optical fibre chaotic communication, and proposes a dispersion compensation scheme to improve the performance of optical fibre chaotic communication system. The obtained results show that the transmitter-receiver synchronization progressively degrades and the signal-to-noise ratio of the recovered message deteriorates as the fibre length increases due to the dispersion accumulation. Two segments of 2.5-km dispersion-compensating fibres are symmetrically placed at both ends of a segment of 245-km nonzero dispersionshifted fibre with low dispersion in one compensation period. The numerical results show that the signal-to-noise ratio of the extracted 1 GHz sinusoidal message is improved from -2.92 dB to 15.38 dB by this dispersion compensation for the transmission distance of 500 km.

Dispersion compensation in an open-loop all-optical chaotic communication system

The optical chaotic communication system using open-loop fiber transmission is studied under strong injection conditions. The optical chaotic communication system with open-loop configuration is studied using fiber transmission under strong injection conditions. The performances of fiber links composed of two types of fiber segments in different dispersion compensation maps are compared by testing the quality of the recovered message with different bit rates and encrypted by chaotic modulation （CM） or chaotic shift keying （CSK）. The result indicates that the performance of the pre-compensation map is always worst. Two types of symmetrical maps are identical whatever the encryption method and bit-rate of message are. For the transmitting and the recovering of message of lower bit rate （1 Gb/s）, the post-compensation map is the best scheme. However, for the message of higher bit rate （2.5 Gb/s）, the parameters in communication system need to be modified properly in order to adapt to the high-speed application. Meanwhile, two types of symmetrical maps are the best scheme. In addition, the CM method is superior to the CSK method for high-speed applications. It is in accordance with the result in a back-to-back configuration system.

High-speed polarization mode dispersion compensation in a 43-Gb/s RZ-DQPSK transmission system over 1200 km of standard single-mode fibre

This paper reports that the designed optical polarization mode dispersion compensator shows a good performance under the real-time variation of differential group delay, state of polarization and principal state of polarization in a （40×43）-Gb/s dense-wavelength-multiplexing, 1200-km enhanced return-to-zero differential-quadrature-phase-shift- keying （RZ-DQPSK） system. The polarization mode dispersion tolerance of the system is improved by 26 ps using the optical polarization mode dispersion compensator. The short and long time stabilities are tested with the bit error ratio recorded.

Dispersion compensation for an ultrathin metal film using LCD-CCD system

A dispersion compensation method is introduced to correct the distorted image passing through an ultrathin metal film.An LCD-CCD system is modeled by the back propagation network and used to evaluate the transmittance of the ultrathin metal film.Training samples for the network come from 729 images captured by shooting test patches,in which the RGB values are uniformity distributed between 0 and 255.The RGB value of the original image that will be distorted by the dispersion is first transformed by mapping from the LCD to the CCD,multiplied by the inverse matrix of the transmittance matrix,and finally transformed by mapping from the CCD to the LCD,then the corrected image is obtained.In order to verify the effectiveness of the proposed method,ultrathin aluminum films with different thicknesses are evaporated on glass substrates and laid between the CCD and LCD.Experimental results show that the proposed method compensates for the dispersion successfully.

Design of Dispersion Compensation and Nonlinear Distortion Self-compensationin Co -network Transmission Systems

Dispersion and nonlinear distortion have an effect on transmission performanc es of optic al fiber transimission systems. The schemes of dispersion compensation and nonli near distortion self-compens ation in telecom-CATV co-network transmission systems are reported, followed by investigation on (1) the impact of dispersion compensation fiber (DCF) on fi ber nonlinear effects with a cascade of erbium-doped fiber amplifiers (EDFAs) an d different dispersion compensation schemes, (2) the impact of the complex on th e total nonlinear distortion induced by EDFA gain tilt and the light source. As a result , dispersion compensation optimal scheme and EDFA negative gain tilt are suggest ed as a solution to dispersion compensation and the nonlinear distortion self-c ompensation.

Research on Dispersion Compensation of 40 GB/s Optical Duo-Binary Coded Transmission System

A 40 Gb/s high speed optical transmission system is designed, and the different dispersion compensation schemes are adopted to realize the transmission of the optical duo-binary (ODB) signals over 120 km optical fiber. Optical duo-binary signals are generated by using a precoder, two low- pass filters (LPF) and one mach-zehnder modulator (MZM). Through combination of dispersion compensation fiber (DCF) and single mode fiber (SMF) in the transmission link, four different dispersion compensation schemes (pre-compensation, post-compensation and hybrid compensation (pre+ post) and hybrid compensation (post+ pre)) were compared. Analyzing Q factor, BER, eye diagrams and receiver sensitivity in several dispersion compensation schemes, the simulation results are: the cut-off frequency of LPF affects the transmission performance, and the hybrid compensation (post+ pre) scheme is the optimal dispersion compensation method.

Seismic energy dispersion compensation by multi-scale morphology

Seismic energy decays while propagating subsurface, which may reduce the resolution of seismic data. This paper studies the method of seismic energy dispersion compensation which provides the basic principles for multi-scale morphology and the spectrum simulation method. These methods are applied in seismic energy compensation. First of all, the seismic data is decomposed into multiple scales and the effective frequency bandwidth is selectively broadened for some scales by using a spectrum simulation method. In this process, according to the amplitude spectrum of each scale, the best simulation range is selected to simulate the middle and low frequency components to ensure the authenticity of the simulation curve which is calculated by the median method, and the high frequency component is broadened. Finally, these scales are reconstructed with reasonable coefficients, and the compensated seismic data can be obtained. Examples are shown to illustrate the feasibility of the energy compensation method.

The Analysis and Research of Chirped Bragg Fiber GratingTheory on Dispersion Compensation

Based on the general theory of linear Chirped Bragg fiber grating, this paper discusses some parameters including different chirped values and quasi gauss coupling function relating with the reflectivity coefficient dispersion compensation.The result shows that selecting larger chirped value and appropriate qusi guass coupling function can improve the dispersion compensation while ensuring high reflectivity. The concept of "figure of merit" in the microwave field is introduced to quantize the equalizing power of the dispersion compensator.

The system of L-band 2 × 10 Gb/s WDM transmission over conventional single mode fibre with 600 km by chirped fibre Bragg gratings dispersion compensation

A chirped fibre Bragg grating according to ITU-T suggested L-band （2nd channel λ1 = 1570.83 nm; 80th channel λ2 = 1603.57 nm） with more than 1800 ps/nm single channel dispersion compensation is presented in this paper, of which the cladding mode loss, the delay curve ripple and the power fluctuation of the reflected spectrum are less than 0.5 dB, 50 ps and 0.25 dB, respectively. With this new FBG as dispersion compensation device, a 2 × 10 Gb/s wavelength division multiplexing （WDM） L-band transmission of 600 km based on conventional single mode fibre （G.652 fibre） is performed without forward error correction. The bit error rate （BER） is less than 10-12 and the power penalties of the 2nd and 80th channel of L-band are 1.8 dB and 2.0 dB, respectively.

A Method for Dispersion Compensation Based on GLM Theory

A method used to design the waveguide gratings for dispersion compensation employing GLM theory is briefly described. By using this method a reflective grating is designed, which has both a flat amplitude and a quadratic phase response over the transfer bandwidth.

DISPERSION COMPENSATION CFBG IN 100km 10Gbit/s RECIRCULATING SYSTEMS

A 10 Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4× 167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of ±5GHz.At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.

PSO-based Control Algorithm for Polarization Mode Dispersion Self-adaptive Compensation

Polarization mode dispersion(PMD) is considered to be the ultimate limitation in high-speed optical fiber communication systems. Establishing an effective control algorithm for adaptive PMD compensation is a challenging task, because PMD possesses the time-varying and statistical properties. The particle swarm optimization(PSO) algorithm is introduced into self-adaptive PMD compensation as feedback control algorithm. The experiment results show that PSO-based control algorithm has some unique features of rapid convergence to the global optimum without being trapped in local sub-optima and good robustness to noise in the optical fiber transmission line that has never been achieved in PMD compensation before.

Investigation of Dispersion Compensation in 2.5 Gbit/s OOK Label and 40 Gbit/s RZ-DPSK Payload Optical Label Switching System Based on Optical Carrier Suppression and Separation

Three dispersion compensation schemes of an optical label switching transmission system were investigated, which employs 40 Gbit/s return zero differential phase-shift keying（RZ-DPSK） payload labeled with 2.5 Gbit/s on-off keying（OOK） signal based on the optical carrier suppression and separation（OCSS） techniq ue, In the system, proposed are the receiver sensi ti vity oS payload and label, achieving -- 32. 4 dBm and --38.5 dBm, respectively. Using the optimal dispersion compensation scheme, after transmitted over 160 km and 320 km SMF respectively, the label can be recovered without power penalty, while the payload can be recovered with less than 2 dB and 5 dB penalty, respectively.

Multichannel Adaptive Polarization Mode Dispersion Compensation with One Compensator in Dense Wavelength Division Multiplexing Transmission Systems

A simple two-section polarization mode dispersion(PMD) compensator is proposed for multichannel PMD compensation, which can compensate two or even more channels simultaneously. Because of the statistical characteristics and the frequency-dependence of PMD, for current single mode fiber with moderate PMD, the probability that all channels are severely degraded at the same time is extremely small, which makes it possible to compensate a dense wavelength division multiplexing(DWDM) transmission system with moderate PMD using this compensator. It is shown that the outage probability of a 40×43 Gb/s DWDM transmission system using this compensator is decreased significantly from 3.6×10-3 to 3.6×10-5.

Suppression of the interactions between fibre gratings used as dispersion compensators in dense wavelength-division multiplexing systems

Chirped fibre Bragg gratings （CFBGs） are required to be concatenated to compensate the fibre dispersion in the dense wavelength-division multiplexing （DWDM） systems. When the channel spacing is small, the performance of CFBGs is degraded, which restricts the usage of fibre gratings. The origin of the interactions between the gratings is analysed and methods of suppressing the interactions are also proposed.

Microwave frequency transfer over a 112-km urban fiber link based on electronic phase compensation

We demonstrate the transmission of a microwave frequency signal at 10 GHz over a 112-km urban fiber link based on a novel simple-architecture electronic phase compensation system.The key element of the system is the low noise frequency divider by 4 to differentiate the frequency of the forward signal from that of the backward one,thus suppressing the effect of Brillouin backscattering and parasitic reflection along the link.In terms of overlapping Allan deviation,the frequency transfer instability of 4.2×10-15 at 1-s integration time and 1.6×10-18 at one-day integration time was achieved.In addition,its sensitivity to the polarization mode dispersion in fiber is analyzed by comparing the results with and without laser polarization scrambling.Generally,with simplicity and robustness,the system can offer great potentials in constructing cascaded frequency transfer system and facilitate the building of fiber-based microwave transfer network.

Impact of Fiber Dispersion on Performance of Entanglement-Based Dispersive Optics Quantum Key Distribution

Dispersive optics quantum key distribution(DO-QKD)based on energy-time entangled photon pairs is an important QKD scheme.In DO-QKD,the arrival time of photons is used in key generation and security analysis,which would be greatly affected by fiber dispersion.In this work,we establish a theoretical model of the entanglement-based DO-QKD system,considering the protocol,physical processes(such as fiber transmission and single-photon detection),and the analysis of security tests.Based on this theoretical model,we investigate the influence of chromatic dispersion introduced by transmission fibers on the performance of DO-QKD.By analyzing the benefits and costs of dispersion compensation,the system performance under G.652 and G.655 optical fibers are shown,respectively.The results show that dispersion compensation is unnecessary for DO-QKD systems in campus networks and even metro networks.Whereas,it is still required in DO-QKD systems with longer fiber transmission distances.

Wideband dispersion removal and mode separation of Lamb waves based on two-component laser interferometer measurement

Ultrasonic Lamb waves are considered as a sensitive and effective tool for nondestructive testing and evaluation of plate-like or pipe-like structures. The nature of multimode and dispersion causes the wave packets to spread, and the modes overlap in both time and frequency domains as they propagate through the structures. By using a two-component laser interferometer technique, in combination with a priori knowledge of the dispersion characteristics and wave structure information of Lamb wave modes, a two-component signal processing technique is presented for implementing dispersion removal and mode separation simultaneously for two modes mixture signals of Lamb waves. The proposed algorithm is first processed and verified using synthetic Lamb wave signals. Then, the two-component displacements test experiment is conducted using different aluminum plate samples. Moreover, we confirm the effectiveness and robustness of this method.

Dispersion Monitoring Techniques in High Bit-rate Optical Communication Systems

For the efficient dynamic dispersion compensation, it is essential to monitor the dispersion accurately. The existing main dispersion monitoring techniques in high bit-rate optical communication systems are presented as well as their operating principles and research progress. The advantages and disadvantages of these methods are analyzed and discussed.

Ultra broadband flat dispersion tailoring on reversed-rib chalcogenide glass waveguide

In this paper,we introduce a horizontal slot in the reversed-rib chalcogenide glass waveguide to tailor its dispersion characteristics.The waveguide exhibits a flat and low dispersion over a wavelength range of 1080 nm,in which the dispersion fluctuates between-10.6 ps·nm-1·km-1 and ＋11.14 ps·nm-1·km-1.The dispersion tailoring effect is due to the mode field transfer from the reversed-rib waveguide to the slot with the increase of wavelength,which results in the extension of the low dispersion band.Moreover,the nonlinear coefficient and the phase-matching condition of the fourwave mixing process in this waveguide are studied,showing that the waveguide has great potential in nonlinear optical applications over a wide wavelength range.